ISO 13628-2:2006 defines the technical requirements for safe, dimensionally and functionally interchangeable flexible pipes that are designed and manufactured to uniform standards and criteria. Minimum requirements are specified for the design, material selection, manufacture, testing, marking and packaging of flexible pipes, with reference to existing codes and standards where applicable.
ISO 13628-2:2006 applies to unbonded flexible pipe assemblies, consisting of segments of flexible pipe body with end fittings attached to both ends. ISO 13628-2:2006 applies to both static and dynamic flexible pipes used as flowlines, risers and jumpers. The applications addressed by this ISO 13628-2:2006 are sweet and sour service production, including export and injection applications for production products including oil, gas, water and injection chemicals.
ISO 13628-2:2006 does not cover flexible pipes of bonded structure or flexible pipe ancillary components or to flexible pipes for use in choke-and-kill line applications.
ISO 13628-2:2006 does not apply to flexible pipes that include non-metallic tensile armour wires.

  • Standard
    78 pages
    English language
    e-Library read for

This document specifies the grades and the corresponding requirements for ausferritic spheroidal graphite cast irons.
This document specifies five grades of ausferritic spheroidal graphite cast iron by a classification based on mechanical properties measured on machined test pieces prepared from cast samples. One grade also has additional but optional requirements for room temperature and notched-impact.
This document also specifies two grades by a classification as a function of hardness.
This document does not cover technical delivery conditions for iron castings.
NOTE   For further details, see EN 1559-1:2011 and EN 1559-3:2011.

  • Draft
    44 pages
    English language
    e-Library read for

This document specifies long-term measurement methods to obtain trackside noise emission values of multiple trains passing by, automated and unattended, of all kinds of vehicles operating on rails in regular operation, taking into consideration the specific environmental, track and vehicle conditions.
It specifies conditions the measurement setup, data analysis and data processing methods.
The results are datasets of pass-by sound pressure levels or third octave spectra for different sites, train types, units (vehicles) which can be used for different reporting objectives and data analysis. The following are described within the document:
-   comparison of results from different scenarios, e.g. to evaluate the noise reduction of innovative techniques or acoustically relevant modifications to the track structure on a particular track section;
-   trend analysis;
-   averaging procedures, e.g. for determination of acoustic parameters for source term calculations as given in EN 17936 or sites with other infrastructure related sources (such as bridges, crossings, switching, impact noise, curving noise).
This document is not applicable to:
-   type testing;
-   attended measurements;
-   parked or stationary vehicles;
-   shunting yards;
-   positions beyond 25 m from the track;
-   obstructed positions such as behind barriers or around dwellings.
NOTE      The procedures specified in this normative document are of survey grade (grade 2) as defined in EN ISO 12001.

  • Technical specification
    36 pages
    English language
    e-Library read for

This document provides trustworthiness requirements and guidance for data space participants in support of trusted data transactions.
Specifically, it defines a set of foundational principles for trusted data transactions, and establishes general requirements and guidance that apply to all phases of a trusted data transaction, and specific requirements for each phase of a trusted data transaction.
This document applies to all types of organizations participating in data spaces, regardless of their type or size.

  • Standard
    25 pages
    English language
    e-Library read for

This document specifies a method for the determination of the fines mixing time of diluted cationic bituminous emulsions, under standardized conditions.
WARNING - Use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to identify the hazards and assess the risks involved in performing this test method and to implement sufficient control measures to protect individual operators (and the environment). This includes appropriate safety and health practices and determination of the applicability of regulatory limitations prior to use.

  • Draft
    12 pages
    English language
    e-Library read for

This document specifies a standardized level framework for the implementation of additive manufacturing to support temporary self-sufficient systems. It defines principles and criteria, from a resource perspective (personnel, training, infrastructure, materials, etc.) and provides guidance for categorizing additive manufacturing processes into different levels to support self-sufficient systems (ships, small islands, oil rigs, etc.). Support can be established through onboard and onshore operation. This covers the complete part cycle from design (if applicable), manufacturing, to a finished part that meets requirements.
It aims to provide clarity and consistency for non-AM experts dealing with logistical support of self-sufficient systems.
This document is applicable to industries, military institutions, research institutions, and regulatory bodies involved in additive manufacturing, facilitating interoperability and harmonization of practices across different stakeholders.

  • Draft
    16 pages
    English language
    e-Library read for

This document gives specific procedures for industrial X-ray and gamma radiography for discontinuity detection purposes, using NDT (non-destructive testing) film techniques. This part of the EN 12681 series specifies the requirements for film radiographic testing of castings.
Films after exposure and processing become radiographs with different area of optical density. Radiographs are viewed and evaluated using industrial radiographic illuminators.
This part of the EN 12681 series specifies the recommended procedure for the choice of operating conditions and radiographic practice.
These procedures are applicable to castings produced by any casting process, especially for steel, cast iron, aluminium, cobalt, copper, magnesium, nickel, titanium, zinc and any alloys of them.
NOTE   This document considers EN ISO 5579.
This document does not apply to:
-   radiographic testing of castings for aerospace applications (see EN 2002-21);
-   radiographic testing of welded joints (see EN ISO 17636-1);
-   radiography with digital detectors (see EN 12681-2);
-   radioscopic testing (see the EN 13068 series).

  • Draft
    49 pages
    English language
    e-Library read for

This document specifies a method for the determination of the breaking value of cationic bituminous emulsions.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Draft
    18 pages
    English language
    e-Library read for

This document gives specific procedures for industrial X-ray and gamma radiography for discontinuity detection purposes, using NDT (non-destructive testing) digital X-ray image detectors. This part of the EN 12681 series specifies the requirements for digital radiographic testing by either computed radiography (CR) or radiography with digital detector arrays (DDA) of castings.
Digital detectors provide a digital grey value image which can be viewed and evaluated using a computer.
NOTE   This part of the EN 12681 series complies with EN ISO 16371-2 for CR. Some clauses and annexes are taken from EN ISO 17636-2.
This part of the EN 12681 series specifies the recommended procedure for detector selection and radiographic practice. Selection of computer, software, monitor, printer and viewing conditions are important but are not the main focus of this document. The procedure specified in this document provides the minimum requirements for radiographic practice which permit exposure and acquisition of digital images with equivalent sensitivity for detection of imperfections as film radiography, as specified in EN 12681-1.
This document does not consider radiographic or radioscopic fitness for purpose testing as applied for specific castings based on manufacturer’s internal requirements and procedures.
The requirements on image quality in testing class A and B testing of Annex A consider the good workmanship quality for general casting applications as also required in EN 12681-1 for film radiography.
The testing classes AA and BA reflect the quality requirements of current automated and semi-automated radiographic testing systems with DDAs and computer- or operator-based image evaluation, and mini- or micro-focus tubes (spot size ≤ 1 mm) with reduced requirements to the unsharpness, but unchanged requirements to contrast sensitivity as also required in EN 12681-1 for film radiography.
The specified procedures are applicable to castings produced by any casting process, especially for steels, cast irons, aluminium, cobalt, copper, magnesium, nickel, titanium, zinc and any alloys of them.
This document does not apply to:
-   the testing of welded joints (see EN ISO 17636-2);
-   film radiography (see EN 12681-1);
-   real time testing with radioscopy (see EN 13068-1; radioscopy with image intensifiers).

  • Draft
    66 pages
    English language
    e-Library read for

This document gives guidance on the sample preparation of milk and milk products for physical and chemical analysis, including analysis by applying instrumental methods.
This document specifies the (sub)sampling and sample preparation steps carried out after sampling in accordance with ISO 707 | IDF 50 [1] and prior to method-specific sample preparations (e.g. as with analytical methods).
NOTE            Analysis on volatile substances, minor components or allergens can require additional precautionary measures in sample preparation in order to avoid loss of or contamination with one or more target analytes.

  • Draft
    14 pages
    English language
    e-Library read for

This document specifies requirements for phased array ultrasonic examination of steel castings with low ultrasonic attenuation. It is applicable to ferritic, bainitic and martensitic microstructures. It specifies the registration levels and acceptance criteria.
This document is applicable to the ultrasonic examination of steel castings with a wall thickness of 600 mm or less.
For higher wall thicknesses, special agreements apply regarding the test procedure and recording levels.
This document does not apply to austenitic steels and cast irons, lamellar graphite and spheroidal cast irons and welded assemblies. For other ferrous materials, this document gives guidance. The registration levels and acceptance criteria are to be adapted.
In this document, phased array is used both for phased array technique and TFM technique.

  • Draft
    23 pages
    English language
    e-Library read for

This document describes a laboratory test method for determining the key parameters for evaluating the level of technical recyclability of a paper-based material and product using a white or off-white substrate, emulating the relevant phases of paper and board mills with alkaline flotation deinking recycling process.
The assessment of the technical recyclability is out of the scope of this document.

  • Draft
    54 pages
    English language
    e-Library read for

This document defines terms and specifies procedures for the characterization of mass spectrometer leak detectors (MSLD). This document is not intended to provide a complete set of specifications for acceptance testing, but rather a description of procedures that can be applied without specialized calibration equipment.
The methods described in this document are applicable without restrictions to helium as the tracer gas. For other gases, additional precautions might be necessary.
These methods are applicable to commonly available MSLD, based on the present level of technology, which might be able to measure leakage rates down to 10−12 Pa⋅m3/s.

  • Draft
    24 pages
    English language
    e-Library read for

This document specifies a procedure to qualify a preliminary welding procedure specification (pWPS) by welding procedure tests to produce a qualified welding procedure specification (WPS).
NOTE 1   The application of this document ensures that the qualification of the pWPS is carried out according to a uniform test procedure.
NOTE 2   The primary purpose of a welding procedure qualification is to demonstrate that the joining process proposed for construction is capable of producing joints having the required mechanical properties for the intended application.
This document applies to the following thermoplastic welding processes:
-    hot gas welding: round nozzle, speed, wedge;
-    extrusion welding;
-   heated tool welding: butt, socket, wedge.
This document applies to the welding of the following products:
-   sheet;
-   pipe (unreinforced, solid wall only);
-   fittings (unreinforced only);
-   lining membrane/
This document covers the welding of the following groups of materials:
a)      for sheets, pipes and fittings:
-   PVC (PVC-U, PVC-C);
-   PP (PP-B, PP-H, PP-R);
-   PE;
-   PVDF;
-   ECTFE, PFA and FEP;
b)   for lining membranes:
-   PVC-P;
-   PE;
-   ECB;
-   PP;
c)   for pipes and fittings only:
-   PA-U (PA-U 11, PA-U 12).

  • Draft
    21 pages
    English language
    e-Library read for

This document specifies part properties, design freedom, strengths and applications of additively manufactured (AM) ceramic materials. It is aimed at product planners and designers and provides the necessary basic knowledge about ceramics and the possibilities specific to AM ceramics, including strengths and limitations of the most utilized ceramic AM process categories. In-depth previous knowledge in these areas is not assumed.

  • Draft
    28 pages
    English language
    e-Library read for

This document describes a laboratory test method for determining the key parameters for evaluating the level of technical recyclability of a paper-based material and product, emulating the relevant phases of paper and board mills with specialized recycling processes. This method applies to several specialized processes where different key parameters are determined depending on the type of a paper-based material and product (e.g. liquid packaging cartons).
The assessment of the technical recyclability is out of the scope of this document.

  • Draft
    40 pages
    English language
    e-Library read for

This document specifies the acceptable quantitative and qualitative microbiological limits in finished cosmetic products. It is applicable to all cosmetics, and assists interested parties in the assessment of the microbiological quality of cosmetic products.

  • Draft
    10 pages
    English language
    e-Library read for

This document specifies a method for the determination of the water content in bituminous emulsions by means of azeotropic distillation.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Draft
    11 pages
    English language
    e-Library read for

This document specifies a method of assessing the behaviour of protection sleeves or conduits subject to an external electric arc at 115 VAC, 800 Hz.
This document is used in conjunction with EN 6059-100.
The primary aim of this test is to produce, in a controlled fashion, electric arcs at the immediate vicinity of a protection sleeve or conduit and to examine possible consequences on the protected cables bundle, which supposed to be maintained in a safe condition.
These electric arcs are representative of those which may occur in service when a typical adjacent cable bundle is severely damaged and leading to an electrical arc default.
In order to optimize thickness and mass of such protection, it is necessary to associate a nominal current limit In to each sleeves or conduits construction.
Two levels of prospective fault current are specified for all protection sizes.
NOTE   This test requires specifics attentions and protections toward operator and personnel applying this test, refer to 6.2 for further details.

  • Draft
    16 pages
    English language
    e-Library read for

This document specifies methods for the determination of silicon, nitrogen, aluminium, iron, calcium, oxygen, carbon, fluorine, and chlorine in silicon nitride powders.
This document is applicable for the chemical analysis of silicon nitride powders used as raw material for fine ceramics.

  • Standard
    40 pages
    English language
    e-Library read for

This document specifies the test procedures for roadside equipment (RSE and on-board equipment (OBE for electronic fee collection (EFC) with regard to conformance to standards and requirements for type approval and acceptance testing.
The scope of this document is restricted to systems operating within the radio emission, electromagnetic compatibility (EMC) regulations, traffic, and other regulations of the regions in which they are operated.
This document identifies a set of suitable parameters and provides test procedures to enable the proof of a complete EFC system, as well as components of an EFC system, e.g. OBE, related to the defined requirements of an application. The defined parameter and tests are assigned to the following groups of parameters:
functionality;
quality;
referenced pre-tests.
This document describes procedures, methods and tools, and a test plan which shows the relation between all tests and the sequence of these tests. It lists all tests that are required to measure the performance of EFC equipment. It describes which EFC equipment is covered by the test procedures; the values of the parameters to be tested are not included. It also describes how the tests are intended to be performed, and which tools and prerequisites are necessary before this series of tests can be undertaken. It is assumed that the security of the system is inherent in the communications and EFC functionality tests, therefore they are not addressed in this document. All tests in this document provide instructions on how to evaluate the test results.
This document defines only the tests and test procedures, not the benchmark values against which they are intended to be measured. The test procedures defined in this document can be used as input, e.g. by scheme owners, for prototype testing, type approvals, tests of installations and periodic inspections.
Related to a conceptual model of an EFC system, this document relates only to the equipment of the user and the service provider.
EFC systems for DSRC consist, in principle, of a group of technical components, which in combination fulfil the functions required for the collection of fees by electronic automatic means. These components comprise all, or most, of the following:
OBE within a vehicle;
OBE containing the communications and computing sub-functions;
optional integrated circuit card which can carry electronic money, service rights, and other secured information;
communication between OBE and RSE based on DSRC;
equipment for the fee collection at the RSE containing the communications and computing sub-functions;
equipment for the enforcement at the roadside;
central equipment for the administration and operation of the system.
The scope of this document relates solely to OBE and RSE and the DSRC interface between OBE and RSE including its functions to perform the fee collection. All the equipment used for enforcement (e.g. detection, classification, localization, and registration) and central equipment are outside the scope of this document.

  • Draft
    89 pages
    English language
    e-Library read for

This document specifies safety requirements and the corresponding test methods for reclined cradles intended for children from birth up to when they start to stand up and infant swings intended for children from birth up to when they start to try to sit up.
This document is also applicable to car seats complying with UN R44 or UN R129 that can be used as type A or type B reclined cradles and/or infant swings according to the instructions for use. If usage as a type A or type B reclined cradle and/or an infant swing is not included in the product information or marketing material, car seats are excluded from the scope of this document.
This document does not apply to reclined cradles or infant swings designed for children with special needs, and/or which fall under the scope of Regulation (EU) 2017/745 (medical devices).
If a reclined cradle or infant swing has several functions or can be converted into another function, the relevant European Standards apply.
Swings falling under the scope of EN 71-8 are excluded from the scope of this document.
NOTE   For the rest of the document, the word “product” will be used when referring at the same time to reclined cradles and infant swings.

  • Draft
    67 pages
    English language
    e-Library read for
  • Draft
    77 pages
    English language
    e-Library read for

This document specifies the fundamental principles and concepts of conformity assessment schemes (programmes) and provides guidelines for understanding, developing, operating or maintaining them.

  • Standard
    60 pages
    English language
    e-Library read for

This document specifies general safety requirements for self-loading mobile concrete mixers (here-after referred to as "SLMs") as defined in ISO 18650-1:2021, with rigid or articulated wheeled chassis.
This document applies to SLMs which are designed for front or rear loading and can be provided with a slewing and/or tilting frame where the rotating drum and the self-loading equipment (lift arms and bucket) are mounted on. SLMs can also be fitted with accessories such as water dosing means and a weighing system.
This document is not applicable to the following:
-   machines designed primarily for earth moving, such as loaders or dumpers (see applicable parts of the EN 474 series);
-   truck mixers (see EN 12609).
This document deals with all significant hazards, hazardous situations and events relevant to SLMs, whether used as intended and under conditions foreseen or under conditions of misuse reasonably foreseeable by the manufacturer (see Annex A).
This document does not provide performance levels required for safety related functions of control systems.
NOTE   A document providing detailed description of safety functions for SLMs and related performance levels required is under development.
This document does not address hazards that can occur:
-   during manufacture;
-   when using SLMs on public roads, where specific local road regulations can apply;
-   when operating in potentially explosive atmospheres.
This document does not address hazards specifically related to:
-   SLMs designed to operate with varying levels of autonomy or when SLMs have embedded safety-systems with fully or partially self-evolving behaviour or logic using machine learning approaches, including collaborative applications;
-   SLMs when intended to be connected to the internet or to an external network or device that communicates with it (protection against corruption).
This document is not applicable to SLMs manufactured before the date of its publication.

  • Standard
    52 pages
    English language
    e-Library read for

This document describes the state of knowledge resulting from Urban Rail experiences regarding the design of the axle, and further steps to be investigated.
CEN-CENELEC Guide 26 from 1st of June 2013 or EN 17343:2023 defines Urban Rail Systems.
This document:
—   is applicable for the assessment of new axle designs for urban rail vehicles;
—   defines EN 13103-1 as basic calculation method2;
—   defines the calculation procedure of an operational index depending on track layout, payload, mileage, position of the wheelset axle in vehicle. This procedure is based on the examination of Europe-wide service experiences and calculations made on urban rail wheelset axles running in Germany3;
—   defines the conditions, reflected in this operational index, under which additional assessment steps may be needed;
—   defines these additional assessment steps, including measurements of bending and torsion moments to derive load collectives representative of normal in-service operating conditions and the determination of equivalent stresses.
The design methodologies described in this document have been determined for axles of urban rail rolling stocks running under normal European conditions.  If there is any doubt as to whether the railway operating conditions are normal, these methodologies should be adapted.
This document applies to:
—   axles defined in EN 13261:2024;
—   axles with outboard bearings ;
—   powered and non-powered axles;
—   solid and hollow axles;
—   all track gauges4.
This document does not apply to tilting vehicles.
The calculation of wheelset axles for special applications (e.g. tamping/lining/levelling machines) may be made according to this document only for the load cases of free-running and running in train formation. This document does not apply to workload cases. They are calculated separately.
2 When no sufficient technical or operational data is available, EN 13103-1 can be used.
3 This Technical Specification reflects the state of knowledge resulting from Urban Rail experiences regarding the design of the axle, built-on by subcommittee DIN specially based for this Technical Specification
4 If the gauge is not standard, certain formulae need to be adapted, e.g. according to EN 13103-1:2017+A1:2022

  • Technical specification
    30 pages
    English language
    e-Library read for

This document specifies two methods for the determination of the tear strength of flexible cellular polymeric materials:
Method A, using a trouser test piece;
Method B, using an angle test piece without a nick.

  • Standard
    17 pages
    English language
    e-Library read for

This document gives guidance on the design of natural ventilation systems and hybrid ventilation systems in non-residential buildings to achieve acceptable indoor air quality. It is applicable to spaces intended for human occupancy in non-residential buildings.
The guidance for design in this document is applicable to natural ventilation systems and hybrid ventilation systems, encompassing the natural ventilation part of the hybrid ventilation systems, only. The type of control and the design process of hybrid ventilation systems is covered by this document.
This document does not set the requirements for the indoor air quality, but utilizes these as input parameters when designing natural ventilation systems and hybrid ventilation systems.
This document does not apply to:
-   thermal comfort and overheating;
-   health risk from exposure to tobacco smoke;
-   air cleaning;
-   design of mechanical ventilation systems.

  • Technical specification
    65 pages
    English language
    e-Library read for

This document provides a method of describing the materials, impregnates and lubricants for various types of yarn and ribbon based packings intended for use as gland seals in mechanical equipment such as pumps, mixers, etc. This document is intended to serve as a guide for packing manufacturers, pump OEM’s and end users. It does not include similar products intended for other duties such as thermal insulation.
Guidance is also given regarding dimensional and physical quality aspects of the packings and requirements for packaging and marking.
Tests are specified for the determination of lubricant content, size and mass.
NOTE 1   The information supplied by the purchaser at the time of enquiry and/or order is given in Annex B.
NOTE 2   All packings are free from introduced asbestos fibres in conformance with Annex XVII of REACH.

  • Standard
    17 pages
    English language
    e-Library read for

This document provides complementary product category rules (c-PCR) for Type III environmental product declarations (EPD) for flat glass and channel shaped glass products for use in buildings and construction works. It describes stages of product’s life cycle considered in the EPD and the processes included in life cycle stages.
Glass-block products are excluded from the scope. All other glass products i.e. intermediate and finished products, intended to be used in buildings and construction works, are in the scope of this document.
Examples of glass products covered by this c-PCR are listed in Annex H.

  • Standard
    36 pages
    English language
    e-Library read for

This document specifies the safety requirements relevant to load-handling functions for rough-terrain variable reach tractors (RTVR tractors). This includes the safety requirements for their permanently mounted equipment (PME).
Fork arms are considered to be part of the PME. RTVR tractors can also be equipped with a variety of attachments (e.g. bale spikes, mowers, sweepers).
This document deals with all the significant hazards, hazardous situations and events relevant to the operation of the PME of RTVR tractors when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A).
This document does not apply to:
—   rough-terrain variable-reach trucks covered by EN 1459 1:2025;
—   slewing rough-terrain variable-reach trucks covered by EN 1459 2:2015+A1:2018;
—   industrial variable reach trucks covered by EN ISO 3691 2:2023;
—   lorry-mounted variable-reach trucks covered by ISO 20297 1:2017;
—   RTVR tractors fitted with tilting or elevating operator position;
—   mobile cranes covered by EN 13000:2010+A1:2014;
—   machines designed primarily for earth moving, even if their buckets and blades are replaced with forks (see the EN 474 series);
—   RTVR tractors designed primarily with variable length load suspension elements (e.g. chain, ropes) from which the load can swing freely in all directions;
—   RTVR tractors designed primarily for container handling;
—   RTVR tractors on tracks;
—   RTVR tractors with articulated chassis;
—   front loaders covered by EN 12525:2000+A2:2010;
—   attachments.
Determination and declaration of sound power level is not addressed by this document.
This document does not cover sales literature.
Consistency of single lever (if fitted) and movement of the RTVR tractor when travelling in the forward direction is not covered by this document.
This document does not address hazards linked to:
—   operation of the RTVR tractor from a position other than the normal operating position or the remote control;
—   gas power systems;
—   gasoline engine systems.
This document does not address hazards which can occur:
a)   when handling suspended loads which can swing freely (additional requirements are given in EN 1459 4:2020+A1:2025);
b)   when using RTVR tractors on public roads;
c)   when operating in potentially explosive atmospheres (additional requirements are given in EN 1755:2024);
d)   when operating underground;
e)   when towing trailers;
f)   when fitted with a personnel work platform (additional requirements are given in EN 1459 3:2015 and EN 1459 9:2021);
g)   when using system capable of controlling the speed of the RTVR tractor as set by the operator (cruise-control).
This document does not provide a method of calculation for fatigue and strength of material.
This document is not applicable to RTVR tractors manufactured before the date of its publication.

  • Draft
    63 pages
    English language
    e-Library read for

This document establishes commonly accepted control objectives, controls and guidelines for implementing measures to protect personally identifiable information (PII) in line with the privacy principles in ISO/IEC 29100 for the public cloud computing environment.
In particular, this document specifies guidelines based on ISO/IEC 27002:2022, taking into consideration the regulatory requirements for the protection of PII which can be applicable within the context of the information security risk environment(s) of a provider of public cloud services. This document is applicable to all types and sizes of organizations, including public and private companies, government entities and not-for-profit organizations, which provide information processing services as PII processors via cloud computing under contract to other organizations.
The guidelines in this document can also be relevant to organizations acting as PII controllers.

  • Draft
    43 pages
    English language
    e-Library read for

This document deals with all significant hazards, hazardous situations or hazardous events relevant to hand-held or hand-operated laser processing machines (HLMs), when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer. HLM is the machine, as defined in ISO 11553-1:2020, 3.7, in which laser radiation is generated, where the laser provides sufficient energy/power to cause a phase transition in a part of the workpiece and where the laser output or workpiece to be processed is guided manually or hand-held during the laser material processing.
This document defines general design requirements of HLM. HLM includes the laser device, beam-guiding device (e.g. mirror, fibre, lenses), beam-shaping device (e.g. telescope, focusing), and controls. The laser assembly as an integral part of the HLM or only the laser processing head is hand-held or hand-operated during the laser material processing.
This document does not apply
to laser processing machines which are remotely controlled by a manual controller (hand-operated controller), such as joy sticks, keyboard, etc., without touching a workpiece or a part mechanically connected with the laser material processing head by using the hand(s) of the operator (user)
to laser processing machines without a drive system which may not belong to machinery. And the laser processing apparatus without moving parts, which may not be considered as machinery in “Type C standard”.
to medical or cosmetic applications for the treatment of living human or animal tissue;
to weapon applications, (e.g. such as with regard to military applications, direct close combat.)
NOTE            “hand-operated laser processing machine” is synonymous with “hand-guided laser processing machine” in this document. Hand-operated laser processing machines often use manual force reduction means such as wheels, supports, etc., for manual positioning of the laser processing heads or the workpieces.
It is applicable to HLMs using laser radiation to process materials.
The purpose of this document is to draw attention to the hazards related to HLMs and to prevent personal injury. Depending on the application and the location/operating conditions of HLMs, a number of different significant hazards can arise. This document describes both the areas of hazards analysis and risk assessment as well as protective measures.
Requirements dealing with noise as a hazard are covered by ISO 11553-3:2013.
This document does not apply to laser products or equipment manufactured solely or expressly for applications which are excluded from the Scope of ISO 11553-1:2020. This document is not applicable for HLMs which have been manufactured before the date of publication of this standard.
HLMs include the following types:
HLMs which are designed as all-in-one laser assembly including the beam delivery/forming(shaping) system and optional features such as gas nozzles, material (e.g. powder, wire) feed system;
HLMs where the relevant devices are connected by a beam guidance system (e.g. optical fibre) and power/control cables to an external laser assembly device and which includes only the beam delivery/forming(shaping) system and optional features such as gas nozzles, material (e.g. powder, wire) feed system;
laser processing machines where the workpiece is manually moved under/relative to the laser beam (see informative Annex A).
The intended use of HLMs covers both:
movement of elements or workpieces by hand to be processed under/relatively to stationary laser beams as shielded , and
movement of the laser processing head (beam shaping device) by hand to move laser beam(s) over or relative to elements or workpieces to be processed.
Laser processing machines, where la

  • Standard
    84 pages
    English language
    e-Library read for

This document provides a privacy framework which:
—    specifies a common privacy terminology;
—    defines the actors and their roles in processing personally identifiable information (PII);
—    describes privacy safeguarding considerations;
—    provides references to known privacy principles for information technology.
This document is applicable to natural persons and organizations involved in specifying, procuring, architecting, designing, developing, testing, maintaining, administering, and operating information and communication technology systems or services where privacy controls are required for the processing of PII.

  • Draft
    27 pages
    English language
    e-Library read for

This Guide outlines the rules for drafting and presenting candidate performance harmonized European Standards (hENs) for construction products under Regulation (EU) 2024/3110, known as the Construction Products Regulation CPR-2024. These standards are subject to a standardization request according to Article 5 of CPR-2024.
This Guide gives rules which are additional to the CEN-CENELEC Internal Regulations (IR) - Part 3 (based on ISO/IEC Directives, Part 2) when this is necessary because of the special provisions of harmonized product standards in the construction sector.
This Guide applies to all new candidate hENs and for new Work Items (WIs) revising/amending existing hENs included in a standardization request in support of CPR-2024.
This guide does not include rules for candidate harmonized European Standards under Regulation (EU) No 305/2011 or for those harmonized European Standards within the framework of Regulation (EU) 2024/3110 that are subject to a standardization request according to Article 7 of this Regulation.

  • Guide
    58 pages
    English language
    e-Library read for

This document defines the general terms and the calculations used to determine the thermohydraulic performance of heat exchangers. It includes the general test procedure and related theories.
This document is intended to be used for acceptance-testing heat exchangers in test facilities such as laboratories, manufacturer test facilities and final installation site.
This document specifies three acceptance levels:
—   level 1 for minimum tolerances;
—   level 2 for nominal tolerances;
—   level 3 for maximum tolerances;
This document constitutes an application-specific standard in line with EN 305 and EN 306.

  • Standard
    46 pages
    English language
    e-Library read for

This document describes the technical features of parcel boxes for end use. This covers technical features such as size of parcels, ergonomics and safety, corrosion and water penetration resistance and security of delivery.

  • Technical specification
    20 pages
    English language
    e-Library read for

This document defines the terms and specifies the requirements, means of categorization, test methods, minimum labelling requirements and instructions for use of the article, for ignition devices (except ignition devices for pyrotechnic articles for vehicles) of the following generic types:
-   igniters;
-   components for pyrotechnic trains;
-   pyrotechnic cords and fuses;
-   delay fuses;
-   fuzes.
NOTE   Safety fuses are subject to Directive 2014/28/EU [9] and therefore not considered in this document.

  • Standard
    104 pages
    English language
    e-Library read for

This document specifies the design, testing and marking requirements for spring loaded pressure relief valves (PRV), for use in liquefied petroleum gas (LPG) cylinders of water capacity of 0,5 l up to and including 150 l.
These PRVs can be either an integral part of a cylinder valve (see EN ISO 14245 [4] and EN ISO 15995 [5]) or a separate device.

  • Standard
    20 pages
    English language
    e-Library read for

1.1   Scope of EN 12309 series
Appliances covered by this EN 12309 series include one or a combination of the following:
-   gas fired sorption chiller;
-   gas fired sorption chiller/heater;
-   gas fired sorption heat pump.
This EN 12309 series applies to appliances only when used for space heating and cooling with or without heat recovery.
This EN 12309 series applies to appliances having flue gas systems of type B and C (according to EN 1749:2020) and to appliances designed for outdoor installations, including type A. EN 12309 does not apply to air conditioners, it only applies to appliances having:
-   integral burners under the control of fully automatic burner control systems;
-   closed system refrigerant circuits in which the refrigerant does not come into direct contact with the water or air to be cooled or heated;
—   mechanical means to assist transportation of the combustion air and/or the flue gas.
The above appliances can have one or more primary or secondary functions (i.e. heat recovery - see definitions in EN 12309-1:2023). In the case of packaged units (consisting of several parts), the standard applies only to those designed and supplied as a complete package.
The appliances having their condenser cooled by air and by the evaporation of external additional water are not covered by this document.
Installations used for heating and/or cooling of industrial processes are not within the scope of these standards.
NOTE   All the symbols given in this text are used regardless of the language used.
1.2   Scope of this document
This document deals with the safety of gas-driven sorption appliances for heating and/or cooling having net heat input not exceeding 70 kW as defined in EN 12309-1:2023. It only applies to appliances:
1)   where the temperature of the water does not exceed 105 °C during normal operation;
2)   where the maximum operating pressure in the water circuit does not exceed 6 bar;
3)   types B12, B13, B22, B23, C12, C13, C32, C33 and C63;
4)   for outdoor installations, including type A appliances.
This document does not include specific requirements on surface temperatures of external parts particular to children and elderly people.

  • Draft
    94 pages
    English language
    e-Library read for

This document provides product category rules (c-PCR), that are complementary to EN 15804:2012+A2:2019, for Type III environmental declarations for sandwich panels within the scope of EN 14509 1:— and EN 14509 2:—, which are used for non-structural and structural purposes in building envelopes and for sandwich panels with perforated faces and for sandwich panels with core materials others than defined in EN 14509 1:— and EN 14509 2:—.
Manufactured on industrial plant, double skin metal faced insulating sandwich panels are designed to be laid with overlapping edges in the following applications:
—   roofs and discontinuous roofing;
—   outer walls and wall cladding;
—   walls (incl. partition walls) and (suspended) ceilings inside the building envelope.
This document is intended to be used cradle-to-grave, declaring modules A1-A3, modules C1-C4 and module D, according to EN 15804:2012+A2:2019
NOTE   The assessment of social and economic performances at product level is not covered by this document.

  • Standard
    33 pages
    English language
    e-Library read for

This document deals with electroplating process evaluation for fasteners, including fastener expected coating properties.
This document is a complement to CQI-11 in order to deal with fastener specific aspects not fully covered by CQI-11, and to clarify some questions/items when they are not fully suitable for fasteners.
This document is applicable to all parties involved in the supply chain for coated fasteners, i.e. fastener manufacturers, chemical suppliers, electroplaters and purchasers.
The requirements for electroplating fasteners specified in this document are essentially based on ISO 4042, ISO/TR 20491 and ISO 16047.
NOTE            Requirements for electroplating fasteners are also given in ASTM F1941/F1941M.

  • Technical specification
    26 pages
    English language
    e-Library read for

This document specifies photometric methods of test for comparing in the visible spectrum:
the tinting strength of two similar coloured pigments dispersed in an alkyd resin without a drier;
the scattering power of two white pigments of the same type dispersed in an alkyd resin without a drier.
This document does not apply to the comparison of coloured pigments that on reduction differ greatly in colour.

  • Standard
    20 pages
    English language
    e-Library read for

This document specifies requirements and technical specifications for information presented in tactile lettering in the built environment.
NOTE   For the definition of built environment see ISO 21542.
It sets out rules for content, design, arrangement and application of information elements so that blind and partially sighted people are able to locate, identify, fluently read and interpret this information.
This document does not specify technical methods for producing tactile lettering.
This document is only applicable to permanently installed tactile lettering.

  • Standard
    28 pages
    English language
    e-Library read for

This document covers the track and trace events for the return flow of e-Commerce items, more specifically, the events that are most useful to the original recipient (if any) and the E-Commerce company that sent the item in the first place.
It provides a minimum set of events formulated in language that is understood by sellers and buyers of E-Commerce products. The logistic service providers (LSPs) involved can "map" their own internal events to the events described in this document.
A return flow is always linked to a forward flow that is the subject of CEN/TS 18055-1.
This document aims to describe only those events that are related to the returns flow. Therefore, this document defines and describes the exact moment that the forward flows stop and the associated return flow starts.
This document covers the following four cases of return flows:
-   unsuccessful delivery (item remains in possession of the last mile operator);
-   return to sender or equivalent party (delivered and later returned parcel);
-   a service for recipients to send (parts of) a received shipment back;
-   returns caused by failure to meet regulatory or cross-border procedure requirements.
Each of these cases will be covered in separate clauses of the document.
NOTE   There are some processes in case 3 that need to occur before the parcel enters into the Returns Flow and they are generally executed by the E-Commerce company (or a party acting on its behalf) ).
This document will not describe those "precursor" processes in any detail, but it will describe the minimum requirements in terms of information needed by the first LSP to be able to start to execute the Return Flow effectively and efficiently. The precursor process is similar to the RMA (= Return Materials Authorization) process used in business-to-business environments.
This document does not cover the logistical flows within the facilities of the producers and sellers of the items. These fall outside the responsibility of the CEN/TC 331 domain.
This document does not cover all events necessary for an LSP to track items within its own facilities.

  • Technical specification
    34 pages
    English language
    e-Library read for

This document gives guidance to the design of ventilative cooling systems while referring to relevant standards to ensure coherence and avoiding overlapping. In this document different design approaches for use of natural, mechanical or hybrid ventilative cooling can be found, starting at the feasibility phase before going into the design phase. In addition, this document gives guidance on where to find additional information on the design, calculation and maintenance of such systems.
This document is applicable to buildings specified according to the thermal indoor environmental aspects used for human occupancy where production processes don’t have a major impact on the indoor environmental quality. This document is applicable to residential and non-residential buildings.
This document applies to all types of buildings: new and retrofit, residential and non-residential.
This document is applicable to:
-   mechanical ventilative cooling
-   natural ventilative cooling
-   hybrid ventilative cooling
-   airing as a supplement to ventilative cooling specifically relevant during e.g. power failures
-   supplementary free cooling as a supplement to ventilative cooling
The design of supplementary free cooling systems and active cooling systems are not part of the normative part of the document. However, the interface between ventilative cooling systems and supplementary free cooling systems as well as the interface between ventilative cooling and active cooling systems are mentioned informatively.
Design of ventilative cooling systems commonly considers other aspects like energy use, acoustic, draught, solar gain control, outdoor air quality, user acceptance, burglary and cleaning and maintenance, though these are not covered in detail in this document.
This document only covers temperature control.
This document does not apply to:
-   moisture control
-   waterborne
-   heat losses.

  • Technical specification
    112 pages
    English language
    e-Library read for

This document specifies the technical delivery requirements for seamless and welded butt-welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austenitic and austenitic-ferritic (duplex) stainless steel without specific inspection requirements.
This document specifies:
—   steel grades and their chemical compositions;
—   mechanical properties;
—   dimensions and tolerances;
—   requirements for inspection and testing;
—   inspection documents;
—   marking;
—   handling and packaging.

  • Standard
    65 pages
    English language
    e-Library read for

This document specifies an accelerated method for the determination of wet-scrub resistance. The determination of cleanability is not covered in the scope of this document.
NOTE            The ability of coatings to withstand wear caused by repeated cleaning operations is an important consideration both from a practical point of view and when comparing and rating such coatings. Since wet-scrub resistance depends not only on the quality of a coating but also on the substrate, the method of application, the drying conditions and other factors, the results obtained are not directly transferable to actual practice. In this document, the evaluation of the coating is based on a defined substrate, a fixed application method, specified drying conditions and a defined method of wet scrubbing.

  • Standard
    25 pages
    English language
    e-Library read for

This document gives the background to the requirements specified in the EN 15427 series of standards and CEN/TS 15427 series of technical specifications.

  • Technical report
    175 pages
    English language
    e-Library read for

This document specifies the additional technical delivery conditions for castings made from all cast iron materials.
This document applies to iron castings produced in sand or permanent moulds or by centrifugal casting, continuous casting or investment casting.

  • Standard
    17 pages
    English language
    e-Library read for