F08.15 - Ice Hockey

SCOPE
1.1 This specification covers performance requirements and test methods for face protectors marketed, sold, and intended for ice hockey.  
1.2 The intent of this specification is to reduce the risk of injury to the face without compromising the form or appeal of the game. To do so, the face protector shall be used:  
1.2.1 As intended within the rules of the game and  
1.2.2 In accordance with the manufacturer’s instructions.  
1.3 Ice hockey is a sport with intrinsic hazards associated with the normal conduct of the game. Participation in ice hockey implies the acceptance of some risk of injury. Use of a face protector certified to this specification will not prevent all injuries.  
1.4 This specification has been prepared after careful consideration of the frequency and mechanisms associated with facial and eye injuries that can potentially occur within the rules of the game of ice hockey.  
1.5 Requirements and the corresponding test methods, where appropriate, are given for the following:  
1.5.1 Construction,  
1.5.2 Puck impact resistance,  
1.5.3 Penetration,  
1.5.4 Field of vision, and  
1.5.5 Marking and information.  
1.6 Face protection is intended for use by players, goalkeepers, and certain functionaries (for example, referees and coaches). Types of protectors considered under this specification are:  
1.6.1 Type B1—A full-face protector intended for use by persons older than ten years of age, other than goaltenders;  
1.6.2 Type B2—A full-face protector intended for use by persons ten years of age or younger, other than goaltenders; and  
1.6.3 Type C (Visor)—A visor intended for use by person in the junior age category and older, other than goaltenders.  
1.7 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.  
1.8 Use of the singular does not exclude the plural (and vice versa) when the sense allows.  
1.9 Although the intended primary application of this specification is stated in this scope, note that it remains the responsibility of the users of this specification to judge its suitability for their particular purpose.  
1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.11 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This performance specification2 covers performance requirements for ice hockey helmets.  
1.2 The intent of this performance specification is to reduce the risk of injury to the head without compromising the form and appeal of the game.  
1.3 This performance specification covers: (1) performance tests for shock absorption properties of the complete helmet and strength and elongation of the chin strap and its attachment; and (2) requirements for area of coverage and penetration.  
1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.5 The following precautionary caveat pertains only to the test methods portion, Section 12, of this performance specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This document covers specifications and conformity assessment methods for new head and face protectors for ice hockey goaltenders, as offered for initial sale. This specification is intended to reduce the risk of injury associated with playing the position of goaltender in ice hockey. The protectors are classified according to types: Type I and Type II. Optical tests, shock attenuation tests, puck impact tests, penetration resistance tests, and neck strap retention test shall be performed to meet the requirements specified.
SCOPE
1.1 This performance specification2 covers performance requirements for ice hockey goaltender head and face protectors.  
1.2 The intent of this performance specification is to reduce the risk of injury to the head and face of ice hockey goaltenders without compromising the form and appeal of the game.  
1.3 This specification has requirements for: (1)  materials, assembly, and design; (2) protected areas (coverage) and penetration resistance; (3) shock absorption; (4) puck impact resistance; (5) extensibility and strength of the chin strap and its attachment; and (6) optical quality.  
1.4 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers performance requirements and corresponding test methods for throat protectors marketed, sold, and intended for use by ice hockey goalkeepers. It aims to reduce the risk of injury to the throat without compromising the form or appeal of the game. To this end, the protector shall be used as intended within the rules of the game and in accordance with the manufacturer's instructions.
This specification includes a protocol for testing throat protectors, which covers: construction, coverage, marking, and information relevant to users as well as sampling, low-temperature conditioning, determination of Head-Positioning Index (HPI) and puck impact resistance, and information that must be contained in the test report.
SCOPE
1.1 This specification covers performance requirements and test methods for throat protectors marketed, sold, and intended for ice hockey goalkeepers.  
1.2 The intent of this specification is to reduce the risk of injury to the throat without compromising the form or appeal of the game. To do so, the protector shall be used:  
1.2.1 As intended within the rules of the game and  
1.2.2 In accordance with the manufacturer’s instructions.  
1.3 Ice hockey is a sport with intrinsic hazards associated with the normal conduct of the game. Participation in ice hockey implies the acceptance of some risk of injury. Use of a throat protector certified to this specification will not prevent all injuries.  
1.4 This specification has been prepared after careful consideration of the frequency and mechanisms associated with throat injuries that can potentially occur within the rules of the game of ice hockey.  
1.5 Requirements and the corresponding test methods, where appropriate, are given for the following:  
1.5.1 Construction,  
1.5.2 Puck impact resistance,  
1.5.3 Coverage,  
1.5.4 Marking and information.  
1.6 Throat protection is intended for use by goalkeepers.  
1.7 Use of the singular does not exclude the plural (and vice versa) when the sense allows.  
1.8 Although the intended primary application of this specification is stated in this scope, note that it remains the responsibility of the users of this specification to judge its suitability for their particular purpose.  
1.9 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.11 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers performance requirements and test methods for face protectors marketed, sold, and intended for ice hockey.  
1.2 The intent of this specification is to reduce the risk of injury to the face without compromising the form or appeal of the game. To do so, the face protector shall be used:  
1.2.1 As intended within the rules of the game and  
1.2.2 In accordance with the manufacturer’s instructions.  
1.3 Ice hockey is a sport with intrinsic hazards associated with the normal conduct of the game. Participation in ice hockey implies the acceptance of some risk of injury. Use of a face protector certified to this specification will not prevent all injuries.  
1.4 This specification has been prepared after careful consideration of the frequency and mechanisms associated with facial and eye injuries that can potentially occur within the rules of the game of ice hockey.  
1.5 Requirements and the corresponding test methods, where appropriate, are given for the following:  
1.5.1 Construction,  
1.5.2 Puck impact resistance,  
1.5.3 Penetration,  
1.5.4 Field of vision, and  
1.5.5 Marking and information.  
1.6 Face protection is intended for use by players, goalkeepers, and certain functionaries (for example, referees and coaches). Types of protectors considered under this specification are:  
1.6.1 Type B1—A full-face protector intended for use by persons older than ten years of age, other than goaltenders;  
1.6.2 Type B2—A full-face protector intended for use by persons ten years of age or younger, other than goaltenders; and  
1.6.3 Type C (Visor)—A visor intended for use by person in the junior age category and older, other than goaltenders.  
1.7 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.  
1.8 Use of the singular does not exclude the plural (and vice versa) when the sense allows.  
1.9 Although the intended primary application of this specification is stated in this scope, note that it remains the responsibility of the users of this specification to judge its suitability for their particular purpose.  
1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.11 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This document covers specifications and conformity assessment methods for new head and face protectors for ice hockey goaltenders, as offered for initial sale. This specification is intended to reduce the risk of injury associated with playing the position of goaltender in ice hockey. The protectors are classified according to types: Type I and Type II. Optical tests, shock attenuation tests, puck impact tests, penetration resistance tests, and neck strap retention test shall be performed to meet the requirements specified.
SCOPE
1.1 This performance specification2 covers performance requirements for ice hockey goaltender head and face protectors.  
1.2 The intent of this performance specification is to reduce the risk of injury to the head and face of ice hockey goaltenders without compromising the form and appeal of the game.  
1.3 This specification has requirements for: (1)  materials, assembly, and design; (2) protected areas (coverage) and penetration resistance; (3) shock absorption; (4) puck impact resistance; (5) extensibility and strength of the chin strap and its attachment; and (6) optical quality.  
1.4 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This performance specification2 covers performance requirements for ice hockey helmets.  
1.2 The intent of this performance specification is to reduce the risk of injury to the head without compromising the form and appeal of the game.  
1.3 This performance specification covers: (1) performance tests for shock absorption properties of the complete helmet and strength and elongation of the chin strap and its attachment; and (2) requirements for area of coverage and penetration.  
1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.5 The following precautionary caveat pertains only to the test methods portion, Section 12, of this performance specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This performance specification2 covers performance requirements for ice hockey helmets.  
1.2 The intent of this performance specification is to reduce the risk of injury to the head without compromising the form and appeal of the game.  
1.3 This performance specification covers: (1) performance tests for shock absorption properties of the complete helmet and strength and elongation of the chin strap and its attachment; and (2) requirements for area of coverage and penetration.  
1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.5 The following precautionary caveat pertains only to the test methods portion, Section 12, of this performance specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers performance requirements and corresponding test methods for throat protectors marketed, sold, and intended for use by ice hockey goalkeepers. It aims to reduce the risk of injury to the throat without compromising the form or appeal of the game. To this end, the protector shall be used as intended within the rules of the game and in accordance with the manufacturer's instructions.
This specification includes a protocol for testing throat protectors, which covers: construction, coverage, marking, and information relevant to users as well as sampling, low-temperature conditioning, determination of Head-Positioning Index (HPI) and puck impact resistance, and information that must be contained in the test report.
SCOPE
1.1 This specification covers performance requirements and test methods for throat protectors marketed, sold, and intended for ice hockey goalkeepers.  
1.2 The intent of this specification is to reduce the risk of injury to the throat without compromising the form or appeal of the game. To do so, the protector shall be used:  
1.2.1 As intended within the rules of the game and  
1.2.2 In accordance with the manufacturer’s instructions.  
1.3 Ice hockey is a sport with intrinsic hazards associated with the normal conduct of the game. Participation in ice hockey implies the acceptance of some risk of injury. Use of a throat protector certified to this specification will not prevent all injuries.  
1.4 This specification has been prepared after careful consideration of the frequency and mechanisms associated with throat injuries that can potentially occur within the rules of the game of ice hockey.  
1.5 Requirements and the corresponding test methods, where appropriate, are given for the following:  
1.5.1 Construction,  
1.5.2 Puck impact resistance,  
1.5.3 Coverage,  
1.5.4 Marking and information.  
1.6 Throat protection is intended for use by goalkeepers.  
1.7 Use of the singular does not exclude the plural (and vice versa) when the sense allows.  
1.8 Although the intended primary application of this specification is stated in this scope, note that it remains the responsibility of the users of this specification to judge its suitability for their particular purpose.  
1.9 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This performance specification2 covers performance requirements for ice hockey helmets.  
1.2 The intent of this performance specification is to reduce the risk of injury to the head without compromising the form and appeal of the game.  
1.3 This performance specification covers: (1) performance tests for shock absorption properties of the complete helmet and strength and elongation of the chin strap and its attachment; and (2) requirements for area of coverage and penetration.  
1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.5 The following precautionary caveat pertains only to the test methods portion, Section 12, of this performance specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This performance specification2 covers performance requirements for ice hockey helmets.  
1.2 The intent of this performance specification is to reduce the risk of injury to the head without compromising the form and appeal of the game.  
1.3 This performance specification covers: (1) performance tests for shock absorption properties of the complete helmet and strength and elongation of the chin strap and its attachment; and (2) requirements for area of coverage and penetration.  
1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.5 The following precautionary caveat pertains only to the test methods portion, Section 12, of this performance specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This document covers specifications and conformity assessment methods for new head and face protectors for ice hockey goaltenders, as offered for initial sale. This specification is intended to reduce the risk of injury associated with playing the position of goaltender in ice hockey. The protectors are classified according to types: Type I and Type II. Optical tests, shock attenuation tests, puck impact tests, penetration resistance tests, and neck strap retention test shall be performed to meet the requirements specified.
SCOPE
1.1 This performance specification2 covers performance requirements for ice hockey goaltender head and face protectors.  
1.2 The intent of this performance specification is to reduce the risk of injury to the head and face of ice hockey goaltenders without compromising the form and appeal of the game.  
1.3 This specification has requirements for: (1)  materials, assembly, and design; (2) protected areas (coverage) and penetration resistance; (3) shock absorption; (4) puck impact resistance; (5) extensibility and strength of the chin strap and its attachment; and (6) optical quality.  
1.4 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This document covers specifications and conformity assessment methods for new head and face protectors for ice hockey goaltenders, as offered for initial sale. This specification is intended to reduce the risk of injury associated with playing the position of goaltender in ice hockey. The protectors are classified according to types: Type I and Type II. Optical tests, shock attenuation tests, puck impact tests, penetration resistance tests, and neck strap retention test shall be performed to meet the requirements specified.
SCOPE
1.1 This performance specification covers performance requirements for ice hockey goaltender head and face protectors.
1.2 The intent of this performance specification is to reduce the risk of injury to the head and face of ice hockey goaltenders without compromising the form and appeal of the game.
1.3 This specification has requirements for: (1) materials, assembly, and design; (2) protected areas (coverage) and penetration resistance; (3) shock absorption; (4) puck impact resistance; (5) extensibility and strength of the chin strap and its attachment; and (6) optical quality.
1.4 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers performance requirements and test methods for face protectors marketed, sold, and intended for ice hockey.
1.2 The intent of this specification is to reduce the risk of injury to the face without compromising the form or appeal of the game. To do so, the face protector shall be used:
1.2.1 As intended within the rules of the game and
1.2.2 In accordance with the manufacturer’s instructions.
1.3 Ice hockey is a sport with intrinsic hazards associated with the normal conduct of the game. Participation in ice hockey implies the acceptance of some risk of injury. Use of a face protector certified to this specification will not prevent all injuries.
1.4 This specification has been prepared after careful consideration of the frequency and mechanisms associated with facial and eye injuries that can potentially occur within the rules of the game of ice hockey.
1.5 Requirements and the corresponding test methods, where appropriate, are given for the following:
1.5.1 Construction,
1.5.2 Puck impact resistance,
1.5.3 Penetration,
1.5.4 Field of vision, and
1.5.5 Marking and information.
1.6 Face protection is intended for use by players, goalkeepers, and certain functionaries (for example, referees and coaches). Types of protectors considered under this specification are:
1.6.1 Type B1—A full-face protector intended for use by persons older than ten years of age, other than goaltenders;
1.6.2 Type B2—A full-face protector intended for use by persons ten years of age or younger, other than goaltenders; and
1.6.3 Type C (Visor)—A visor intended for use by person in the junior age category and older, other than goaltenders.
1.7 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.
1.8 Use of the singular does not exclude the plural (and vice versa) when the sense allows.
1.9 Although the intended primary application of this specification is stated in this scope, note that it remains the responsibility of the users of this specification to judge its suitability for their particular purpose.
1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This performance specification covers performance requirements for ice hockey helmets.
1.2 The intent of this performance specification is to reduce the risk of injury to the head without compromising the form and appeal of the game.
1.3 This performance specification covers: (1) performance tests for shock absorption properties of the complete helmet and strength and elongation of the chin strap and its attachment; and (2) requirements for area of coverage and penetration.
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
The following precautionary caveat pertains only to the test methods portion, Section 12, of this performance specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers eye and face protective equipment for hockey players.
1.2 This specification is intended to reduce the demonstrated hazards associated with the sport of ice hockey involving the face including eyes.
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
The following precautionary caveat pertains only to the test method portion, Section 7 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This performance specification covers performance requirements for ice hockey helmets.
1.2 The intent of this performance specification is to reduce the risk of injury to the head without compromising the form and appeal of the game.
1.3 This performance specification covers: (1) performance tests for shock absorption properties of the complete helmet and strength and elongation of the chin strap and its attachment; and (2) requirements for area of coverage and penetration.
1.4 The values as stated in inch-pound units are to be regarded as the standard. The values in parentheses are given for information only.
1.5 The following precautionary caveat pertains only to the test methods portion, Section 12, of this performance specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This document covers specifications and conformity assessment methods for new head and face protectors for ice hockey goaltenders, as offered for initial sale. This specification is intended to reduce the risk of injury associated with playing the position of goaltender in ice hockey. The protectors are classified according to types: Type I and Type II. Optical tests, shock attenuation tests, puck impact tests, penetration resistance tests, and neck strap retention test shall be performed to meet the requirements specified.
SCOPE
1.1 This document covers specifications and conformity assessment methods for new head and face protectors for ice hockey goaltenders, as offered for initial sale.
1.2 This specification is intended to reduce the risk of injury associated with playing the position of goaltender in ice hockey.
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

SCOPE
1.1 This performance specification covers performance requirements for ice hockey helmets.
1.2 The intent of this performance specification is to reduce the risk of injury to the head without compromising the form and appeal of the game.
1.3 This performance specification covers: (1) performance tests for shock absorption properties of the complete helmet and strength and elongation of the chin strap and its attachment; and (2) requirements for area of coverage and penetration.
1.4 The values as stated in inch-pound units are to be regarded as the standard. The values in parentheses are given for information only.
1.5 The following precautionary caveat pertains only to the test methods portion, Section 12, of this performance specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers eye and face protective equipment for hockey players.  
1.2 This specification is intended to reduce the demonstrated hazards associated with the sport of ice hockey involving the face including eyes.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 The following precautionary caveat pertains only to the test method portion, Section 7 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This performance specification sets performance requirements for ice hockey helmets.  
1.2 The intent of this performance specification is to reduce the risk of injury to the head without compromising the form and appeal of the game.  
1.3 This performance specification covers (1) performance tests for shock absorption properties of the complete helmet and strength and elongation of the chin strap and its attachment; and (2) requirements for dimension of the ear aperture.  
1.4 The values as stated in inch-pound units are to be regarded as the standard. The values in parentheses are given for information only.  
1.5 The following precautionary caveat pertains only to the test methods portion, Section 12, of this performance specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This standard covers specifications and conformity assessment methods for new head and face protectors for ice hockey goaltenders, as offered for initial sale.  
1.2 This specification is intended to reduce the risk of injury associated with playing the position of goaltender in ice hockey.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

SCOPE
1.1 This performance specification covers skate blades used in the sport of ice hockey.  
1.2 This performance specification is designed to outline acceptable performance requirements without restricting the use of specific materials or construction.  
1.3 This performance specification covers classes of skate blades used by hockey players excluding those used by goalkeepers.  
1.4 The values stated in SI units are to be regarded as the standard. Inch-pound units in parenthesis are listed for information only.  
1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.