17.040.40 - Geometrical Product Specification (GPS)
ICS 17.040.40 Details
Geometrical Product Specification (GPS)
Spécification géométrique des produits (GPS)
Specifikacija geometrijskih veličin izdelka (GPS)
General Information
Frequently Asked Questions
ICS 17.040.40 is a classification code in the International Classification for Standards (ICS) system. It covers "Geometrical Product Specification (GPS)". The ICS is a hierarchical classification system used to organize international, regional, and national standards, facilitating the search and identification of standards across different fields.
There are 407 standards classified under ICS 17.040.40 (Geometrical Product Specification (GPS)). These standards are published by international and regional standardization bodies including ISO, IEC, CEN, CENELEC, and ETSI.
The International Classification for Standards (ICS) is a hierarchical classification system maintained by ISO to organize standards and related documents. It uses a three-level structure with field (2 digits), group (3 digits), and sub-group (2 digits) codes. The ICS helps users find standards by subject area and enables statistical analysis of standards development activities.
e-Library Subscription
Create subscription and get permanent access to documents within 17.040.40 - Geometrical Product Specification (GPS)
Currently subscription includes documents marked with .We are working on making all documents available within the subscription.
This document specifies the calibration and adjustment of the metrological characteristics of contact (stylus) instruments for the measurement of surface texture by the profile method as defined in ISO 25178-601. The calibration and adjustment specified within this document is intended to be carried out with the aid of measurement standards. NOTE Annex B specifies the calibration and adjustment of metrological characteristics of simplified operator contact (stylus) instruments which do not conform with ISO 25178-601.
- Standard21 pagesEnglish languagesale 15% off
- Standard21 pagesFrench languagesale 15% off
This document specifies the design and characteristics of focus variation instruments for areal measurement of surface topography. Because surface profiles can be extracted from areal surface topography data, the methods described in this document are also applicable to profiling measurements as well. This document applies to focus variation without pattern illumination or with fixed pattern illumination. This document does not cover methods using varying pattern illumination during the measurement.
- Standard19 pagesEnglish languagesale 15% off
- Standard21 pagesFrench languagesale 15% off
This document specifies linear spline filters for the filtration of surface profiles. It defines, in particular, how to separate large- and small-scale lateral components of surface profiles.
The concepts presented for closed profiles are applicable to the case of roundness filtration. Where appropriate, these concepts can be extended to generalized closed profiles, especially for surface profiles with re-entrant features.
Examples for the application of the spline filter are given in Annex A. The influence of the tension parameter on the large-scale lateral component of the profile is shown in Annex B.
- Standard31 pagesEnglish languagee-Library read for1 day
This document specifies the grammar of symbols used in ISO 10360 series in order to identify metrological characteristics of coordinate measuring systems (CMSs) and their specifications.
This document does not provide the meaning of these symbols, neither of whole symbols nor of their components. These meanings are specified in the ISO 10360 documents introducing them.
- Standard21 pagesEnglish languagee-Library read for1 day
This document describes a procedure for the evaluation of the uncertainty of measurements made with tactile Cartesian coordinate measuring machines (CMM). The measurement uncertainty evaluated in accordance with this document indicates the performance of the individual measurement operation, which is not the measuring capability nor test uncertainty when verifying the performance of the CMM against its maximum permissible errors (MPE).
- Technical specification50 pagesEnglish languagesale 15% off
- Technical specification53 pagesFrench languagesale 15% off
This document specifies linear spline filters for the filtration of surface profiles. It defines, in particular, how to separate large- and small-scale lateral components of surface profiles.
The concepts presented for closed profiles are applicable to the case of roundness filtration. Where appropriate, these concepts can be extended to generalized closed profiles, especially for surface profiles with re-entrant features.
Examples for the application of the spline filter are given in Annex A. The influence of the tension parameter on the large-scale lateral component of the profile is shown in Annex B.
- Standard31 pagesEnglish languagee-Library read for1 day
This document specifies linear spline filters for the filtration of surface profiles. It defines, in particular, how to separate large- and small-scale lateral components of surface profiles. The concepts presented for closed profiles are applicable to the case of roundness filtration. Where appropriate, these concepts can be extended to generalized closed profiles, especially for surface profiles with re-entrant features. Examples for the application of the spline filter are given in Annex A. The influence of the tension parameter on the large-scale lateral component of the profile is shown in Annex B.
- Standard23 pagesEnglish languagesale 15% off
- Standard24 pagesFrench languagesale 15% off
This document specifies the grammar of symbols used in ISO 10360 series in order to identify metrological characteristics of coordinate measuring systems (CMSs) and their specifications.
This document does not provide the meaning of these symbols, neither of whole symbols nor of their components. These meanings are specified in the ISO 10360 documents introducing them.
- Standard21 pagesEnglish languagee-Library read for1 day
This document specifies the chamfer least material boundary for ring and washer chamfers of metric series rolling bearings for the corresponding radius maximum material boundaries. The radius maximum material boundaries are given in references[1],[2],[3],[4],[5],[6],[7]. Recommendations are given for the corresponding housing and shaft fillet radii.
- Standard13 pagesEnglish languagesale 15% off
- Standard13 pagesFrench languagesale 15% off
This document specifies the grammar of symbols used in ISO 10360 series in order to identify metrological characteristics of coordinate measuring systems (CMSs) and their specifications. This document does not provide the meaning of these symbols, neither of whole symbols nor of their components. These meanings are specified in the ISO 10360 documents introducing them.
- Standard13 pagesEnglish languagesale 15% off
- Standard13 pagesFrench languagesale 15% off
This document specifies requirements for indicating linear sizes.
This document establishes the default specification operator (see ISO 17450-2) and defines a special specification operator for linear sizes.
This document is applicable to the following features of linear size (see ISO 17450-1):
— cylinders;
— spheres;
— two parallel opposite planes.
This document provides a set of tools to express several types of linear size characteristics. It does not present any information on the relationship between a function or a use and a linear size characteristic.
- Standard64 pagesEnglish languagee-Library read for1 day
This document specifies requirements for indicating linear sizes.
This document establishes the default specification operator (see ISO 17450-2) and defines a special specification operator for linear sizes.
This document is applicable to the following features of linear size (see ISO 17450-1):
— cylinders;
— spheres;
— two parallel opposite planes.
This document provides a set of tools to express several types of linear size characteristics. It does not present any information on the relationship between a function or a use and a linear size characteristic.
- Standard64 pagesEnglish languagee-Library read for1 day
This document specifies requirements for indicating linear sizes. This document establishes the default specification operator (see ISO 17450-2) and defines a special specification operator for linear sizes. This document is applicable to the following features of linear size (see ISO 17450-1): — cylinders; — spheres; — two parallel opposite planes. This document provides a set of tools to express several types of linear size characteristics. It does not present any information on the relationship between a function or a use and a linear size characteristic.
- Standard54 pagesEnglish languagesale 15% off
- Standard52 pagesFrench languagesale 15% off
This document specifies the most important design and metrological characteristics of two-point inside micrometers:
— with a scale interval or digital step of 0,001 mm and 0,01 mm;
— with analogue or digital indication.
This document is applicable to two-point inside micrometers with and without interchangeable extensions.
This document does not apply to micrometers fitted with a dial gauge, or to jaw micrometers.
- Standard21 pagesEnglish languagee-Library read for1 day
This document specifies the most important design and metrological characteristics of two-point inside micrometers:
— with a scale interval or digital step of 0,001 mm and 0,01 mm;
— with analogue or digital indication.
This document is applicable to two-point inside micrometers with and without interchangeable extensions.
This document does not apply to micrometers fitted with a dial gauge, or to jaw micrometers.
- Standard21 pagesEnglish languagee-Library read for1 day
This document specifies the most important design and metrological characteristics of two-point inside micrometers: — with a scale interval or digital step of 0,001 mm and 0,01 mm; — with analogue or digital indication. This document is applicable to two-point inside micrometers with and without interchangeable extensions. This document does not apply to micrometers fitted with a dial gauge, or to jaw micrometers.
- Standard11 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
This document defines the terminology and develops concepts for profile morphological segmentation. In particular it specifies the watershed segmentation method, the Wolf pruning method and the crossing-the-line method. This document assumes a continuous surface.
- Standard37 pagesEnglish languagee-Library read for1 day
This document specifies the design and metrological characteristics of point autofocus probe (PAP) instruments for the areal measurement of surface topography. Because surface profiles can be extracted from areal surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard24 pagesEnglish languagee-Library read for1 day
This document specifies the design and metrological characteristics of coherence scanning interferometry (CSI) instruments for the areal measurement of surface topography. Because surface profiles can be extracted from surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard31 pagesEnglish languagee-Library read for1 day
This document specifies the design and metrological characteristics of phase shifting interferometry (PSI) instruments for the areal measurement of surface topography. Because surface profiles can be extracted from areal surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard26 pagesEnglish languagee-Library read for1 day
This document specifies the design and metrological characteristics of a particular non-contact instrument for measuring surface texture using a confocal chromatic probe based on axial chromatic aberration of white light. Additional metrological characteristics can be found in ISO 25178-600. Because surface profiles can be extracted from areal surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard23 pagesEnglish languagee-Library read for1 day
This document specifies the design, metrological characteristics and nominal characteristics of contact stylus instruments for the areal measurement of surface topography. Because surface profiles can be extracted from areal surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard25 pagesEnglish languagee-Library read for1 day
This document specifies robust Gaussian regression filters for the filtration of surface profiles. It defines, in particular, how to separate large- and small-scale lateral components of surface profiles with protruding dales and hills.
The concept presented for closed profiles are applicable to the case of roundness filtering. Where appropriate, these concept can be extended to generalized closed profiles, especially for surface profiles with re-entrant features.
- Standard30 pagesEnglish languagee-Library read for1 day
This document defines the terminology and develops concepts for profile morphological segmentation. In particular it specifies the watershed segmentation method, the Wolf pruning method and the crossing-the-line method. This document assumes a continuous surface.
- Standard37 pagesEnglish languagee-Library read for1 day
This document specifies linear Gaussian filters for the filtration of surface profiles. It defines, in particular, how to separate large- and small-scale lateral components of surface profiles.
The concept presented for closed profiles are applicable to the case of roundness filtration. Where appropriate, these concept can be extended to generalized closed profiles, especially for surface profiles with re-entrant features.
Implementation details are given in Annex A for open profiles and Annex B for closed profiles.
- Standard37 pagesEnglish languagee-Library read for1 day
This document defines the terminology and develops concepts for profile morphological segmentation. In particular it specifies the watershed segmentation method, the Wolf pruning method and the crossing-the-line method. This document assumes a continuous surface.
- Standard29 pagesEnglish languagesale 15% off
- Standard29 pagesFrench languagesale 15% off
This document specifies the design and metrological characteristics of phase shifting interferometry (PSI) instruments for the areal measurement of surface topography. Because surface profiles can be extracted from areal surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard26 pagesEnglish languagee-Library read for1 day
This document specifies the design and metrological characteristics of point autofocus probe (PAP) instruments for the areal measurement of surface topography. Because surface profiles can be extracted from areal surface topography data, the methods described in this document are also applicable to profiling measurements.
- Standard24 pagesEnglish languagee-Library read for1 day
This document specifies robust Gaussian regression filters for the filtration of surface profiles. It defines, in particular, how to separate large- and small-scale lateral components of surface profiles with protruding dales and hills.
The concept presented for closed profiles are applicable to the case of roundness filtering. Where appropriate, these concept can be extended to generalized closed profiles, especially for surface profiles with re-entrant features.
- Standard30 pagesEnglish languagee-Library read for1 day
This document specifies linear Gaussian filters for the filtration of surface profiles. It defines, in particular, how to separate large- and small-scale lateral components of surface profiles.
The concept presented for closed profiles are applicable to the case of roundness filtration. Where appropriate, these concept can be extended to generalized closed profiles, especially for surface profiles with re-entrant features.
Implementation details are given in Annex A for open profiles and Annex B for closed profiles.
- Standard37 pagesEnglish languagee-Library read for1 day
This document specifies robust Gaussian regression filters for the filtration of surface profiles. It defines, in particular, how to separate large- and small-scale lateral components of surface profiles with protruding dales and hills. The concept presented for closed profiles are applicable to the case of roundness filtering. Where appropriate, these concept can be extended to generalized closed profiles, especially for surface profiles with re-entrant features.
- Standard22 pagesEnglish languagesale 15% off
- Standard22 pagesFrench languagesale 15% off
This document specifies linear Gaussian filters for the filtration of surface profiles. It defines, in particular, how to separate large- and small-scale lateral components of surface profiles. The concept presented for closed profiles are applicable to the case of roundness filtration. Where appropriate, these concept can be extended to generalized closed profiles, especially for surface profiles with re-entrant features. Implementation details are given in Annex A for open profiles and Annex B for closed profiles.
- Standard29 pagesEnglish languagesale 15% off
- Standard31 pagesFrench languagesale 15% off
This document specifies terminology, rules and methodology for the indication and understanding of datums and datum systems in technical product documentation. This document also provides explanations to assist the user in understanding the concepts involved.
This document defines the specification operator (see ISO 17450-2) used to establish a datum or datum system. The verification operator (see ISO 17450-2) can take different forms (physically or mathematically) and is not the subject of this document.
NOTE The detailed rules for maximum and least material requirements for datums are given in ISO 2692.
- Standard125 pagesEnglish languagee-Library read for1 day
This document specifies terminology, rules and methodology for the indication and understanding of datums and datum systems in technical product documentation. This document also provides explanations to assist the user in understanding the concepts involved.
This document defines the specification operator (see ISO 17450-2) used to establish a datum or datum system. The verification operator (see ISO 17450-2) can take different forms (physically or mathematically) and is not the subject of this document.
NOTE The detailed rules for maximum and least material requirements for datums are given in ISO 2692.
- Standard125 pagesEnglish languagee-Library read for1 day
This document specifies the most important design and metrological characteristics of rotary axis form-measuring instruments.
It is not applicable to coordinate measurement systems as defined by the ISO 10360 series, whether the systems are fitted with a rotary axis or not, except by special agreement.
- Standard58 pagesEnglish languagee-Library read for1 day
This document specifies terminology, rules and methodology for the indication and understanding of datums and datum systems in technical product documentation. This document also provides explanations to assist the user in understanding the concepts involved. This document defines the specification operator (see ISO 17450-2) used to establish a datum or datum system. The verification operator (see ISO 17450-2) can take different forms (physically or mathematically) and is not the subject of this document. NOTE The detailed rules for maximum and least material requirements for datums are given in ISO 2692.
- Standard115 pagesEnglish languagesale 15% off
- Standard121 pagesFrench languagesale 15% off
This document specifies the most important design and metrological characteristics of rotary axis form-measuring instruments.
It is not applicable to coordinate measurement systems as defined by the ISO 10360 series, whether the systems are fitted with a rotary axis or not, except by special agreement.
- Standard58 pagesEnglish languagee-Library read for1 day
This document specifies the most important design and metrological characteristics of rotary axis form-measuring instruments. It is not applicable to coordinate measurement systems as defined by the ISO 10360 series, whether the systems are fitted with a rotary axis or not, except by special agreement.
- Standard50 pagesEnglish languagesale 15% off
- Standard52 pagesFrench languagesale 15% off
This document defines the basic terms for partitioned features and establishes a framework for the fundamental procedures used in partition.
- Standard24 pagesEnglish languagee-Library read for1 day
This document defines the basic terms for partitioned features and establishes a framework for the fundamental procedures used in partition.
- Standard24 pagesEnglish languagee-Library read for1 day
This document defines the basic terms for partitioned features and establishes a framework for the fundamental procedures used in partition.
- Standard16 pagesEnglish languagesale 15% off
- Standard17 pagesFrench languagesale 15% off
This document specifies the procedure for the partition operation of geometrical product specification and verification.
This document does not apply to profile and areal surface texture.
- Standard28 pagesEnglish languagee-Library read for1 day
This document specifies the methods used to partition a nominal model.
- Standard14 pagesEnglish languagee-Library read for1 day
This document specifies the procedure for the partition operation of geometrical product specification and verification.
This document does not apply to profile and areal surface texture.
- Standard28 pagesEnglish languagee-Library read for1 day
This document specifies the methods used to partition a nominal model.
- Standard14 pagesEnglish languagee-Library read for1 day
This document specifies the procedure for the partition operation of geometrical product specification and verification. This document does not apply to profile and areal surface texture.
- Standard20 pagesEnglish languagesale 15% off
- Standard20 pagesFrench languagesale 15% off
This document specifies the methods used to partition a nominal model.
- Standard6 pagesEnglish languagesale 15% off
- Standard6 pagesFrench languagesale 15% off
This document gives the terminology and basic concepts of association, including objective functions and association constraints and material offset.
This document is not intended to specify association defaults and GPS syntax which are introduced in other (ISO GPS) International Standards.
NOTE The association can be used to establish for example:
— a datum;
— a reference feature for a geometrical specification or for a surface texture specification;
— an associated toleranced feature;
— any dimensional characteristic;
— an intersection plane, an orientation plane, a collection plane or a direction feature.
- Standard24 pagesEnglish languagee-Library read for1 day
This document gives the terminology and basic concepts of association, including objective functions and association constraints and material offset.
This document is not intended to specify association defaults and GPS syntax which are introduced in other (ISO GPS) International Standards.
NOTE The association can be used to establish for example:
— a datum;
— a reference feature for a geometrical specification or for a surface texture specification;
— an associated toleranced feature;
— any dimensional characteristic;
— an intersection plane, an orientation plane, a collection plane or a direction feature.
- Standard24 pagesEnglish languagee-Library read for1 day
This document gives the terminology and basic concepts of association, including objective functions and association constraints and material offset. This document is not intended to specify association defaults and GPS syntax which are introduced in other (ISO GPS) International Standards. NOTE The association can be used to establish for example: — a datum; — a reference feature for a geometrical specification or for a surface texture specification; — an associated toleranced feature; — any dimensional characteristic; — an intersection plane, an orientation plane, a collection plane or a direction feature.
- Standard16 pagesEnglish languagesale 15% off
- Standard16 pagesFrench languagesale 15% off