SIST EN ISO 20567-2:2017

SLOVENSKI STANDARD
01-maj-2017
1DGRPHãþD
SIST EN ISO 20567-2:2007
Barve in laki - Ugotavljanje odpornosti premazov proti udarcem kamenja - 2. del:
Preskus z enim udarcem vodenega telesa (ISO 20567-2:2017)
Paints and varnishes - Determination of stone-chip resistance of coatings - Part 2: Single
-impact test with a guided impact body (ISO 20567-2:2017)
Beschichtungsstoffe - Prüfung der Steinschlagfestigkeit von Beschichtungen - Teil 2:
Einzelschlagprüfung mit geführtem Schlagkörper (ISO 20567-2:2017)
Peintures et vernis - Détermination de la résistance des revêtements aux impacts de
cailloux - Partie 2: Essai de choc simple par corps percutant guidé (ISO 20567-2:2017)
Ta slovenski standard je istoveten z: EN ISO 20567-2:2017
ICS:
87.040 Barve in laki Paints and varnishes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 20567-2
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2017
EUROPÄISCHE NORM
ICS 87.040 Supersedes EN ISO 20567-2:2006
English Version
Paints and varnishes - Determination of stone-chip
resistance of coatings - Part 2: Single-impact test with a
guided impact body (ISO 20567-2:2017)
Peintures et vernis - Détermination de la résistance des Beschichtungsstoffe - Prüfung der Steinschlagfestigkeit
revêtements aux impacts de cailloux - Partie 2: Essais von Beschichtungen - Teil 2: Einzelschlagprüfung mit
de chocs simple par corps percutant guidé (ISO 20567- geführtem Schlagkörper (ISO 20567-2:2017)
2:2017)
This European Standard was approved by CEN on 5 November 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 20567-2:2017 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 20567-2:2017) has been prepared by Technical Committee ISO/TC 35 "Paints
and varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2017 and conflicting national standards shall
be withdrawn at the latest by August 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 20567-2:2006.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 20567-2:2017 has been approved by CEN as EN ISO 20567-2:2017 without any
modification.
INTERNATIONAL ISO
STANDARD 20567-2
Second edition
2017-01
Paints and varnishes — Determination
of stone-chip resistance of coatings —
Part 2:
Single-impact test with a guided
impact body
Peintures et vernis — Détermination de la résistance des revêtements
aux impacts de cailloux —
Partie 2: Essai de choc simple par corps percutant guidé
Reference number
ISO 20567-2:2017(E)
©
ISO 2017
ISO 20567-2:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

ISO 20567-2:2017(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus and materials. 2
6 Test panels . 2
6.1 Substrate . 2
6.2 Preparation and coating . . 2
6.3 Thickness of the coating . 2
7 Procedure. 4
7.1 Calibration . 4
7.2 Conditioning of the test panels . 4
7.3 Test conditions . 4
7.4 Number of test runs . 4
7.5 Determination . 5
8 Evaluation . 5
9 Precision . 6
9.1 Repeatability limit, r .6
9.2 Reproducibility limit, R .6
10 Test report . 7
Annex A (informative) Examples of suitable procedures for removing loose paint .8
Annex B (normative) Calibration of the test apparatus . 9
ISO 20567-2:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.
The committee responsible for this document is ISO/TC 35, Paints and varnishes, Subcommittee SC 9,
General test methods for paints and varnishes.
This second edition cancels and replaces the first edition (ISO 20567-2:2005), which has been technically
revised with the following main changes:
— a specification has been added, when the calibration of the apparatus shall be made;
— reference to optical imaging has been deleted;
— the clause on sampling has been deleted;
— the description of suitable methods for removal of loose paint have been transferred to an informative
annex as examples, and, for the method using adhesive tape, the adhesive strength of the tape is no
longer specified;
— some minor corrections have been made;
— this document is revised editorially and the normative references have been updated.
A list of all parts in the ISO 20567 series can be found on the ISO website.
iv © ISO 2017 – All rights reserved

ISO 20567-2:2017(E)
Introduction
In the automobile industry, multi-layer paint coatings are applied to car bodies for protection. Grit,
road-metal and other materials can damage these coatings in such a way that individual layers come off
or the whole coating delaminates from the substrate.
Stone chipping can be simulated by means of single- and/or multi-impact tests. ISO 20567-1 describes
multi-impact testing; ISO 20567-2 and I
...