EN 13286-50:2004

SLOVENSKI STANDARD
01-junij-2005
Nevezane in hidravlično vezane zmesi – 50. del: Postopek (metoda) za pripravo
preizkušancev iz hidravlično vezanih zmesii, zgoščenih po Proctorjevem postopku
ali vibracijsko mizo
Unbound and hydraulically bound mixtures - Part 50: Method for the manufacture of test
specimens of hydraulically bound mixtures using Proctor equipment or vibrating table
compaction
Ungebundene und hydraulisch gebundene Gemische - Teil 50: Verfahren zur
Herstellung von Probekörpern von hydraulisch gebundenen Gemischen durch
Verdichtung mit Proctorgerät oder Vibrationstisch
Mélanges traités et mélanges non traités aux liants hydrauliques - Partie 50: Méthode de
confection par compactage avec un appareillage Proctor ou une table vibrante des
éprouvettes de matériaux traités aux liants hydrauliques
Ta slovenski standard je istoveten z: EN 13286-50:2004
ICS:
93.080.20 Materiali za gradnjo cest Road construction materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 13286-50
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2004
ICS 93.080.20
English version
Unbound and hydraulically bound mixtures - Part 50: Method for
the manufacture of test specimens of hydraulically bound
mixtures using Proctor equipment or vibrating table compaction
Mélanges traités et mélanges non traités aux liants Ungebundene und hydraulisch gebundene Gemische - Teil
hydrauliques - Partie 50: Méthode de confection par 50: Verfahren zur Herstellung von Probekörpern von
compactage avec un appareillage Proctor ou une table hydraulisch gebundenen Gemischen durch Verdichtung mit
vibrante des éprouvettes de matériaux traités aux liants Proctorgerät oder Vibrationstisch
hydrauliques
This European Standard was approved by CEN on 12 November 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13286-50:2004: E
worldwide for CEN national Members.

Contents
Page
Foreword.3
1 Scope .5
2 Normative references .5
3 Terms and definitions .5
4 Principle.5
5 Dimensions of the specimens.5
6 Apparatus .6
7 Procedure .6
8 Storage.7
9 Test report .7

Foreword
This document (EN 13286-50:2004) has been prepared by Technical Committee CEN/TC 227 “Road
materials”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2005, and conflicting national standards shall be withdrawn at
the latest by June 2005.
This document is one of a series of documents as listed below.
EN 13286-1, Unbound and hydraulically bound mixtures  Part 1: Test methods for laboratory reference
density and water content  Introduction, general requirements and sampling
EN 13286-2, Unbound and hydraulically bound mixtures  Part 2: Test methods for the determination of the
laboratory reference density and water content  Proctor compaction
EN 13286-3, Unbound and hydraulically bound mixtures  Part 3: Test methods for laboratory reference
density and water content  Vibrocompression with controlled parameters
EN 13286-4, Unbound and hydraulically bound mixtures  Part 4: Test methods for laboratory reference
density and water content  Vibrating hammer
EN 13286-5, Unbound and hydraulically bound mixtures  Part 5: Test methods for laboratory reference
density and water content  Vibrating table
EN 13286-7, Unbound and hydraulically bound mixtures  Part 7: Cyclic load triaxial test for unbound
mixtures
EN 13286-40, Unbound and hydraulically bound mixtures  Part 40: Test method for the determination of the
direct tensile strength of hydraulically bound mixtures
EN 13286-41, Unbound and hydraulically bound mixtures  Part 41: Test method for the determination of the
compressive strength of hydraulically bound mixtures
EN 13286-42, Unbound and hydraulically bound mixtures  Part 42: Test method for the determination of the
indirect tensile strength of hydraulically bound mixtures
EN 13286-43, Unbound and hydraulically bound mixtures  Part 43: Test method for the determination of the
modulus of elasticity of hydraulically bound mixtures
EN 13286-44, Unbound and hydraulically bound mixtures  Part 44: Test method for the determination of the
alpha coefficient of vitrified blast furnace slag
EN 13286-45, Unbound and hydraulically bound mixtures  Part 45: Test method for the determination of the
workability period of hydraulically bound mixtures
EN 13286-46, Unbound and hydraulically bound mixtures  Part 46: Test method for the determination of the
moisture condition value
EN 13286-47, Unbound and hydraulically bound mixtures  Part 47: Test method for the deter
...