SIST EN ISO 14529-3:2000

SLOVENSKI STANDARD
01-december-2000
Polimerni materiali - Melamin/fenolne praškaste zmesi za oblikovanje (MF- PMCS) -
3. del: Zahteve za izbrane zmesi za oblikovanje (ISO 14529-3:1999)
Plastics - Melamine/phenolic powder moulding compounds (MP-PMCs) - Part 3:
Requirements for selected moulding compounds (ISO 14529-3:1999)
Plastiques - Poudres a mouler a base de mélamine/phénol (MP-PMC) - Partie 3:
Exigences relatives a certaines poudres a mouler (ISO 14529-3:1999)
Ta slovenski standard je istoveten z: EN ISO 14529-3:1999
ICS:
83.080.10 Duromeri Thermosetting materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

INTERNATIONAL ISO
STANDARD 14529-3
First edition
1999-11-15
Plastics — Melamine/phenolic powder
moulding compounds (MP-PMCs) —
Part 3:
Requirements for selected moulding
compounds
Plastiques — Poudres à mouler à base de mélamine/phénol (MP-PMC) —
Partie 3: Exigences relatives à certaines poudres à mouler
Reference number
ISO 14529-3:1999(E)
©
ISO 1999
ISO 14529-3:1999(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 1999
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 1999 – All rights reserved

ISO 14529-3:1999(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 14529 may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 14529-3 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee
SC 12, Thermosetting materials.
After a transition period of, at the most, four years, the three parts of ISO 14529 (see below) will replace
ISO 4896:1990, of which they constitute a technical revision.
ISO 14529 consists of the following parts, under the general title Plastics — Melamine/phenolic powder moulding
compounds (MP-PMCs):
� Part 1: Designation system and basis for specifications
� Part 2: Preparation of test specimens and determination of properties
� Part 3: Requirements for selected moulding compounds
Annex A of this part of ISO 14529 is for information only.
© ISO 1999 – All rights reserved iii

INTERNATIONAL STANDARD ISO 14529-3:1999(E)
Plastics — Melamine/phenolic powder moulding compounds
(MP-PMCs) —
Part 3:
Requirements for selected moulding compounds
1 Scope
This part of ISO 14529 specifies the requirements for the physical and chemical properties of phenolic powder
moulding compounds (MP-PMCs) and compression- or injection-moulded test specimens produced from them.
It is limited to those powder moulding compounds whose composition and properties are significantly different. It is
further limited to those moulding compounds which are of general technical and/or economic importance.
The properties which are used to characterize the moulding compounds, the test methods and the test conditions
are selected from those given in ISO 14529-2.
The moulding compounds are divided into types according to their composition and properties. The various types
are designated using the designation system defined in ISO 14529-1.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this part of ISO 14529. For dated references, subsequent amendments to, or revisions of, any of these publications
do not apply. However, parties to agreements based on this part of ISO 14529 are encouraged to investigate the
possibility of applying the most recent editions of the normative documents indicated below. For undated
references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain
registers of currently valid International Standards.
ISO 472:1999, Plastics — Vocabulary.
ISO 4896:1990,
...