Abstract

This sheet of IEC 60674-3 (all sheets) [3] gives the requirements for biaxially oriented polypropylene film having a smooth or rough surface, corona treated when required for vacuum metallization. The films are for use as dielectric in capacitors.
Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application is based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.
Safety warning: It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner.

Status
Published
Public Enquiry End Date
30-Nov-2025
Publication Date
18-Nov-2026
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
17-Nov-2026
Due Date
22-Jan-2027
Completion Date
19-Nov-2026

Buy Documents

Standard

SIST EN IEC 60674-3-1:2027

English language (16 pages)
Preview
Preview
e-Library read for
×1 day

SIST EN IEC 60674-3-1:2027 is an IEC specification for biaxially oriented polypropylene (PP) films for capacitors, published through SIST. It sets requirements for films with smooth or rough surfaces, including corona-treated grades when vacuum metallization is needed, and it is intended for films used as dielectric in capacitors.

What does SIST EN IEC 60674-3-1 specify?

SIST EN IEC 60674-3-1:2027 specifies the requirements for biaxially oriented polypropylene film for capacitor use. It covers smooth-surface films, rough-surface films, and grades that are pre-treated on one or both sides for vacuum deposition of metal.

The document is organized into clauses on scope, normative references, classification, designation, general requirements, dimensions, properties, and roll characteristics, followed by a bibliography. Its main technical content is concentrated in clauses 4 to 9 and Tables 1 to 4.

What are the key requirements of SIST EN IEC 60674-3-1?

SIST EN IEC 60674-3-1 focuses on material type, dimensions, electrical performance, and roll quality. In practice, it gives buyers and manufacturers a common way to specify PP film grades and verify whether a supplied roll is suitable for capacitor production.

Material and classification

Clause 4 divides the film into three main types:

  • Type 1 - smooth surface, with subtypes for untreated film and film pre-treated on one or both sides.
  • Type 2 - at least one rough surface, with the same pre-treatment options.
  • Type 3 - thin film with high electric strength, again with untreated and pre-treated variants.

Clause 6 requires the material to be made essentially from isotactic polypropylene homopolymer and to comply with IEC 60674-1. This matters because the base polymer and general requirements affect electrical behavior and consistency from batch to batch.

Identification and dimensions

Clause 5 gives the designation format: film reference, IEC 60674-3-1, PP, type, thickness, width, and length. That helps users order the exact construction they need and avoid confusion between surface state, treatment, and size.

Clause 7 sets the dimensional rules. Thickness is measured using IEC 60674-2, and the document gives preferred gravimetric thicknesses for each type rather than a general thickness limit. Width is also measured to IEC 60674-2, with tolerance rules depending on width range, while length and roll diameter are left to the purchase contract.

Physical and electrical properties

Clause 8 and Table 1 specify key physical properties such as density, melting point, tensile strength, elongation at break, surface resistivity, volume resistivity, dissipation factor, relative permittivity, and dimensional change for shrinkage. These are the core checks for whether the film behaves as an insulating dielectric rather than a generic plastic sheet.

Electric strength is covered in 8.2 and Table 2. The test uses IEC 60674-2, with values set by thickness, type, and test temperature. Electrical weak spots are covered in 8.3 and Table 3, which allows compliance by either of two test methods. For users, this means the film is judged not only by average strength but also by local defects that can cause capacitor failure.

Surface treatment, impregnation, and roll quality

Clause 8.5 applies wetting tension requirements to the pre-treated grades, which matters when the film will be vacuum metallized. Clauses 8.6 to 8.8 deal with liquid absorption, compatibility with impregnants, and dissipation factor under impregnated conditions, but these are to be agreed between supplier and purchaser where needed.

Clause 9 covers roll characteristics. It includes windability, joins, roll width, core size, and labeling. Table 4 limits the number of joins according to thickness, roll width, and core diameter, and clause 9.5 requires the pre-treated side to be identified.

Who uses SIST EN IEC 60674-3-1?

SIST EN IEC 60674-3-1 is used by capacitor manufacturers, materials engineers, quality control laboratories, and buyers of electrical insulating film. It supports material selection, incoming inspection, supplier qualification, and product specification for capacitor dielectric films.

It is also relevant to organizations testing film properties against IEC methods, especially where roll construction, metallization readiness, and electrical performance must be documented.

What changed in SIST EN IEC 60674-3-1 from the previous edition?

SIST EN IEC 60674-3-1 is the third edition. It cancels and replaces the second edition and its amendments, and the foreword states that it is a technical revision.

The stated changes are that the document was completely revised editorially and technically, it was included in the IEC 60674 series of standards, and the test methods were updated to reflect the current state of the art.

Which standards are used with SIST EN IEC 60674-3-1?

SIST EN IEC 60674-3-1 uses IEC 60674-1 for definitions and general requirements, and IEC 60674-2 for the test methods used throughout the specification. These two companion parts are the main framework behind the document.

It also cites ISO 1183-2:2019 for density and ISO 11357-3:2018 for melting point. The wider IEC 60674 series is identified in the introduction as Part 1 on definitions and general requirements, Part 2 on methods of test, and Part 3 on specifications for individual materials.

What does the SIST EN IEC 60674-3-1 document contain?

SIST EN IEC 60674-3-1 contains four technical tables that support specification and testing. Table 1 covers physical properties, Table 2 gives electric strength values for DC testing, Table 3 sets limits for electrical weak spots, and Table 4 limits joins in rolls.

The clauses also describe how to measure thickness, width, space factor, windability, and roll width, and how to judge pre-treated surfaces and joins. In practice, the document is used for specification writing, product approval, laboratory testing, and roll inspection before capacitor manufacture.

Relations

Effective Date
01-Jan-2027
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026

Buy Documents

Standard

SIST EN IEC 60674-3-1:2027

English language (16 pages)
Preview
Preview
e-Library read for
×1 day

Get Certified

Connect with accredited certification bodies for this standard

DIN CERTCO

DIN Group product certification.

DAKKS Germany Verified

IMQ S.p.A. (Certification)

Italian electrical product certification.

ACCREDIA Italy Verified

SLG Prüf- und Zertifizierungs GmbH

German testing and certification body.

DAKKS Germany Verified

Sponsored listings

Frequently Asked Questions

SIST EN IEC 60674-3-1:2027 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 1: Biaxially oriented polypropylene (PP) films for capacitors (IEC 60674-3-1:2026)". This standard covers: This sheet of IEC 60674-3 (all sheets) [3] gives the requirements for biaxially oriented polypropylene film having a smooth or rough surface, corona treated when required for vacuum metallization. The films are for use as dielectric in capacitors. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application is based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. Safety warning: It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner.

This sheet of IEC 60674-3 (all sheets) [3] gives the requirements for biaxially oriented polypropylene film having a smooth or rough surface, corona treated when required for vacuum metallization. The films are for use as dielectric in capacitors. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application is based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. Safety warning: It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner.

SIST EN IEC 60674-3-1:2027 is classified under the following ICS (International Classification for Standards) categories: 29.035.20 - Plastics and rubber insulating materials; 83.140.10 - Films and sheets. The ICS classification helps identify the subject area and facilitates finding related standards.

SIST EN IEC 60674-3-1:2027 has the following relationships with other standards: It is inter standard links to SIST EN IEC 60674-3-1:2021, SIST EN 60674-2:2017, SIST EN 60674-1:2001. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

SIST EN IEC 60674-3-1:2027 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


SLOVENSKI STANDARD
01-januar-2027
Nadomešča:
SIST EN IEC 60674-3-1:2021
Plastične folije za električne namene - 3. del: Specifikacije za posamezne materiale
- 1. list: Dvoosno orientirane polipropilenske folije za kondenzatorje (IEC 60674-3-
1:2026)
Plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet
1: Biaxially oriented polypropylene (PP) films for capacitors (IEC 60674-3-1:2026)
Isolierfolien für elektrotechnische Zwecke –Teil 3: Anforderungen für einzelne Werkstoffe
– Blatt 1: Biaxial orientierte Polypropylen-(PP)-Folien für Kondensatoren (IEC 60674-3-
1:2026)
Films plastiques à usages électriques - Partie 3: Spécifications pour matériaux
particuliers - Feuille 1: Films de polypropylène biorienté (PP) pour condensateurs (IEC
60674-3-1:2026)
Ta slovenski standard je istoveten z: EN IEC 60674-3-1:2026
ICS:
29.035.20 Plastični in gumeni izolacijski Plastics and rubber insulating
materiali materials
83.140.10 Filmi in folije Films and sheets
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 60674-3-1

NORME EUROPÉENNE
EUROPÄISCHE NORM November 2026
ICS 29.035.20 Supersedes EN IEC 60674-3-1:2021
English Version
Plastic films for electrical purposes - Part 3: Specifications for
individual materials - Sheet 1: Biaxially oriented polypropylene
(PP) films for capacitors
(IEC 60674-3-1:2026)
Films plastiques à usages électriques - Partie 3: Isolierfolien für elektrotechnische Zwecke - Teil 3:
Spécifications pour matériaux particuliers - Feuille 1: Films Anforderungen für einzelne Werkstoffe - Blatt 1: Biaxial
de polypropylène biorienté (PP) pour condensateurs orientierte Polypropylen-(PP)-Folien für Kondensatoren
(IEC 60674-3-1:2026) (IEC 60674-3-1:2026)
This European Standard was approved by CENELEC on 2026-11-05. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60674-3-1:2026 E

European foreword
The text of document 15/1097/FDIS, future edition 3 of IEC 60674-3-1, prepared by TC 15 "Solid
electrical insulating materials" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 60674-3-1:2026.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2027-11-30
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2029-11-30
document have to be withdrawn
This document supersedes EN IEC 60674-3-1:2021 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60674-3-1:2026 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 60674-1 NOTE Approved as EN 60674-1
IEC 60674-2 NOTE Approved as EN 60674-2
IEC 60674-3 (series) NOTE Approved as EN 60674-3-8:2011/A1 (series)
IEC 60674-2:2016 NOTE Approved as EN 60674-2:2017 (not modified)
IEC 60674-1:1980 NOTE Approved as EN 60674-1:1998 (not modified)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60674-1 1980 Specification for plastic films for electrical EN 60674-1 1998
purposes. Part 1: Definitions and general
requirements
IEC 60674-2 2016 Specification for plastic films for electrical EN 60674-2 2017
purposes - Part 2: Methods of test
IEC 60674-1 - Specification for plastic films for electrical EN 60674-1 -
purposes. Part 1: Definitions and general
requirements
IEC 60674-2 - Specification for plastic films for electrical EN 60674-2 -
purposes - Part 2: Methods of test

IEC 60674-3-1 ®
Edition 3.0 2026-10
INTERNATIONAL
STANDARD
Plastic films for electrical purposes -
Part 3: Specifications for individual materials - Sheet 1: Biaxially oriented
polypropylene (PP) films for capacitors
ICS 29.035.20  ISBN 978-2-8327-1516-1

IEC 60674-3-1:2026-10(en)
IEC 60674-3-1:2026 © IEC 2026
CONTENTS
FOREWORD . 2
INTRODUCTION . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Classification . 5
5 Designation . 6
6 General requirements . 6
7 Dimensions . 6
7.1 Thickness . 6
7.2 Width . 7
7.3 Length/diameter . 7
8 Properties . 7
8.1 Physical properties . 7
8.2 Electric strength (DC test) . 8
8.3 Electrical weak spots . 8
8.4 Thermal endurance . 9
8.5 Wetting tension (types 1b + 1c, 2b + 2c and 3b + 3c only) . 9
8.6 Liquid absorption . 9
8.7 Compatibility with impregnants. 10
8.8 Dissipation factor under impregnated conditions . 10
8.9 Space factor . 10
9 Roll characteristics . 10
9.1 Windability . 10
9.2 Joins . 10
9.3 Roll width (overall width) . 11
9.4 Core . 11
9.5 Labelling . 11
Bibliography . 12

Table 1 – Physical properties . 7
Table 2 – Electric strength (DC test) for types 1, 2 and 3 . 8
Table 3 – Electrical weak spots for types 1, 2 and 3 . 9
Table 4 – Maximum number of joins within a roll (types 1, 2 and 3) . 11

IEC 60674-3-1:2026 © IEC 2026
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
Plastic films for electrical purposes -
Part 3: Specifications for individual materials - Sheet 1: Biaxially oriented
polypropylene (PP) films for capacitors

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of a patent.
IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in respect
thereof. As of the date of publication of this document, IEC had not received notice of a patent, which may be
required to implement this document. However, implementers are cautioned that this may not represent the latest
information, which may be obtained from the patent database available at https://patents.iec.ch. IEC shall not be
held responsible for identifying any or all such patent rights.
IEC 60674-3-1 has been prepared by IEC technical committee 15: Solid electrical insulating
materials. It is an International Standard.
This third edition cancels and replaces the second edition published in 2021. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) this document has been completely revised editorially and technically;
b) the ranges of film thickness have been expanded;
c) the requirements of characteristics with the films of expanded thickness have been added.
The text of this International Standard is based on the following documents:
IEC 60674-3-1:2026 © IEC 2026
Draft Report on voting
15/1097/FDIS 15/1106/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
This document was dra
...