iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 12847:2003

(Main)

Bitumen and bituminous binders - Determination of settling tendency of bitumen emulsions

Bitumen and bituminous binders - Determination of settling tendency of bitumen emulsions

This European Standard specifies a method for the determination of the settling tendency of bitumen emulsions.
NOTE 1   This test method is not applicable for emulsions having a low viscosity.
NOTE 2   For the purposes of this European Standard, the term "% (m/m)" is used to represent the mass fraction.
WARNING - The use of this standard can involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Bitumen und bitumenhaltige Bindemittel - Bestimmung des Absetzverhaltens von Bitumenemulsionen

Diese Europäische Norm legt ein Verfahren zur Bestimmung des Absetzverhaltens von Bitumenemulsionen fest.

Bitumes et liants bitumineux - Détermination de la tendance a la décantation des émulsions de bitume

Domaine d'application
Cette Norme européenne prescrit une méthode pour la détermination de la tendance à la décantation des émulsions de bitume.
NOTE 1   Cette méthode n'est pas applicable pour les émulsions de faible viscosité.
NOTE 2   Pour les besoins de la présente Norme européenne, le terme « % (m/m) » est utilisé pour représenter la fraction massique.
AVERTISSEMENT   L'utilisation de la présente Norme européenne implique l'intervention de produits, d'opérations et d'équipements à caractère dangereux. La présente Norme européenne n'a pas la prétention d'aborder tous les problèmes de sécurité concernés par son usage. Il est de la responsabilité de l'utilisateur de consulter et d'établir des règles de sécurité et d'hygiène appropriées et de déterminer l'applicabilité des restrictions réglementaires avant utilisation.

Bitumen in bitumenska veziva - Določevanje časa obstojnosti bitumenskih emulzij

General Information

Status
Withdrawn
Publication Date
31-Dec-2002
Withdrawal Date
25-May-2009
ICS
75.140 - Waxes, bituminous materials and other petroleum products
91.100.50 - Binders. Sealing materials
Technical Committee
VLA - Water proofing
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
25-May-2009
Due Date
17-Jun-2009
Completion Date
26-May-2009
Ref Project
EN 12847:2002 - Bitumen and bituminous binders - Determination of settling tendency of bitumen emulsions

Relations

Replaced By
SIST EN 12847:2009 - Bitumen and bituminous binders - Determination of settling tendency of bituminous emulsions
Effective Date
01-Jul-2009

Buy Standard

EN 12847:2003EN 12847:2003
PreviousNext
Standard
EN 12847:2003
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bitumen und bitumenhaltige Bindemittel - Bestimmung des Absetzverhaltens von BitumenemulsionenBitumes et liants bitumineux - Détermination de la tendance a la décantation des émulsions de bitumeBitumen and bituminous binders - Determination of settling tendency of bitumen emulsions91.100.50Veziva. Tesnilni materialiBinders. Sealing materials75.140Voski, bitumni in drugi naftni proizvodiWaxes, bituminous materials and other petroleum productsICS:Ta slovenski standard je istoveten z:EN 12847:2002SIST EN 12847:2003en01-januar-2003SIST EN 12847:2003SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12847May 2002ICS 75.140; 91.100.50English versionBitumen and bituminous binders - Determination of settlingtendency of bitumen emulsionsBitumes et liants bitumineux - Détermination de la tendanceà la décantation des émulsions de bitumeBitumen und bitumenhaltige Bindemittel - Bestimmung desAbsetzverhaltens von BitumenemulsionenThis European Standard was approved by CEN on 15 February 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12847:2002 ESIST EN 12847:2003
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 12594:2025(Main)
Bitumen and bituminous binders - Preparation of test samples
EN 12594:2024

This document specifies methods for preparing test samples of bitumens and bituminous binders in order to test their properties.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12597:2025(Main)
Bitumen and bituminous binders - Terminology
EN 12597:2024

This European Standard defines terms for paving or industrial bitumen of various types and binders derived from bitumen.
This European Standard is intended to cover materials only within the scope of CEN/TC 336, i.e. only bitumens and bituminous binders. It should consequently not extend to non-petroleum "hydrocarbon" binders such as coal tar and its derivatives or to natural asphalts. However, some definitions are given for some excluded materials and related terms. The corresponding terms were introduced only when they appeared in a definition of a product or process and when their definition was found necessary for understanding or for avoiding any ambiguity.

  • Standard
    33 pages
    English, French and German language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CEN/TR 18114:2025(Main)
Bitumens and bituminous binders - Sustainability - Review on how to address environmental information
CEN/TR 18114:2024

This document provides an overview of:
-   current requirements in the European Union and in individual European states to address sustainability in the field of construction works where bitumens and bituminous binders are used;
-   the requirements of the Construction Products Regulation (CPR) on environmental sustainability and analyses the implications for bitumens and bituminous binders;
-   existing horizontal standard EN 15804:2012+A2:2019 related to core rules for the product category of construction products and assesses if it can be used without any additional documents for bitumen and bituminous binders;
-   status of draft standards developed for specific complementary product category rules by CEN/TC 154, CEN/TC 227, CEN/TC 254 and any other relevant TCs, and assesses if these drafts could require any additional documents specific for bitumens and bituminous binders;
-   other relevant documents.
This document is intended to provide support to CEN/TC 336 for assessing the need for any further standardization documents covering specific product category rules for bitumens and bituminous binders or for other standardization documents in the field of environmental sustainability of bituminous binders.
This document covers bitumens and bituminous binders as described in EN 12597, including cut-back and fluxed bituminous binder, and bitumen emulsion, as used in construction works.

  • Technical report
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12607-1:2025(Main)
Bitumen and bituminous binders - Determination of the resistance to hardening under influence of heat and air - Part 1: RTFOT method
EN 12607-1:2024

This document specifies a method for the conditioning of bitumen or bituminous binders in order to provide for measuring the combined effects of heat and air on a thin moving film of bitumen or bituminous binder simulating the hardening which most bituminous binders undergo during mixing in an asphalt mixing plant. The method is referred to as RTFOT - Rolling Thin Film Oven Test.
The method described is applicable to paving grade bitumen. The method described is also applicable to other bituminous binders considering that the reference temperature can result in excessive hardening that does not resemble real conditions during mixing at the plant. It is possible that the method does not represent the hardening that occurs during mixing bitumen used for warm mix asphalt.
The method described is not applicable to those binders having a viscosity at the tested temperature not allowing to provide a moving film. In some cases, it is possible that the test sample creeps out of the glass container and flows on the heating elements of the oven during testing.
The method described is not applicable to binders with volatiles components present. In case of cutback bitumen or bituminous emulsion, the described procedure is only applicable after being stabilized, e.g. in accordance with EN 13074-2 [9].
WARNING - Use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to identify the hazards and assess the risks involved in performing this test method and to implement sufficient control measures to protect individual operators (and the environment). This includes appropriate safety and health practices and determination of the applicability of regulatory limitations prior to use.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1426:2025(Main)
Bitumen and bituminous binders - Determination of needle penetration
EN 1426:2024

This document specifies a method for the determination of the needle penetration of bitumens and bituminous binders.
The standard procedure for the determination of the needle penetration (consistency) is described for penetrations up to (330 × 0,1) mm at a temperature of 25 °C. The method also allows for penetrations up to (500 × 0,1) mm using a longer needle.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 16346:2024(Main)
Bitumen and bituminous binders - Determination of breaking behaviour and immediate adhesivity of cationic bituminous emulsions
EN 16346:2023

This document specifies a method for the determination of the breaking and immediate adhesivity behaviour of cationic bituminous emulsions in contact with aggregate. The method applies to emulsions used for surface dressing and similar applications and can be used for formulation as well as for production control purposes.
WARNING — The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14770:2023(Main)
Bitumen and bituminous binders - Determination of complex shear modulus and phase angle - Dynamic Shear Rheometer (DSR)
EN 14770:2023

This document specifies a general method of using a dynamic shear rheometer (DSR) for measuring the rheological properties of bituminous binders. The procedure involves determining the complex shear modulus and phase angle of binders over a range of test frequencies and test temperatures when tested in oscillatory shear.
From the test, the complex shear modulus, |G*|, and its phase angle, δ, at a given temperature and frequency are calculated, as well as the components G' and G" of the complex shear modulus.
This method is applicable to un-aged, aged, stabilized and recovered bituminous binders. The test procedure in accordance with this document is not applicable for bituminous binders with particles larger than 250 μm (e.g. filler material, granulated rubber).
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14769:2023(Main)
Bitumen and bituminous binders - Accelerated long-term ageing conditioning by a Pressure Ageing Vessel (PAV)
EN 14769:2023

This document specifies an accelerated long-term ageing/conditioning procedure for bituminous binders. The procedure involves ageing trays of binder at elevated temperatures under pressurized conditions in a pressure ageing vessel (PAV).
NOTE   For binders to be used in hot and warm asphalt applications, the pre-conditioning of the sample can be performed using one of the methods in the EN 12607 series. For binders to be used in bituminous emulsion and cut back or fluxed applications, the stabilization of the sample is such that there are no volatiles remaining.
WARNING - The use of this document can involve hazardous materials, operations and equipment, in particular, the use of a high pressure ageing vessel. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate health and safety practices and determine the applicability of regulatory limitations prior to use. If there is the likelihood of volatile components being present in a binder, this procedure is not used.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14771:2023(Main)
Bitumen and bituminous binders - Determination of the flexural creep stiffness - Bending Beam Rheometer (BBR)
EN 14771:2023

This document specifies a method for the determination of the flexural creep stiffness of bitumen and bituminous binders in the range of 30 MPa to 1 GPa by means of the bending beam rheometer.
The method can be applied to a variety of bitumens, including unmodified as well as modified binders, as fresh (unused) binders, as well as binders after laboratory ageing conditioning (e.g. EN 12607-1, EN 14769), and also binders that have been recovered from asphalt mixtures.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12595:2023(Main)
Bitumen and bituminous binders - Determination of kinematic viscosity
EN 12595:2023

This document specifies a method for the determination of the kinematic viscosity of bituminous binders at 60 °C and 135 °C, in a range from 6 mm2/s to 300 000 mm2/s. Other temperatures are possible if calibration constants are known. Bituminous emulsions are not covered within the scope of this method.
Results for this method can be used to calculate dynamic viscosity when the density of the test material is known or can be determined.
NOTE   This document assumes Newtonian behaviour of the sample at test conditions.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to identify the hazards and assess the risks involved in performing this test method and to implement sufficient control measures to protect individual operators (and the environment). This includes appropriate safety and health practices and determination of the applicability of regulatory limitations prior to use.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day