M/601 - PED 2

This document specifies requirements for qualification of welding operators and weld setters for mechanized and automatic welding of metallic materials.
This document does not apply to personnel who:
—     do not control or adjust welding parameters;
—     are not involved in the setup of welding equipment.
Qualification of welding operators and weld setters for friction stir welding and friction stir spot welding are covered by ISO 25239-3 and ISO 18785-3, respectively.

This document specifies the technical delivery requirements for seamless and welded butt-welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austenitic and austenitic-ferritic (duplex) stainless steel in two test-categories which are intended for pressure purposes at room temperature, at low temperature or at elevated temperatures, and for the transmission and distribution of fluids and gases.
It specifies:
a)   type of fittings;
1)   type A: butt-welding fittings with reduced pressure factor;
2)   type B: butt-welding fittings for use at full service pressure;
b)   steel grades and their chemical compositions;
c)   mechanical properties;
d)   dimensions and tolerances;
e)   requirements for inspection and testing;
f)   inspection documents;
g)   marking;
h)   protection and packaging.
NOTE   The selection of the appropriate fitting (material, thickness) is the ultimate responsibility of the manufacturer of the pressure equipment (see European Legislation for Pressure Equipment). In the case of a harmonized supporting standard for materials, presumption of conformity to the ESRs is limited to technical data of materials in the standard and does not presume adequacy of the material to a specific item of equipment. Consequently, it is essential that the technical data stated in the material standard be assessed against the design requirements of this specific item of equipment to verify that the ESRs of the PED are satisfied.

This document specifies requirements for qualification of welding operators and weld setters for mechanized and automatic welding of metallic materials.
This document does not apply to personnel who:
—     do not control or adjust welding parameters;
—     are not involved in the setup of welding equipment.
Qualification of welding operators and weld setters for friction stir welding and friction stir spot welding are covered by ISO 25239-3 and ISO 18785-3, respectively.

The existing Annex ZB is still incorrectly referring to the old 97/23/EC Directive. Reference should be made to Directive 2014/68/EU for pressure equipment. To be done via this WI.

The existing Annex ZB is still incorrectly referring to the old 97/23/EC Directive. Reference should be made to Directive 2014/68/EU for pressure equipment. To be done via this WI.

This document specifies the requirements for the design, manufacture and testing of cylinders, tubes and other pressure vessels of steel, stainless steel, aluminium alloys or of non-metallic construction material. These are intended for the stationary storage of gaseous hydrogen of up to a maximum water capacity of 10 000 l and a maximum allowable working pressure not exceeding 1 100 bar, of seamless metallic construction (Type 1) or of composite construction (Types 2, 3 and 4), hereafter referred to as pressure vessels.
NOTE   Additional requirements with regard to assemblies (manifolded cylinders and tubes and other pressure vessels) are not covered by this document.
This document is not applicable to Type 2 and 3 vessels with welded liners.
This document is not applicable to pressure vessels used for solid, liquid hydrogen or hybrid cryogenic-high pressure hydrogen storage applications.
This document is not applicable to external piping which can be designed according to recognized standards.

This document is applicable to metallic valves as pressure accessories for industrial applications with a maximum allowable pressure PS greater than 0,5 bar in accordance with the European legislation for pressure equipment and specifies requirements applicable to design, manufacture, testing, materials and documentation.
All essential safety requirements of the European legislation for pressure equipment applicable to valves have been taken into consideration and are addressed in this document.
This document does not apply to:
-   safety valve and bursting disc (safety accessories),
-   sight glass with its frames (component of a pressure equipment), and
-   measurement chambers.
For other exclusions, refer to the European legislation for pressure equipment [60].

This document is applicable to metallic valves as pressure accessories for industrial applications with a maximum allowable pressure PS greater than 0,5 bar in accordance with the European legislation for pressure equipment and specifies requirements applicable to design, manufacture, testing, materials and documentation.
All essential safety requirements of the European legislation for pressure equipment applicable to valves have been taken into consideration and are addressed in this document.
This document does not apply to:
-   safety valve and bursting disc (safety accessories),
-   sight glass with its frames (component of a pressure equipment), and
-   measurement chambers.
For other exclusions, refer to the European legislation for pressure equipment [60].

This document specifies requirements for limiters which are incorporated into safety systems for shell boilers as specified in EN 12953 1:2012.
The design requirements and examination of the limiters are covered in this document.
NOTE   See Annex E for determination of the characteristic data for use in protective circuits with a safety integrity level (SIL) rating. The requirements for limiters with regard to the safety integrity level (SIL), for example, in accordance with EN 61508 are not covered in this document.

This European Standard specifies the requirements for the design and testing of spring loaded pressure relief valves and thermal expansion valves for use in:
- static LPG pressure vessels,
NOTE   The pressure vessels can be situated above ground, underground or mounded.
- transportable LPG welded steel pressure drums,
- LPG pressure vessels on road tankers, rail tankers, tank-containers or demountable tanks.
This document does not address relief valves for LPG cylinders, which are identified in EN 13953.
This document does not address production testing.
Normative Annex B prescribes testing with conditioning at - 40 °C for valves for use under extreme low temperature conditions.
The requirements for pressure relief valve accessories such as isolating devices, changeover manifolds and vent pipes are specified in EN 14071.
EN 14570 identifies the requirements for the pressure relief valve capacities for static pressure vessels.
EN 12252 identifies the requirements for the pressure relief valve capacities for road tankers.
Valves designed in accordance with this standard are specifically for use in LPG applications. Valves manufactured in accordance with EN ISO 4126 1 may also be used in certain LPG applications.
Terms used with LPG pressure relief valves are described graphically in Annex A.

This document specifies the design, testing and inspection requirements for pressure relief valve isolating devices, valve manifolds, vent pipes and system assemblies which are, where necessary, used with pressure relief valves for use in static pressure vessels for Liquefied Petroleum Gas (LPG) service.
This document addresses both prototype testing and production testing of isolating devices and PRV manifolds.
Pressure relief valves for LPG pressure vessels are specified in EN 14129:2014.

This document specifies the minimum requirements for safety related equipment for shell boilers (generator and/or assemblies) as specified in EN 12953-1:2012, to ensure the boiler operates within the allowable limits (pressure, temperature, etc.) and if the limits are exceeded the energy supply is automatically interrupted and locked out, irrespective of the degree of intervention.
NOTE 1    For this document, the term “boiler” is applicable for generator and/or assemblies.
NOTE 2   The maximum time of operation without manual (human) intervention can be specified for each boiler system.
NOTE 3   Annex C gives recommendations of operation and testing of the boiler system with a maximum time of operation without manual (human) intervention of 24 h and 72 h.

This document describes the calculation of:
—     mass flow for sizing pressure relief devices for parts of refrigerating systems;
—     discharge capacities for pressure relief valves and other pressure relief devices in refrigerating systems including the necessary data for sizing these when relieving to atmosphere or to part of the refrigerating system at lower pressure;
—     the pressure loss in the inlet and outlet lines of pressure relief valves and other pressure relief devices and includes the necessary data.
This document specifies the requirements for selection of pressure relief devices to prevent excessive pressure due to internal and external heat sources, the sources of increasing pressure (e.g. compressor, heaters, etc.) and thermal expansion of trapped liquid.
NOTE            The term "refrigerating system" used in this document includes heat pumps.

This European Standard specifies constructional, functional, testing, marking, sizing and documentation requirements of gas pressure regulators:
-   for inlet pressures up to 100 bar and nominal diameters up to DN 400;
-   for an operating temperature range from - 20  °C to +60 °C,
which operate with fuel gases of the 1st and 2nd  family as defined in EN 437:2003+A1:2009, used in the pressure regulating stations in accordance with EN 12186 or EN 12279, in transmission and distribution networks and also in commercial and industrial installations.
"Gas pressure regulators" hereafter will be called "regulators" except in the titles.
For standard regulators when used in pressure regulating stations complying with EN 12186 or EN 12279, the Annex ZA lists all applicable essential safety requirements of the European legislation on pressure equipment except external and internal corrosion resistance for applications in corrosive environment.
This document considers the following temperature classes/types of regulators:
-   temperature class 1: operating temperature range from −10 °C to 60 °C;
-   temperature class 2: operating temperature range from −20 °C to 60 °C;
-   type IS: (integral strength type);
-   type DS: (differential strength type).
This document applies to regulators which use the pipeline gas as a source of control energy unassisted by any external power source.
The regulator may incorporate a second regulator, used as monitor, complying with the requirements in this document.
The regulator may incorporate a safety shut off device (SSD) complying with the requirements of EN 14382.
The regulator may incorporate a creep (venting) relief device, complying with the requirements in Annex E and/or a vent limiter, complying with the requirements in Annex I.
This document does not apply to:
-   regulators upstream from/on/in domestic gas-consuming appliances which are installed downstream of domestic gas meters;
-   regulators designed to be incorporated into pressure control systems used in service lines ) with volumetric flow rate ≤ 200 m3/h at normal conditions and inlet pressure ≤ 5 bar;
-   regulators for which a specific document exists (e.g. EN 88-1 and EN 88-2, etc.);
-   industrial process control valves in accordance with EN 1349.
The normative Annex G of this document lists some suitable materials for pressure bearing parts, inner metallic partition walls, auxiliary devices, integral process and sensing lines, connectors and fasteners. Other materials may be used when complying with the restrictions given in Table 5.
Continued integrity of gas pressure regulators is ensured by suitable surveillance checks and maintenance. For periodic functional checks and maintenance it is common to refer to national regulations/standards where existing or users/manufacturers practices.
This document has introduced the reaction of the pressure regulators to the specified reasonable expected failures in terms of "fail close" and "fail open" pressure regulator types, but it should be considered that there are other types of failures whose consequences can bring to the same reactions (these risks are covered via redundancy as per EN 12186) and that residual hazards will be reduced by a suitable surveillance in use / maintenance.
In this document, both pressure regulators that can be classified as "safety accessories" by themselves (monitors) according to European legislation on pressure equipment as well as regulators that can be used to provide the necessary pressure protection through redundancy (e.g. pressure regulator with integrated safety shut-off device, pressure regulator + in-line monitor, pressure regulator + safety shut off device) are considered.
The provisions in this document are in line with the state of art at the moment of writing.

This document specifies constructional, functional, testing marking and sizing requirements and documentation of gas safety shut-off devices:
-   for inlet pressures up to 100 bar and nominal diameters up to DN 400;
-   for an operating temperature range from -20 °C to +60 °C;
which operate with fuel gases of the 1st and 2nd family as defined in EN 437, used in the pressure regulating stations in accordance with EN 12186 or EN 12279, in transmission and distribution networks and also in commercial and industrial installations.
"Gas safety shut-off devices" will hereafter be called "SSDs" except in titles.
For standard safety shut-off devices when used in pressure regulating stations complying with EN 12186 or EN 12279, Annex ZA lists all applicable Essential Safety Requirements of Directive 2014/68/EU (PED).
This document considers the following temperature classes/types of SSDs:
-   temperature class 1: operating temperature range from -10 °C to 60 °C;
-   temperature class 2: operating temperature range from -20 °C to 60 °C;
-   functional class A: SSDs that close when damage to the pressure detecting element occurs or when external power fails and whose re-opening, is possible only manually;
-   functional class B: SSDs that do not close when damage to the pressure detecting element occurs but provide suitable and reliable protection and whose re-opening, is possible only manually;
-   type IS: (integral strength type);
-   type DS: (differential strength type).
SSDs complying with the requirements of this document may be declared as "in conformity with EN 14382" and bear the mark "EN 14382".
The material and functional requirements specified in this document may be applied to SSDs which use thermal energy or the effects of electrical energy to trip the operation of the closing member. For these SSDs the operational parameters are not specified in this document.
The SSD may incorporate a vent limiter, complying with the requirements in Annex J.
This standard for some paragraphs and sub clauses makes full reference to prEN 334:2016.
This document does not apply to:
-   SSDs upstream from/on/in domestic gas-consuming appliances which are installed downstream of domestic gas meters;
-   SSDs designed to be incorporated into pressure-regulating devices used in service lines  with volumetric flow rate ≤ 200 m3/h at normal conditions and inlet pressure ≤ 5 bar.
Continued integrity of safety shut-off devices is ensured by periodic functional checks. For periodic functional checks it is common to refer to national regulations/standards where existing or users/manufacturers practices.
This document considers the reaction of the SSDs functional class A to the specified reasonable expected failures in terms of "fail close" behaviour, but it should be consider that there are other types of failures whose consequences cannot bring to the same reactions (these risks are covered via redundancy as per EN 12186) and that residual hazards should be reduced by a suitable surveillance in use / maintenance.
In this document, both safety shut-off devices that can be classified as "safety accessories" by themselves according the Pressure Equipment Directive (2014/68/EU) as well as safety shut-off devices that can be used to provide the necessary pressure protection through redundancy (e.g. shutoff device integrated in a pressure regulator, shut-off device with a second shut-off device) are considered. Addition of environmental considerations;
The provisions in this document are in line with the state of art at the moment of writing.
This document does not intend to limit the improvement of actual provisions (materials, requirements, test methods, acceptance criteria, etc.) or the developing of new provisions for SSDs where they are suitable to ensure an equivalent level of reliability.

This document specifies safety requirements, certain functional requirements, and marking of valves and other components with similar bodies, hereinafter called valves, for use in refrigerating systems including heat pumps.
This document includes requirements for valves with extension pipes.
This document describes the procedure to be followed when designing valve parts subjected to pressure as well as the criteria to be used in the selection of materials.
This document describes methods by which reduced impact values at low temperatures may be taken into account in a safe manner.
This document applies to the design of bodies and bonnets for pressure relief devices, including bursting disc devices, with respect to pressure containment but it does not apply to any other aspects of the design or application of pressure relief devices.
In addition, this document is applicable to valves with a maximum operating temperature not exceeding 200 °C and a maximum allowable pressure not exceeding 160 bar[1].
[1] 1 bar = 0,1 MPa.

This document describes the calculation of:
—     mass flow for sizing pressure relief devices for parts of refrigerating systems;
—     discharge capacities for pressure relief valves and other pressure relief devices in refrigerating systems including the necessary data for sizing these when relieving to atmosphere or to part of the refrigerating system at lower pressure;
—     the pressure loss in the inlet and outlet lines of pressure relief valves and other pressure relief devices and includes the necessary data.
This document specifies the requirements for selection of pressure relief devices to prevent excessive pressure due to internal and external heat sources, the sources of increasing pressure (e.g. compressor, heaters, etc.) and thermal expansion of trapped liquid.
NOTE            The term "refrigerating system" used in this document includes heat pumps.

This document specifies requirements for limiters which are incorporated into safety systems for shell boilers as specified in EN 12953 1:2012.
The design requirements and examination of the limiters are covered in this document.
NOTE   See Annex E for determination of the characteristic data for use in protective circuits with a safety integrity level (SIL) rating. The requirements for limiters with regard to the safety integrity level (SIL), for example, in accordance with EN 61508 are not covered in this document.

This document specifies the minimum requirements for safety related equipment for shell boilers (generator and/or assemblies) as specified in EN 12953-1:2012, to ensure the boiler operates within the allowable limits (pressure, temperature, etc.) and if the limits are exceeded the energy supply is automatically interrupted and locked out, irrespective of the degree of intervention.
NOTE 1    For this document, the term “boiler” is applicable for generator and/or assemblies.
NOTE 2   The maximum time of operation without manual (human) intervention can be specified for each boiler system.
NOTE 3   Annex C gives recommendations of operation and testing of the boiler system with a maximum time of operation without manual (human) intervention of 24 h and 72 h.

This document specifies operational requirements for static vacuum insulated vessels designed for a maximum allowable pressure of more than 50 kPa (0,5 bar). It can also be used as a guideline for vessels designed for a maximum allowable pressure of less than 50 kPa (0,5 bar).
This document applies to vessels designed for cryogenic fluids specified in ISO 21009-1.
Static cryogenic vessels are often partly equipped by the manufacturer, but can be installed or re- installed by another party, such as the operator, user or owner.
NOTE 1        For the installation of these vessels, additional requirements can apply.
NOTE 2        Some requirements of this document can be covered by local regulations, e.g. safety distances, occupational safety and health.
NOTE 3        Additional requirements can apply to the operation of large scale and field-fabricated vessels.

This document specifies safety requirements, certain functional requirements, and marking of valves and other components with similar bodies, hereinafter called valves, for use in refrigerating systems including heat pumps.
This document includes requirements for valves with extension pipes.
This document describes the procedure to be followed when designing valve parts subjected to pressure as well as the criteria to be used in the selection of materials.
This document describes methods by which reduced impact values at low temperatures may be taken into account in a safe manner.
This document applies to the design of bodies and bonnets for pressure relief devices, including bursting disc devices, with respect to pressure containment but it does not apply to any other aspects of the design or application of pressure relief devices.
In addition, this document is applicable to valves with a maximum operating temperature not exceeding 200 °C and a maximum allowable pressure not exceeding 160 bar[1].
[1] 1 bar = 0,1 MPa.

This European Standard specifies the requirements for the design and testing of spring loaded pressure relief valves and thermal expansion valves for use in:
- static LPG pressure vessels,
NOTE   The pressure vessels can be situated above ground, underground or mounded.
- transportable LPG welded steel pressure drums,
- LPG pressure vessels on road tankers, rail tankers, tank-containers or demountable tanks.
This document does not address relief valves for LPG cylinders, which are identified in EN 13953.
This document does not address production testing.
Normative Annex B prescribes testing with conditioning at - 40 °C for valves for use under extreme low temperature conditions.
The requirements for pressure relief valve accessories such as isolating devices, changeover manifolds and vent pipes are specified in EN 14071.
EN 14570 identifies the requirements for the pressure relief valve capacities for static pressure vessels.
EN 12252 identifies the requirements for the pressure relief valve capacities for road tankers.
Valves designed in accordance with this standard are specifically for use in LPG applications. Valves manufactured in accordance with EN ISO 4126 1 may also be used in certain LPG applications.
Terms used with LPG pressure relief valves are described graphically in Annex A.

This document specifies the design, testing and inspection requirements for pressure relief valve isolating devices, valve manifolds, vent pipes and system assemblies which are, where necessary, used with pressure relief valves for use in static pressure vessels for Liquefied Petroleum Gas (LPG) service.
This document addresses both prototype testing and production testing of isolating devices and PRV manifolds.
Pressure relief valves for LPG pressure vessels are specified in EN 14129:2014.

This document specifies the technical delivery conditions in two test categories for seamless tubes of circular cross section, with specified elevated temperature properties, made of non-alloy and alloy steel.
This Part of EN 10216 is also be applied for tubes of non-circular cross section; necessary modification will be agreed at the time of enquiry and order.

This document specifies the requirements, sampling, test methods and conditions of delivery for seamless round copper tubes, smooth or inner finned, used for heat exchangers and their internal connecting pipes in the manufacturing of refrigeration and air conditioning equipment.
It is applicable to tubes with an outside diameter from 3,97 mm up to and including 219 mm.
NOTE   The tubes are supplied in straight length or as coils.

This document specifies how a preliminary welding procedure specification (pWPS) is qualified by welding procedure tests.
This document specifies the conditions for the execution of welding procedure tests and the qualification range for welding procedures for all practical welding operations within the range of variables listed in Clause 8.
This document specifies the required tests. Additional tests can be required by application standards.
This document applies to the arc welding of titanium, zirconium and their alloys in all product forms. Arc welding is covered by the following processes in accordance with ISO 4063:
131 – metal inert gas welding, MIG welding;
14 – tungsten inert gas welding, TIG welding;
15 – plasma arc welding.
The principles of this document can be applied to other fusion welding processes.

This document specifies the technical delivery conditions in two test categories for seamless tubes of circular cross section, with specified elevated temperature properties, made of non-alloy and alloy steel.
This Part of EN 10216 is also be applied for tubes of non-circular cross section; necessary modification will be agreed at the time of enquiry and order.

This document gives guidance for the involvement of an inspection body independent of the manufacturer of shell boilers as defined in EN 12952-1.

This document specifies the requirements for design, manufacture and installation of corrugated metal hose assemblies for pressure applications, i.e. maximum allowable pressure PS greater than 0,5 bar.

This Part 11 of this European Standard specifies requirements for unfired pressure vessels and their parts made of titanium and titanium alloys in addition to the general requirements for unfired pressure vessels under EN 13445:2014 Parts 1 to 5.
NOTE 1   Cast materials, HIP and additive manufacturing are not included in this version. Details regarding such materials will be subject to an amendment to or a revision of this European Standard.
NOTE 2   Materials in Groups 51.4 and 54 are not included in this version.

This document specifies the requirements for fabrication and installation of piping systems, including supports, designed in accordance with EN 13480-3:2024.

This document specifies the design and calculation of industrial metallic piping systems, including supports, covered by EN 13480 series.

This document defines a calculation method for bolted, gasketed, circular flange joints. Its purpose is to ensure structural integrity and control of leak tightness. It uses gasket parameters based on definitions and test methods specified in EN 13555:2014.
The calculation method is not applicable to joints with a metallic contact out of the sealing face or to joints whose rigidity varies appreciably across gasket width. For gaskets in incompressible materials, which permit large deformations, the results given by the calculation method can be excessively conservative (i.e. required bolting load too high, allowable pressure of the fluid too low, required flange thickness too large, etc.).

This document specifies the requirements for inspection and testing of industrial piping as specified in EN 13480-1:2024 to be performed on individual spools or piping systems, including supports, designed in accordance with EN 13480-3:2024 and EN 13480-6:2024 (if applicable), and fabricated and installed in accordance with EN 13480-4:2024.

This document specifies the requirements for steel products used for industrial piping and supports.
For some metallic materials other than steel, such as spheroidal graphite cast iron, aluminium, nickel, copper, titanium, requirements are or will be formulated in separate parts of this document.
For metallic materials which are not covered by a harmonized material standard and are not likely to be in near future, specific rules are given in this part or the above cited parts of this document.

This European Standard specifies the requirements for industrial piping systems and supports, including safety systems, made of metallic materials with a view to ensure safe operation. This European Standard is applicable to metallic piping above ground, ducted or buried, irrespective of pressure.

This document specifies requirements for industrial piping either totally buried or partly buried and partly run in sleeves or similar protection. It is used in conjunction with the other six parts of
EN 13480:2024 series.
Where buried piping subject to this standard connects to piping installed under other jurisdiction such as pipelines, the transition can be made at a closing element e.g. an isolating or regulating valve separating the two sections. This can be close to the boundary of the industrial site, but can be inside or outside the boundary.
Operating temperature up to 75 °C.
NOTE   For higher temperatures reference can be made to EN 13941-1:2019+A1:2021 and EN 13941 1:2019+A1:2021, but it is kept in mind, that CEN/TC 107 only deals with pre-insulated piping with temperatures up to 140 °C and diameters up to 800 mm, which is state of the art for these products.

This document specifies requirements for industrial piping systems made of aluminium and aluminium alloys in addition to the general requirements for industrial piping according to the series of standards EN 13480:2024 and CEN/TR 13480-7:2017. It specifies requirements for wrought products only.
NOTE   Castings is not covered in this document.

This document specifies design, construction, type and production testing, and marking requirements for both non-insulated cryogenic flexible hoses and insulated vacuum jacketed hoses used for the transfer of cryogenic fluids within the following range of operating conditions:
—     working temperature range: from −270 °C to +65 °C;
—     nominal size (DN): from 10 to 100.
End fittings for mounting of any couplings are within the scope of this document, but the couplings are subject to other standards.

This Part of this document specifies the inspection and testing of individual and serially produced pressure vessels made of steels in accordance with EN 13445-2:2021.
Special provisions for cyclic operation are given in Annex G of this Part.
Special provisions for vessels or vessel parts working in the creep range are given in Annex F and Annex I of this Part.
NOTE   The responsibilities of parties involved in the conformity assessment procedures are given in Directive 2014/68/EU. Guidance on this can be found in CR 13445-7.

This document specifies the requirements, sampling, test methods and conditions of delivery for seamless round copper tubes, smooth or inner finned, used for heat exchangers and their internal connecting pipes in the manufacturing of refrigeration and air conditioning equipment.
It is applicable to tubes with an outside diameter from 3,97 mm up to and including 219 mm.
NOTE   The tubes are supplied in straight length or as coils.

This European Standard specifies the composition, the property requirements and tolerances on dimensions and form for copper and copper alloy die and hand forgings.
The sampling procedures, the methods of test for verification of conformity to the requirements of this standard, and the delivery conditions are also specified.

This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy profiles including L-, T-, U-shaped cross-sections, and bars, finally produced by drawing or extruding.
This European Standard applies to profiles with L-, T- and U-shaped cross-sections which would fit within a circumscribing circle of a maximum 180 mm diameter and to bars with thicknesses from 3 mm up to and including 60 mm and with widths from 6 mm up to and including 120 mm.
The sampling procedures, the methods of test for verification of conformity to the requirements of this European Standard, are also specified.

This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy rod in the shape of circles, squares, hexagons or octagons, finally produced by drawing or extruding intended for general purposes.
The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified.

This document specifies the composition, property requirements and dimensional tolerances for copper alloy hollow rod, finally produced by drawing or extruding, specifically intended for free machining purposes.
NOTE   Hollow products having an outside diameter greater than 80 mm and/or a wall thickness less than 2 mm are most frequently specified in EN 12449.
The sampling procedures, the methods of test for verification of conformity to the requirements of this document, are also specified.

This document specifies the composition, mechanical properties and other relevant characteristics of copper and copper alloys. The sampling procedures and test methods for the verification of conformity to the requirements of this document are also specified.
This document is applicable to:
a)   copper alloy ingots intended to be remelted for later processing (e.g. castings); and
b)   copper and copper alloy castings which are intended for use without subsequent working other than machining.
Recommended practice for the ordering and supply of castings is included in Annex A. Optional supplementary inspection procedures for ingots and castings are included in Annex B.
NOTE   Ingots are not suitable for pressure equipment applications.

This document specifies the composition, property requirements and dimensional tolerances for copper alloy wire, finally produced by drawing, rolling or extruding, intended for general purposes, spring and fastener manufacturing applications.
The sampling procedures and the methods of test for verification of conformity to the requirements of this document are also specified.

This document specifies operational requirements for static vacuum insulated vessels designed for a maximum allowable pressure of more than 50 kPa (0,5 bar). It can also be used as a guideline for vessels designed for a maximum allowable pressure of less than 50 kPa (0,5 bar).
This document applies to vessels designed for cryogenic fluids specified in ISO 21009-1.
Static cryogenic vessels are often partly equipped by the manufacturer, but can be installed or re- installed by another party, such as the operator, user or owner.
NOTE 1        For the installation of these vessels, additional requirements can apply.
NOTE 2        Some requirements of this document can be covered by local regulations, e.g. safety distances, occupational safety and health.
NOTE 3        Additional requirements can apply to the operation of large scale and field-fabricated vessels.

This document specifies the composition, property requirements and dimensional tolerances for copper alloy rod, in the shape of circles, squares, hexagons or octagons, finally produced by drawing or extruding, especially intended for free machining purposes.
The sampling procedures and the methods of test for verification of conformity to the requirements of this document are also specified.

This document specifies the composition, property requirements and dimensional tolerances for copper alloy hollow rod, finally produced by drawing or extruding, specifically intended for free machining purposes.
NOTE   Hollow products having an outside diameter greater than 80 mm and/or a wall thickness less than 2 mm are most frequently specified in EN 12449.
The sampling procedures, the methods of test for verification of conformity to the requirements of this document, are also specified.