EN ISO 11998:2026
(Main)Paints and varnishes - Determination of wet-scrub resistance of coatings (ISO 11998:2026)
- Abstract
This document specifies an accelerated method for the determination of wet-scrub resistance. The determination of cleanability is not covered in the scope of this document.
NOTE The ability of coatings to withstand wear caused by repeated cleaning operations is an important consideration both from a practical point of view and when comparing and rating such coatings. Since wet-scrub resistance depends not only on the quality of a coating but also on the substrate, the method of application, the drying conditions and other factors, the results obtained are not directly transferable to actual practice. In this document, the evaluation of the coating is based on a defined substrate, a fixed application method, specified drying conditions and a defined method of wet scrubbing.
- Status
- Published
- Publication Date
- 20-Oct-2026
- Technical Committee
- CEN/TC 139 - Paints and varnishes
- Drafting Committee
- CEN/TC 139 - Paints and varnishes
- Current Stage
- 6060 - Definitive text made available (DAV) - Publishing
- Start Date
- 21-Oct-2026
- Completion Date
- 21-Oct-2026
EN ISO 11998:2026 is a CEN standard, aligned with ISO 11998, for an accelerated test of the wet-scrub resistance of coatings. It tells laboratories how to prepare coated test panels, expose them to repeated wet scrubbing under defined conditions, and calculate resistance from mass loss and film-thickness loss. The document is for comparing coatings under controlled conditions, not for judging cleanability in use.
What does EN ISO 11998:2026 specify?
EN ISO 11998:2026 specifies a defined method for measuring wet-scrub resistance and excludes cleanability from its scope. The method uses a fixed substrate, application method, drying conditions and wet-scrubbing procedure so that results can be compared between coatings and laboratories.
The document is organized into 11 clauses and 6 annexes. Clauses 1 to 11 cover scope, references, terms, principle, reagents, apparatus, sampling, procedure, result calculation, precision and the test report. Annexes A to D are normative and Annexes E and F are informative.
| Annex | What it covers |
|---|---|
| Annex A | Determination of dry-film density of the coating |
| Annex B | Quality control of the non-woven abrasive |
| Annex C | Acceptance of new non-woven abrasive |
| Annex D | Preparation and formulation of reference paint |
| Annex E | Example of reference paint |
| Annex F | Details on interlaboratory comparison |
What are the key requirements of EN ISO 11998:2026?
EN ISO 11998:2026 requires a controlled workflow from sample preparation to result calculation. The main point in practice is that the coating, the substrate, the abrasive pad, the washing liquid and the test conditions all have to be kept within the defined setup, otherwise the result is not comparable.
Test principle and purpose
Clause 4 states that the coating is applied to a test panel, dried and conditioned, weighed, and then exposed to a defined number of wet-scrub cycles in a scrub testing machine. The panel is washed, dried and weighed again, and the change in mass is used to calculate mean loss in film thickness. In practice, this gives a single numerical basis for rating the coating against an agreed reference value or class.
Reagents and consumables
Clause 5 specifies the washing liquid as a sodium n-dodecylbenzenesulfonate solution in grade 3 water. Clause 6 also requires a new technical non-woven abrasive for every test, with batch control and acceptance controlled by Annexes B and C. In practice, the scrub pad is not just a consumable - its quality directly affects the result, so laboratories need a documented pad control system.
Apparatus and test setup
Clause 6 defines the test panel, film applicator, wet-scrub tester, scrub pad holder, analytical balance and ruler. The scrub tester is a reciprocating machine with a specified stroke length and cycle rate, and the pad holder has a defined downward force. In practice, the equipment setup is part of the test method, not just a laboratory choice.
Sampling, film application and drying
Clause 7 requires representative sampling according to ISO 15528 and preparation according to ISO 1513. Clause 8 requires a draw-down that is long enough for the scrub length, and enough coated material for threefold testing. The coated panels are dried at the stated temperature and humidity for the drying period agreed by the customer or by the relevant classification or legislation, and that drying time must be recorded. In practice, the drying history is part of the result because it affects the coating response.
Scrubbing and post-test handling
Clause 8 requires the washing liquid to be applied to the coating, left in contact for 60 s, and then the abrasive pad to be saturated to the specified mass before the machine is run for the set number of cycles. After testing, the panel is rinsed, dried to constant mass and the scrub trace is measured. In practice, this means the laboratory has to control both the wetting step and the recovery step before weighing.
Result calculation and assessment
Clause 9 gives the calculations for scrubbed area, loss in coating mass per unit area and mean loss in dry-film thickness. The dry-film density needed for that calculation is determined using Annex A. In practice, the reported value is the mean loss in micrometres, which can then be used for classification where a class system applies.
Precision and reporting
Clause 10 reports precision data from an interlaboratory study on the reference paint with two abrasive pad batches, including repeatability and reproducibility information. Clause 11 requires the report to identify the product, the document reference, drying conditions, dry-film density, abrasive identification, results, laboratory details, deviations, anomalies and the test date. In practice, the report has to be complete enough that another laboratory can understand exactly how the result was obtained.
What terms does EN ISO 11998:2026 define?
EN ISO 11998:2026 defines a small set of terms that control how the test is run and how the result is interpreted.
- Scrub cycle - one reciprocal movement of the scrub pad over the scrub length in both directions.
- Scrub length - the stroke length plus the length of the pad.
- Stroke length - the distance traversed by one stroke of the apparatus.
- Wet-scrub resistance - the ability of a dry coating film to keep its loss in film thickness below a specified value over a defined area after a defined number of wet-scrub cycles.
- Dry-film density - the density used to convert mass loss into film-thickness loss in Annex A.
- Technical non-woven abrasive - the abrasive pad used on the scrub holder during the test.
- Reference paint - the specified coating used to check pad quality and compare performance in the annexes.
Who uses EN ISO 11998:2026?
EN ISO 11998:2026 is used by paint and varnish laboratories, coating manufacturers, quality-control teams and test laboratories that compare wet-scrub performance. It is also relevant to product development groups that need to compare formulations under the same test conditions.
Buyers, specifiers and classification users use the result when they need a repeatable way to compare coatings for wear from repeated cleaning or washing. The note in the document also shows that classification standards such as EN 13300 may use the result for rating purposes.
What changed in EN ISO 11998:2026 from the previous edition?
EN ISO 11998:2026 replaces the second edition, ISO 11998:2006, and the foreword says it was technically revised. The changes stated in the document are:
- the title has been changed;
- cleanability has been deleted completely;
- the abrasive pad has been changed;
- the statistical data on reproducibility and repeatability have been updated.
Which standards are used with EN ISO 11998:2026?
EN ISO 11998:2026 refers to several standards that support sampling, conditioning, vocabulary and statistics:
- ISO 1513 - examination and preparation of test samples.
- ISO 1524 - determination of fineness of grind; used in Annex D when preparing the reference paint.
- ISO 3270 - temperatures and humidities for conditioning and testing; supports controlled test conditions.
- ISO 3696 - water for analytical laboratory use; defines the water quality used for the washing liquid.
- ISO 4618 - vocabulary for paints and varnishes; provides the terms used in Clause 3.
- ISO 5725-2 - repeatability and reproducibility statistics; used for the precision work in Annex C and the interlaboratory study.
- ISO 15528 - sampling of paints, varnishes and raw materials; used in Clause 7.
EN 13300 is also named in the document as a classification standard that can use the wet-scrub result.
What does the EN ISO 11998:2026 document contain?
EN ISO 11998:2026 contains the test principle, the equipment setup, the sampling and procedure steps, the calculation formulas and the reporting items needed for a wet-scrub resistance test. It also includes figures showing the scrub pad holder, the clamping arrangement and the test-piece locations, which help laboratories set up the apparatus correctly.
The annexes add the supporting methods that make the test reproducible. Annex A gives the dry-film density method, Annexes B and C control the abrasive pad, and Annex D gives the reference paint preparation and formulation. Annex E gives an example reference paint, and Annex F summarizes the interlaboratory comparison used for precision data.
Relations
- Effective Date
- 12-Jun-2024
- Effective Date
- 04-Nov-2026
- Effective Date
- 04-Nov-2026
- Effective Date
- 04-Nov-2026
- Effective Date
- 04-Nov-2026
- Effective Date
- 04-Nov-2026
- Referred By
EN 16301:2021 - Natural stone test methods - Determination of sensitivity to accidental staining - Effective Date
- 28-Oct-2026
- Effective Date
- 28-Oct-2026
- Referred By
EN 16301:2013 - Natural stone test methods - Determination of sensitivity to accidental staining - Effective Date
- 28-Oct-2026
- Effective Date
- 28-Oct-2026
- Consolidated By
ISO 11998:2026 - Paints and varnishes — Determination of wet-scrub resistance of coatings - Effective Date
- 12-Feb-2026
Frequently Asked Questions
EN ISO 11998:2026 is a standard published by the European Committee for Standardization (CEN). Its full title is "Paints and varnishes - Determination of wet-scrub resistance of coatings (ISO 11998:2026)". This standard covers: This document specifies an accelerated method for the determination of wet-scrub resistance. The determination of cleanability is not covered in the scope of this document. NOTE The ability of coatings to withstand wear caused by repeated cleaning operations is an important consideration both from a practical point of view and when comparing and rating such coatings. Since wet-scrub resistance depends not only on the quality of a coating but also on the substrate, the method of application, the drying conditions and other factors, the results obtained are not directly transferable to actual practice. In this document, the evaluation of the coating is based on a defined substrate, a fixed application method, specified drying conditions and a defined method of wet scrubbing.
This document specifies an accelerated method for the determination of wet-scrub resistance. The determination of cleanability is not covered in the scope of this document. NOTE The ability of coatings to withstand wear caused by repeated cleaning operations is an important consideration both from a practical point of view and when comparing and rating such coatings. Since wet-scrub resistance depends not only on the quality of a coating but also on the substrate, the method of application, the drying conditions and other factors, the results obtained are not directly transferable to actual practice. In this document, the evaluation of the coating is based on a defined substrate, a fixed application method, specified drying conditions and a defined method of wet scrubbing.
EN ISO 11998:2026 is classified under the following ICS (International Classification for Standards) categories: 87.040 - Paints and varnishes. The ICS classification helps identify the subject area and facilitates finding related standards.
EN ISO 11998:2026 has the following relationships with other standards: It is inter standard links to EN ISO 11998:2006, ISO 15528:2020, ISO 1513:2010, ISO 4618:2023, ISO 3696:1987, ISO 5725-2:2025, EN 16301:2021, EN 16566:2014, EN 16301:2013, EN 13300:2022, ISO 11998:2026. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN ISO 11998:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2026
Nadomešča:
SIST EN ISO 11998:2006
Barve in laki - Določanje odpornosti proti mokremu drgnjenju premazov (ISO
11998:2026)
Paints and varnishes - Determination of wet-scrub resistance of coatings (ISO
11998:2026)
Beschichtungsstoffe - Bestimmung der Nassabriebbeständigkeit von Beschichtungen
(ISO 11998:2026)
Peintures et vernis - Détermination de la résistance au frottement humide des
revêtements (ISO 11998:2026)
Ta slovenski standard je istoveten z: EN ISO 11998:2026
ICS:
87.040 Barve in laki Paints and varnishes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 11998
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2026
EUROPÄISCHE NORM
ICS 87.040 Supersedes EN ISO 11998:2006
English Version
Paints and varnishes - Determination of wet-scrub
resistance of coatings (ISO 11998:2026)
Peintures et vernis - Détermination de la résistance au Beschichtungsstoffe - Bestimmung der
frottement humide des revêtements (ISO 11998:2026) Nassabriebbeständigkeit von Beschichtungen (ISO
11998:2026)
This European Standard was approved by CEN on 3 October 2026.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11998:2026 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 11998:2026) has been prepared by Technical Committee ISO/TC 35 "Paints and
varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2027, and conflicting national standards shall be
withdrawn at the latest by April 2027.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11998:2006.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 11998:2026 has been approved by CEN as EN ISO 11998:2026 without any modification.
International
Standard
ISO 11998
Third edition
Paints and varnishes —
2026-10
Determination of wet-scrub
resistance of coatings
Peintures et vernis — Détermination de la résistance au
frottement humide des revêtements
Reference number
ISO 11998:2026(en) © ISO 2026
ISO 11998:2026(en)
© ISO 2026
All rights reserved.
This ISO publication is protected by copyright and is owned by ISO and/or its licensors.
The content of this ISO publication is provided under licence, not sold. Use is subject to the applicable licence terms issued by ISO,
an ISO member body, or an authorized third-party distributor.
Except as required for implementation or expressly permitted by a separate licence, no part of this ISO publication may be
reproduced, distributed, modified, used, or made available in any form or by any means – electronic or mechanical, including
photocopying, scanning, recording, or posting on internal or external digital platforms.
Any use beyond the scope of the granted rights is prohibited and may result in legal action.
ISO copyright office
CP 401 • CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 11998:2026(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Reagents . 2
6 Apparatus . 2
7 Sampling . 4
8 Procedure . 4
8.1 Film application .4
8.2 Wet-scrub resistance .4
9 Expression of results . 6
9.1 Calculation of the loss in coating mass per unit area .6
9.1.1 Area traversed by the scrub pad .6
9.1.2 Loss in coating mass per unit area .6
9.2 Calculation of mean loss in film thickness .6
9.3 Assessment of wet-scrub resistance .7
10 Precision . 7
10.1 General .7
10.2 Repeatability .7
10.3 Reproducibility . .7
11 Test report . 7
Annex A (normative) Determination of dry-film density of the coating . 8
Annex B (normative) Quality control of the non-woven abrasive .10
Annex C (normative) Acceptance of new non-woven abrasive .11
Annex D (normative) Preparation and formulation of reference paint .12
Annex E (informative) Example of reference paint . 14
Annex F (informative) Details on interlaboratory comparison .16
Bibliography . 17
iii
ISO 11998:2026(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee
SC 9, General test methods for paints and varnishes, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 139, Paints and varnishes, in accordance with the
Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 11998:2006), which has been technically
revised.
The main changes are as follows:
— the title has been changed to “Determination of wet-scrub resistance of coatings”;
— the introduction has been deleted;
— cleanability has been deleted completely;
— weighing accuracy has been changed from 1 mg to 0,1 mg;
— the description of the abrasive pad has been clarified;
— five new Annexes B to F have been added;
— a batch control of the non-woven abrasive has been introduced in Annex B;
— criteria for the acceptance of new non-woven abrasive have been introduced in Annex C;
— preparation and formulation of a general reference paint have been introduced in Annex D;
— preparation and formulation of an example reference paint have been introduced in Annex E;
— details on the interlaboratory comparison have been introduced in Annex F;
— the statistical data on reproducibility and repeatability have been updated.
iv
ISO 11998:2026(en)
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
v
International Standard ISO 11998:2026(en)
Paints and varnishes — Determination of wet-scrub
resistance of coatings
1 Scope
This document specifies an accelerated method for the determination of wet-scrub resistance. The
determination of cleanability is not covered in the scope of this document.
NOTE The ability of coatings to withstand wear caused by repeated cleaning operations is an important
consideration both from a practical point of view and when comparing and rating such coatings. Since wet-scrub
resistance depends not only on the quality of a coating but also on the substrate, the method of application, the drying
conditions and other factors, the results obtained are not directly transferable to actual practice. In this document,
the evaluation of the coating is based on a defined substrate, a fixed application method, specified drying conditions
and a defined method of wet scrubbing.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 1513, Paints and varnishes — Examination and preparation of test samples
ISO 3696, Water for analytical laboratory use — Specification and test methods
ISO 4618, Paints and varnishes — Vocabulary
ISO 5725-2, Accuracy (trueness and precision) of measurement methods and results — Part 2: Basic method for
the determination of repeatability and reproducibility of a standard measurement method
ISO 15528, Paints, varnishes and raw materials for paints and varnishes — Sampling
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 4618 and the following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
scrub cycle
one reciprocal movement of the scrub pad over the scrub length (3.2) in both directions
3.2
scrub length
stroke length (3.3) plus the length of the pad
3.3
stroke length
distance traversed by one stroke of the apparatus
ISO 11998:2026(en)
3.4
wet-scrub resistance
ability of a dry coating film to sustain less than a specified loss in film thickness, averaged over a defined
area, when exposed to a defined number of wet-scrub cycles
4 Principle
The test coating is applied to a test panel using a film applicator at the appropriate gap clearance. After
drying and conditioning, the coated panel is weighed and subjected to a defined number of wet-scrub cycles
in a scrub testing machine as described in 8.2.
NOTE Some classification standards, e.g. EN 13300, require fewer scrub cycles.
It is then washed, dried and weighed again to determine its loss in mass, from which the mean loss in film
thickness is calculated.
Through comparison of the mean loss in film thickness with a specified value, as agreed between interested
parties, the coating can be rated in wet-scrub resistance classes.
5 Reagents
5.1 Washing liquid. Use a 2,5 g/l solution of sodium n-dodecylbenzenesulfonate (CAS Registry Number
®1)
25155-30-0) in water conforming to the requirements of grade 3 of ISO 3696. Allow the solution to stand
before use until all air-bubbles and foam have dissipated.
6 Apparatus
6.1 Test panel, made of polyvinyl chloride (PVC) film free of migration-susceptible chemical plasticizers,
of sufficient rigidity to ensure a flat surface, impervious to and unaffected by water or aliphatic organic
solvents and of a nominal thickness of 0,25 mm, approximately 430 mm long and not less than 80 mm wide.
Other types of film may be used where the coating contains solvent, which can adversely affect the PVC film,
e.g. a metal alloy with a thickness of about 0,25 mm. If the coating delaminates before or during the test,
another more suitable substrate shall be used.
6.2 Film applicator, preferably an automatic film applicator, used at an application speed of 10 mm/s to
15 mm/s and fitted with a doctor blade with an appropriate gap clearance and a gap width of at least 60 mm.
6.3 Wet-scrub tester apparatus, consisting of a reciprocating scrub testing machine with a stroke length
of (300 ± 10) mm and operating at approximately (37 ± 2) scrub cycles per minute. A counter for recording
the number of scrub cycles shall be provided.
6.4 Scrub pad holder, consisting of a metal plate fitted with pins to hold the abrasive pad. A mounting
device with elongated holes is loosely fitted on the top of the plate (see Figure 1 and Figure 2). Alternatively,
other scrub pad holders, e.g. with hook-and-loop fastener, can be used. The mass of the scrub pad holder,
which exerts a downward force on the test panel shall be (135 ± 1) g.
1) CAS Registry Number® is a trademark of the American Chemical Society (ACS). This information is given for the
convenience of users of this document and does not constitute an endorsement by ISO of the product named. Equivalent
products may be used if they can be shown to lead to the same results.
ISO 11998:2026(en)
Figure 1 — Mounting device
Dimensions in millimetres
Key
1 pins
Figure 2 — Scrub pad holder
6.5 Technical non-woven abrasive, a non-woven pad, consisting of a plastics material, with embedded
abrasive, measuring (90,0 ± 0,5) mm × (39,0 ± 0,5) mm. A new abrasive pad shall be used for every test.
2) 3)
TM TM
NOTE Scotch-Brite 7448+ Vlies and Abraflex E-Type S-1200 Vlies have proven to be suitable.
Since the quality of the technical non-woven abrasive has a direct impact on the test result, batch control of
suitable technical non-woven pads is required. The quality of each batch shall be proven in accordance with
Annex B.
2) Scotch-Brite 7448+ Vlies is the trade name of a product supplied by 3M. This information is given for the convenience
of users of this document and does not constitute an endorsement by ISO of the product named. Equivalent products may
be used if they can be shown to lead to the same results.
3) Abraflex E-Type S-1200 Vlies is the trade name of a product supplied by JÖST abrasives GmbH. This information is
given for the convenience of users of this document and does not constitute an endorsement by ISO of the product named.
Equivalent products may be used if they can be shown to lead to the same results.
--------
...



