CEN/CLC Guide 36:2026
(Main)Guidance on the rules for the drafting and presentation of candidate performance harmonized standards in support of Regulation (EU) 2024/3110 Construction Products Regulation CPR-2024
- Abstract
This Guide outlines the rules for drafting and presenting candidate performance harmonized European Standards (hENs) for construction products under Regulation (EU) 2024/3110, known as the Construction Products Regulation CPR-2024. These standards are subject to a standardization request according to Article 5 of CPR-2024.
This Guide gives rules which are additional to the CEN-CENELEC Internal Regulations (IR) - Part 3 (based on ISO/IEC Directives, Part 2) when this is necessary because of the special provisions of harmonized product standards in the construction sector.
This Guide applies to all new candidate hENs and for new Work Items (WIs) revising/amending existing hENs included in a standardization request in support of CPR-2024.
This guide does not include rules for candidate harmonized European Standards under Regulation (EU) No 305/2011 or for those harmonized European Standards within the framework of Regulation (EU) 2024/3110 that are subject to a standardization request according to Article 7 of this Regulation.
- Status
- Published
- Publication Date
- 27-Oct-2026
- Technical Committee
- CEN/CLC/Guides - Group for CEN-CENELEC Guides
- Current Stage
- 6060 - Definitive text made available (DAV) - Publishing
- Start Date
- 28-Oct-2026
- Completion Date
- 28-Oct-2026
CEN/CLC Guide 36:2026 is a CEN and CENELEC guide for Technical Committees that draft candidate performance harmonized European Standards (candidate hENs) for construction products under Regulation (EU) 2024/3110, the Construction Products Regulation CPR-2024. It sets the drafting and presentation rules for those standards so they match the standardization request and the special structure used for construction-product harmonized standards.
What does CEN/CLC Guide 36:2026 specify?
CEN/CLC Guide 36:2026 applies to new candidate hENs and to new Work Items (WIs) that revise or amend existing hENs included in a standardization request for CPR-2024. It gives extra rules to the CEN-CENELEC Internal Regulations - Part 3 when the construction-products context needs more specific guidance.
The guide does not cover candidate harmonized European Standards under Regulation (EU) No 305/2011, and it does not cover CPR-2024 harmonized European Standards that fall under Article 7 of that Regulation.
The document is organized around the usual front matter and the drafting body of the standard, then Annex ZA.
- Clauses 1 to 3 cover scope, normative references, and general principles.
- Clause 4 gives the required format of a harmonized European Standard for construction products.
- Annex ZA is informative but central in practice because it links the standard to Regulation (EU) 2024/3110.
- The bibliography is limited to supporting documents.
What are the key requirements of CEN/CLC Guide 36:2026?
Keep the candidate hEN tied to the standardization request
CEN/CLC Guide 36:2026 says the candidate hEN should stay coherent with the standardization request and include only the products, intended uses, essential characteristics, assessment methods and other provisions that the request supports. In practice, this keeps the standard focused on the CPR-2024 task and avoids unrelated product content.
The guide also says that content not dealing with CPR-2024 implementation should not be included. Where a deviation from the request is unavoidable, it needs justification and Member State agreement.
Draft the scope, references and definitions precisely
Clause 1 requires a precise scope that identifies the covered products, forms, kits or materials, the intended uses, and the exclusions. It should also show the link between the product, its intended use and the relevant essential characteristics, because users need to know exactly what the standard covers.
Clause 2 says normative references must be dated and should be EN, ISO, IEC or ETSI standards unless the request allows otherwise. The guide also excludes quality management system standards and certification provisions from normative references in product standards.
Clause 3 requires only the terms that are actually used later in the text. It also adds the term product group, which lets one assessment result cover several product types when documented technical justification shows that the result is representative.
Present characteristics as performance-based clauses
Clause 4 requires essential characteristics to be expressed as performance, not as technology-specific design instructions. The guide allows performance to be stated as a value, a class or a description, and it asks the drafting body to link each characteristic to the relevant assessment method in Clause 5.
For practical use, this means the standard should tell the manufacturer what to declare, how it is measured or calculated, and whether thresholds or classes apply. The guide also includes model wording for declaration without testing, declaration without further testing, and declaration based on tabulated values where the legal act allows it.
Clause 4 groups characteristics into the main subject areas used in construction products, including structural and durability assessment, fire-related characteristics, dangerous substances, and environmental sustainability. That structure helps a manufacturer or notified body find the right method for each declared characteristic.
Set out sampling, testing, assessment and verification clearly
Clause 5 requires the standard to state the information needed for each assessment method. It covers release and emission of dangerous substances and environmental sustainability separately, so the methods match the characteristic being declared.
Clause 6 then sets out assessment and verification. It covers type-testing, type calculation, tabulated values, documentation-based performance, factory production control (FPC), technical documentation, and the definition of product type and product category.
The guide also assigns tasks between the manufacturer and the notified body according to the applicable assessment and verification system (AVS). In practice, this tells each party who tests, who validates, who checks documentation, and when audit testing or surveillance applies.
Include product information, safety information, marking and Annex ZA where needed
Clause 7 provides guidance for general product information, instructions for use and safety information. It covers identification, product description, compatibility, maintenance, safety during use and risk mitigation, so the document can support safe handling and use of the product.
Clause 8 covers marking, labelling and packaging only when the standardization request asks for it. The guide says this clause should recommend marking, but it must not specify or recommend marks of conformity.
Annex ZA is the key link to CPR-2024. It must match the scope of the standard, list the relevant essential characteristics and show the assessment and verification systems and the clauses that support each declaration.
What terms does CEN/CLC Guide 36:2026 define?
- Candidate performance harmonized European Standard (candidate hEN) - a draft harmonized European Standard for construction products prepared in response to a standardization request under CPR-2024.
- Standardization request - the Commission request that defines the basis and limits for the candidate hEN.
- Essential characteristic - a product characteristic that must be assessed and declared in relation to the construction product's intended use.
- Product group - a set of products from the same manufacturer for which one assessment result can be used for the others for the characteristics concerned.
- Assessment and verification system (AVS) - the system that assigns assessment and verification tasks to the manufacturer and/or notified body.
- Factory production control (FPC) - the manufacturer's control system for equipment, raw materials, traceability, testing and surveillance of production.
- Declaration of performance and conformity (DoPC) - the manufacturer’s declaration used with Regulation (EU) 2024/3110 and linked to CE marking.
Who uses CEN/CLC Guide 36:2026?
CEN/CLC Guide 36:2026 is mainly used by Technical Committees drafting harmonized standards for construction products. It is also used by TC secretaries and drafting experts who prepare the text, the Annex ZA tables and the supporting justification.
Manufacturers use the guide indirectly because it shapes the standard they will use to draw up the DoPC, prepare product information and support CE marking. Notified bodies use it because it defines how assessment and verification tasks are structured under the applicable AVS.
It is relevant to the construction products sector, especially where the product standard must address performance characteristics, testing, environmental sustainability and documentation for regulated placement on the market.
What changed in CEN/CLC Guide 36:2026 from the previous edition?
CEN/CLC Guide 36:2026 supersedes CEN-CLC Guide 36:2024.
Which standards are used with CEN/CLC Guide 36:2026?
- CEN-CENELEC Internal Regulations - Part 3:2022 - the drafting framework used together with this guide for structure, wording, definitions, notes, clauses and annexes.
- EN 15804:2012+A2:2019 - the core rules for construction product environmental product declarations, used for the environmental sustainability parts of the guide and Annex ZA.
What does the CEN/CLC Guide 36:2026 document contain?
CEN/CLC Guide 36:2026 contains model clauses and drafting guidance for the cover page, title, contents, European foreword, scope, normative references, terms and definitions, characteristics, sampling methods, testing and assessment, assessment and verification, product information and safety information, and marking. It also gives the template and structure for Annex ZA, including the tables that link essential characteristics to clauses, reference documents, units, value kinds and assessment and verification systems.
The document also describes how to present performance in the standard, including values, classes, descriptions, thresholds and tabulated values. For Annex ZA, it provides the structure for the relationship with Regulation (EU) 2024/3110, the declaration of performance and conformity, and the interoperable human- and machine-readable data elements.
Relations
- Effective Date
- 28-Oct-2026
Frequently Asked Questions
CEN/CLC Guide 36:2026 is a guide published by the European Committee for Standardization (CEN). Its full title is "Guidance on the rules for the drafting and presentation of candidate performance harmonized standards in support of Regulation (EU) 2024/3110 Construction Products Regulation CPR-2024". This standard covers: This Guide outlines the rules for drafting and presenting candidate performance harmonized European Standards (hENs) for construction products under Regulation (EU) 2024/3110, known as the Construction Products Regulation CPR-2024. These standards are subject to a standardization request according to Article 5 of CPR-2024. This Guide gives rules which are additional to the CEN-CENELEC Internal Regulations (IR) - Part 3 (based on ISO/IEC Directives, Part 2) when this is necessary because of the special provisions of harmonized product standards in the construction sector. This Guide applies to all new candidate hENs and for new Work Items (WIs) revising/amending existing hENs included in a standardization request in support of CPR-2024. This guide does not include rules for candidate harmonized European Standards under Regulation (EU) No 305/2011 or for those harmonized European Standards within the framework of Regulation (EU) 2024/3110 that are subject to a standardization request according to Article 7 of this Regulation.
This Guide outlines the rules for drafting and presenting candidate performance harmonized European Standards (hENs) for construction products under Regulation (EU) 2024/3110, known as the Construction Products Regulation CPR-2024. These standards are subject to a standardization request according to Article 5 of CPR-2024. This Guide gives rules which are additional to the CEN-CENELEC Internal Regulations (IR) - Part 3 (based on ISO/IEC Directives, Part 2) when this is necessary because of the special provisions of harmonized product standards in the construction sector. This Guide applies to all new candidate hENs and for new Work Items (WIs) revising/amending existing hENs included in a standardization request in support of CPR-2024. This guide does not include rules for candidate harmonized European Standards under Regulation (EU) No 305/2011 or for those harmonized European Standards within the framework of Regulation (EU) 2024/3110 that are subject to a standardization request according to Article 7 of this Regulation.
CEN/CLC Guide 36:2026 has the following relationships with other standards: It is inter standard links to CEN/CLC Guide 36:2020. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
CEN/CLC Guide 36:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2027
Nadomešča:
SIST-V CEN/CLC Guide 36:2020
Napotki glede pravil za načrtovanje in predstavljanje kandidatov tehničnih
harmoniziranih standardov v podporo Uredbi (EU) 2024/3110 o gradbenih
proizvodih CPR-2024
Guidance on the rules for the drafting and presentation of candidate performance
harmonized standards in support of Regulation (EU) 2024/3110 Construction Products
Regulation CPR-2024
Ta slovenski standard je istoveten z: CEN/CLC Guide 36:2026
ICS:
01.120 Standardizacija. Splošna Standardization. General
pravila rules
91.010.01 Gradbeništvo na splošno Construction industry in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
CEN-CENELEC
GUIDE
Guidance on the rules for
the drafting and
presentation of candidate
performance harmonized
standards in support of
Regulation (EU) 2024/3110
Construction Products
Regulation CPR-2024
Edition 3, 2026-10
(Supersedes CEN-CLC Guide 36:2024)
CEN and CENELEC decided to adopt this new CEN-CENELEC Guide 36 through CEN BT decision
BT C129/2026 and CENELEC BT Decision D185/C008 respectively.
European Committee for Standardization
European Committee for Electrotechnical Standardization
Rue de la Science, 23
B - 1040 Brussels – Belgium
Tel: +32 2 550 08 11
Fax: +32 2 550 08 19
www.cencenelec.eu
CEN-CENELEC Guide 36:2026 (E)
Contents Page
European foreword _____________________________________________________________________ 5
Introduction ___________________________________________________________________________ 6
1 Scope _________________________________________________________________________ 7
2 Normative references _____________________________________________________________ 7
3 General principles ________________________________________________________________ 7
4 Format of a harmonized European Standard for construction products ______________________ 8
4.1 Cover page of the candidate hEN ___________________________________________________ 8
4.2 Element “Title” __________________________________________________________________ 8
4.3 Element “Contents” _______________________________________________________________ 8
4.4 Element “European foreword” ______________________________________________________ 9
4.5 Element “Introduction” ____________________________________________________________ 9
4.6 Clause 1 “Scope” ________________________________________________________________ 9
4.7 Clause 2 “Normative references” ____________________________________________________ 11
4.8 Clause 3 “Terms, definitions, symbols, units and abbreviated terms” ________________________ 11
4.9 Clause 4 “Characteristics” _________________________________________________________ 12
4.9.1 General ___________________________________________________________________ 12
4.9.2 Essential characteristics related to the constituents or components (if applicable) _________ 14
4.9.3 Structural and durability assessment if applicable __________________________________ 14
4.9.4 Fire related essential characteristics ____________________________________________ 16
4.9.5 Essential characteristics related to the release/emission of dangerous substances ________ 18
4.9.6 Essential characteristics related to environmental sustainability _______________________ 19
4.10 Clause 5 “Sampling methods, testing and assessment” __________________________________ 22
4.10.1 General ___________________________________________________________________ 22
4.10.2 Information to be provided for each assessment method ____________________________ 22
4.10.3 Release/emission of dangerous substances related essential characteristics ____________ 23
4.10.4 Environmental sustainability related essential characteristics _________________________ 24
4.10.5 Exceptions to the provision of assessment methods ________________________________ 26
4.11 Clause 6 “Assessment and verification” _______________________________________________ 28
4.11.1 General ___________________________________________________________________ 28
4.11.2 Introductory clause __________________________________________________________ 28
4.11.3 Assessment of performance __________________________________________________ 28
4.11.4 Verification of performance ___________________________________________________ 30
4.12 Clause 7 ‘Guidelines for the drawing up of general product information, instructions for use and safety
information’ ___________________________________________________________________________ 36
4.12.1 General ___________________________________________________________________ 36
4.12.2 General product information ___________________________________________________ 36
4.12.3 Instruction for use and safety information ________________________________________ 37
4.13 Clause 8 “Marking, labelling and packaging” ___________________________________________ 41
4.14 Normative annexes _______________________________________________________________ 41
5 Annex ZA (informative) ____________________________________________________________ 42
5.1 General ________________________________________________________________________ 42
5.2 Title ___________________________________________________________________________ 42
5.3 Scope and relevant characteristics __________________________________________________ 42
5.4 Performances in attached documentation of the product (when relevant) _____________________ 49
5.5 Assessment and verification systems ________________________________________________ 49
5.6 Guidelines to ensure interoperability of the human- and machine-readable formats ____________ 51
5.6.1 General ___________________________________________________________________ 51
CEN-CENELEC Guide 36:2026 (E)
5.6.2 Structured format used (schema) and data template ________________________________ 51
5.6.3 Declaration of performance and conformity _______________________________________ 51
5.6.3 General product information, instructions for use and safety information ________________ 57
5.7 Element “Bibliography” ____________________________________________________________ 58
CEN-CENELEC Guide 36:2026 (E)
European foreword
This document (CEN-CENELEC Guide 36:2026) has been prepared by CEN-CENELEC Coordination Group on
Construction and the built environment.
This document is intended for use by Technical Committees drafting candidate performance harmonized European
Standards for construction products and provides rules for the presentation of standards for construction products
drafted following a standardization request issued in the framework of Regulation (EU) 2024/3110 (CPR-2024) in
accordance with Article 5 of this Regulation.
This guide is not applicable to harmonized European Standards drafted following a standardization request issued
in accordance with Article 7 of CPR-2024.
Other EU Directives/Regulations may also apply to construction products, but this guide does not apply to them.
CEN-CENELEC Guide 36:2026 (E)
Introduction
CEN and CENELEC develop candidate performance harmonized European Standards for construction products
replying to European Commission standardization requests.
It has been considered necessary to propose guidance for the preparation, drafting and presentation of candidate
harmonized European Standards in support of the CPR.
Reference should also be made to the CEN and CENELEC Construction webpage, which lists many other guidance
documents relevant for the drafting work, accessible at:
https://www.cencenelec.eu/areas-of-work/cen-sectors/construction/
Other instructions and clarifications including a list of FAQs can be found on the European Commission website at:
http://ec.europa.eu/growth/sectors/construction/product-regulation_en
In the Clause 4 ‘Format of a harmonized European Standard for construction products’:
− Examples are provided in grey as good practice to follow:
EXAMPLE
− Examples to be avoided are given in red:
TO BE AVOIDED
− Model clauses text are presented in green and shall be used without modification in the harmonized
standard:
MODEL CLAUSE
− Text in [blue] represents items to be filled in or guidance on how to adapt model clauses.
− Template text for the Annex ZA is given in green and is to be used without modification in the
harmonized standard:
ANNEX ZA
CEN-CENELEC Guide 36:2026 (E)
1 Scope
This Guide outlines the rules for drafting and presenting candidate performance harmonized European Standards
(hENs) for construction products under Regulation (EU) 2024/3110, known as the Construction Products Regulation
CPR-2024. These standards are subject to a standardization request according to Article 5 of CPR-2024.
This Guide gives rules which are additional to the CEN-CENELEC Internal Regulations (IR) - Part 3 (based on
ISO/IEC Directives, Part 2) when this is necessary because of the special provisions of harmonized product standards
in the construction sector.
This Guide applies to all new candidate hENs and for new Work Items (WIs) revising/amending existing hENs
included in a standardization request in support of CPR-2024.
This guide does not include rules for candidate harmonized European Standards under Regulation (EU) No 305/2011
or for those harmonized European Standards within the framework of Regulation (EU) 2024/3110 that are subject to
a standardization request according to Article 7 of this Regulation.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references, the
latest edition of the referenced document (including any amendments) applies.
CEN-CENELEC Internal Regulations — Part 3:2022, Principles and rules for the structure and drafting of CEN
and CENELEC documents (ISO/IEC Directives — Part 2:2018, modified)
EN 15804:2012+A2:2019 , Sustainability of construction works — Environmental product declarations — Core
rules for the product category of construction products
3 General principles
This Guide gives the framework to be followed by Technical Committees (TCs) for drafting of a candidate hEN in the
framework of the Regulation (EU) 2024/3110 Construction Products Regulation (CPR-2024).
The basis for the development of candidate hEN is the standardization request.
Content not dealing with the implementation of the CPR-2024 shall not be included in a harmonized standard.
The candidate hEN for construction products should be coherent with the standardization request and only contain:
Products, materials, forms and intended uses as specified in the standardization request;
The essential characteristics covered in the standardization request;
The assessment methods, including test methods, calculation rules and tabulated values , to determine the
performance of the construction product in relation to these essential characteristics, as applicable;
Deemed to satisfy provisions established by delegated acts before the drafting of the standard (e.g.
reaction to fire) may be included. Deemed to satisfy provisions adopted after the publication of the standard
will apply directly without reference in the standard;
Additional provisions set out in relation to essential characteristics as indicated in the standardization
request or in applicable horizontal delegated acts:
o voluntary threshold levels: applicable only for products for certain declared uses;
o mandatory threshold level: applicable to the product independently of the declared uses;
o classes of performance;
o mandatory declaration.
Deviations from the proposed provisions in the standardization request should be avoided, however,
exceptionally they are possible, but only if properly justified and if agreed by Member States.
Technical details as regards the documentation provided together with the declaration of performance and
conformity;
1 As impacted by EN 15804:2012+A2:2019/AC:2021.
2 Tabulated values will be included in the delegated act covering classes, threshold and mandatory declaration
CEN-CENELEC Guide 36:2026 (E)
Technical details necessary for the implementation of the assessment and verification system including
determination of the product type, factory production control, validation of processes and data, and audits;
Guidelines for the drawing up of general product information, instructions for use and safety information;
Guidelines to ensure interoperability of the human- and machine-readable formats.
The following aspects shall not be included in hENs:
Non-applicable terminology from Construction Products Directive (CPD) and Construction Products
Regulation 2011 (CPR-2011) (e.g. evaluation of conformity, initial type testing, essential requirements,
attestation of conformity, declaration of conformity, declaration of performance, assessment and verification
of constancy of performance, etc.);
Reference to national regulations/requirements;
Expressions establishing obligations or requirements not included in the standardization request;
Installation, design, maintenance instructions and safety provisions except in the annex providing
guidelines for the drawing up of general product information, instructions for use and safety information;
Marking, labelling and packaging clause, unless already aligned with this Guide or included as presented in
this Guide
Notes containing product characteristics, requirements, permissions and recommendations. This kind of
information shall be included as a normal paragraph and part of the normative portion of the text, in
conformity with Clause 24 in the CEN-CENELEC IR - Part 3:2022, “Notes”.
CEN-CENELEC IR - Part 3:2022 shall be used in conjunction with this document when preparing a new candidate
hEN for construction products in support of CPR-2024, or when revising/amending an existing hEN as stated in the
scope of this document.
Moreover, following decision BT C089/2021 and D168/C108, when drafting hENs in support of EU legislation,
Technical Bodies shall check their compliance against a dedicated checklist (mandatory). The TC Secretary is
responsible for ensuring that the checklist is filled out and submitted to CCMC with the draft candidate hEN and their
supporting documents/justifications where relevant. In CEN, the matrix of responsibilities shall be followed.
List of guidance documents: https://www.cencenelec.eu/areas-of-work/cen-sectors/construction/
For each clause of the candidate hENs to be drafted, a number of examples regarding their content are given.
The common checklist for CPR is available here.
4 Format of a harmonized European Standard for construction products
4.1 Cover page of the candidate hEN
The cover page of a candidate hEN is prepared by CEN & CENELEC Management Centre (CCMC). However, each
concerned TC shall decide the title of the candidate hEN which shall be appropriate to its contents.
4.2 Element “Title”
The title page shall be prepared according to Clause 11 of CEN-CENELEC IR - Part 3:2022.
The proposed title should not be different from the one given in the standardization request by the European
Commission.
4.3 Element “Contents”
A table of contents is necessary to make the consultation of the hEN easier.
Clause 6 of CEN-CENELEC IR - Part 3:2022 provides guidance on the Organization and subdivision of the standard.
Terms in the “Terms and definitions” clause shall not be listed in the Contents.
The following lists provides the framework on which a candidate hEN for construction products should be based:
European foreword
Introduction
Scope
Normative references
CEN-CENELEC Guide 36:2026 (E)
Terms, definitions, symbols, units and abbreviated terms
Characteristics
Sampling methods, testing and assessment
Assessment and verification
Marking, labelling and packaging
Annex(es) (normative and/or informative), etc.
Annex ZA (exclusively for Regulation (EU) 2024/3110), Annex ZB, etc. (for other EU Legislation, if
any).
Bibliography
4.4 Element “European foreword”
The European foreword shall be prepared according to Clause 12 of CEN-CENELEC IR - Part 3:2022.
EXAMPLE
This document has been prepared by Technical Committee CEN/TC 72 “Fire detection and fire alarm systems”,
the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical text
or by endorsement, at the latest by February 2019, and conflicting national standards shall be withdrawn at the
latest by August 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.
CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 54-7:2000.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its Member
States.
For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this document.
The main changes with respect to the previous edition are listed below:
- applying the latest EN 50130-4:2011, EMC for immunity tests;
- introducing the open type smoke detector and related test methods;
- removing Annex N, additional provisions and test methods for smoke detectors with more than one smoke sensor.
Any feedback and questions on this document should be directed to the users’ national standards body. A complete
listing of these bodies can be found on the CEN [and/or CENELEC] website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia,
Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United Kingdom.
4.5 Element “Introduction”
The introduction, if needed, shall be prepared according to Clause 13 of CEN-CENELEC IR - Part 3:2022.
4.6 Clause 1 “Scope”
Following Clause 14 of CEN-CENELEC IR - Part 3:2022, this is required at the beginning of every candidate hEN to
define the subject of the standard and the aspect(s) covered in an unambiguous way and thereby to indicate the
limits of applicability of the standard or particular parts of it.
The scope shall be precise and state clearly which products, items, materials, forms, kits (as relevant) are covered,
for which intended uses, and which products are excluded. The scope shall be unambiguous, and any user shall be
able to know, without uncertainty, what is covered and what is not.
The scope shall be in line with the standardization request.
CEN-CENELEC Guide 36:2026 (E)
TO BE AVOIDED
This standard covers products intended generally for external use.
It is unclear if internal uses are covered.
This standard covers products used in construction.
Information provided is not detailed enough.
Standards shall be performance based and independent from the material and technologies used for the
manufacturing unless it is explicitly indicated in the standardization request. Materials shall only be mentioned in the
scope if included in the standardization request.
EXAMPLE
This standard covers precast concrete products manufactured using aggregates and precast lightweight concrete
products with closed structure.
The standardization request establishes the materials to be covered by the standard.
In general, and thereby in conformity with Clause 14 in CEN-CENELEC IR - Part 3:2022, the clause “Scope” shall
clearly identify the intended use of the construction product but shall not contain any normative instructions or
product characteristics.
The list of the intended use(s) of the product shall be included in the scope in a way as detailed as necessary to
ensure the link between the product its intended use and the relevant essential characteristics.
EXAMPLE
These pipes are intended to be used in underground unpressurized sewers.
TO BE AVOIDED
These plastic pipes may be used with metal pipes provided that appropriate joints are provided.
This information does not belong to the scope.
The scope should also, where appropriate, indicate in line with the standardization request:
Either the function and location within the works where the construction product is intended to be used (e.g.
internal walls, external walls) or should differentiate between different locations. The relevant construction
product characteristics may depend on the function and location in the works.
Whether recycled materials (other than closed-loop recycling during production) are either covered or
excluded, and appropriate provisions should then be included in the body of the standard if this is a
common practice in the market.
Whether reused products are covered or not by the standard.
NOTE Addressing products intended to be reused in harmonized standards require further clarifications and
guidance which will be provided in the future.
The key parts of the product as set out in the standardization request, if any. These key parts are required
to be covered by a harmonized technical specification under CPR-2024, either an existing harmonized
standard or another harmonized standard already included in the same standardization request.
When an hEN is revised, the scope cannot exclude any of the products previously covered, except in any
of the following situations:
They are covered by another harmonized standard to be progressed in parallel.
They are excluded by the applicable standardization request superseding a previous mandate or
standardization request.
CEN-CENELEC Guide 36:2026 (E)
4.7 Clause 2 “Normative references”
The normative references shall be prepared according to Clause 15 of CEN-CENELEC IR - Part 3:2022.
Standards and harmonized standards specifying product characteristics for a product shall not contain normative
references to quality management system requirements (e.g. EN ISO 9001, ISO 14000 or related series standards)
or certification provisions.
The normative references shall be dated in Clause 2 and in the normative text of the draft standard.
Normative references should be EN/ISO/IEC/ETSI standards. The use of non-EN/ISO/IEC standards can only be
included if included in the standardization request. In case, it is required but it was not included in the standardization
request, the European Commission needs to be consulted. In these cases, a request with appropriate justification
needs to be submitted to the EC via CCMC.
Normative references shall not be withdrawn standards at the time of publication of the hEN.
When the harmonized standard is published, it shall not include prENs/FprENs as normative references, i.e. all the
normative references shall be publicly available or be published at the same time as the harmonized standard.
Hence, it is recommended that a careful verification is done on the normative references in Clause 2 and text of the
standard to ensure that they are not withdrawn/outdated.
GOOD PRACTICE
Refer to a specific clause of the normative reference instead of referring to the whole document. If in this
specific clause of the normative reference there are no additional normative references, the normative
reference loop is closed.
4.8 Clause 3 “Terms, definitions, symbols, units and abbreviated terms”
As far as applicable, Clause 3 shall cover terms, definitions, symbols units and abbreviated terms and shall be in
accordance with CEN-CENELEC IR - Part 3:2022, Clauses 16 and 17 except for the possibility to include
requirements as supplementing information. Depending on the actual content of Clause 3, its title needs to be
adapted and subclauses shall be introduced.
Harmonized standards should contain the definitions used by the standards. If definitions are repeated, they should
be copied word by word from whichever document is considered the reference.
The terms and definitions from the CPR-2024 shall not be repeated in Clause 3 of the candidate hEN. When
necessary to use terms and definitions which have been defined in the CPR-2024, those terms and definitions shall
be used in the candidate hEN with the same meaning.
The following definition shall be added to keep consistency with Clause 6 “Assessment and verification”
MODEL CLAUSE
3.[x]
product group
set of products from the same manufacturer for which the assessment result of one product is valid for the other
products within the set, for the characteristic(s) concerned
Note 1 to entry: The grouping process avoids unnecessary testing when it is known, based on documented technical
justification, that one test result is representative for multiple products.
Note 2 to entry: A product group contains one or several product types. Products in a product group differ in some design
features or properties (e.g. edge detail, facings) but share those characteristics that allow the same assessment result to be
applied.
Note 3 to entry: Grouping combines different product types with identical performance for each characteristic.
The concept of product group is applicable to all essential characteristics including environmental sustainability
characteristics
Definitions shall, to the extent possible, not limit the application of the standard. In case there is a need to provide
definitions establishing limitations to the scope of the standard they should also be included in Clause 1 “Scope”.
CEN-CENELEC Guide 36:2026 (E)
Only definitions used later in the text need to be included. Definitions may be given:
in the form of one normative reference to another ISO, IEC, CEN or CENELEC standard dealing with
definitions, symbols and abbreviations relating to this field. If this option is used, the definitions in the
supporting standard shall fulfil the same conditions;
as a list of specialist terms included in the standard. This should make clear that the definitions are limited
to the use of the terms in the standard.
EXAMPLE
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
• ISO Online browsing platform: available at https://www.iso.org/obp
• IEC Electropedia: available at https://www.electropedia.org/
3.x
adhesion enhancer
additional coating on the load-bearing surface of the road stud or on the road surface which improves the
performance of the adhesive bond
All symbols or abbreviations used in the body of the candidate hEN shall be listed in this clause.
4.9 Clause 4 “Characteristics”
4.9.1 General
Only and all essential characteristics included in the standardization request shall be expressed in a normative way
in this clause.
The list of characteristics in the harmonized standard shall not contain any discrepancy with the list of essential
characteristics in the standardization request.
The harmonized standard shall not contain any additional characteristics to those included in the standardization
request.
While the standardization request refers to essential characteristics, the harmonized standard shall always refer to
characteristics. The concept of essential is implemented and described in Annex ZA.
Each product characteristic shall be the heading of the subclauses of Clause "Characteristics".
EXAMPLE
4.1 Compressive strength
…
4.x Thermal conductivity - testing
…
Construction product characteristics should be expressed, as far as possible, in terms of construction product
performance by:
describing the construction product expected behaviour;
describing the product behaviour to be assessed;
describing the way to express the performance as a level (value), class or description. Only classes
included in the standardization request or in applicable delegated acts shall be included unless properly
justified and if acceptable by Member States;
describing the unit in which the performance is expressed, when relevant;
CEN-CENELEC Guide 36:2026 (E)
describing the applicable thresholds and the conditions under which these thresholds apply, if any. Only
thresholds included in the standardization request or in applicable delegated acts shall be included unless
properly justified and if acceptable by Member States;
including the cross reference to the specific subclause of Clause 5 “Sampling methods, testing and
assessment” describing the test/assessment calculation method/deemed-to-satisfy provisions to be applied
for verifying the requested characteristic.
Below is presented model clauses for essential characteristic for each of the options to express performance, i.e.
level, class of performance and description.
MODEL CLAUSE Level (value)
4.x [Essential characteristic as indicated in the standardization request]
[Essential characteristic] indicates [description of the product behaviour and the technical basis for assessment
and declaration]. When assessed in accordance with the test method/assessment method/tabulated value [select
the applicable one] given in Clause 5.[x], relevant for the declared performance, the test result/assessment result/
tabulated values [select the applicable one] is expressed as a value in [units].
[If a threshold value applies] The performance shall be [describe the minimum/maximum, range applicable] for
products [describe the conditions to apply the threshold or refer to all products].
In case that several essential characteristics are assessed using the same assessment method and expressed in
the same units, these essential characteristics can be grouped and provided in a table in the same way it is
suggested for release of dangerous substances, see 4.9.5.
MODEL CLAUSE Class of performance
4.x [Essential characteristic as indicated in the standardization request]
[Essential characteristic] indicates [description of the product behaviour and the technical basis for assessment
and declaration]. When assessed in accordance with the test method/assessment method/tabulated value [select
the applicable one] given in Clause 5.[x], relevant for the declared performance, the test result/assessment
result/tabulated values [select the applicable one] is expressed as a class according to the classification in Table
[x].
Table x — [Essential characteristic] – classes
Declaration Performance in [units]
[Class] [Performance]
… …
[If a threshold value applies] The performance shall be [describe the minimum/maximum class, range of classes
applicable] for products [describe the conditions to apply the threshold or refer to all products].
MODEL CLAUSE Description
4.x [Essential characteristic as indicated in the standardization request]
[Essential characteristic] indicates [description of the product behaviour and the technical basis for assessment
and declaration]. When assessed in accordance with the test method/assessment method/tabulated value [select
the applicable one] given in Clause 5.[x], relevant for the declared performance, the test result/assessment
result/tabulated values [select the applicable one] is expressed as a description.
[If a threshold value applies] The performance shall be [describe the results of the assessment that are valid] for
products [describe the conditions to apply the threshold or refer to all products].
In case declaration without testing or declaration without further testing was possible under CPR-2011 or is under
development by the European Commission, a new delegated act will be adopted at the same time of citation of the
hEN.
Declaration without (further) testing include tabulated values provided in the standard. The tables will be also
included in the delegated act setting out classes, thresholds and mandatory declaration.
Model clause in case declaration without testing/declaration without further testing applies.
CEN-CENELEC Guide 36:2026 (E)
MODEL CLAUSE
4.x.1 Declaration without [further] testing [include “further” if included in the legal act]
Whether products covered by this standard meet the conditions [conditions or reference to them], they have
demonstrated the performance [performance], based on appropriate EN test methods, the assigned performance
applies to these products without requiring [further] testing [include “further” if included in the legal act].
4.x.1 Declaration based on tabulated values
Whether products covered by this standard meet the conditions [conditions or reference to them], the performance
is obtained from Table [x].
4.9.2 Essential characteristics related to the constituents or components (if applicable)
In some cases, a product's performance relates to the performance of its constituents or components used during
manufacturing. In such cases, the standardization request will include essential characteristics related to these
constituents. The harmonized standard should name the constituent within the characteristic's description.
If a constituent or component is supplied, the manufacturer can obtain performance details and documentation from
the supplier by using the 'cascading' provision under Article 59(1)(b) of Regulation (EU) 2024/3110. However, this
information should not be specified in the hEN, as the standard should not designate who carries out the tasks.
Even if the performance is obtained from the supplier, the complete assessment used shall be provided. In case the
performance is covered by another harmonized standard under CPR-2024 consistency with it should be checked in
the CPR data dictionary.
NOTE The European Commission is planning to implement the data dictionary for CPR-2024 when the first harmonized
standards will be made mandatory. If the data dictionary does not include this information, cross-check with the other standards
under CPR-2024 is recommended.
This clause may not be relevant for all construction product families so it shall be included only when the
standardization request includes essential characteristics related to constituents or components.
EXAMPLE
4.x Tensile yield strength - reinforcing steel
The tensile yield strength of the reinforced steel indicates the maximum stress that can be applied before
permanent shape change is achieved in ductile materials. When tested in accordance with the test method given
in Clause 5.x, relevant for the declared performance, the test result is expressed as a value in MPa.
4.9.3 Structural and durability assessment if applicable
4.9.3.1 General
The performance of the product as regards its capacity to deal with loads (structural behaviour) and its capacity to
maintain this performance over the time and under different environmental conditions (durability) may be expressed
in harmonized standards using different approaches. This clause is applicable only if it’s included in the SReq.
4.9.3.2 Essential characteristics
The standardization request will establish the list of essential characteristics dealing with structural behaviour and
durability. These characteristics related to them included in the harmonized standard shall refer to harmonized
European assessment methods and shall not refer to national implementation provisions.
Characteristics shall be based on
testing,
calculation aided by testing,
calculation using methods included in harmonized European Standards independent from any national
determined parameter, or
tabulated values included in harmonized European Standards independent from any national determined
parameter.
CEN-CENELEC Guide 36:2026 (E)
EXAMPLE
4.x Mechanical strength - testing - beams and blocks - blocks - punching-bending strength
The punching-bending strength indicates the failure load obtained in the punching-bending test. When assessed
in accordance with the test method given in Clause 5.x, relevant for the claimed class, the test result is expressed
as a class according to the classification in Table x.
Table x — Mechanical strength - testing - beams and blocks - blocks - punching-bending strength
classes
Minimum characteristic resistance to concentrated loads
Declaration
kN
Very low non-resisting (VLNR) 0,7
low non-resisting (LNR) 1,0
Non-resisting (NR) 1,5
Semi-resisting (SR) 2,0
Resisting (RR) 2,5
4.9.3.3 Declaration in attached documentation of the product
When it is not possible or when the applicable essential characteristics may require to be complemented by additional
rules, the structural behaviour, fatigue resistance, earthquake resistance, explosion resistance, fire resistance and
durability may be assessed using calculation rules or tabulated values defined at national level such as the national
implementation provisions to the Eurocodes. These rules are related to the behaviour of the product under certain
conditions and therefore cannot be included in the declaration of performance and conformity or referred to in the
harmonized standard but the calculation, the results and the reference to calculation methods or tabulated values
used shall be provided together with the declaration of performance and conformity.
This clause may not be relevant for all construction product families. The following model clause shall be included
only when the standardization request includes the need to provide documents in attachment to the declaration of
performance including set of drawings and calculations. This clause should be the last in Clause 4 “Characteristics”.
The term custom-made products is defined in the CPR-2024, all products that are not custom-made are considered
off-the-shelf including one-off products.
MODEL CLAUSE
4.x Performances in attached documentation of the product
4.x.1 General
In case the performance specified for the product in terms of structural behaviour, including fatigue resistance,
earthquake resistance, explosion resistance, fire resistance and durability, [remove those which are never
applicable] is expressed by referring to the respective production documentation or structural design calculations
in a way not directly related to essential characteristics, the following applies
4.x.2 Off-the-shelf products
In case of off-the-shelf products, information about the loads and exposure scenarios of product is not known so
the relevant information comprises:
[Include as specified in the standardization request.]
[Add item(s) as required by the standardization request.]
4.x.3 Custom-made products
In case of custom-made products, information about the loads and exposure scenarios of the product is available
so the relevant information comprises:
[Include as specified in the standardization request.]
[Add item(s) as required by the standardization request.]
CEN-CENELEC Guide 36:2026 (E)
EXAMPLE
4.x Performances in attached documentation of the product
4.x.1 General
In case the performance specified for the product in terms of structural behaviour, including fatigue resistance,
earthquake resistance, explosion resistance, fire resistance and durability, is expressed by referring to the
respective production documentation or structural design calculations in a way not directly related to essential
characteristics, the following applies
4.x.2 Off-the-shelf products
In case of off-the-shelf products, information about the loads and exposure scenarios of product is not known so
the relevant information comprises:
a detailed set of drawings including nominal dimensions, tolerances and materials used allow the
determination of the behaviour when the loads and exposure scenarios are defined;
usual load and exposure scenarios and calculations or tabulated values relevant to them, including
durability assessment, even if they do not reflect the applicable loads and exposures in which the product
is used;
reference to the calculation methods, exposure scenarios and any relevant additional information.
4.x.3 Custom-made products
In case of custom-made products, information about the loads and exposure scenarios of the product is available
so the relevant information comprises:
a detailed set of drawings including nominal dimensions, tolerances and materials used allow the
calculation of the behaviour for the established loads and exposure scenarios;
the applicable load and exposure scenarios and calculations or tabulated values relevant to them,
including durability assessment;
reference to the calculation methods, description of the exposure scenarios and any relevant additional
information.
4.9.4 Fire related essential characteristics
4.9.4.1 General
In case essential characteristics related to fire performance are included in the standardization request, the
following rules apply.
Characteristics related to fire can be grouped in a subclause of Clause 4.
4.9.4.2 Reaction to fire
Model clause to define the characteristic reaction to fire, if applicable.
MODEL CLAUSE
4.x Reaction to fire
The reaction to fire indicates the response of the [name of the products as they appear in the title of the standard]
in contributing by its own decomposition to a fire to which it is exposed, under specified conditions. When tested
in accordance with the test method given in Clause 5.[x], relevant for the claimed class, the test results are
expressed as a class according to the classification published in the Official Journal of the European Union on this
specific matter.
NOTE The applicable document at the time this standard was drafted is Commission Delegated Regulation (EU) 2026/331 of 13 February
2026 https://eur-lex.europa.eu/eli/reg_del/2026/331/oj/eng
A classification without testing for the reaction to fire of certain materials is being developed, all products made only
of these materials can apply declaration without testing in accordance with this delegated act.
In case classification without testing or classification without further testing were possible under CPR-2011 and in
case a new provision in this regard was already discussed with the European Commission, a delegated act setting
out the rules will be adopted at the same time of citation of the hEN.
CEN-CENELEC Guide 36:2026 (E)
The technical content shall be included in the text of the standard and will be included also in the relevant
delegated act.
Model clause in case classification without testing.
MODEL CLAUSE
4.x.1 Classification without [further] testing [include “further” if included in the legal act]
Where products covered by this standard meet the conditions [conditions or reference to
...



