SIST EN 60358-2:2014

SLOVENSKI STANDARD
01-marec-2014
1DGRPHãþD
SIST HD 597 S1:2001
6NORSQLNRQGHQ]DWRUMLLQNRQGHQ]DWRUVNLGHOLOQLNLGHO,]PHQLþQLDOLHQRVPHUQL
HQRID]QLVNORSQLNRQGHQ]DWRUYH]DQPHGYRGQLNRPLQ]HPOMR]DDSOLNDFLMH]
QRVLOQRIUHNYHQFRSULNRPXQLNDFLMDKSRHQHUJHWVNLKYRGLK3/&,(&

Coupling capacitors and capacitor dividers - Part 2: AC or DC single-phase coupling
capacitor connected between line and ground for power line carrier-frequency (PLC)
application
/
Condensateur de couplage monophasé à courant alternatif ou à courant continu
connecté entre la ligne et la terre pour application aux liaisons à courant porteur sur
lignes d'énergie (CPL)
Ta slovenski standard je istoveten z: EN 60358-2:2013
ICS:
31.060.99 Drugi kondenzatorji Other capacitors
33.040.60 Telekomunikacije po Powerline
elektroenergetskih vodih telecommunications
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 60358-2
NORME EUROPÉENNE
December 2013
EUROPÄISCHE NORM
ICS 29.120.99; 29.240.99; 31.060.70 Supersedes HD 597 S1:1992 (partially)

English version
Coupling capacitors and capacitor dividers -
Part 2: AC or DC single-phase coupling capacitor connected between line and
ground for power line carrier-frequency (PLC) application
(IEC 60358-2:2013)
Condensateurs de couplage et diviseurs Kopplungskondensatoren und kapazitive
capacitifs - Teiler -
Partie 2: Condensateur de couplage Teil 2: Einphasen-Kopplungskondensatoren
monophasé à courant alternatif ou à courant für Wechsel- oder Gleichstrom, die für
continu connecté entre la ligne et la terre Trägerfrequenzübertragungen auf
pour application aux liaisons à courant Hochspannungsleitungen (TFH-
porteur sur lignes d’énergie (CPL) Übertragung) zwischen Außenleiter und
(CEI 60358-2:2013) Erde geschaltet sind
(IEC 60358-2:2013)
This European Standard was approved by CENELEC on 2013-09-16. CENELEC members are bound to comply with
the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a
national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to
the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-
CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60358-2:2013 E
Foreword
The text of document 33/531/FDIS, future edition 1 of IEC 60358-2, prepared by IEC/TC 33, "Power
capacitors and their applications" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 60358-2:2013.
The following dates are fixed:
• latest date by which the document has (dop) 2014-06-16
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2016-09-16
• latest date by which the national
standards conflicting with the
document have to be withdrawn
This document supersedes HD 597 S1:1992 (partially).
This European Standard is to be used in conjunction with the latest edition of EN 60358-1 and its
amendments. It was established on the basis of the first edition (2012) of that standard.

This Part 2 supplements or modifies the corresponding clauses in EN 60358-1.

When a particular subclause of Part 1 is not mentioned in this Part 2, that subclause applies as far as is
reasonable. Where this Part 2 states “addition” or “replacement”, the relevant text in Part 1 is to be
adapted accordingly.
For additional clauses, subclauses, figures, tables or annexes, the following numbering system is used:
– subclauses, tables and figures which are additional to those in Part 1 are numbered starting from 200;
– additional annexes are lettered AA, BB etc.
– as the notes are integrated into the clauses, their numbering starts from 1 as usual.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 60358-2:2013 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60085 NOTE  Harmonized as EN 60085.
IEC 60721 Series NOTE  Harmonized in EN 60721 series.
IEC 61462 NOTE  Harmonized as EN 61462.
CISPR 16-1-1 NOTE  Harmonized as EN 55016-1-1.

- 3 - EN 60358-2:2013
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
IEC 60060-1 High-voltage test techniques - Part 1: General EN 60060-1
definitions and test requirements

IEC 60060-2 High-voltage test techniques - Part 2: EN 60060-2
Measuring systems
IEC 60358-1 2012 Coupling capacitors and capacitor dividers - EN 60358-1 2012
+ corr. July 2013 Part 1: General rules + AC:2013 2013

IEC 60481 Coupling devices for power line carrier - -
systems
IEC 61869-5 Instrument transformers - Part 5: Additional
requirements for capacitor voltage
transformers
IEC 60358-2 ®
Edition 1.0 2013-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Coupling capacitors and capacitor dividers –

Part 2: AC or DC single-phase coupling capacitor connected between line and

ground for power line carrier-frequency (PLC) application

Condensateurs de couplage et diviseurs capacitifs –

Partie 2: Condensateur de couplage monophasé à courant alternatif ou à

courant continu connecté entre la ligne et la terre pour application aux liaisons à

courant porteur sur lignes d’énergie (CPL)

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX R
ICS 29.120.99; 29.240.99; 31.060.70 ISBN 978-2-8322-1038-3

– 2 – 60358-2 © IEC:2013
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 7
3.200 Carrier-frequency accessories definitions . 8
4 Service conditions . 8
5 Ratings . 8
6 Design requirements . 8
6.200 Design requirements for coupling capacitor and carrier-frequency
accessories . 8
6.200.1 Design requirements for coupling capacitor . 8
6.200.2 Design requirements for carrier-frequency accessories . 9
7 Test conditions . 10
8 Classification of tests . 10
8.1 General . 10
8.2 Routine tests . 10
8.2.200 General . 10
8.2.201 Routine tests for carrier frequency accessories . 10
8.3 Type tests . 10
8.3.200 Type test for coupling capacitor and carrier-frequency
accessories . 10
8.4 Special tests. 11
9 Routine tests . 11
9.1 Tightness of the liquid-filled equipment. 11
9.2 Electrical routine tests . 11
9.2.200 Electrical tests for coupling capacitor and carrier frequency
accessories . 11
10 Type tests . 12
10.200 Test on capacitor . 12
10.200.1 High frequency capacitance and equivalent series resistance . 12
10.200.2 Measurement of the stray capacitance and stray conductance of
the low voltage terminal . 12
10.201 Type test on carrier frequency accessories . 13
10.201.1 General . 13
10.201.2 Type tests for drain coil . 13
10.201.3 Type test for voltage limitation device together with drain coil:
Impulse voltage test . 14
11 Special tests . 14
12 Marking . 15
12.1 General . 15
12.2 Marking of capacitor . 15
12.200 Marking of the carrier-frequency accessories . 15
Annexes . 15
Annex A (informative) Typical diagram of an equipment . 16

60358-2 © IEC:2013 – 3 –
Annex AA (informative) High-frequency characteristics of coupling capacitors for
power line carrier circuits . 17
Bibliography . 19

Figure A.200.1 – Example of a diagram for a coupling capacitor with carrier-frequency
accessories (see IEC 60481) . 16
Figure AA.1 – Wiring diagram of the measuring circuit for the high-frequency
capacitance and equivalent series resistance of a coupling capacitor . 18
Figure AA.2 – Relation between length and capacitance where capacitive deviation –
20 % to +50 % can be fulfilled up to 500 kHz . 18

Table 200 – Limits of temperature rise of windings. 14

– 4 – 60358-2 © IEC:2013
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
COUPLING CAPACITORS AND CAPACITOR DIVIDERS –

Part 2: AC or DC single-phase coupling capacitor connected between
line and ground for power line carrier-frequency (PLC) application

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60358-2 has been prepared by IEC technical committee 33: Power
capacitors and their applications.
The text of this standard is based on the following documents:
FDIS Report on voting
33/531/FDIS 33/537/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts in the IEC 60358 series, published under the general title Coupling
capacitors and capacitor dividers, can be found on the IEC website.

60358-2 © IEC:2013 – 5 –
This International Standard is to be used in conjunction with the latest edition of IEC 60358-1
and its amendments. It was established on the basis of the first edition (2012) of that
standard.
This Part 2 supplements or modifies the corresponding clauses in IEC 60358-1.
When a particular subclause of Part 1 is not mentioned in this Part 2, that subclause applies
as far as is reasonable. Where this Part 2 states “addition” or “replacement”, the relevant text
in Part 1 is to be adapted accordingly.
For additional clauses, subclauses, figures, tables or annexes, the following numbering
system is used:
– subclauses, tables and figures which are additional to those in Part 1 are numbered
starting from 200;
– additional annexes are lettered AA, BB etc.
– as the notes are integrated into the clauses, their numbering starts from 1 as usual.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
– 6 – 60358-2 © IEC:2013
INTRODUCTION
This series consists of the following parts:
IEC 60358-1, Coupling capacitors and capacitor dividers – Part 1: General rules
IEC 60358-2, Coupling capacitors and capacitor dividers – Part 2: AC or DC single-phase
coupling capacitor connected between line and ground for power line
carrier-frequency (PLC) application
IEC 60358-3 , Coupling capacitors and capacitor dividers – Part 3: AC or DC single-phase
coupling capacitor connected between line and ground for harmonic-filters
applications
IEC 60358-4 , Coupling capacitors and capacitor dividers – Part 4: AC or DC single-phase
capacitor-divider and RC-divider connected between line and ground
(except for CVT’s which belong to IEC 61869 series)

—————————
Under consideration.
Under consideration.
60358-2 © IEC:2013 – 7 –
COUPLING CAPACITORS AND CAPACITOR DIVIDERS –

Part 2: AC or DC single-phase coupling capacitor connected between
line and ground for power line carrier-frequency (PLC) application

1 Scope
Clause 1 of IEC 60358-1:2012 is applicable with the following additions:
This part of the IEC 60358 series applies to AC or DC single-phase coupling capacitors, with
rated voltage > 1 000 V, connected between line and ground with a low voltage terminal either
permanently earthed or connected to a device for power line carrier-frequency (PLC)
applications at frequencies from 30 kHz to 500 kHz or similar applications (DC or AC) at
power frequencies from 15 Hz to 60 Hz.
The transmission requirements for coupling devices for power line carrier (PLC) systems are
defined in IEC 60481.
NOTE Diagrams of coupling capacitors to which this standard applies are given in Figure A.1.
2 Normative references
Clause 2 of IEC 60358-1:2012 is replaced by the following:
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 60060-1, High-voltage test techniques – Part 1: General definitions and test requirements
IEC 60060-2, High-voltage test techniques – Part 2: Measuring systems
IEC 60358-1:2012, Coupling capacitors and capacitor dividers. – Part 1: General rules
IEC 60481, Coupling devices for power line carrier systems
IEC 61869-5, Instrument transformers – Part 5: Additional requirements for capacitor voltage
transformers
3 Terms and definitions
Clause 3 of IEC 603
...