iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM C1519-10

(Practice)

Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures

Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures

SIGNIFICANCE AND USE
This test method describes the procedure to evaluate or compare, or both, the durability of sealants when subjected to accelerated weathering and cyclic movement in a joint.
Sealant installation procedures, design considerations and movement during cure affect the aging processes and are fundamental to the success of any sealant. These factors are not addressed with this test method.
The amount, type and frequency of movement a sealant experiences during its lifetime strongly depends on the materials used in construction and on the orientation of the joint toward sunlight and many other factors that are not uniform or consistent.
Climatic exposures will differ with the orientation of the building and shading as well as with local and regional climatic conditions. Climates in a given location can vary from year to year because of differences in solar radiation, temperature, rainfall, and atmospheric conditions. Further, the quality and intensity of solar radiation on the earth's surface varies with geographic location, season, time of day, and cloud cover.
Variations in results may be expected when operating conditions are varied within the accepted limits of this test method. Therefore, all test results using this test method must be accompanied by a report of the specific operating conditions as required in Section 12. Refer to Practice G151 for detailed information on the caveats applicable to use of results obtained according to this test method.
The results of laboratory exposure cannot be directly extrapolated to estimate an absolute rate of deterioration caused by natural weathering because the acceleration factor is material dependent and can be significantly different for each material and for different formulations of the same material. However, exposure of a similar material of known outdoor performance, a control, along with the test specimens allows comparison of the durability relative to that of the control under the test conditions. Evaluati...
SCOPE
1.1 This test method covers the method for the determination of the durability of a sealant based on its ability to function in cyclic movement maintaining adhesion and cohesion after repeated exposure to laboratory accelerated weathering procedures.
1.2 This test method describes two laboratory accelerated weathering procedures for evaluating the durability of a sealant.
1.3 RILEM TC139–DBS is related to this test method.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
14-Jul-2010
ICS
91.040.01 - Buildings in general
Technical Committee
C24 - Building Seals and Sealants
Drafting Committee
C24.40 - Weathering
Current Stage
Ref Project

Relations

Replaces
ASTM C1519-04 - Standard Practice for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures
Effective Date
15-Jul-2010
Referred By
ASTM C1193-16(2023) - Standard Guide for Use of Joint Sealants
Effective Date
15-Jul-2010
Referred By
ASTM C1021-08(2023) - Standard Practice for Laboratories Engaged in Testing of Building Sealants
Effective Date
15-Jul-2010

Buy Standard

ASTM C1519-10 - Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering ProceduresASTM C1519-10 - Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures
PreviousNext
Standard
ASTM C1519-10 - Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM C1519-10 - Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering ProceduresREDLINE ASTM C1519-10 - Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures
PreviousNext
Standard
REDLINE ASTM C1519-10 - Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C1519 − 10
Standard Test Method for
Evaluating Durability of Building Construction Sealants by
1
Laboratory Accelerated Weathering Procedures
This standard is issued under the fixed designation C1519; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope G154 Practice for Operating Fluorescent Ultraviolet (UV)
Lamp Apparatus for Exposure of Nonmetallic Materials
1.1 This test method covers the method for the determina-
G155 Practice for Operating XenonArc LightApparatus for
tionofthedurabilityofasealantbasedonitsabilitytofunction
Exposure of Non-Metallic Materials
in cyclic movement maintaining adhesion and cohesion after
3
2.2 RILEM Standard:
repeated exposure to laboratory accelerated weathering proce-
RILEMTC139–DBS Determination of changes in adhesion,
dures.
cohesion, and appearance of elastic weatherproofing seal-
1.2 This test method describes two laboratory accelerated
ants for high movement facade joints after exposure to
weathering procedures for evaluating the durability of a
artificial weathering
sealant.
3. Terminology
1.3 RILEM TC139–DBS is related to this test method.
3.1 The definitions given in Terminology C717 on terms
1.4 This standard does not purport to address all of the
relating to building seals and sealants and in Terminology
safety concerns, if any, associated with its use. It is the
G113 on terms relating to natural and artificial weathering tests
responsibility of the user of this standard to establish appro-
are applicable to this test method.
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use.
4. Significance and Use
2. Referenced Documents
4.1 This test method describes the procedure to evaluate or
2
compare, or both, the durability of sealants when subjected to
2.1 ASTM Standards:
accelerated weathering and cyclic movement in a joint.
C717 Terminology of Building Seals and Sealants
C719 Test Method for Adhesion and Cohesion of Elasto-
4.2 Sealant installation procedures, design considerations
meric Joint Sealants Under Cyclic Movement (Hockman
and movement during cure affect the aging processes and are
Cycle)
fundamentaltothesuccessofanysealant.Thesefactorsarenot
C1442 Practice for Conducting Tests on Sealants Using
addressed with this test method.
Artificial Weathering Apparatus
4.3 The amount, type and frequency of movement a sealant
E177 Practice for Use of the Terms Precision and Bias in
experiences during its lifetime strongly depends on the mate-
ASTM Test Methods
rials used in construction and on the orientation of the joint
G113 Terminology Relating to Natural andArtificial Weath-
toward sunlight and many other factors that are not uniform or
ering Tests of Nonmetallic Materials
consistent.
G141 Guide for Addressing Variability in Exposure Testing
4.4 Climatic exposures will differ with the orientation of the
of Nonmetallic Materials
buildingandshadingaswellaswithlocalandregionalclimatic
G151 Practice for Exposing Nonmetallic Materials inAccel-
conditions. Climates in a given location can vary from year to
erated Test Devices that Use Laboratory Light Sources
year because of differences in solar radiation, temperature,
rainfall, and atmospheric conditions. Further, the quality and
1
ThistestmethodisunderthejurisdictionofASTMCommitteeC24onBuilding
intensity of solar radiation on the earth’s surface varies with
Seals and Sealants and is the direct responsibility of Subcommittee C24.40 on
geographic location, season, time of day, and cloud cover.
Weathering.
Current edition approved July 15, 2010. Published September 2010. Originally
4.5 Variations in results may be expected when operating
approved in 2002. Last previous edition approved in 2004 as C1519 - 04. DOI:
conditions are varied within the accepted limits of this test
10.1520/C1519-10.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or method. Therefore, all test results using this test method must
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
3
the ASTM website. Published in Materials and Structures, 2001, pp. 34, 579–588.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C1519 − 10
beaccompaniedbyareportofthespecificoperatingconditions 6.2 Spacers, for the preparation of the specimens should be
as required in Section 11. Refer to Practice G151 for detailed of a non-adherent material and
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C1519–04
Standard Practice for Designation:C1519–10
Standard Test Method for
Evaluating Durability of Building Construction Sealants by
1
Laboratory Accelerated Weathering Procedures
This standard is issued under the fixed designation C1519; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This practice test method covers the method for the determination of the durability of a sealant based on its ability to
function in cyclic movement maintaining adhesion and cohesion after repeated exposure to laboratory accelerated weathering
procedures.
1.2 This practice test method describes two laboratory accelerated weathering procedures for evaluating the durability of a
sealant.
1.3The RILEM 1.3 RILEM TC139–DBS Durability Test Method is related to this practice. test method.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C717 Terminology of Building Seals and Sealants
C719 Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle)
C1442 Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus
E177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods
G113 Terminology Relating to Natural and Artificial Weathering Tests of Nonmetallic Materials
G141 Guide for Addressing Variability in Exposure Testing of Nonmetallic Materials
G151 Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources
G154 Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials
G155 Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials
3
2.2 RILEM Standard:
RILEM TC139–DBS Durability Test MethodDetermination Determination of changes in adhesion, cohesion, and appearance
of elastic weatherproofing sealants for high movement facade joints after exposure to artificial weathering
3. Terminology
3.1 The definitions given in Terminology C717 on terms relating to building seals and sealants and in Terminology G113 on
terms relating to natural and artificial weathering tests are applicable to this practice. test method.
4. Significance and Use
4.1 This practice test method describes the procedure to evaluate and/or compare or compare, or both, the durability of sealants
when subjected to accelerated weathering and cyclic movement in a joint.
1
This practice test method is under the jurisdiction ofASTM Committee C24 on Building Seals and Sealants and is the direct responsibility of Subcommittee C24.40 on
Weathering.
Current edition approved May 1, 2004. Published July 2004. Originally approved in 2002. Last previous edition approved in 2002 as C1519-02a. DOI: 10.1520/C1519-04.
Current edition approved July 15, 2010. Published September 2010. Originally approved in 2002. Last previous edition approved in 2004 as C1519 - 04. DOI:
10.1520/C1519-10.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Published in Materials and Structures (2001), pp. 34, 579–588. Materials and Structures, 2001, pp. 34, 579–588.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C1519–10
4.2 Sealant installation procedures, design considerations and movement during cure affect the aging processes and are
fundamental to the success of any sealant. These factors are not addressed with this test procedure. method.
4.3 The amount, type and frequency of movement a sealant experiences during its lifetime strongly depends on the materials
used in construction and on the orientation of the joint toward sunlight and many other factors that are not uniform or consistent.
4.4 Climatic exposures will differ with the orientation of the building and shading as well as with local and regional climatic
co
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM C1519-10(2022)(Test Method)
Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures

SIGNIFICANCE AND USE
4.1 This test method describes the procedure to evaluate or compare, or both, the durability of sealants when subjected to accelerated weathering and cyclic movement in a joint.  
4.2 Sealant installation procedures, design considerations and movement during cure affect the aging processes and are fundamental to the success of any sealant. These factors are not addressed with this test method.  
4.3 The amount, type and frequency of movement a sealant experiences during its lifetime strongly depends on the materials used in construction and on the orientation of the joint toward sunlight and many other factors that are not uniform or consistent.  
4.4 Climatic exposures will differ with the orientation of the building and shading as well as with local and regional climatic conditions. Climates in a given location can vary from year to year because of differences in solar radiation, temperature, rainfall, and atmospheric conditions. Further, the quality and intensity of solar radiation on the earth's surface varies with geographic location, season, time of day, and cloud cover.  
4.5 Variations in results may be expected when operating conditions are varied within the accepted limits of this test method. Therefore, all test results using this test method must be accompanied by a report of the specific operating conditions as required in Section 11. Refer to Practice G151 for detailed information on the caveats applicable to use of results obtained according to this test method.  
4.6 The results of laboratory exposure cannot be directly extrapolated to estimate an absolute rate of deterioration caused by natural weathering because the acceleration factor is material dependent and can be significantly different for each material and for different formulations of the same material. However, exposure of a similar material of known outdoor performance, a control, along with the test specimens allows comparison of the durability relative to that of the control under ...
SCOPE
1.1 This test method covers the method for the determination of the durability of a sealant based on its ability to function in cyclic movement maintaining adhesion and cohesion after repeated exposure to laboratory accelerated weathering procedures.  
1.2 This test method describes two laboratory accelerated weathering procedures for evaluating the durability of a sealant.  
1.3 RILEM TC139–DBS is related to this test method.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM E2844-23(Specification)
Standard Specification for Demonstrating That a Building’s Location Provides Access to Public Transit

ABSTRACT
This specification prescribes requirements for demonstrating that a building's location provides a minimal level of access to public transit that allows occupants to travel to places of employment and to run typical errands. It is intended to facilitate the decision-making process for selection of a building site that provides opportunities for occupants to use public transit. It specifies a single indicator regarding the environmental performance related to a building's location, and for evaluating whether a building is located in such a way as to minimize the impacts associated with occupants' travel.
SCOPE
1.1 This specification provides requirements for demonstrating that a building’s location provides a minimal level of access to public transit such that building occupants can rely on public transit to travel to places of employment and to run typical errands.  
1.2 This specification addresses a single indicator regarding the environmental performance related to a building’s location. It provides one option for evaluating whether a building is located in such a way as to minimize the impacts associated with occupants’ travel.
Note 1: The indicator in and of itself is insufficient to imply any level of “sustainability” for the building or the neighborhood. Similarly, a building’s failure to meet this specification does not necessarily signify a lack of sustainability. Other indicators may be more appropriate for that building or region; those indicators are outside the scope of this specification.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM E2432-23(Guide)
Standard Guide for General Principles of Sustainability Relative to the Built Environment

SIGNIFICANCE AND USE
4.1 The built environment has environmental, economic, and social impacts. These impacts occur at all life-cycle stages in multiple ways and on local, regional, and global scales. It is imperative to understand the nature of these impacts and their relationship to the general principles of sustainability in order to address the opportunities and challenges they present.  
4.1.1 It is necessary to identify the environmental impacts in order to promote the positive and mitigate the negative.  
4.1.2 It is necessary to quantify the economic impacts in order to improve life-cycle costs and benefits.  
4.1.3 It is necessary to identify the social impacts in order to contribute to a positive quality of life for current and future generations.  
4.2 The general principles of sustainability—environmental, economic, and social—are interrelated. Decisions founded on the opportunities and challenges of any of the principles will have impacts relative to all of the principles. However, to facilitate clarity in the presentation of the general principles, they are discussed individually in Section 5.  
4.3 The practical application of the general principles of sustainability relies upon balancing environmental, economic, and social impacts and committing to continual improvement. Section 6 discusses this balancing of environmental, economic, and social impacts in pursuit of sustainability.  
4.4 This guide provides an overview of sustainability, as it is applicable to the built environment. This guide provides general guidance but does not prescribe a specific course of action.  
4.5 This guide is intended to inform professionals associated with the building industry.  
4.5.1 The general principles identified in this guide are intended to assist users in making decisions that advance sustainability.  
4.5.2 The general principles identified in this guide are intended to inform the development and refinement of tools and standards to qualify and quantify impacts of the bu...
SCOPE
1.1 There are three general principles of sustainability: environmental, economic, and social. This guide covers application of the fundamental concepts and associated characteristics for each of the general principles of sustainability to the built environment.  
1.2 This guide identifies general methodologies associated with the decision-making process used in pursuing sustainability.  
1.3 The general principles identified in this guide are applicable to all life-cycle stages of design and construction within the built environment.  
1.4 A variety of tools and standards exist that qualify and quantify impacts of the built environment in terms of the general principles of sustainability. It is not within the scope of this standard to recreate or replace these tools.  
1.5 This guide does not provide direction as to the specific implementation of the general principles; nor does it provide direction as to the specific weighting of principles necessary for achieving balance between competing goals.  
1.6 Applying the principles in this guide will require professional judgment. Such judgment should be informed by experience with environmental, economic, and social issues as appropriate to the use, type, scale, and location.  
1.7 This guide offers an organized collection of information or a series of options but does not recommend a specific course of action. This document cannot replace education, experience, or community dialogue. Not all aspects of this guide may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects.  
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish a...

  • Guide
    5 pages
    English language
    sale 15% off
  • Guide
    5 pages
    English language
    sale 15% off
ASTM
ASTM E2114-23(Terminology)
Standard Terminology for Sustainability

SCOPE
1.1 This terminology2 consists of terms and definitions pertaining to sustainability.  
1.2 The purpose of this terminology is to provide meanings and explanations of terms applicable to sustainability. In the interest of common understanding and standardization, consistent word usage is encouraged to help eliminate the major barrier to effective technical communication.  
1.3 It is recommended that terms used only within an individual standard, and having a meaning unique to that standard, be defined or explained in the terminology section of that individual standard.  
1.4 Certain standard definitions herein are adopted from other sources. Each is an exact copy. The source is identified at the right margin following the definition and is listed in Section 2.  
1.5 Terms are listed in alphabetical sequence. Compound terms appear in the natural spoken order.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM E3026-23e1(Guide)
Standard Guide for Readily Observable Moisture Affected Materials and Conditions Conducive to Elevated Moisture in Commercial Buildings: Limited Moisture Assessment Process

SIGNIFICANCE AND USE
4.1 Use—This guide is intended for use on a voluntary basis by parties who wish to obtain a limited survey of commercial real estate to assess for readily observable moisture affected materials and physical deficiencies conducive to elevated moisture as part of a commercial real estate transaction or commercial property management. This guide is intended to constitute a limited inquiry using representative observations for the purposes of conducting due diligence regarding the actual and potential presence of readily observable moisture affected materials and physical deficiencies conducive to elevated moisture in connection with the subject property. Inquiries that are more and less comprehensive than this guide (including, in some instances, no inquiry) may be appropriate in some circumstances in the opinion of the user (for example, when the presence of moisture affected materials is known to the user). Furthermore, no implication is intended that a person must use this guide in order to be deemed to have conducted appropriate inquiry in a commercially prudent or reasonable manner in a particular transaction. Nevertheless, this guide is intended to reflect a commercially prudent and reasonable inquiry. However, a LMA is not intended to serve as a comprehensive survey for the presence of readily observable moisture affected materials and physical deficiencies conducive to elevated moisture in all or most of the building systems throughout a commercial building.  
4.2 Clarification of Use:  
4.2.1 Specific Point in Time—Because conditions conducive to elevated moisture in a building can vary greatly over time due to changes in weather, interior air handling and conditioning, occupancy, and so forth, a user should only rely on the results presented in the report for the point in time at which the LMA was conducted.  
4.2.2 Site-Specific—This guide is site-specific in that it relates to assessment of readily observable moisture affected materials and physical def...
SCOPE
1.1 Purpose—The purpose of this guide2 is to define good commercial practice for conducting a limited survey for readily observable moisture affected materials and conditions conducive to elevated moisture in a commercial building related to commercial real estate transaction or commercial real estate management by conducting: a walk-through survey, document reviews, and interviews as outlined within this guide. This guide is intended to provide a practical means for the limited identification of moisture affected materials and physical deficiencies conducive to elevated moisture caused by water infiltration through the building envelope or substructure or generated within the subject building as a result of processes or mechanical systems, excluding de minimis conditions. This guide is to allow a user to assess general moisture concerns, as well as the potential need for further assessment or other actions that may be appropriate that are beyond the scope of this guide. For purposes of this guide, the initialism “LMA” or “Limited Moisture Assessment” is used interchangeably with this guide’s full title.  
1.2 Purpose Limitations—While a LMA may be used to survey for readily identifiable moisture affected materials and physical deficiencies conducive to elevated moisture, the LMA is not designed to serve as comprehensive survey for the presence of moisture affected materials and physical deficiencies conducive to elevated moisture in all or most areas in a commercial building. It is not intended to reduce or eliminate the risks that elevated moisture may pose to the subject building or its occupants.  
1.3 Considerations Beyond This Scope—The use of this guide is limited to the scope set forth in this section. Section 12 of this guide identifies, for informational purposes, certain physical conditions (not an all-inclusive list) that may exist at a subject property and certain activities or procedures (not an all-inclu...

  • Guide
    24 pages
    English language
    sale 15% off
ASTM
ASTM D7338-14(2023)(Guide)
Standard Guide for Assessment Of Fungal Growth in Buildings

SIGNIFICANCE AND USE
5.1 This guide presents options for a systematic assessment of fungal growth in buildings.  
5.2 This guide allows for site-specific flexibility and professional judgment in the choice of assessment procedures. It may not be necessary to perform in its entirety the basic assessment presented below to resolve a particular problem, for example, where fungal growth is localized and the source and extent of moisture is readily observable.  
5.3 Conversely, no matter how comprehensive the survey, all fungal growth may not be identified or located in a fungal assessment.  
5.4 Material removal or destructive investigation may be needed to access suspect surfaces.  
5.5 Using the procedures described in this guide, the investigator may have obtained the data necessary to suggest specific recommendations, for example, how to remediate the observed fungal growth, or how to prevent further fungal growth, but those recommendations are beyond the scope of this guide.  
5.6 Precautions may be needed to protect the assessor and building occupants where access may disturb fungal growth.  
5.7 It is the user’s responsibility to protect information that may be considered confidential, or private, or both, in accordance with project contract, corporate protocol, or local, state, and federal regulations, or a combination thereof.  
5.8 It may be necessary to enlist other disciplines or trade expertise to assist in some steps of the assessment, but recommendations of when to enlist and whom to enlist are beyond the scope of this guide.
SCOPE
1.1 This guide provides a compendium of information and a menu of options for assessment of fungal growth in buildings, but does not recommend a specific course of action. Due to the wide variety of fungal problems affecting buildings and their occupants, and the wide variety of buildings, it is not possible to describe a set of uniform steps that will always be performed during an assessment (that is, a standard practice); therefore the user of this guide must decide which steps are appropriate for a given situation or building.  
1.2 This guide is specific to fungal growth, which is only one potential problem in a building environment. It may be part of, but is not intended to take the place of, a comprehensive indoor air quality investigation.  
1.3 This guide describes minimum steps and procedures for collecting background information on a building in question, procedures for evaluating the potential for moisture infiltration or collection, procedures for inspection for suspect fungal growth, and procedures beyond the scope of a basic survey that may be useful for specific problems.  
1.4 Assessments for fungal growth may be useful wherever fungal growth is suspected, excess moisture has been present or when there are concerns regarding potential fungal growth.  
1.5 Periodic fungal assessment in buildings may be a component of preventative maintenance programs.  
1.6 This guide is applicable to buildings including residential (for example, single or multi-family), institutional (for example, schools, hospitals), government, public assembly, commercial (for example, office, retail), and industrial facilities.  
1.7 Recommendations for developing a sampling strategy or methods for the collection and analysis of fungal samples are beyond the scope of this guide. For recommendations for developing a sampling strategy, see Ref (1)2, Chapter 10.  
1.8 Recommendations for remediation of fungal growth are beyond the scope of this guide.  
1.9 This guide is not intended to supersede any government regulations governing the assessment of fungal growth in buildings.  
1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use...

  • Guide
    9 pages
    English language
    sale 15% off
ASTM
ASTM E2921-22(Practice)
Standard Practice for Minimum Criteria for Comparing Whole Building Life Cycle Assessments for Use with Building Codes, Standards, and Rating Systems

SIGNIFICANCE AND USE
5.1 This practice provides criteria that building design teams shall use to compare the environmental impacts associated with a reference building design and a final building design, including additions to existing buildings where applicable.  
5.2 This practice deals specifically with material selection for initial construction, including associated maintenance and replacement cycles over an assumed service life, taking operating energy use into account if required or explicitly allowed under the applicable code, standard, or rating system.
SCOPE
1.1 This practice provides criteria to be applied irrespective of the assessment (LCA) tool that is used when LCA is undertaken at the whole building level to compare a final whole building design to a reference building design.  
1.2 The purpose of this practice is to support the use of whole building Life Cycle Assessment (LCA) in building codes, standards, and building rating systems by ensuring that comparative assessments of final whole building designs relative to reference building designs take account of the relevant building features, life cycle stages, and related activities in similar fashion for both the reference and final building designs of the same building.  
1.3 The criteria do not deal with building occupant behavior, possible future changes in building function, building rehabilitation or retrofit, or other matters that cannot be foreseen or reasonably estimated at the design or permitting stage, or both where this practice applies.  
1.4 Only environmental impacts and aspects of sustainability are addressed in this practice. The social and economic impacts and aspects of sustainability are not addressed in this practice.  
1.5 This practice does not deal with basic LCA methodology, calculation methods or related matters that are covered in cited international standards.  
1.6 This practice does not supersede or modify existing ISO standards for the application of LCA at the product level, nor does it address any of the following related applications:  
1.6.1 Aggregation of building products Environmental Product Declarations (EPD) at the whole building level;  
1.6.2 Rules for applying EPDs in a building code, standard, or rating system; and  
1.6.3 Comparability of building product EPDs.
Note 1: ISO 14025 and ISO 21930 provide guidance on use and comparability of building products EPDs.  
1.7 This practice does not specify the impact categories or sustainability aspects to be addressed in building codes, standards, or building rating systems and users of this practice conform to the impact category requirements specified in the applicable code, standard, or rating system.  
1.8 The text of this standard contains notes that provide explanatory material. These notes shall not be considered as requirements of the standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM C1519-10(2022)(Test Method)
Standard Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures

SIGNIFICANCE AND USE
4.1 This test method describes the procedure to evaluate or compare, or both, the durability of sealants when subjected to accelerated weathering and cyclic movement in a joint.  
4.2 Sealant installation procedures, design considerations and movement during cure affect the aging processes and are fundamental to the success of any sealant. These factors are not addressed with this test method.  
4.3 The amount, type and frequency of movement a sealant experiences during its lifetime strongly depends on the materials used in construction and on the orientation of the joint toward sunlight and many other factors that are not uniform or consistent.  
4.4 Climatic exposures will differ with the orientation of the building and shading as well as with local and regional climatic conditions. Climates in a given location can vary from year to year because of differences in solar radiation, temperature, rainfall, and atmospheric conditions. Further, the quality and intensity of solar radiation on the earth's surface varies with geographic location, season, time of day, and cloud cover.  
4.5 Variations in results may be expected when operating conditions are varied within the accepted limits of this test method. Therefore, all test results using this test method must be accompanied by a report of the specific operating conditions as required in Section 11. Refer to Practice G151 for detailed information on the caveats applicable to use of results obtained according to this test method.  
4.6 The results of laboratory exposure cannot be directly extrapolated to estimate an absolute rate of deterioration caused by natural weathering because the acceleration factor is material dependent and can be significantly different for each material and for different formulations of the same material. However, exposure of a similar material of known outdoor performance, a control, along with the test specimens allows comparison of the durability relative to that of the control under ...
SCOPE
1.1 This test method covers the method for the determination of the durability of a sealant based on its ability to function in cyclic movement maintaining adhesion and cohesion after repeated exposure to laboratory accelerated weathering procedures.  
1.2 This test method describes two laboratory accelerated weathering procedures for evaluating the durability of a sealant.  
1.3 RILEM TC139–DBS is related to this test method.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM E541-22(Specification)
Standard Specification for Agencies Engaged in System Analysis and Compliance Assurance for Manufactured Building

ABSTRACT
This specification covers agencies engaged in system analysis and compliance assurance for manufactured building. The administrative agency may utilize the services and facilities of building-evaluation agencies in carrying out its responsibilities for evaluating manufactured building systems. By providing criteria for evaluating these agencies, this standard's objective is to (1) utilize the voluntary standards system to provide a common base for the various regulatory approaches employed by the authorities having jurisdiction, and (2) make provision for varying degrees of optional technical support for the certification of manufactured building. The system analysis agency is responsible for determining whether a building system, including the design, materials, and fabrication process, is in conformance with applicable requirements. The documents of the system analysis function are: product description document, compliance assurance manual, and installation documents. The general procedures for system analysis are presented in details. The tasks of system analysis project manager, technical staff evaluating building systems, technical staff evaluating compliance assurance manuals, and project manager evaluating building systems are presented in details. The requirements and criteria for compliance assurance agencies are presented. The task of compliance assurance agency project manager, technical staff preparing compliance assurance manuals, compliance assurance supervisor of inspection, and compliance assurance inspector are presented in details.
SCOPE
1.1 This specification provides the criteria for the administrative agency that has regulatory authority as granted by the authority having jurisdiction AHJ to evaluate the capabilities and qualifications of building evaluation agencies, that performs system analysis or compliance assurance or both for certification of manufactured building on behalf of an authority having jurisdiction (AHJ) that meet the needs of regulatory programs. Administrative agencies and building evaluation agencies (third-party agencies) are the primary users of the standard.  
1.2 To establish an appropriate degree of intra- and inter-state credibility regarding building system evaluations made through governmental or private agencies, the authorities having jurisdiction should utilize an oversight and approval process for the building-evaluation agencies that provide the services of system analysis or compliance assurance on behalf of the AHJ that may include: approval by the AHJ for both oversight and or auditing of the regulatory body, or approval by the AHJ and oversight, and or auditing by an independent auditor for the regulatory body, or approval with the AHJ and oversight, and auditing by an independent accreditation agency.  
1.3 Building-evaluation agencies examined under this specification may include governmental or private agencies or both.  
1.4 Practice E651 may be used to support the evaluation of building-evaluation agencies. Other criteria such as independence, financial stability, and objectivity may need to be considered.  
Note 1: Practice E651 is intended as a companion standard to Specification E541 and includes questions that should be asked of system analysis and compliance assurance agencies in order for the administrative agency to evaluate their competency.  
1.5 These criteria set forth the minimum personnel requirements and the technical and organizational procedures required for building-evaluation agencies engaged in evaluating manufactured building.  
1.6 Criteria are included for building-evaluation agencies evaluating innovative as well as conventional building systems, against applicable requirements.  
1.7 Building-evaluation agencies involved in testing, quality assurance, and evaluating building components can be evaluated by using Specification E699.  
1.7.1 Specification E699 is used in conjunction with Specification E541 and P...

  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM E1678-21a(Test Method)
Standard Test Method for Measuring Smoke Toxicity for Use in Fire Hazard Analysis

SIGNIFICANCE AND USE
5.1 This test method has been designed to provide data for the mathematical modeling of fire hazard as a means for the evaluation of materials and products and to assist in their research and development.  
5.1.1 Test Method E1678 is functionally equivalent to NFPA 269-2017.  
5.2 This test method is used to predict, and subsequently confirm, the lethal toxic potency of smoke produced upon the exposure of a material or product to specific fire test conditions. Confirmation determines whether certain major gaseous toxicants account for the observed toxic effects and lethal toxic potency. If a predicted lethal toxic potency value is not confirmed adequately, indicating a potential for unusual or unexplained toxicity, the lethal toxic potency will need to be investigated using other methodology, such as conducting an experimental determination of the LC50 using the apparatus described. (See X1.3.1 and X1.3.2.)  
5.3 This test method produces lethal toxic potency values that are appropriate for use in the modeling of both pre-flashover and post-flashover fires. Most fire deaths due to smoke inhalation in the U.S. occur in areas other than the room of fire origin and are caused by fires that have proceeded beyond the room of fire origin. It is assumed that these are flashover fires. Therefore, the principal emphasis is placed on evaluating toxic hazard under these conditions. In post-flashover fires, large concentrations of carbon monoxide results from reduced air supply to the fire plume and other room-scale factors. Bench-scale tests do not have the capacity to simulate these phenomena. The lethal toxic potency values determined in this test method are obtained from fuel/air ratios more representative of pre-flashover, rather than post-flashover conditions. In cases where a pre-flashover fire representation is desired in fire hazard modeling, these LC50 values are appropriate. Lethal toxic potency and carbon monoxide yield values determined in this test method requi...
SCOPE
1.1 This fire-test-response standard covers a means for determining the lethal toxic potency of smoke produced from a material or product ignited while exposed to a radiant heat flux of 50 kW/m2 for 15 min.  
1.2 This test method is limited to test specimens no larger than 76 mm by 127 mm (3 in. by 5 in.), with a thickness no greater than 51 mm (2 in.). Specimens are intended to be representative of finished materials or products, including composite and combination systems.  
1.3 Lethal toxic potency values associated with 30-min exposures are predicted using calculations that use combustion atmosphere analytical data for carbon monoxide, carbon dioxide, oxygen (vitiation) and, if present, hydrogen cyanide, hydrogen chloride, and hydrogen bromide. The predictive equations are therefore limited to those materials and products whose smoke toxicity can be attributed to these toxicants. An animal check determines the extent to which additional toxicants contribute to the lethal toxic potency of the smoke.  
1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.5 This standard measures and describes the response of materials, products, or assemblies in response to heat under controlled conditions, but does not by itself incorporate all factors required for fire hazard of fire risk assessment of the materials, products, or assemblies under actual fire conditions.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations (particularly with regard to the care and use of experimental animals) prior to use. For specific hazards statements, see Section 7 and Note X1.1.  ...

  • Standard
    15 pages
    English language
    sale 15% off
  • Standard
    15 pages
    English language
    sale 15% off