EN 602:2026

SLOVENSKI STANDARD
oSIST prEN 602:2025
01-maj-2025
Aluminij in aluminijeve zlitine - Gneteni izdelki - Kemična sestava polizdelkov,
namenjenih za izdelavo izdelkov, ki pridejo v stik z živili
Aluminium and aluminium alloys - Wrought products - Chemical composition of semi-
finished products used for the fabrication of articles for use in contact with foodstuff
Aluminium und Aluminiumlegierungen - Kneterzeugnisse - Chemische
Zusammensetzung von Halbzeug für die Herstellung von Erzeugnissen, die in Kontakt
mit Lebensmitteln kommen
Aluminium et alliages d'aluminium - Produits corroyés - Composition chimique des demi-
produits utilisés pour la fabrication d'articles destinés à entrer en contact avec les
aliments
Ta slovenski standard je istoveten z: prEN 602
ICS:
67.250 Materiali in predmeti v stiku z Materials and articles in
živili contact with foodstuffs
77.150.10 Aluminijski izdelki Aluminium products
oSIST prEN 602:2025 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

oSIST prEN 602:2025
oSIST prEN 602:2025
DRAFT
EUROPEAN STANDARD
prEN 602
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2025
ICS 67.250; 77.150.10 Will supersede EN 602:2004
English Version
Aluminium and aluminium alloys - Wrought products -
Chemical composition of semi-finished products used for
the fabrication of articles for use in contact with foodstuff
Aluminium et alliages d'aluminium - Produits corroyés Aluminium und Aluminiumlegierungen -
- Composition chimique des demi-produits utilisés Kneterzeugnisse - Chemische Zusammensetzung von
pour la fabrication d'articles destinés à entrer en Halbzeug für die Herstellung von Erzeugnissen, die in
contact avec les denrées alimentaires Kontakt mit Lebensmitteln kommen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 132.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 602:2025 E
worldwide for CEN national Members.

oSIST prEN 602:2025
prEN 602:2025 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Maximum permissible content of elements for foodstuff application . 5
4.1 Wrought aluminium . 5
4.2 Wrought aluminium alloys . 6
5 Selection of wrought aluminium and wrought aluminium alloys . 7
6 Demonstration of conformity with the present standard . 7
Bibliography . 8

oSIST prEN 602:2025
prEN 602:2025 (E)
European foreword
This document (prEN 602:2025) has been prepared by Technical Committee CEN/TC 132 “Aluminium and
aluminium alloys”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN enquiry.
This document will supersede EN 602:2004.
EN 602:2025 includes the following significant technical changes with respect to EN 602:2004:
— addition of bismuth element limitation in Table 2;
— deletion of nickel element limitation from Table 2;
— reference to European Parliament and Council Directive 94/62/EC of 20 December 1994 and its
amendment from 2018 on packaging and packaging waste.
oSIST prEN 602:2025
prEN 602:2025 (E)
1 Scope
This document specifies the maximum percentage content of alloying elements and impurities present in
wrought aluminium and aluminium alloys which are fabricated into materials and articles designed to be in
contact with foodstuff. It contains provisions for the demonstration of conformity of products with the present
standard.
NOTE 1 Materials include semi-finished products. Articles are finished goods.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 573-3, Aluminium and aluminium alloys — Chemical composition and form of wrought products — Part 3:
Chemical composition
EN 10204, Metallic products - Types of inspection documents
EN 12258-1, Aluminium and aluminium alloys - Terms and definitions - Part 1: General terms
3 Terms and definitions
For the purposes of this document the terms and definitions given in EN 12258-1 and the following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available
...