Abstract

This sheet of IEC 60674-3 (all sheets) [3] gives the requirements for biaxially oriented polypropylene film having a smooth or rough surface, corona treated when required for vacuum metallization. The films are for use as dielectric in capacitors.
Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application is based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.
Safety warning: It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner.

Status
Published
Publication Date
12-Nov-2026
Current Stage
6060 - Document made available - Publishing
Start Date
13-Nov-2026
Due Date
30-Sep-2026
Completion Date
13-Nov-2026

Buy Documents

Standard

EN IEC 60674-3-1:2027

English language (16 pages)
Preview
Preview
e-Library read for
×1 day

EN IEC 60674-3-1:2026 is a CLC electrotechnical standard for biaxially oriented polypropylene (PP) films for capacitors. It specifies the material classification, dimensions, electrical properties and roll characteristics for PP dielectric films used in capacitor construction, and it points users to IEC 60674-1 and IEC 60674-2 for the general rules and test methods.

What does EN IEC 60674-3-1:2026 specify?

EN IEC 60674-3-1:2026 covers biaxially oriented polypropylene film with a smooth or rough surface, including films that are corona treated when needed for vacuum metallization. The document is for films used as dielectric in capacitors, so it is aimed at material suppliers, capacitor manufacturers and test laboratories.

The standard is organized into a foreword, introduction, clauses 1 to 9, and a bibliography. Clause 4 classifies the film types, clause 5 gives the designation format, clauses 6 to 8 cover requirements, and clause 9 covers roll characteristics.

What are the key requirements of EN IEC 60674-3-1:2026?

Material type, surface condition and designation

Clause 4 divides the film into three main types: smooth-surface film, rough-surface film, and thin film with high electric strength. Each type also has subtypes for untreated film and for one-side or both-sides pre-treated film for vacuum deposition of metal.

Clause 5 gives the identification format for ordering and marking. In practice, buyers and suppliers need to state the standard reference, PP, the type, thickness, width and length so the film can be matched to the intended capacitor process.

General material and dimensional requirements

Clause 6 requires the film to be made essentially from isotactic polypropylene homopolymer and to comply with the general requirements of IEC 60674-1. This matters because the film is not just a generic polypropylene sheet - it is intended to meet the electrical and handling expectations of the series.

Clause 7 covers thickness, width and length or diameter. Thickness is measured using the test methods in IEC 60674-2, width is measured by the same test standard, and the document leaves length and roll diameter to the purchase contract. For users, this means thickness and width control are specified, while roll length and diameter must be agreed commercially.

Physical and electrical properties

Clause 8.1 points to the required physical properties in Table 1, including density, melting point, tensile strength, elongation at break, surface and volume resistivity, dissipation factor, relative permittivity and dimensional change for shrinkage. These are the core material checks for confirming that the film behaves as expected in processing and in service.

Clause 8.2 sets the DC electric strength requirements, including a higher-temperature test condition for thin film. Clause 8.3 covers electrical weak spots and allows compliance through either of two counting methods. In practice, these clauses are the main screening tests for dielectric quality and defect control.

Surface treatment, impregnation and roll quality

Clause 8.5 applies wetting tension requirements only to the pre-treated film types. Clauses 8.6 to 8.8 deal with liquid absorption, compatibility with impregnants and dissipation factor under impregnated conditions, but they leave the exact limits and methods to agreement between supplier and purchaser. That is important because capacitor impregnants vary widely.

Clause 8.9 introduces space factor, which links surface roughness to the increase in bulking thickness over gravimetric thickness. Clause 9 then covers windability, joins, roll width, cores and labelling. These requirements matter for converting the film into rolls that can run through capacitor winding equipment without damage or excessive defects.

What terms does EN IEC 60674-3-1:2026 use?

  • PP - Polypropylene, the base polymer used for the film.
  • Corona treated - Surface treatment used when the film needs better adhesion for vacuum metallization.
  • Vacuum metallization - A process for depositing metal on the film surface to form capacitor electrodes.
  • Space factor - The percentage increase in bulking thickness over gravimetric thickness, used to distinguish rough-surface film from smooth-surface film.
  • Impregnants - The dielectric fluids used with impregnated capacitors, which may affect absorption, compatibility and loss behavior.
  • DSC - Differential scanning calorimetry, the method cited for measuring melting point in the physical properties table.
  • Wetting tension - A surface property used to check the suitability of pre-treated film surfaces.

Who uses EN IEC 60674-3-1:2026?

EN IEC 60674-3-1:2026 is used by capacitor manufacturers, film suppliers, quality control laboratories and purchasing teams that specify dielectric film for capacitors. It is also relevant to test laboratories that measure electrical strength, weak spots, resistivity, shrinkage and roll characteristics. In practice, it supports product selection, incoming inspection, supplier qualification and contract specification.

What changed in EN IEC 60674-3-1:2026 from the previous edition?

The foreword says this third edition cancels and replaces the second edition and its two amendments. It also states that the document has been completely revised editorially and technically, that it has been included in the IEC 60674 series, and that the test methods have been updated to reflect the current state of the art.

Which standards are used with EN IEC 60674-3-1:2026?

  • IEC 60674-1:1980 - Provides the definitions and general requirements that this sheet builds on.
  • IEC 60674-2:2016 - Provides the test methods used throughout the document for thickness, width, electrical tests, windability and other measurements.
  • ISO 1183-2:2019 - The density method cited in Table 1 for density measurement.
  • ISO 11357-3:2018 - The DSC method cited in Table 1 for melting point measurement.

What does the EN IEC 60674-3-1:2026 document contain?

The document contains a classification system for film types, a designation format, and a set of property requirements tied to test methods from IEC 60674-2. It includes Table 1 for physical properties, Table 2 for DC electric strength, Table 3 for electrical weak spots, and Table 4 for the maximum number of joins in a roll. It also gives the procedures or references for thickness measurement, wetting tension, windability, roll-width control, core preferences and labelling of pre-treated film.

For design and procurement work, the most useful parts are the type classification, the designation format and the clauses that set the property checks. For testing work, the key content is the combination of IEC 60674-2 methods with the acceptance limits stated in the tables and clauses.

Relations

Effective Date
21-Jan-2025
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026

Buy Documents

Standard

EN IEC 60674-3-1:2027

English language (16 pages)
Preview
Preview
e-Library read for
×1 day

Get Certified

Connect with accredited certification bodies for this standard

IMQ S.p.A. (Certification)

Italian electrical product certification.

ACCREDIA Italy Verified

SLG Prüf- und Zertifizierungs GmbH

German testing and certification body.

DAKKS Germany Verified

UL Solutions

Global safety science company with testing, inspection and certification.

ANAB United States Verified

Sponsored listings

Frequently Asked Questions

EN IEC 60674-3-1:2026 is a standard published by CLC. Its full title is "Plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 1: Biaxially oriented polypropylene (PP) films for capacitors". This standard covers: This sheet of IEC 60674-3 (all sheets) [3] gives the requirements for biaxially oriented polypropylene film having a smooth or rough surface, corona treated when required for vacuum metallization. The films are for use as dielectric in capacitors. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application is based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. Safety warning: It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner.

This sheet of IEC 60674-3 (all sheets) [3] gives the requirements for biaxially oriented polypropylene film having a smooth or rough surface, corona treated when required for vacuum metallization. The films are for use as dielectric in capacitors. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application is based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. Safety warning: It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in a safe manner.

EN IEC 60674-3-1:2026 is classified under the following ICS (International Classification for Standards) categories: 29.035.20 - Plastics and rubber insulating materials. The ICS classification helps identify the subject area and facilitates finding related standards.

EN IEC 60674-3-1:2026 has the following relationships with other standards: It is inter standard links to EN IEC 60674-3-1:2021, EN 60674-1:1998, EN 60674-2:2017. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

EN IEC 60674-3-1:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


SLOVENSKI STANDARD
01-januar-2027
Nadomešča:
SIST EN IEC 60674-3-1:2021
Plastične folije za električne namene - 3. del: Specifikacije za posamezne materiale
- 1. list: Dvoosno orientirane polipropilenske folije za kondenzatorje (IEC 60674-3-
1:2026)
Plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet
1: Biaxially oriented polypropylene (PP) films for capacitors (IEC 60674-3-1:2026)
Isolierfolien für elektrotechnische Zwecke –Teil 3: Anforderungen für einzelne Werkstoffe
– Blatt 1: Biaxial orientierte Polypropylen-(PP)-Folien für Kondensatoren (IEC 60674-3-
1:2026)
Films plastiques à usages électriques - Partie 3: Spécifications pour matériaux
particuliers - Feuille 1: Films de polypropylène biorienté (PP) pour condensateurs (IEC
60674-3-1:2026)
Ta slovenski standard je istoveten z: EN IEC 60674-3-1:2026
ICS:
29.035.20 Plastični in gumeni izolacijski Plastics and rubber insulating
materiali materials
83.140.10 Filmi in folije Films and sheets
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 60674-3-1

NORME EUROPÉENNE
EUROPÄISCHE NORM November 2026
ICS 29.035.20 Supersedes EN IEC 60674-3-1:2021
English Version
Plastic films for electrical purposes - Part 3: Specifications for
individual materials - Sheet 1: Biaxially oriented polypropylene
(PP) films for capacitors
(IEC 60674-3-1:2026)
Films plastiques à usages électriques - Partie 3: Isolierfolien für elektrotechnische Zwecke - Teil 3:
Spécifications pour matériaux particuliers - Feuille 1: Films Anforderungen für einzelne Werkstoffe - Blatt 1: Biaxial
de polypropylène biorienté (PP) pour condensateurs orientierte Polypropylen-(PP)-Folien für Kondensatoren
(IEC 60674-3-1:2026) (IEC 60674-3-1:2026)
This European Standard was approved by CENELEC on 2026-11-05. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60674-3-1:2026 E

European foreword
The text of document 15/1097/FDIS, future edition 3 of IEC 60674-3-1, prepared by TC 15 "Solid
electrical insulating materials" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN IEC 60674-3-1:2026.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2027-11-30
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2029-11-30
document have to be withdrawn
This document supersedes EN IEC 60674-3-1:2021 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60674-3-1:2026 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 60674-1 NOTE Approved as EN 60674-1
IEC 60674-2 NOTE Approved as EN 60674-2
IEC 60674-3 (series) NOTE Approved as EN 60674-3-8:2011/A1 (series)
IEC 60674-2:2016 NOTE Approved as EN 60674-2:2017 (not modified)
IEC 60674-1:1980 NOTE Approved as EN 60674-1:1998 (not modified)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60674-1 1980 Specification for plastic films for electrical EN 60674-1 1998
purposes. Part 1: Definitions and general
requirements
IEC 60674-2 2016 Specification for plastic films for electrical EN 60674-2 2017
purposes - Part 2: Methods of test
IEC 60674-1 - Specification for plastic films for electrical EN 60674-1 -
purposes. Part 1: Definitions and general
requirements
IEC 60674-2 - Specification for plastic films for electrical EN 60674-2 -
purposes - Part 2: Methods of test

IEC 60674-3-1 ®
Edition 3.0 2026-10
INTERNATIONAL
STANDARD
Plastic films for electrical purposes -
Part 3: Specifications for individual materials - Sheet 1: Biaxially oriented
polypropylene (PP) films for capacitors
ICS 29.035.20  ISBN 978-2-8327-1516-1

IEC 60674-3-1:2026-10(en)
IEC 60674-3-1:2026 © IEC 2026
CONTENTS
FOREWORD . 2
INTRODUCTION . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Classification . 5
5 Designation . 6
6 General requirements . 6
7 Dimensions . 6
7.1 Thickness . 6
7.2 Width . 7
7.3 Length/diameter . 7
8 Properties . 7
8.1 Physical properties . 7
8.2 Electric strength (DC test) . 8
8.3 Electrical weak spots . 8
8.4 Thermal endurance . 9
8.5 Wetting tension (types 1b + 1c, 2b + 2c and 3b + 3c only) . 9
8.6 Liquid absorption . 9
8.7 Compatibility with impregnants. 10
8.8 Dissipation factor under impregnated conditions . 10
8.9 Space factor . 10
9 Roll characteristics . 10
9.1 Windability . 10
9.2 Joins . 10
9.3 Roll width (overall width) . 11
9.4 Core . 11
9.5 Labelling . 11
Bibliography . 12

Table 1 – Physical properties . 7
Table 2 – Electric strength (DC test) for types 1, 2 and 3 . 8
Table 3 – Electrical weak spots for types 1, 2 and 3 . 9
Table 4 – Maximum number of joins within a roll (types 1, 2 and 3) . 11

IEC 60674-3-1:2026 © IEC 2026
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
Plastic films for electrical purposes -
Part 3: Specifications for individual materials - Sheet 1: Biaxially oriented
polypropylene (PP) films for capacitors

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of a patent.
IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in respect
thereof. As of the date of publication of this document, IEC had not received notice of a patent, which may be
required to implement this document. However, implementers are cautioned that this may not represent the latest
information, which may be obtained from the patent database available at https://patents.iec.ch. IEC shall not be
held responsible for identifying any or all such patent rights.
IEC 60674-3-1 has been prepared by IEC technical committee 15: Solid electrical insulating
materials. It is an International Standard.
This third edition cancels and replaces the second edition published in 2021. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) this document has been completely revised editorially and technically;
b) the ranges of film thickness have been expanded;
c) the requirements of characteristics with the films of expanded thickness have been added.
The text of this International Standard is based on the following documents:
IEC 60674-3-1:2026 © IEC 2026
Draft Report on voting
15/1097/FDIS 15/1106/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
This document was dra
...