SIST EN 14398-2:2004
(Main)Cryogenic vessels - Large transportable non-vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing
Cryogenic vessels - Large transportable non-vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing
This European Standard specifies requirements for the design, fabrication, inspection and testing of large transportable non vacuum insulated cryogenic vessels of more than 1000 l volume, which are permanently (fixed tanks) or not permanently (demountable tanks) attached to a vehicle, for carriage by road. However, it can be used for other mode of transport providing the specific regulations/requirements are complied with.
This European Standard applies to large transportable non vacuum insulated cryogenic vessels for fluids specified in prEN 14398-1 and does not apply to vessels designed for toxic fluids.
This European Standard does not include the general vehicle requirements e.g. running gear, brakes, lighting etc. that shall be in accordance with the relevant standards/regulations.
Kryo-Behälter - Große ortsbewegliche, nicht vakuum-isolierte Behälter - Teil 2: Bemessung, Herstellung, Überwachung und Prüfung
Diese Europäische Norm gilt für die Bemessung, Herstellung und Prüfung von großen ortsbeweglichen, nicht vakuum-isolierten Kryo-Behältern mit einem Fassungsraum von mehr als 1 000 Litern für festverbundene Tanks (von Tank- oder Schienenfahrzeugen), Aufsetztanks, Tanks von Batterie-Fahrzeugen und Tankcontainern (TC) für tiefgekühlte verflüssigte Gase im Sinne der Regelungen für die Beförderung gefährlicher Güter.
Diese Norm gilt für große ortsbewegliche, nicht vakuum-isolierte Kryo-Behälter für Fluide, die in EN 14398-1 festgelegt sind, und sie gilt nicht für giftige Fluide.
Diese Europäische Norm enthält keine allgemeinen Anforderungen an Fahrzeuge wie z. B. an Fahrgestell, Bremsen, Beleuchtung usw., diese müssen mit den relevanten Normen/Gesetzen übereinstimmen.
Récipients cryogéniques - Grands récipients transportables non isolés sous vide - Partie 2: Conception, fabrication, inspection et essais
La présente Norme européenne spécifie des exigences en matière de conception, fabrication, contrôle et essais de grands récipients cryogéniques transportables non isolés sous vide d'un volume supérieur à 1 000 l, fixés sur un véhicule de manière permanente (réservoirs fixes) ou non (réservoirs démontables) pour le transport routier. Elle peut cependant être utilisée pour d'autres modes de transport à condition que soient respectées les lois et exigences correspondantes.
La présente Norme européenne s'applique aux grands récipients cryogéniques transportables non isolés sous vide pour les fluides spécifiés dans l'EN 14398-1 et ne s'applique pas à des récipients prévus pour contenir des fluides toxiques.
La présente Norme européenne ne couvre pas les exigences générales relatives aux véhicules, par exemple, les organes de roulement, les freins, les feux, etc., qui doivent être conformes aux normes/règlements correspondants.
Kriogene posode – Velike premične, vakuumsko neizolirane posode - 2. del: Konstruiranje, izdelava, kontrola in preskus
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cryogenic vessels - Large transportable non-vacuum insulated vessels - Part 2: Design, fabrication, inspection and testingRécipients cryogéniques - Grands récipients transportables non isolés sous vide - Partie 2: Conception, fabrication, inspection et essaisKryo-Behälter - Große ortsbewegliche, nicht vakuum-isolierte Behälter - Teil 2: Bemessung, Herstellung, Überwachung und PrüfungTa slovenski standard je istoveten z:EN 14398-2:2003SIST EN 14398-2:2004en23.020.40ICS:SLOVENSKI
STANDARDSIST EN 14398-2:200401-junij-2004
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14398-2August 2003ICS 23.020.40English versionCryogenic vessels - Large transportable non-vacuum insulatedvessels - Part 2: Design, fabrication, inspection and testingRécipients cryogéniques - Grands récipients transportablesnon isolés sous vide - Partie 2: Conception, fabrication,inspection et essaisKryo-Behälter - Große ortsbewegliche, nicht vakuum-isolierte Behälter - Teil 2: Bemessung, Herstellung,Überwachung und PrüfungThis European Standard was approved by CEN on 10 July 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14398-2:2003 E
Elastic stress analysis.65A.1General.65A.2Terminology.65A.2.1Stress intensity.65A.2.2Gross structural discontinuity.66A.2.3Local structural discontinuity.66A.2.4Normal stress.66A.2.5Shear stress.66A.2.6Membrane stress.66A.2.7Primary stress.67A.2.8Primary local membrane stress.67A.2.9Secondary stress.67A.2.10Peak stress.67A.3Limit for longitudinal compressive general membrane stress.67A.4Stress categories and stress limits for general application.68A.4.1General.68A.4.2General primary membrane stress category.68A.4.3Local primary membrane stress category.68A.4.4General or local primary me
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.