ASTM D5319-17
(Specification)Standard Specification for Glass-Fiber Reinforced Polyester Wall and Ceiling Panels
Standard Specification for Glass-Fiber Reinforced Polyester Wall and Ceiling Panels
ABSTRACT
This specification covers the classification, materials of construction, workmanship, physical requirements, and methods of testing glass-fiber-reinforced polyester composite wall and ceiling panels intended for use in light construction and semi-structural applications. The panels shall be divided into four classifications based on relative response to the laboratory flammability: Class A; Class B; Class C; and Class D. These classifications may be further subdivided into grades based on nominal thickness when tested: Grade 1; Grade 2; Grade 3; Grade 4; Grade 5; Grade 6; and Grade 7. The polyester resin used in the composite shall be a thermosetting polyester resin with cross-linking monomers composed of polymeric esters in which the recurring ester groups are an integral part of the main polymer chain. The resin shall be reinforced with glass fibers. Conditioning; length and width; squareness; thickness; camber; color; impact resistance; and burning characteristics tests shall be performed to conform to the requirements specified.
SCOPE
1.1 This specification covers the classification, materials of construction, workmanship, physical requirements, and methods of testing glass-fiber-reinforced polyester composite wall and ceiling panels intended for use in light construction and semi-structural applications.
1.2 Supplementary information on chemical resistance, impact resistance, and installation practice are provided in Appendix X1.
1.3 The classification of these composite panels into classes based on relative response to a laboratory test shall not be considered a fire-hazard classification.
1.4 Laboratory flammability tests (Test Methods E84 and D1929) applicable to this specification should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or conditions. However, results may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use.
1.5 The intent of this specification is to define the class, grade, and general laminate properties of the composite wall and ceiling liner panels in order to ensure a quality product which will perform in the intended application. This specification is not intended to restrict or limit technological changes affecting performance when changes are agreed upon between the purchaser and manufacturer.
1.6 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only.
1.7 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in Tables and Figures) shall not be considered as requirements of this specification.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: There is no known ISO equivalent to this standard.
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D5319 −17 An American National Standard
Standard Specification for
1
Glass-Fiber Reinforced Polyester Wall and Ceiling Panels
This standard is issued under the fixed designation D5319; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 1.8 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
1.1 This specification covers the classification, materials of
responsibility of the user of this standard to establish appro-
construction, workmanship, physical requirements, and meth-
priate safety, health and environmental practices and deter-
ods of testing glass-fiber-reinforced polyester composite wall
mine the applicability of regulatory limitations prior to use.
and ceiling panels intended for use in light construction and
semi-structural applications.
NOTE 1—There is no known ISO equivalent to this standard.
1.9 This international standard was developed in accor-
1.2 Supplementary information on chemical resistance, im-
dance with internationally recognized principles on standard-
pact resistance, and installation practice are provided in Ap-
ization established in the Decision on Principles for the
pendix X1.
Development of International Standards, Guides and Recom-
1.3 The classification of these composite panels into classes
mendations issued by the World Trade Organization Technical
based on relative response to a laboratory test shall not be
Barriers to Trade (TBT) Committee.
considered a fire-hazard classification.
1.4 Laboratory flammability tests (Test Methods E84 and 2. Referenced Documents
D1929) applicable to this specification should be used to 2
2.1 ASTM Standards:
measure and describe the properties of materials, products, or
D374/D374M Test Methods for Thickness of Solid Electri-
assemblies in response to heat and flame under controlled
cal Insulation
laboratory conditions and should not be used to describe or
D618 Practice for Conditioning Plastics for Testing
appraise the fire hazard or conditions. However, results may be
D883 Terminology Relating to Plastics
used as elements of a fire risk assessment which takes into
D1600 Terminology forAbbreviatedTerms Relating to Plas-
account all of the factors which are pertinent to an assessment
tics
of the fire hazard of a particular end use.
D1929 Test Method for Determining Ignition Temperature
1.5 The intent of this specification is to define the class, of Plastics
grade, and general laminate properties of the composite wall D2244 Practice for Calculation of Color Tolerances and
and ceiling liner panels in order to ensure a quality product Color Differences from Instrumentally Measured Color
which will perform in the intended application. This specifi- Coordinates
cation is not intended to restrict or limit technological changes E84 Test Method for Surface Burning Characteristics of
affecting performance when changes are agreed upon between Building Materials
the purchaser and manufacturer. E631 Terminology of Building Constructions
1.6 The values stated in inch-pound units are to be regarded
3. Terminology
as the standard. The values given in parentheses are provided
3.1 General—DefinitionsareinaccordancewithTerminolo-
for information only.
gies D883 and E631 and abbreviations with Terminology
1.7 The text of this specification references notes and
D1600, unless otherwise indicated.
footnotes that provide explanatory material. These notes and
3.2 Definitions of Terms Specific to This Standard:
footnotes (excluding those in Tables and Figures) shall not be
3.2.1 camber, n—non-linearity of the long axis of a panel.
considered as requirements of this specification.
NOTE 2—In the process of water jet, knife, saw, or rotary shear
trimmingofacontinuouspanel,sidewardsmotionofthepanelthroughthe
1
This specification is under the jurisdiction of ASTM Committee D20 on
Plastics and is the direct responsibility of Subcommittee D20.24 on Plastic Building
2
Products. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Sept. 1, 2017. Published September 2017. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1992. Last previous edition approved in 2012 as D5319 – 12. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/D5319-17. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ---------
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D5319 − 12 D5319 − 17 An American National Standard
Standard Specification for
1
Glass-Fiber Reinforced Polyester Wall and Ceiling Panels
This standard is issued under the fixed designation D5319; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers the classification, materials of construction, workmanship, physical requirements, and methods of
testing glass-fiber-reinforced polyester composite wall and ceiling panels intended for use in light construction and semi-structural
applications.
1.2 Supplementary information on chemical resistance, impact resistance, and installation practice are provided in Appendix
X1.
1.3 The classification of these composite panels into classes based on relative response to a laboratory test shall not be
considered a fire-hazard classification.
1.4 Laboratory flammability tests (Test Methods E84 and D1929) applicable to this specification should be used to measure and
describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions
and should not be used to describe or appraise the fire hazard or conditions. However, results may be used as elements of a fire
risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular
end use.
1.5 The intent of this specification is to define the class, grade, and general laminate properties of the composite wall and ceiling
liner panels in order to ensure a quality product which will perform in the intended application. This specification is not intended
to restrict or limit technological changes affecting performance when changes are agreed upon between the purchaser and
manufacturer.
1.6 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for
information only.
1.7 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes
(excluding those in Tables and Figures) shall not be considered as requirements of this specification.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use.
NOTE 1—There is no known ISO equivalent to this standard.
NOTE 1—There is no known ISO equivalent to this standard.
1.9 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D374D374/D374M Test Methods for Thickness of Solid Electrical Insulation (Metric) D0374_D0374M
D618 Practice for Conditioning Plastics for Testing
D883 Terminology Relating to Plastics
D1600 Terminology for Abbreviated Terms Relating to Plastics
1
This specification is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.24 on Plastic Building Products.
Current edition approved Oct. 1, 2012Sept. 1, 2017. Published November 2012September 2017. Originally approved in 1992. Last previous edition approved in 20082012
as D5319 – 97(2008).12. DOI: 10.1520/D5319-12.10.1520/D5319-17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D5319 − 17
D1929 Test Method for Determining Ignition Temperature of Plastics
D2244 Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
D3029 Test Methods for Impact Resistance of Flat, Rigid Pla
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.