SIST EN 12838:2003
(Main)Installations and equipment for liquefied natural gas - Suitability testing of LNG sampling systems
Installations and equipment for liquefied natural gas - Suitability testing of LNG sampling systems
This standard specifies the tests to be carried out in order to assess the suitability of LNG sampling systems designed, in combination with an analytical device such as a chromatograph, to determine the composition of Liquefied Natural Gas.
Anlagen und Ausrüstung für Flüssigerdgas - Eignungsprüfung von Flüssigerdgas-Probenahmesystemen
Diese Norm legt Prüfungen zur Beurteilung der Eignung von Flüssigerdgas(LNG)- Probenahmesystemen fest, die mit einem Analysegerät, z.B. einem Chromatographen, kombiniert und dafür ausgelegt sind, die Zusammensetzung des Flüssigerdgases zu bestimmen.
Installations et équipements relatifs au gaz naturel liquéfié - Essais d'aptitude a l'emploi des systemes d'échantillonnage du GNL
La présente norme européenne prescrit les essais devant être réalisés afin d'évaluer l'aptitude à l'emploi des systèmes d'échantillonnage du GNL qui, associés avec un appareil d'analyse tel qu'un chromatographe, permettent de déterminer la composition du Gaz Naturel Liquéfié.
Napeljave in oprema za utekočinjeni zemeljski plin - Preskušanje ustreznosti - Sistemi za vzorčenje
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Anlagen und Ausrüstung für Flüssigerdgas - Eignungsprüfung von Flüssigerdgas-ProbenahmesystemenInstallations et équipements relatifs au gaz naturel liquéfié - Essais d'aptitude a l'emploi des systemes d'échantillonnage du GNLInstallations and equipment for liquefied natural gas - Suitability testing of LNG sampling systems75.200Petroleum products and natural gas handling equipmentICS:Ta slovenski standard je istoveten z:EN 12838:2000SIST EN 12838:2003en01-januar-2003SIST EN 12838:2003SLOVENSKI
STANDARD
SIST EN
...
This May Also Interest You
This document describes the specific functional requirements for the design, construction, operation, maintenance and disposal activities for safe and secure gas compressor stations.
This document applies to new gas compressor stations with a Maximum Operating Pressure (MOP) over 16 bar and with a total shaft power over 1 MW. For existing compressor stations, this document applies to new compressor units. Where changes/modifications to existing installations or gas composition take place, due account can be taken of the requirements of this document.
This document does not apply to gas compressor stations or compressor units operating prior to the publication of this document. For existing sites this document can be used as guidance.
The purpose of this document is to:
— ensure the health and safety of the public and all site personnel;
— cover environmental issues;
— avoid incidental damage to nearby property; and
— open the gas infrastructure to accommodate renewable gases, including a possible design for hydrogen.
This document specifies common basic principles for the gas infrastructure. Users of this document are expected to be aware that more detailed national standards and/or codes of practice can exist in the CEN member countries.
This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this document, the national legislation/regulation takes precedence as illustrated in CEN/TR 13737 (all parts). CEN/TR 13737 (all parts) gives:
— clarification of all legislations/regulations applicable in a member state;
— if appropriate, more restrictive national requirements;
— a national contact point for the latest information.
This document does not apply to:
— off-shore gas compressor stations;
— gas compressor stations for compressed gas filling-stations;
— customer installations downstream of the point of custody transfer;
— design and construction of driver packages (see Annex C);
— mobile compressor equipment.
For supplies to utility services such as small central heating boilers reference is made to EN 1775.
Figure 1 shows a schematic representation of compressor stations in a gas infrastructure. For further information refer to Annexes A, B, C, D, E and F.
[Figure 1]
- Standard65 pagesEnglish languagesale 10% offe-Library read for×1 day
- 07-Jan-2025
- 23.140
- 75.200
- 2002-01-1152
- M/017
- DPL
This document establishes the functional requirements for stations for the injection of biomethane, substitute natural gas (SNG) and hydrogen into gas transmission and distribution systems operated with gases (natural gas, biomethane, SNG, hydrogen, gas mixtures) in accordance with European technical rules that ensure the interoperability of systems.
Figure 1 describes the general approach including all the relevant functions that can be installed in different configurations. The injection of Hydrogen is covered separately in EN 17928-3:2024.
This document also applies to refeeding stations that feed such gases back into upstream gas supply networks; see Figure 2.
This document represents the state of the art at the time of its preparation.
This document does not apply to injection stations operating prior to the publication of this document.
This document specifies common basic principles for gas infrastructure. Users of this document are expected to be aware that more detailed national standards and/or codes of practice can exist in the CEN member countries. This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of terms of additional requirements in national legislation/regulation than in this document, CEN/TR 13737 (all parts) illustrates these terms.
CEN/TR 13737 (all parts) gives:
— legislation/regulations applicable in a member state;
— if appropriate, more restrictive national requirements;
— a national contact point for the latest information.
- Standard59 pagesEnglish languagesale 10% offe-Library read for×1 day
This document establishes specific functional requirements of stations for the injection of hydrogen into transmission and distribution systems for fuel gases (natural gas, biomethane, SNG, hydrogen, fuel gas mixtures, etc.; see Figure 1) in accordance with European technical rules that ensure the interoperability of systems in addition to the general functional requirements of EN 17928 1:2024.
This document complements EN 17928 1:2024 by specifying the technical safety requirements to be observed with respect to the chemical and physical properties of hydrogen.
It furthermore complements the requirements on pipelines specified in EN 12007 3 and EN 1594 by describing the specific requirements with respect to hydrogen.
Additionally, it explains how to handle hydrogen measurements during the course of injection.
Dedicated requirements for the technical equipment of the gas transmission and distribution network for mixing hydrogen as an additive gas into the gas flow after the injection station are not covered by this document. However, requirements for the resulting gas mixture and the related coordination and interfaces between station and network operation are specified in this document.
This document represents the recommendations at the time of its preparation. This document does not apply to injection stations operating prior to the publication of this document.
This document specifies common basic principles for gas infrastructure. Users of this document are expected to be aware that more detailed national standards and/or codes of practice can exist in the CEN member countries. This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of terms of additional requirements in national legislation/regulation than in this document, CEN/TR 13737 (all parts) illustrates these terms.
CEN/TR 13737 (all parts) gives:
— legislation/regulations applicable in a member state;
— if appropriate, more restrictive national requirements;
— a national contact point for the latest information.
- Standard10 pagesEnglish languagesale 10% offe-Library read for×1 day
This document provides requirements and recommendations for the design, construction and operation of newly installed liquefied natural gas (LNG) railway loading and unloading facilities for use on onshore LNG terminals, LNG satellite plants, handling LNG tank wagons or tank containers engaged in international trade.
The designated boundary limits of this document are between the LNG terminal’s inlet/outlet piping headers at the beginning of the rail loading or unloading area and the rail track area used for LNG tank wagons and containers. It is applicable to all rail loading bays, weighbridge(s) and related subsystems.
- Standard25 pagesEnglish languagesale 10% offe-Library read for×1 day
This document gives guidelines for safe fuelling operations of vehicles that use liquefied natural gas (LNG) as a fuel for propulsion, covering the activities and procedures to be followed for safe operation. It provides procedures applicable to different fuelling systems and technologies.
NOTE Regarding the responsibility surrounding the training of drivers of LNG vehicles, see the framework of Directive 89/391 EEC.
- Standard12 pagesEnglish languagesale 10% offe-Library read for×1 day
This document establishes specific functional requirements for injection stations for biomethane into gas transmission and distribution systems operated with gases of the second gas family in accordance with EN 437 in addition to the general functional requirements of EN 17928 1:2024.
This document represents the recommendations at the time of its preparation. This document does not apply to injection stations operating prior to the publication of this document.
This document complements EN 17928 1:2024 by specifying the technical safety requirements to be observed in respect of the chemical and physical properties of biomethane.
This document specifies common basic principles for gas infrastructure. Users of this document are expected to be aware that more detailed national standards and/or codes of practice can exist in the CEN member countries.
This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of terms of additional requirements in national legislation/regulation than in this document, CEN/TR 13737 (all parts) illustrates these terms.
CEN/TR 13737 (all parts) gives:
— legislation/regulations applicable in a member state;
— if appropriate, more restrictive national requirements;
— a national contact point for the latest information.
- Standard7 pagesEnglish languagesale 10% offe-Library read for×1 day
This document provides requirements for operation of vehicles that use liquefied natural gas (LNG) as a fuel for propulsion, covering various aspects of LNGV workshops including activities, risk management, planning, personnel, layout, systems and operations. It provides requirements regarding the management of LNGV including use, parking, fuelling for commissioning, inspection, installation, repair and maintenance, disposal, transportation and documentation.
This document is applicable to the management of LNG vehicles.
- Standard30 pagesEnglish languagesale 10% offe-Library read for×1 day
This document describes the functional requirements for pipelines for maximum operating pressure over 16 bar. This document also describes the mechanical requirements for pipework in stations with a maximum operating pressure greater than 16 bar.
NOTE 1 Welding requirements are described in EN 12732. Functional requirements for stations are given in EN 1776, EN 1918-5, EN 12186, and EN 12583.
This document is applicable for transporting gas via onshore high-pressure steel pipeline infrastructures, where the following applies:
- onshore:
- from the point where the pipeline first crosses what is normally accepted as battery limit between onshore and offshore, and that is not located within commercial or industrial premises as an integral part of the industrial process on these premises except for any pipelines and facilities supplying such premises;
- pipeline system with a starting point onshore, also when parts of the pipeline system on the mainland subsequently cross fjords, lakes, etc.
- high pressure: gas with a maximum operating pressure over 16 bar and a design temperature between −40 °C and 120 °C.
- steel pipeline infrastructure: infrastructure consisting of pipeline components, such as pipes, valves, couplings and other equipment, restricted to components made of unalloyed or low alloyed carbon steel and joined by welds, flanges or mechanical couplings.
- gas: non-corrosive natural gas, biomethane gas, hydrogen gas and mixtures of these gases where technical evaluation has ensured that operating conditions or constituents or properties of the gas do not affect the safe operation of the pipeline.
Gas infrastructures covered by this document begin after the gas producer's metering station.
NOTE 2 The functional demarcation of the pipeline system is usually directly after an isolating valve of the installation, but can differ in particular situations. The functional demarcation of the pipeline system is usually located on an isolating valve of the installation, but can differ in particular situations.
A schematic representation of pipelines for gas infrastructure is given in Figure 1.
This document can also be applied to the repurposing of existing pipelines.
[Figure 1 - Schematic representation of pipelines for gas supply over 16 bar]
This document specifies common basic principles for gas infrastructure. Users of this standard are expected to be aware that more detailed national standards and/or code of practice can exist in the CEN member countries.
This document is intended to be applied in association with these national standards and/or codes of practice setting out the above-mentioned basic principles.
In the event of conflicts in terms of more restrictive requirements in national legislation/regulation with the requirements of this standard, the national legislation/regulation takes precedence as illustrated in CEN/TR 13737.
CEN/TR 13737 gives:
- clarification of all legislations/regulations applicable in a member state;
- if appropriate, more restrictive national requirements;
- a national contact point for the latest information.
- Standard69 pagesEnglish languagesale 10% offe-Library read for×1 day
This document specifies the minimum safety interface requirement for the unloading stop system between the LNG road tanker and LNG fuelling station.
This document consists of two main topics:
- functional description of the unloading stop system;
- technical layout description of the unloading stop system.
- Standard12 pagesEnglish languagesale 10% offe-Library read for×1 day
- 02-Feb-2023
- 12-Jun-2024
- 43.040.01
- 75.200
- 2014/94/EU
- DPL
This document specifies a harmonized unloading connector for LNG road tanker at LNG fuelling stations. This document is also applicable to LNG RID applications. While LNG is also transported by rail, European regulations are organized through the International Carriage of Dangerous Goods by Rail (RID). The same configuration as defined by this document, can be utilized. This document includes requirements for (at least):
- functional description of the LNG unloading receptacle and LNG unloading nozzle;
- technical layout description of the LNG unloading receptacle.
The technical layout description of the LNG unloading nozzle is not part of this document.
The basic functional requirement of the LNG unloading connector are as follows:
- to prevent leakage of methane during operation and in particular during disconnecting;
- easy handling, no spillage and purging with nitrogen during disconnecting.
The loading connector between the LNG road tanker and the LNG terminal is not covered by this document.
See Figure 1.
- Standard21 pagesEnglish languagesale 10% offe-Library read for×1 day
- 02-Feb-2023
- 12-Jun-2024
- 43.040.01
- 75.200
- 2014/94/EU
- DPL
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.