17.040 - Linear and angular measurements
ICS 17.040 Details
Linear and angular measurements
Langen- und Winkelmessungen
Mesurage de longueur et mesurage angulaire
Linearne in kotne meritve
General Information
Frequently Asked Questions
ICS 17.040 is a classification code in the International Classification for Standards (ICS) system. It covers "Linear and angular measurements". The ICS is a hierarchical classification system used to organize international, regional, and national standards, facilitating the search and identification of standards across different fields.
There are 1307 standards classified under ICS 17.040 (Linear and angular measurements). These standards are published by international and regional standardization bodies including ISO, IEC, CEN, CENELEC, and ETSI.
The International Classification for Standards (ICS) is a hierarchical classification system maintained by ISO to organize standards and related documents. It uses a three-level structure with field (2 digits), group (3 digits), and sub-group (2 digits) codes. The ICS helps users find standards by subject area and enables statistical analysis of standards development activities.
e-Library Subscription
Create subscription and get permanent access to documents within 17.040 - Linear and angular measurements
Currently subscription includes documents marked with .We are working on making all documents available within the subscription.
This document specifies the calibration and adjustment of the metrological characteristics of contact (stylus) instruments for the measurement of surface texture by the profile method as defined in ISO 25178-601. The calibration and adjustment specified within this document is intended to be carried out with the aid of measurement standards. NOTE Annex B specifies the calibration and adjustment of metrological characteristics of simplified operator contact (stylus) instruments which do not conform with ISO 25178-601.
- Standard21 pagesEnglish languagesale 15% off
- Standard21 pagesFrench languagesale 15% off
This document specifies the design and characteristics of focus variation instruments for areal measurement of surface topography. Because surface profiles can be extracted from areal surface topography data, the methods described in this document are also applicable to profiling measurements as well. This document applies to focus variation without pattern illumination or with fixed pattern illumination. This document does not cover methods using varying pattern illumination during the measurement.
- Standard19 pagesEnglish languagesale 15% off
- Standard21 pagesFrench languagesale 15% off
This document specifies linear spline filters for the filtration of surface profiles. It defines, in particular, how to separate large- and small-scale lateral components of surface profiles.
The concepts presented for closed profiles are applicable to the case of roundness filtration. Where appropriate, these concepts can be extended to generalized closed profiles, especially for surface profiles with re-entrant features.
Examples for the application of the spline filter are given in Annex A. The influence of the tension parameter on the large-scale lateral component of the profile is shown in Annex B.
- Standard31 pagesEnglish languagee-Library read for1 day
This document specifies the grammar of symbols used in ISO 10360 series in order to identify metrological characteristics of coordinate measuring systems (CMSs) and their specifications.
This document does not provide the meaning of these symbols, neither of whole symbols nor of their components. These meanings are specified in the ISO 10360 documents introducing them.
- Standard21 pagesEnglish languagee-Library read for1 day
This document describes a procedure for the evaluation of the uncertainty of measurements made with tactile Cartesian coordinate measuring machines (CMM). The measurement uncertainty evaluated in accordance with this document indicates the performance of the individual measurement operation, which is not the measuring capability nor test uncertainty when verifying the performance of the CMM against its maximum permissible errors (MPE).
- Technical specification50 pagesEnglish languagesale 15% off
- Technical specification53 pagesFrench languagesale 15% off
This document specifies linear spline filters for the filtration of surface profiles. It defines, in particular, how to separate large- and small-scale lateral components of surface profiles.
The concepts presented for closed profiles are applicable to the case of roundness filtration. Where appropriate, these concepts can be extended to generalized closed profiles, especially for surface profiles with re-entrant features.
Examples for the application of the spline filter are given in Annex A. The influence of the tension parameter on the large-scale lateral component of the profile is shown in Annex B.
- Standard31 pagesEnglish languagee-Library read for1 day
This document specifies linear spline filters for the filtration of surface profiles. It defines, in particular, how to separate large- and small-scale lateral components of surface profiles. The concepts presented for closed profiles are applicable to the case of roundness filtration. Where appropriate, these concepts can be extended to generalized closed profiles, especially for surface profiles with re-entrant features. Examples for the application of the spline filter are given in Annex A. The influence of the tension parameter on the large-scale lateral component of the profile is shown in Annex B.
- Standard23 pagesEnglish languagesale 15% off
- Standard24 pagesFrench languagesale 15% off
This document specifies the grammar of symbols used in ISO 10360 series in order to identify metrological characteristics of coordinate measuring systems (CMSs) and their specifications.
This document does not provide the meaning of these symbols, neither of whole symbols nor of their components. These meanings are specified in the ISO 10360 documents introducing them.
- Standard21 pagesEnglish languagee-Library read for1 day
This document specifies the chamfer least material boundary for ring and washer chamfers of metric series rolling bearings for the corresponding radius maximum material boundaries. The radius maximum material boundaries are given in references[1],[2],[3],[4],[5],[6],[7]. Recommendations are given for the corresponding housing and shaft fillet radii.
- Standard13 pagesEnglish languagesale 15% off
- Standard13 pagesFrench languagesale 15% off
This document specifies the grammar of symbols used in ISO 10360 series in order to identify metrological characteristics of coordinate measuring systems (CMSs) and their specifications. This document does not provide the meaning of these symbols, neither of whole symbols nor of their components. These meanings are specified in the ISO 10360 documents introducing them.
- Standard13 pagesEnglish languagesale 15% off
- Standard13 pagesFrench languagesale 15% off
This document establishes definitions and evaluation methods for the following wheel-rail contact geometry parameters influencing the vehicle running dynamic behaviour: the rolling radius difference between the two wheels of a wheelset (Δr-function) which serves as a basis for all further calculations; the equivalent conicity function from which are derived: a single equivalent conicity value for a specified amplitude, which is relevant for the assessment of vehicle running stability on straight track and in very large radius curves; the nonlinearity parameter, which characterizes the shape of this function and is related to the vehicle behaviour, particularly in the speed range close to the running stability limit; the rolling radii coefficient, which is used to describe the theoretical radial steering capability of a wheelset in a curved track. Additional information is given about the relationship between the contact angles of the two wheels of a wheelset (Δtanγ-function) and about the roll angle parameter. NOTE Out of the presented parameters only those related to the contact angle are relevant for independently rotating wheels of wheel pairs. Descriptions of possible calculation methods are included in this document. Test case calculations are provided to achieve comparable results and to check the proper implementation of the described algorithms. To validate alternative methods not described in this document, acceptance criteria are given for the equivalent conicity function. This includes reference profiles, profile combinations, tolerances and reference results with tolerance limits. This document also includes minimum requirements for the measurement of wheel and rail profiles as well as of the parameters needed for the transformation into a common coordinate system of right-hand and left-hand profiles. This document does not define limits for the wheel-rail contact geometry parameters and gives no tolerances for the rail profile and the wheel profile to achieve acceptable results. For the application of this document some general recommendations are given.
- Standard107 pagesEnglish languagesale 15% off
- Standard110 pagesFrench languagesale 15% off
This document specifies requirements for indicating linear sizes.
This document establishes the default specification operator (see ISO 17450-2) and defines a special specification operator for linear sizes.
This document is applicable to the following features of linear size (see ISO 17450-1):
— cylinders;
— spheres;
— two parallel opposite planes.
This document provides a set of tools to express several types of linear size characteristics. It does not present any information on the relationship between a function or a use and a linear size characteristic.
- Standard64 pagesEnglish languagee-Library read for1 day
This document specifies requirements for indicating linear sizes.
This document establishes the default specification operator (see ISO 17450-2) and defines a special specification operator for linear sizes.
This document is applicable to the following features of linear size (see ISO 17450-1):
— cylinders;
— spheres;
— two parallel opposite planes.
This document provides a set of tools to express several types of linear size characteristics. It does not present any information on the relationship between a function or a use and a linear size characteristic.
- Standard64 pagesEnglish languagee-Library read for1 day
This document specifies the mathematical processing of digitized transverse profile measurements to produce indices in the transverse direction for unevenness, other defects and crossfall. The document describes the calculation methods of the indices, such as irregularities, (1) rut depth, (2) ridge height, (3) water depth and area, (4) crossfall, and how to evaluate and report the indices. It also describes possibilities to do further analysis to examine defects and problems on the road that can be seen in the transverse profile. The latter is described in Annex E.
- Standard40 pagesEnglish languagee-Library read for1 day
This document specifies the method for non-destructive thickness measurement via the magnetic type of electrodeposited nickel coatings, also called “e-nickel”, on magnetic or non-magnetic substrates.
It is possible that the method is not applicable to autocatalytic (electroless) nickel coatings, since these coatings are often non-magnetic due to their chemical composition.
For the purposes of this document, two types of substrates are distinguished:
a) nickel coatings on magnetic substrates (type A coatings);
b) nickel coatings on non-magnetic substrates (type B coatings).
Not all instruments are applicable to both types of coating.
The effective measuring ranges of instruments using the principle of magnetic attraction are up to 50 µm for type A coatings and up to 25 µm for type B coatings.
For instruments using the principle of reluctance, the effective ranges are much greater, up to 1 mm or even more. This method is applicable to both types of coatings.
- Standard15 pagesEnglish languagee-Library read for1 day
This document specifies requirements for indicating linear sizes. This document establishes the default specification operator (see ISO 17450-2) and defines a special specification operator for linear sizes. This document is applicable to the following features of linear size (see ISO 17450-1): — cylinders; — spheres; — two parallel opposite planes. This document provides a set of tools to express several types of linear size characteristics. It does not present any information on the relationship between a function or a use and a linear size characteristic.
- Standard54 pagesEnglish languagesale 15% off
- Standard52 pagesFrench languagesale 15% off
This document specifies the limits of sizes for major, pitch and minor diameters of ISO metric trapezoidal screw threads (Tr) conforming to ISO 2902 and having basic and design profiles in accordance with ISO 2901. This document is applicable to the metric trapezoidal screw threads with the seven tolerance classes (7H, 8H, 9H, 7e, 8e, 8c and 9c) recommended in ISO 2903.
- Standard31 pagesEnglish languagesale 15% off
This document specifies the most important design and metrological characteristics of two-point inside micrometers:
— with a scale interval or digital step of 0,001 mm and 0,01 mm;
— with analogue or digital indication.
This document is applicable to two-point inside micrometers with and without interchangeable extensions.
This document does not apply to micrometers fitted with a dial gauge, or to jaw micrometers.
- Standard21 pagesEnglish languagee-Library read for1 day
This document specifies the most important design and metrological characteristics of two-point inside micrometers:
— with a scale interval or digital step of 0,001 mm and 0,01 mm;
— with analogue or digital indication.
This document is applicable to two-point inside micrometers with and without interchangeable extensions.
This document does not apply to micrometers fitted with a dial gauge, or to jaw micrometers.
- Standard21 pagesEnglish languagee-Library read for1 day
This document specifies the most important design and metrological characteristics of two-point inside micrometers: — with a scale interval or digital step of 0,001 mm and 0,01 mm; — with analogue or digital indication. This document is applicable to two-point inside micrometers with and without interchangeable extensions. This document does not apply to micrometers fitted with a dial gauge, or to jaw micrometers.
- Standard11 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
This document defines the terminology and develops concepts for profile morphological segmentation. In particular it specifies the watershed segmentation method, the Wolf pruning method and the crossing-the-line method. This document assumes a continuous surface.
- Standard37 pagesEnglish languagee-Library read for1 day
This document specifies the design and metrological characteristics of point autofocus probe (PAP) instruments for the areal measurement of surface topography. Because surface profiles can be extracted from areal surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard24 pagesEnglish languagee-Library read for1 day
This document specifies the design, metrological characteristics and nominal characteristics of contact stylus instruments for the areal measurement of surface topography. Because surface profiles can be extracted from areal surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard25 pagesEnglish languagee-Library read for1 day
This document specifies the design and metrological characteristics of coherence scanning interferometry (CSI) instruments for the areal measurement of surface topography. Because surface profiles can be extracted from surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard31 pagesEnglish languagee-Library read for1 day
This document specifies the design and metrological characteristics of phase shifting interferometry (PSI) instruments for the areal measurement of surface topography. Because surface profiles can be extracted from areal surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard26 pagesEnglish languagee-Library read for1 day
This document specifies the design and metrological characteristics of a particular non-contact instrument for measuring surface texture using a confocal chromatic probe based on axial chromatic aberration of white light. Additional metrological characteristics can be found in ISO 25178-600. Because surface profiles can be extracted from areal surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard23 pagesEnglish languagee-Library read for1 day
This document specifies robust Gaussian regression filters for the filtration of surface profiles. It defines, in particular, how to separate large- and small-scale lateral components of surface profiles with protruding dales and hills.
The concept presented for closed profiles are applicable to the case of roundness filtering. Where appropriate, these concept can be extended to generalized closed profiles, especially for surface profiles with re-entrant features.
- Standard30 pagesEnglish languagee-Library read for1 day
This document defines the terminology and develops concepts for profile morphological segmentation. In particular it specifies the watershed segmentation method, the Wolf pruning method and the crossing-the-line method. This document assumes a continuous surface.
- Standard37 pagesEnglish languagee-Library read for1 day
This document defines the terminology and develops concepts for profile morphological segmentation. In particular it specifies the watershed segmentation method, the Wolf pruning method and the crossing-the-line method. This document assumes a continuous surface.
- Standard29 pagesEnglish languagesale 15% off
- Standard29 pagesFrench languagesale 15% off
This document specifies linear Gaussian filters for the filtration of surface profiles. It defines, in particular, how to separate large- and small-scale lateral components of surface profiles.
The concept presented for closed profiles are applicable to the case of roundness filtration. Where appropriate, these concept can be extended to generalized closed profiles, especially for surface profiles with re-entrant features.
Implementation details are given in Annex A for open profiles and Annex B for closed profiles.
- Standard37 pagesEnglish languagee-Library read for1 day
This document specifies the design, metrological characteristics and nominal characteristics of contact stylus instruments for the areal measurement of surface topography. Because surface profiles can be extracted from areal surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard25 pagesEnglish languagee-Library read for1 day
This document specifies the design and metrological characteristics of point autofocus probe (PAP) instruments for the areal measurement of surface topography. Because surface profiles can be extracted from areal surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard24 pagesEnglish languagee-Library read for1 day
This document specifies the design and metrological characteristics of coherence scanning interferometry (CSI) instruments for the areal measurement of surface topography. Because surface profiles can be extracted from surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard31 pagesEnglish languagee-Library read for1 day
This document specifies the design and metrological characteristics of a particular non-contact instrument for measuring surface texture using a confocal chromatic probe based on axial chromatic aberration of white light. Additional metrological characteristics can be found in ISO 25178-600. Because surface profiles can be extracted from areal surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard23 pagesEnglish languagee-Library read for1 day
This document specifies the design and metrological characteristics of phase shifting interferometry (PSI) instruments for the areal measurement of surface topography. Because surface profiles can be extracted from areal surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard26 pagesEnglish languagee-Library read for1 day
This document specifies robust Gaussian regression filters for the filtration of surface profiles. It defines, in particular, how to separate large- and small-scale lateral components of surface profiles with protruding dales and hills.
The concept presented for closed profiles are applicable to the case of roundness filtering. Where appropriate, these concept can be extended to generalized closed profiles, especially for surface profiles with re-entrant features.
- Standard30 pagesEnglish languagee-Library read for1 day
This document specifies the design and metrological characteristics of a particular non-contact instrument for measuring surface texture using a confocal chromatic probe based on axial chromatic aberration of white light. Additional metrological characteristics can be found in ISO 25178-600. Because surface profiles can be extracted from areal surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard15 pagesEnglish languagesale 15% off
- Standard16 pagesFrench languagesale 15% off
This document specifies the design and metrological characteristics of point autofocus probe (PAP) instruments for the areal measurement of surface topography. Because surface profiles can be extracted from areal surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard16 pagesEnglish languagesale 15% off
- Standard17 pagesFrench languagesale 15% off
This document specifies the design, metrological characteristics and nominal characteristics of contact stylus instruments for the areal measurement of surface topography. Because surface profiles can be extracted from areal surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard16 pagesEnglish languagesale 15% off
- Standard18 pagesFrench languagesale 15% off
This document specifies the design and metrological characteristics of coherence scanning interferometry (CSI) instruments for the areal measurement of surface topography. Because surface profiles can be extracted from surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard23 pagesEnglish languagesale 15% off
- Standard24 pagesFrench languagesale 15% off
This document specifies the design and metrological characteristics of phase shifting interferometry (PSI) instruments for the areal measurement of surface topography. Because surface profiles can be extracted from areal surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard18 pagesEnglish languagesale 15% off
- Standard19 pagesFrench languagesale 15% off
This document specifies linear Gaussian filters for the filtration of surface profiles. It defines, in particular, how to separate large- and small-scale lateral components of surface profiles.
The concept presented for closed profiles are applicable to the case of roundness filtration. Where appropriate, these concept can be extended to generalized closed profiles, especially for surface profiles with re-entrant features.
Implementation details are given in Annex A for open profiles and Annex B for closed profiles.
- Standard37 pagesEnglish languagee-Library read for1 day
This document specifies robust Gaussian regression filters for the filtration of surface profiles. It defines, in particular, how to separate large- and small-scale lateral components of surface profiles with protruding dales and hills. The concept presented for closed profiles are applicable to the case of roundness filtering. Where appropriate, these concept can be extended to generalized closed profiles, especially for surface profiles with re-entrant features.
- Standard22 pagesEnglish languagesale 15% off
- Standard22 pagesFrench languagesale 15% off
This document specifies linear Gaussian filters for the filtration of surface profiles. It defines, in particular, how to separate large- and small-scale lateral components of surface profiles. The concept presented for closed profiles are applicable to the case of roundness filtration. Where appropriate, these concept can be extended to generalized closed profiles, especially for surface profiles with re-entrant features. Implementation details are given in Annex A for open profiles and Annex B for closed profiles.
- Standard29 pagesEnglish languagesale 15% off
- Standard31 pagesFrench languagesale 15% off
- Amendment7 pagesEnglish languagee-Library read for1 day
This document specifies terminology, rules and methodology for the indication and understanding of datums and datum systems in technical product documentation. This document also provides explanations to assist the user in understanding the concepts involved.
This document defines the specification operator (see ISO 17450-2) used to establish a datum or datum system. The verification operator (see ISO 17450-2) can take different forms (physically or mathematically) and is not the subject of this document.
NOTE The detailed rules for maximum and least material requirements for datums are given in ISO 2692.
- Standard125 pagesEnglish languagee-Library read for1 day
This document specifies terminology, rules and methodology for the indication and understanding of datums and datum systems in technical product documentation. This document also provides explanations to assist the user in understanding the concepts involved.
This document defines the specification operator (see ISO 17450-2) used to establish a datum or datum system. The verification operator (see ISO 17450-2) can take different forms (physically or mathematically) and is not the subject of this document.
NOTE The detailed rules for maximum and least material requirements for datums are given in ISO 2692.
- Standard125 pagesEnglish languagee-Library read for1 day
This document specifies the most important design and metrological characteristics of rotary axis form-measuring instruments.
It is not applicable to coordinate measurement systems as defined by the ISO 10360 series, whether the systems are fitted with a rotary axis or not, except by special agreement.
- Standard58 pagesEnglish languagee-Library read for1 day
This document specifies terminology, rules and methodology for the indication and understanding of datums and datum systems in technical product documentation. This document also provides explanations to assist the user in understanding the concepts involved. This document defines the specification operator (see ISO 17450-2) used to establish a datum or datum system. The verification operator (see ISO 17450-2) can take different forms (physically or mathematically) and is not the subject of this document. NOTE The detailed rules for maximum and least material requirements for datums are given in ISO 2692.
- Standard115 pagesEnglish languagesale 15% off
- Standard121 pagesFrench languagesale 15% off
This document specifies the most important design and metrological characteristics of rotary axis form-measuring instruments.
It is not applicable to coordinate measurement systems as defined by the ISO 10360 series, whether the systems are fitted with a rotary axis or not, except by special agreement.
- Standard58 pagesEnglish languagee-Library read for1 day