EN ISO 8100-1:2026
(Main)Lifts for the transport of persons and goods - Part 1: Safety rules for the construction and installation of passenger and goods passenger lifts (ISO 8100-1:2026, including corrected version 2026-05)
- Abstract
This document specifies the safety rules for lifts permanently serving buildings and constructions and intended for the transport of persons or persons and goods. It applies to traction lifts, positive drive lifts and hydraulic lifts that:
serve specific levels; and
have a rated speed exceeding 0,15 m/s; and
have an enclosed car; and
move along guide rails inclined not more than 15° to the vertical; and
are indoor or weather-protected.
This document also applies to the electrical equipment of these lifts including the lighting and socket outlets in the well.
This document specifies safety rules related to:
persons to be safeguarded:
users, including passengers, maintenance and inspection personnel;
persons at the landings and outside of the well, or any machinery space and pulley room, who can be affected by the lift.
property to be safeguarded:
loads in the car;
components of the lift installation;
building in which the lift is installed.
This document does not specify additional requirements for:
lifts serving buildings with requirements for seismic conditions;
lifts serving buildings with requirements for accessibility;
lifts exposed to vandalism;
lifts which can be used for firefighting and evacuation purposes under firefighters control;
lifts which can be used to support faster evacuation of persons with disabilities;
the behaviour of the lift when the control system of the lift receives a recall signal(s) in the event of fire in a building.
This document is not applicable to passenger and goods passenger lifts, which are installed before the date of its publication.
- Status
- Published
- Publication Date
- 16-Jun-2026
- Technical Committee
- CEN/TC 10 - Passenger, goods and service lifts
- Drafting Committee
- CEN/TC 10/WG 1 - Lifts and service lifts
- Current Stage
- 6060 - Definitive text made available (DAV) - Publishing
- Start Date
- 17-Jun-2026
- Due Date
- 09-Oct-2024
- Completion Date
- 17-Jun-2026
EN ISO 8100-1:2026 is a CEN European Standard that sets safety rules for the construction and installation of passenger and goods passenger lifts. It covers traction lifts, positive drive lifts and hydraulic lifts in buildings, including the electrical equipment in the well, and it is written for the people who design, install, inspect and maintain these lifts.
The standard focuses on the hazards that matter in practice: protecting users and maintenance personnel, preventing falls and crushing, controlling overspeed and unintended movement, and making sure the lift and the building interface are designed together.
What does EN ISO 8100-1:2026 specify?
EN ISO 8100-1:2026 specifies safety rules for lifts permanently serving buildings and constructions, intended to carry persons or persons and goods. It applies to lifts with specific-level service, a rated speed above 0,15 m/s, an enclosed car, guide rails inclined not more than 15° to the vertical, and indoor or weather-protected installation.
The document also covers the lift’s electrical equipment, including lighting and socket outlets in the well. It is aimed at protecting users, maintenance and inspection personnel, people at landings and outside the well, and the building and lift components.
It excludes special additional requirements for seismic conditions, accessibility requirements, vandalism exposure, firefighting or evacuation use under firefighters control, faster evacuation of persons with disabilities, and fire-recall behaviour. It is not applicable to passenger and goods passenger lifts installed before publication.
The document is organised into:
- Clause 1 - Scope
- Clause 2 - Normative references
- Clause 3 - Terms and definitions
- Clause 4 - Safety requirements and/or protective measures
- Clause 5 - Verification of the safety requirements and/or protective measures
- Clause 6 - Information for use
- Clause 7 - Use of ISO/TS 8100-3
- Annex A - Normative list of electric safety devices
- Annex B - Normative technical interfaces with the building
- Annex C - Normative pit access ladder provisions
- Annex D - Informative relationship with ISO 8100-20
| Annex | What it covers |
|---|---|
| Annex A | Electric safety devices and their minimum SIL |
| Annex B | Technical interfaces between the lift and the building or construction |
| Annex C | Types of pit access ladder and their dimensional and safety provisions |
| Annex D | Relationship between this document and ISO 8100-20 |
What are the key requirements of EN ISO 8100-1:2026?
EN ISO 8100-1:2026 sets requirements for the whole lift system, from the well and doors to the machine, controls and verification. The most important points are the barriers around moving parts, the protective devices that stop unsafe motion, and the checks used before a lift is put into service.
General protection, markings and building interface
Clause 4.1 requires the lift to comply with the safety requirements and protective measures in the document. It also requires guards to be fixed securely, and labels, notices, markings and signs to be permanent, indelible and legible. In practice, this means safety information must stay readable for inspection, maintenance and emergency use.
Annex B sets the technical interfaces with the building. This matters because the lift and the building have to match on layout, access, environmental conditions and loads.
Well, pit, machinery spaces and access
Clause 4.2 covers the well, machinery spaces and pulley rooms. It addresses the arrangement of lift equipment, lighting, electrical equipment in the pit and machinery spaces, emergency release, wall/floor/ceiling strength, access to the pit, pit platforms, notices, enclosure of the well, clearances, refuge spaces on the car roof, and clearances in the headroom and pit.
In practice, these requirements reduce the risk of a person being trapped, crushed, struck or falling when entering the pit, working near machinery or standing on the car roof. Annex C supports this by specifying acceptable pit access ladder types and their positioning.
Doors, door operation and door integrity
Clause 4.3 is one of the largest parts of the document. It requires landing doors at landings, imperforate door construction, limited clearances, door strength, and protection against falling and shearing hazards at the entrances.
For power-operated doors, Clause 4.3 requires obstacle detection, limits on closing force and kinetic energy, automatic re-opening when an obstacle is detected, and warning during door closing for vertical sliding doors. For doors with glass, it requires laminated glass, retention of the glass in the frame, and impact resistance tested by pendulum methods.
The same clause also covers locking, proof of the closed and locked condition, emergency unlocking, and restrictions on opening the car door. In practice, these requirements keep the car from moving unless the doors are secure, and they reduce the chance of someone entering the well or being struck by moving doors.
Car enclosure, load, suspension and movement control
Clause 4.4 sets requirements for the car, including enclosure, available car area, rated load and number of passengers, as well as the apron, roof, ventilation and lighting. The document links car area to rated load, which matters when selecting a lift for the intended passenger capacity.
Clause 4.5 covers suspension means, traction and transmission, tension equalisation, compensation means and marking. It requires independent suspension means and provides rules for monitoring discard condition of suspension means. That is important because suspension wear affects long-term safety and service planning.
Clause 4.6 covers free-fall prevention, overspeed, unintended car movement and creeping. It includes safety gear, rupture valves, restrictors, pawl devices, ascending car overspeed protection and protection against unintended car movement. These are the core safeguards that stop the lift if something goes wrong with speed or support.
Guide rails, buffers, machinery and electrics
Clause 4.7 deals with guiding of the car, counterweight or balancing weight, and with permissible stresses, deflections and load cases. Clause 4.8 covers buffers for the car and counterweight, including stroke requirements. Together, these clauses define how the lift absorbs load and stops within the travel limits.
Clause 4.9 covers lift machinery and associated equipment, including braking, emergency operation and speed-related provisions for traction, positive drive and hydraulic lifts. Clauses 4.10 and 4.11 cover electrical installations, protection against electric faults, and electric safety devices, including safety circuits and SIL-rated circuits.
Clause 4.12 covers controls, final limit switches, load control, levelling, re-levelling, inspection operation, emergency electrical operation, automatic rescue operation, remote alarm and intercom, and operating priorities. In practice, this is the section that tells the installer how the lift is controlled in normal use and in abnormal or emergency conditions.
Verification and information for use
Clause 5 links the safety requirements to verification methods and tests on the installed lift. It includes checks for braking, electrical installation, traction, safety gear, buffers, rupture valve, restrictors, overspeed protection, levelling accuracy, unintended car movement, and door-related safety functions.
Clause 6 requires instructions and a logbook. That means the lift must be handed over with information for use, maintenance and emergency operation, and with a record for repairs and periodic checks.
Clause 7 states that ISO/TS 8100-3:2019, Clause 4, is to be followed when applicable in combination with this document.
What terms does EN ISO 8100-1:2026 define?
- Automatic rescue operation - a device or function that acts automatically after failure or loss of power to move the car to a landing.
- Electric safety device - a safety contact, safety circuit or SIL-rated circuit with the required reliability of operation.
- Hydraulic lift - a lift in which the movement of the car is controlled by flow of fluid.
- Positive drive lift - a lift directly driven without reliance on friction, using a drum and ropes or sprockets with chains or timing belts.
- Safety gear - a mechanical device that stops the car, counterweight or balancing weight in the down direction and keeps it stationary on the guide rails if overspeed or suspension failure occurs.
- Suspension means - all ropes, belts or chains that suspend the car, counterweight or balancing weight.
- Unintended car movement - non-commanded movement of the car with doors open within the door zone away from the landing, excluding loading and unloading.
- Levelling accuracy - the vertical distance between the car sill and the landing sill.
Who uses EN ISO 8100-1:2026?
EN ISO 8100-1:2026 is used by lift manufacturers, designers, installers, maintenance providers, inspection personnel and building project teams. It is also used by buyers, specifiers and quality managers who need to check that a proposed lift matches the intended application.
In practice, they use it to choose the correct lift type, design the pit and machine spaces, select doors and safety devices, verify door and car protections, plan electrical and control systems, and document testing, maintenance and emergency operation.
What changed in EN ISO 8100-1:2026 from the previous edition?
EN ISO 8100-1:2026 replaces SIST EN 81-20:2020. The title page also identifies this publication as including corrected version 2026-05.
Which standards are used with EN ISO 8100-1:2026?
| Standard(s) | What they contribute |
|---|---|
| ISO 12100; ISO 8100-2; ISO/TS 8100-3 | Risk reduction principles, component design/calculation/test rules, and additional requirements when used together with this document |
| ISO 3008-2; EN 81-58; EN 13501-1; EN 13501-6 | Fire-resistance testing and fire classification for landing doors and electric cables |
| ISO 4344; EN 12385-1; EN 12385-5; EN 13411-3; EN 13411-6; EN 13411-7; EN 13411-8 | Requirements for steel wire ropes and their terminations |
| ISO 12543-2; ISO 12543-3; ISO 29584 | Laminated safety glass and pendulum impact testing/classification for glass in doors and car roofs |
| ISO 1219-1; ISO 4413; ISO 6743-4 | Fluid power symbols, hydraulic safety rules and hydraulic oil classification |
| ISO 13857; ISO 14122-3; ISO 14122-4; EN 1993-1-1 | Safety distances, permanent access means and steel structure design |
| ISO 4190-5; ISO 7010; IEC 60417; IEC 60617; IEC 60598-1 | Lift control devices, safety signs, equipment symbols, diagrams and luminaires |
| ISO 8102-1; ISO 8102-2; ISO 8102-20 | EMC emission, EMC immunity and cybersecurity for lift electrical requirements |
| IEC 60204-1; IEC 60364-4-41; IEC 60364-6; IEC 60529; IEC 60664-1; IEC 61310-3; IEC 61508-1; IEC 61800-5-2; IEC 61810-1; IEC 61810-3; IEC 60947-4-1; IEC 60947-5-1; IEC 60947-5-5 | Electrical equipment of machines, electric shock protection, verification, enclosure protection, insulation coordination, actuator location, functional safety, safety drives, relays, contactors and emergency stop devices |
| IEC 60227-6; IEC 60332-1-2; IEC 60332-3-24; IEC 60754-2; IEC 61034-2; EN 50214 | Lift cables and their fire-performance requirements |
| EN 81-28; EN 81-71 | Remote alarm systems and vandal-resistant lift applications |
What does the EN ISO 8100-1:2026 document contain?
EN ISO 8100-1:2026 contains detailed technical clauses, diagrams and tables for lift safety design. It includes load-area and rated-load data, door-clearance figures, refuge-space and pit-clearance figures, pendulum-impact test set-ups for doors, guide-rail force and stress formulas, and buffer-stroke rules.
It also contains Table 23 for linking requirements to verification methods, Table A.1 for electric safety devices and their minimum SIL, and Annex C’s ladder types and dimensions for pit access. For installers and assessors, this is the part of the document that turns general safety aims into testable and checkable requirements.
Relations
- Effective Date
- 18-Jan-2023
- Effective Date
- 01-Jul-2026
- Refers
EN 13411-8:2011 - Terminations for steel wire ropes - Safety - Part 8: Swage terminals and swaging - Effective Date
- 01-Jul-2026
- Effective Date
- 01-Jul-2026
- Effective Date
- 01-Jul-2026
- Effective Date
- 01-Jul-2026
- Effective Date
- 01-Jul-2026
- Effective Date
- 01-Jul-2026
- Effective Date
- 01-Jul-2026
- Effective Date
- 01-Jul-2026
- Effective Date
- 01-Jul-2026
- Effective Date
- 01-Jul-2026
- Effective Date
- 01-Jul-2026
- Effective Date
- 01-Jul-2026
- Effective Date
- 01-Jul-2026
Get Certified
Connect with accredited certification bodies for this standard

DIBt (Deutsches Institut für Bautechnik)
German Institute for Building Technology.
DIN CERTCO
DIN Group product certification.

Aboma Certification B.V.
Specialized in construction, metal, and transport sectors.
Sponsored listings
Frequently Asked Questions
EN ISO 8100-1:2026 is a standard published by the European Committee for Standardization (CEN). Its full title is "Lifts for the transport of persons and goods - Part 1: Safety rules for the construction and installation of passenger and goods passenger lifts (ISO 8100-1:2026, including corrected version 2026-05)". This standard covers: This document specifies the safety rules for lifts permanently serving buildings and constructions and intended for the transport of persons or persons and goods. It applies to traction lifts, positive drive lifts and hydraulic lifts that: serve specific levels; and have a rated speed exceeding 0,15 m/s; and have an enclosed car; and move along guide rails inclined not more than 15° to the vertical; and are indoor or weather-protected. This document also applies to the electrical equipment of these lifts including the lighting and socket outlets in the well. This document specifies safety rules related to: persons to be safeguarded: users, including passengers, maintenance and inspection personnel; persons at the landings and outside of the well, or any machinery space and pulley room, who can be affected by the lift. property to be safeguarded: loads in the car; components of the lift installation; building in which the lift is installed. This document does not specify additional requirements for: lifts serving buildings with requirements for seismic conditions; lifts serving buildings with requirements for accessibility; lifts exposed to vandalism; lifts which can be used for firefighting and evacuation purposes under firefighters control; lifts which can be used to support faster evacuation of persons with disabilities; the behaviour of the lift when the control system of the lift receives a recall signal(s) in the event of fire in a building. This document is not applicable to passenger and goods passenger lifts, which are installed before the date of its publication.
This document specifies the safety rules for lifts permanently serving buildings and constructions and intended for the transport of persons or persons and goods. It applies to traction lifts, positive drive lifts and hydraulic lifts that: serve specific levels; and have a rated speed exceeding 0,15 m/s; and have an enclosed car; and move along guide rails inclined not more than 15° to the vertical; and are indoor or weather-protected. This document also applies to the electrical equipment of these lifts including the lighting and socket outlets in the well. This document specifies safety rules related to: persons to be safeguarded: users, including passengers, maintenance and inspection personnel; persons at the landings and outside of the well, or any machinery space and pulley room, who can be affected by the lift. property to be safeguarded: loads in the car; components of the lift installation; building in which the lift is installed. This document does not specify additional requirements for: lifts serving buildings with requirements for seismic conditions; lifts serving buildings with requirements for accessibility; lifts exposed to vandalism; lifts which can be used for firefighting and evacuation purposes under firefighters control; lifts which can be used to support faster evacuation of persons with disabilities; the behaviour of the lift when the control system of the lift receives a recall signal(s) in the event of fire in a building. This document is not applicable to passenger and goods passenger lifts, which are installed before the date of its publication.
EN ISO 8100-1:2026 is classified under the following ICS (International Classification for Standards) categories: 91.140.90 - Lifts. Escalators. The ICS classification helps identify the subject area and facilitates finding related standards.
EN ISO 8100-1:2026 has the following relationships with other standards: It is inter standard links to EN 81-20:2020, EN 13501-1:2018, EN 13411-8:2011, IEC 60947-5-1:2024, IEC 60529:1989, IEC 60364-6:2016, ISO 8102-1:2020, ISO 14122-3:2016, IEC 60947-4-1:2023, ISO 6743-4:2015, IEC 61800-5-2:2016, ISO 8100-2:2026, EN 13501-6:2018+A1:2022, EN 13411-7:2021, ISO 4190-5:2006. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN ISO 8100-1:2026 is associated with the following European legislation: EU Directives/Regulations: 2014/33/EU; Standardization Mandates: M/549, M/599. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
EN ISO 8100-1:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2026
Nadomešča:
SIST EN 81-20:2020
Dvigala za prevoz oseb in blaga - 1. del: Varnostna pravila za konstruiranje in
vgradnjo dvigal (liftov) za osebna in tovorno-osebna dvigala (ISO 8100-1:2026,
vključuje popravljeno različico 2026-05)
Lifts for the transport of persons and goods - Part 1: Safety rules for the construction and
installation of passenger and goods passenger lifts (ISO 8100-1:2026, including
corrected version 2026-05)
Aufzüge für den Personen- und Gütertransport - Teil 1: Sicherheitsregeln für die
Konstruktion und den Einbau von Personen- und Lastenaufzügen (ISO 8100-1:2026,
einschließlich korrigierte Fassung 2026-05)
Ascenseurs pour le transport de personnes et d'objets - Partie 1: Règles de sécurité pour
la construction et l'installation d'ascenseurs et d'ascenseurs de charge (ISO 8100-
1:2026, y compris version corrigée 2026-05)
Ta slovenski standard je istoveten z: EN ISO 8100-1:2026
ICS:
91.140.90 Dvigala. Tekoče stopnice Lifts. Escalators
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 8100-1
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2026
EUROPÄISCHE NORM
ICS 91.140.90 Supersedes EN 81-20:2020
English Version
Lifts for the transport of persons and goods - Part 1: Safety
rules for the construction and installation of passenger
and goods passenger lifts (ISO 8100-1:2026, including
corrected version 2026-05)
Ascenseurs pour le transport de personnes et d'objets - Aufzüge für den Personen- und Gütertransport - Teil 1:
Partie 1: Règles de sécurité pour la construction et Sicherheitsregeln für die Konstruktion und den Einbau
l'installation d'ascenseurs et d'ascenseurs de charge von Personen- und Lastenaufzügen (ISO 8100-1:2026,
(ISO 8100-1:2026, y compris version corrigée 2026- einschließlich korrigierte Fassung 2026-05)
05)
This European Standard was approved by CEN on 1 March 2026.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8100-1:2026 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2014/33/EU aimed to be covered . 4
European foreword
This document (EN ISO 8100-1:2026) has been prepared by Technical Committee ISO/TC 178 "Lifts,
escalators and moving walks" in collaboration with Technical Committee CEN/TC 10 “Lifts, escalators
and moving walks” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2026, and conflicting national standards
shall be withdrawn at the latest by June 2029.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 81-20:2020.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this
document.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 8100-1:2026, including corrected version 2026-05 has been approved by CEN as
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2014/33/EU aimed to be covered
This European Standard has been prepared under a Commission’s standardization request C(2023)
3)
6588 final (‘M/599’) to provide one voluntary means of conforming to requirements of
Directive 2014/33/EU of the European Parliament and of the Council of 26 February 2014 as regards
lifts and safety components for lifts (OJ L 96, 29.3.2014).
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1.1, Table ZA.1.2 and Table
ZA.1.3 confers, within the limits of the scope of this standard, a presumption of conformity with the
corresponding essential requirements of that Directive and associated EFTA regulations.
Table ZA.1.1 — Correspondence between this European Standard and Annex I of
Directive 2014/33/EU
The relevant essential
health and safety
requirements of Clause(s)/sub-clause(s) of this EN Remarks/Notes
Annex I to
Directive 2014/33/EU
1.1 See below Table ZA.1.2 and Table ZA.1.3
1.2 first paragraph 4.2.6.4.3.2 f), 4.3.3.1, 4.3.3.2, 4.3.5.1,
4.3.5.2, 4.3.5.4, 4.3.5.5, 4.3.5.6,
4.4.1, 4.4.2.1.1, 4.4.2.1.2, 4.4.2.1.3,
4.4.2.2, 4.4.2.3.1, 4.4.3.2, 4.4.3.4
1.2 second paragraph Not covered
1.3 4.5.1, 4.5.2, 4.5.4, 4.5.5,
1.4.1 4.4.2.1.4, 4.12.1.2
1.4.2 4.6.1.1, 4.6.1.2, 4.6.2.2.1.1, 4.6.2.2.5.5,
4.6.3.1, 4.6.4.1
1.4.3 4.8.2.2.1 b), 4.6.2.2.1.6 a) 4.6.2.2.5.4 a) 4.12.1.3
2), 2),
1.4.4 4.5.3, 4.5.6, 4.5.7.2
1.5.1 4.9.1.1
1.5.2 4.2.1.1.1, 4.2.3.3 b), 4.2.5.2.1, 4.2.5.2.2,
3)
C(2023) 6588, COMMISSION IMPLEMENTING DECISION of 5.10.2023 on a standardisation request to the European
Committee for Standardization as regards lifts and safety components for lifts in support of Directive 2014/33/EU of the
European Parliament and of the Council
The relevant essential
health and safety
requirements of Clause(s)/sub-clause(s) of this EN Remarks/Notes
Annex I to
Directive 2014/33/EU
4.2.6.4.3.2 d), 4.2.6.5.1.2, 4.2.6.5.1.3 b), 4.2.6.6.1 b),
4.3.9.1.1, 4.3.9.3
1.6.1 Not covered
1.6.2 4.3.6.2.3.4 c), 4.12.1.1.1, 4.12.1.1.2
1.6.3 4.10.5.3
1.6.4 4.2.1.1.2, 4.9.2.5, 4.9.3.4,
4.10.1.1.2, 4.10.1.1.3, 4.10.1.2, 4.10.1.3,
4.10.2, 4.10.3, 4.10.4, 4.10.5,
4.10.6, 4.10.7, 4.10.8.3,
4.10.9, 4.10.10, 4.11
2.1 4.2.1.3.1 a), 4.2.3.3, 4.2.5.2, 4.2.5.5.2,
4.2.6.4.4.1 d), 4.3.1, 4.3.4, 4.3.5.2,
4.3.8, 4.3.9, 4.3.10, 4.4.8 a)
2.2 4.2.5.6, 4.2.5.7, 4.2.5.8,
4.5.3.3, 4.8.1.2, 4.9.3.2.6.2
2.3 4.3.1.1, 4.3.1.2, 4.3.3,
4.3.5.1, 4.3.5.2, 4.3.5.3, 4.3.5.4,
4.3.5.5, 4.3.5.6, 4.3.5.8,
4.3.8, 4.3.9.1, 4.3.9.3, 4.3.9.4,
4.3.10, 4.3.11, 4.12.1.4, 4.12.1.8
3.1 4.2.5.3.1 c), 4.2.6.4.3.2, 4.3.1, 4.3.9.2,
4.3.13, 4.3.14, 4.3.15.2,
4.4.3.1, 4.4.9.3
3.2 4.6.1, 4.6.2, 4.6.3.1, 4.6.3.8,
4.6.4.1, 4.6.4.6, 4.6.6, 4.6.7,
4.7
3.3 4.2.5.6.1,
4.8.1.1, 4.8.1.3, 4.8.1.4, 4.8.2.1.1.1,
4.8.2.1.2.2, 4.8.2.2.1
3.4 4.6.2.1.5, 4.6.2.2.1.6 b), 4.6.2.2.1.6 c), 4.6.2.2.3 e),
4.6.2.2.5.4 b), 4.6.2.2.5.4 c), 4.6.2.2.5.6,
The relevant essential
health and safety
requirements of Clause(s)/sub-clause(s) of this EN Remarks/Notes
Annex I to
Directive 2014/33/EU
4.6.6.5, 4.6.7.8
4.1 4.3.6.2, 4.12.1.1.4
4.2 not covered
4.3 4.2.5.5.3, 4.4.11.2, 4.4.11.3 a), 4.7.5.2
4.4 4.2.3.1, 4.2.6.2.2, 4.2.6.6.1
1st paragraph
,
4.2.6.6.2 a), 4.2.6.6.2 c), 4.3.9.3.1, 4.3.9.3.2,
4.3.9.3.7, 4.3.15.1, 4.3.15.3, 4.4.6.2,
4.9.2.3.1, 4.9.2.3.3, 4.9.2.3.4, 4.9.2.3.5,
4.9.2.3.6, 4.9.2.3.7, 4.9.2.3.9, 4.9.3.9.1.1,
4.9.3.9.1.2, 4.9.3.9.1.3, 4.9.3.9.1.4, 4.9.3.9.1.5,
4.9.3.9.2.1, 4.9.3.9.2.2, 4.9.3.9.2.3, 4.9.3.9.3,
4.10.11, 4.12.1.6, 4.12.3.2
4.5 not covered
4.6 4.9.3.11, 4.10.4.3, 4.10.4.4
4.7 4.4.9
4.8 4.4.10.1, 4.4.10.2, 4.4.10.3, 4.4.10.4 b)
4.9 4.10.11.1 a), 4.10.11.2
4.10 not covered
5.1 4.4.2.3.2 d), 4.4.2.3.2 e)
5.2 not covered
6.1 not covered
6.2 6.2, 6.3
Table ZA.1.2 — Correspondence between this European Standard and Annex I of
Directive 2006/42/EC
The relevant essential
health and safety
requirements of Clause(s)/sub-clause(s) of this EN Remarks/Notes
Annex I to
Directive 2006/42/EC
1.1.2 (a) 4, 5, 6
1.1.2 (c) 4, 5, 6
1.1.2 (e) 4, 5, 6
1.1.3 4.4.4,
4.9.3.1.4, 4.9.3.2.5.1, 4.9.3.7, 4.9.3.11
1.1.4 4.2.1.2, 4.2.6.6.3, 4.4.10,
4.10.5.1.1 a), 4.10.5.1.1 c), 4.10.5.1.1 e),
4.10.7.1, 4.10.8
1.1.5 C.4 a)
1.1.6 4.2.3.2, 4.2.6.3.2.1, 4.2.6.3.2.2, 4.2.6.4.1.1,
4.2.6.4.2, 4.4.6.1 a), 4.12.1.5.1.2, C.3,
C.4, C.5
1.2.1 4.9.2.2.2.3, 4.9.2.3.1, 4.9.2.5, 4.9.2.6,
4.9.2.7, 4.9.3.4, 4.9.3.10,
4.10.3, 4.11, 4.12, Annex A
1.2.2 4.2.1.3.1 a), 4.2.1.3.1 b),
4.4.8 a), 4.4.8 b), 4.10.1.1.2,
4.12.1.5, 4.12.1.6, 4.12.1.7, 4.12.1.8
1.2.3 4.2.6.4.4.1 g), 4.3.9.1.12 f), 4.4.6.1 b) 3), 4.4.6.2 b) 3),
4.5.3.3 a) 2), 4.5.3.3 b),
4.6.2.1.4.3, 4.6.2.2.1.6 b), 4.6.2.2.5.4 b), 4.6.5.10,
4.6.6.7, 4.6.6.2, 4.6.7.3, 4.6.7.9,
4.9.2.7.3, 4.9.3.10.3, 4.11.1.5, 4.12.1.3.2,
4.12.1.5, 4.12.1.6, 4.12.1.11.2, 4.12.2.3.2
1.2.4.1 4.2.1.3.1 d), 4.12.1.11.1, 4.12.1.11.2
1.2.4.4 4.4.6.2 b) 3), 4.12.1.11.1
1.2.5 4.12.1.5, 4.12.1.6, 4.12.1.8
1.2.6 4.6.2.1.4.3, 4.6.2.2.5.6, 4.6.5.10, 4.6.6.7,
4.6.7.9, 4.9.2.2.2.3 g), 4.9.2.2.2.8, 4.11.1.1,
The relevant essential
health and safety
requirements of Clause(s)/sub-clause(s) of this EN Remarks/Notes
Annex I to
Directive 2006/42/EC
4.11.2.4.2.2, 4.11.2.4.3.2, 4.12.1.3.2, 4.12.2.3.2
1.3.1 4.2.1.5, 4.9.3.2.6.3
1.3.2 4.3.3.3, 4.3.5.2, 4.4.3.2, 4.4.11.2,
4.5.2, 4.5.6.3, 4.5.8 a), 4.6.2.2.1.3,
4.6.3.3, 4.6.4.3, 4.7, 4.9.3.2.1,
4.9.3.2.2, 4.9.3.2.3, 4.9.3.2.6.1, 4.9.3.2.6.4,
4.9.3.2.6.5, 4.9.3.2.6.6, 4.9.3.3.1, 4.9.3.5.3,
6.2.4
1.3.3 4.2.2.2 f), 4.2.2.2 g), 4.2.5.4, 4.2.6.3.3,
4.2.6.7.2, 4.4.7.2 a), 4.4.11.3
1.3.4 4.2.5.3.2 c), 4.2.5.3.2 d), 4.3.6.1, 4.3.6.2.2.1 f),
4.3.6.2.2.1 g), 4.3.6.2.2.1 i), 4.3.6.2.2.1 j), 4.3.6.2.2.1 k),
4.4.5.1
1.3.7 4.2.5.5, 4.4.7.4 d),
4.5.6.2 e), 4.5.7, 4.6.2.1.6.3, 4.6.2.2.3 g),
4.9.1.2, 4.9.2.3.4 a) 1), 4.9.2.3.4 a) 3), 4.9.3.2.6.6 b)
1.3.8.1 4.2.5.5, 4.5.7.1, 4.9.1.2
1.3.9 4.2.6.4.3.1, 4.2.6.4.4.1
1.4.1 4.1.2, 4.2.3.4, 4.2.5.5.1, 4.2.5.5.2,
4.2.6.4.3.2 d), 4.2.6.4.3.2 e), 4.2.6.4.3.2 f), 4.3.9.1.8,
4.4.5, 4.4.6.1 b), 4.4.7.4, 4.5.7
1.4.2.1 4.1.2, 4.3.9.1.9 4.5.7
1.4.2.2 4.2.3.3 b), 4.2.3.3 d), 4.2.6.4.3.2 d), 4.2.6.4.3.2 e),
4.4.6.1 b) 3), 4.4.6.2 b) 3)
1.5.1 4.10.1.1.4, 4.10.1.2, 4.10.1.3,
4.10.2, 4.10.3, 4.10.4, 4.10.5,
4.10.6, 4.10.9, 4.10.10
1.5.3 4.9.3.1
1.5.4 4.3.5.2, 4.6.2.2.1.1 c), 4.9.2.3.8, 4.10.6.4
1.5.5 4.10.1.1.4
1.5.6 4.9.3.11, 4.9.2.2.2.6, 4.10.4.1, 4.10.4.2
The relevant essential
health and safety
requirements of Clause(s)/sub-clause(s) of this EN Remarks/Notes
Annex I to
Directive 2006/42/EC
1.5.7 Not covered
1.5.8 Not covered
1.5.11 Not covered
1.5.14 4.2.1.4, 4.2.3.3 c), 4.2.6.4.3.1 c), 4.2.6.4.4.2,
4.3.9.3.5, 4.12.1.11.3, 4.12.3.1
1.5.15 4.2.2.2 e), 4.2.2.2 k), 4.2.6.4.5.3 b), 4.2.6.4.5.3 d),
4.3.4.3, 4.4.7.1 b), 4.4.7.2 b), 4.4.7.2 c),
4.4.7.2 d), 4.4.7.3, 4.4.7.4, 4.12.1.1.3,
C.3.3 d)
1.6.1 4.6.3.6, 4.6.3.7, 4.6.4.5, 4.12.1.5,
4.12.1.7, 4.12.1.8, 4.12.1.11.1, 6.2.4
1.6.2 4.2.2.1, 4.2.3.2, 4.2.3.3, 4.2.3.4,
4.2.6.3.2, 4.2.6.4.1.1, 4.2.6.4.2, 4.2.6.4.3.1 c),
4.2.6.4.3.2, 4.2.6.4.4.2, 4.2.6.4.5, 4.2.6.4.6,
4.2.6.6.4, 4.2.6.7.1, 4.6.3.2, 4.6.4.2,
C.1, C.2
1.6.3 4.10.1.2.4, 4.10.5, 4.10.8.1
1.7.1 4.1.3, 4.2.2.2 j), 4.2.5.7.1, 4.2.5.8.1,
4.2.6.4.5.7, 4.3.7, 4.4.2.2.1 g), 4.9.2.3.2,
4.9.2.3.8, 4.9.3.3.3.3, 4.9.3.7, 4.10.1.2.5,
4.10.5.6, 4.12.1.5.1.2 b 4.12.1.5.4, 4.12.1.8.4
),
1.7.2 4.2.2.2 j), 4.2.4, 4.2.6.2, 4.2.6.4.5.7,
4.2.5.7.1, 4.2.5.8.1, 4.2.6.4.1.2, 4.3.6.2.2.1 b)
3),
4.3.6.2.3.1 d), 4.3.9.3.9, 4.9.2.3.2, 4.10.1.2.5,
4.10.5.6, 4.12.1.1.5, 4.12.1.2.3 a), 4.12.1.2.3 b),
4.12.1.5.3, 4.12.1.8.3 c), 4.12.1.10 b), 4.12.1.10 c)
1.7.3 4.2.6.4.5.7, 4.3.9.1.11, 4.4.2.2.1 g), 4.4.2.3.2 a),
4.4.2.3.2 b), 4.4.2.3.2 c), 4.4.2.3.2 e), 4.4.2.3.2 f),
4.4.2.3.3, 4.6.2.1.1.3, 4.6.2.2.1.8,
The relevant essential
health and safety
requirements of Clause(s)/sub-clause(s) of this EN Remarks/Notes
Annex I to
Directive 2006/42/EC
4.6.3.9, 4.6.4.7, 4.6.6.12, 4.6.7.14,
4.8.1.8, 4.9.3.3.3.3, 4.9.3.9.1.6, 4.9.3.9.2.4,
4.11.2.3.5
4.1.2.3 4.5.3, 4.6.3.5, 4.6.4.4, 4.7.2.3.1,
4.9.2.2.2.1, 4.9.3.3.2, 4.9.3.3.3.1, 4.9.3.3.3.2,
5.2.4, 5.2.5, 5.2.7, 5.2.9,
5.2.10,
4.1.2.4 4.5.1, 4.5.2, 4.5.4, 4.5.6
4.1.2.8.2 4.4.2.2.1 d), 4.12.1.1.3, 4.12.1.2.1, 4.12.1.12.4
4.2.1 4.9.2.3.1, 4.9.3.9.1.3, 4.12.1.5.2.1 f), 4.12.1.5.2.3,
4.12.1.6.1.2 b 4.12.1.6.2.1 c)
),
4.3.1 4.5.9
6.3.1 4.2.6.4.4.1 a), 4.5.3.2, 4.6.2.1.2.1, 4.6.2.1.3,
4.6.3.1, 4.6.6.3, 4.6.7.6, 4.8.1.5,
4.8.1.7, 4.8.2.1.1, 4.8.2.1.2.1 a), 4.8.2.1.2.1 b),
4.8.2.1.2.1 e), 4.8.2.2.2 a), 4.8.2.2.2 b),
4.9.2.2.2.1 4.9.3.2.3.2, 4.9.3.2.4.2
st
1 paragraph,
6.3.2 4.2.6.4.3.2, 4.4.3.2.1, 4.4.6, 4.4.7.2 b),
4.4.7.2 c), 4.4.7.3, 4.6.3.4
Table ZA.1.3 — Correspondence between this European Standard and Annex III of
Regulation (EU) 2023/1230
The relevant essential
health and safety
requirements of Annex Clause(s)/sub-clause(s) of this EN Remarks/Notes
III to Regulation (EU)
2023/1230
1.1.2 (a) 4, 5, 6
1.1.2 (c) 4, 5, 6
1.1.2 (e) 4, 5, 6
1.1.3 4.4.4,
4.9.3.1.4, 4.9.3.2.5.1, 4.9.3.7, 4.9.3.11
1.1.4 4.2.1.2, 4.2.1.3.1 a), 4.2.6.6.3, 4.4.10,
4.10.5.1.1 a), 4.10.5.1.1 c), 4.10.5.1.1 e),
4.10.7.1, 4.10.8
1.1.5 C.4 a)
1.1.6 4.2.3.2, 4.2.6.3.2.1, 4.2.6.3.2.2, 4.2.6.4.1.1,
4.2.6.4.2, 4.4.6.1 a), 4.12.1.5.1.2, C.3,
C.4, C.5
1.1.9 4.10.1.1.5, 4.10.1.1.6, 4.12.4, 6.2.4 k) 7),
6.2.4 v)
1.2.1 4.9.2.2.2.3, 4.9.2.3.1, 4.9.2.5, 4.9.2.6,
4.9.2.7, 4.9.3.4, 4.9.3.10,
4.10.1.1.5 4.10.1.1.6,
4.10.3, 4.11, 4.12, Annex A
1.2.2 4.2.1.3.1 a), 4.2.1.3.1 b),
4.4.8 a), 4.4.8 b), 4.10.1.1.2,
4.12.1.5, 4.12.1.6, 4.12.1.7, 4.12.1.8
1.2.3 4.2.6.4.4.1 g), 4.3.9.1.12 f), 4.4.6.1 b) 3), 4.4.6.2 b) 3),
4.5.3.3 a) 2), 4.5.3.3 b),
4.6.2.1.4.3, 4.6.2.2.1.6 b), 4.6.2.2.5.4 b), 4.6.5.10,
4.6.6.7, 4.6.6.2, 4.6.7.3, 4.6.7.9,
4.9.2.7.3, 4.9.3.10.3, 4.11.1.5, 4.12.1.3.2,
4.12.1.5, 4.12.1.6, 4.12.1.11.2, 4.12.2.3.2
1.2.4.1 4.2.1.3.1 d), 4.12.1.11.1, 4.12.1.11.2
1.2.4.4 4.4.6.2 b) 3), 4.12.1.11.1
The relevant essential
health and safety
requirements of Annex Clause(s)/sub-clause(s) of this EN Remarks/Notes
III to Regulation (EU)
2023/1230
1.2.5 4.12.1.5, 4.12.1.6, 4.12.1.8
1.2.6 4.6.2.1.4.3, 4.6.2.2.5.6, 4.6.5.10, 4.6.6.7,
4.6.7.9, 4.9.2.2.2.3 g), 4.9.2.2.2.8, 4.11.1.1,
4.11.2.4.2.2, 4.11.2.4.3.2, 4.12.1.3.2, 4.12.2.3.2
1.3.1 4.2.1.5, 4.9.3.2.6.3
1.3.2 4.3.3.3, 4.3.5.2, 4.4.3.2, 4.4.11.2,
4.5.2, 4.5.6.3, 4.5.8 a), 4.6.2.2.1.3,
4.6.3.3, 4.6.4.3, 4.7, 4.9.3.2.1,
4.9.3.2.2, 4.9.3.2.3, 4.9.3.2.6.1, 4.9.3.2.6.4,
4.9.3.2.6.5, 4.9.3.2.6.6, 4.9.3.3.1, 4.9.3.5.3,
6.2.4
1.3.3 4.2.2.2 f), 4.2.2.2 g), 4.2.5.4, 4.2.6.3.3,
4.2.6.7.2, 4.4.7.2 a), 4.4.11.3
1.3.4 4.2.5.3.2 c), 4.2.5.3.2 d), 4.3.6.1, 4.3.6.2.2.1 f),
4.3.6.2.2.1 g), 4.3.6.2.2.1 i), 4.3.6.2.2.1 j), 4.3.6.2.2.1 k),
4.4.5.1
1.3.7 4.2.5.5, 4.4.7.4 d),
4.5.6.2 e), 4.5.7, 4.6.2.1.6.3, 4.6.2.2.3 g),
4.9.1.2, 4.9.2.3.4 a) 1), 4.9.2.3.4 a) 3), 4.9.3.2.6.6 b)
1.3.8.1 4.2.5.5, 4.5.7.1, 4.9.1.2
1.3.9 4.2.6.4.3.1, 4.2.6.4.4.1
1.4.1 4.1.2, 4.2.3.4, 4.2.5.5.1, 4.2.5.5.2,
4.2.6.4.3.2 d), 4.2.6.4.3.2 e), 4.2.6.4.3.2 f), 4.3.9.1.8,
4.4.5, 4.4.6.1 b), 4.4.7.4, 4.5.7
1.4.2.1 4.1.2, 4.3.9.1.9 4.5.7
1.4.2.2 4.2.3.3 b), 4.2.3.3 d), 4.2.6.4.3.2 d), 4.2.6.4.3.2 e),
4.4.6.1 b) 3), 4.4.6.2 b) 3),
1.5.1 4.10.1.1.4, 4.10.1.2, 4.10.1.3,
4.10.2, 4.10.3, 4.10.4, 4.10.5,
4.10.6, 4.10.9, 4.10.10
1.5.3 4.9.3.1
The relevant essential
health and safety
requirements of Annex Clause(s)/sub-clause(s) of this EN Remarks/Notes
III to Regulation (EU)
2023/1230
1.5.4 4.3.5.2, 4.6.2.2.1.1 c), 4.9.2.3.8, 4.10.6.4
1.5.5 4.10.1.1.4
1.5.6 4.9.3.11, 4.9.2.2.2.6, 4.10.4.1, 4.10.4.2
1.5.7 Not covered
1.5.8 Not covered
1.5.11 Not covered
1.5.14 4.2.1.4, 4.2.3.3 c), 4.2.6.4.3.1 c), 4.2.6.4.4.2,
4.3.9.3.5, 4.12.1.11.3, 4.12.3.1
1.5.15 4.2.2.2 e), 4.2.2.2 k), 4.2.6.4.5.3 b), 4.2.6.4.5.3 d),
4.3.4.3, 4.4.7.1 b), 4.4.7.2 b), 4.4.7.2 c),
4.4.7.2 d), 4.4.7.3, 4.4.7.4, 4.12.1.1.3,
C.3.3 d)
1.6.1 4.6.3.6, 4.6.3.7, 4.6.4.5, 4.12.1.5,
4.12.1.7, 4.12.1.8, 4.12.1.11.1, 6.2.4
1.6.2 4.2.2.1, 4.2.3.2, 4.2.3.3, 4.2.3.4,
4.2.6.3.2, 4.2.6.4.1.1, 4.2.6.4.2, 4.2.6.4.3.1 c),
4.2.6.4.3.2, 4.2.6.4.4.2, 4.2.6.4.5, 4.2.6.4.6,
4.2.6.6.4, 4.2.6.7.1, 4.6.3.2, 4.6.4.2,
C.1, C.2
1.6.3 4.10.1.2.4, 4.10.5, 4.10.8.1
1.7.1 4.1.3, 4.2.2.2 j), 4.2.5.7.1, 4.2.5.8.1,
4.2.6.4.5.7, 4.3.7, 4.4.2.2.1 g), 4.9.2.3.2,
4.9.2.3.8, 4.9.3.3.3.3, 4.9.3.7, 4.10.1.2.5,
4.10.5.6, 4.12.1.5.1.2 b 4.12.1.5.4, 4.12.1.8.4
),
1.7.2 4.2.2.2 j), 4.2.4, 4.2.6.2, 4.2.6.4.5.7,
4.2.5.7.1, 4.2.5.8.1, 4.2.6.4.1.2, 4.3.6.2.2.1 b)
3),
4.3.6.2.3.1 d), 4.3.9.3.9, 4.9.2.3.2, 4.10.1.2.5,
4.10.5.6, 4.12.1.1.5, 4.12.1.2.3 a), 4.12.1.2.3 b),
4.12.1.5.3, 4.12.1.8.3 c), 4.12.1.10 b), 4.12.1.10 c)
The relevant essential
health and safety
requirements of Annex Clause(s)/sub-clause(s) of this EN Remarks/Notes
III to Regulation (EU)
2023/1230
1.7.3 4.2.6.4.5.7, 4.3.9.1.11, 4.4.2.2.1 g), 4.4.2.3.2 a),
4.4.2.3.2 b), 4.4.2.3.2 c), 4.4.2.3.2 e), 4.4.2.3.2 f),
4.4.2.3.3, 4.6.2.1.1.3, 4.6.2.2.1.8,
4.6.3.9, 4.6.4.7, 4.6.6.12, 4.6.7.14,
4.8.1.8, 4.9.3.3.3.3, 4.9.3.9.1.6, 4.9.3.9.2.4,
4.11.2.3.5
4.1.2.3 4.5.3, 4.6.3.5, 4.6.4.4, 4.7.2.3.1,
4.9.2.2.2.1, 4.9.3.3.2, 4.9.3.3.3.1, 4.9.3.3.3.2,
5.2.4, 5.2.5, 5.2.7, 5.2.9,
5.2.10,
4.1.2.4 4.5.1, 4.5.2, 4.5.4, 4.5.6
4.1.2.8.2 4.4.2.2.1 d), 4.12.1.1.3, 4.12.1.2.1, 4.12.1.12.4
4.2.1 4.9.2.3.1, 4.9.3.9.1.3, 4.12.1.5.2.1 f), 4.12.1.5.2.3,
4.12.1.6.1.2 b 4.12.1.6.2.1 c)
),
4.3.1 4.5.9
6.3.1 4.2.6.4.4.1 a), 4.5.3.2, 4.6.2.1.2.1, 4.6.2.1.3,
4.6.3.1, 4.6.6.3, 4.6.7.6, 4.8.1.5,
4.8.2.1.1, 4.8.2.1.2.1 a), 4.8.2.1.2.1 b),
4.8.2.1.2.1 e), 4.8.2.2.2 a), 4.8.2.2.2 b),
4.9.2.2.2.1 4.9.3.2.3.2, 4.9.3.2.4.2
st
1 paragraph,
6.3.2 4.2.6.4.3.2, 4.4.3.2.1, 4.4.6, 4.4.7.2 b),
4.4.7.2 c), 4.4.7.3, 4.6.3.4
WARNING 1 Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
International
Standard
ISO 8100-1
Second edition
Lifts for the transport of persons
2026-03
and goods —
Corrected version
Part 1:
2026-05
Safety rules for the construction
and installation of passenger and
goods passenger lifts
Ascenseurs pour le transport de personnes et d'objets —
Partie 1: Règles de sécurité pour la construction et l'installation
d'ascenseurs et d'ascenseurs de charge
Reference number
ISO 8100-1:2026(en) © ISO 2026
ISO 8100-1:2026(en)
© ISO 2026
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 8100-1:2026(en)
Contents Page
Foreword .vi
Introduction .viii
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 4
4 Safety requirements and/or protective measures . 9
4.1 General .9
4.2 Well, machinery spaces and pulley rooms .10
4.2.1 General provisions .10
4.2.2 Access to the pit . 13
4.2.3 Access doors, emergency doors, access trap doors and inspection doors .16
4.2.4 Notices .17
4.2.5 Well .17
4.2.6 Machinery spaces and pulley rooms . 30
4.3 Landing and car doors . 36
4.3.1 General provisions . 36
4.3.2 Height and width of entrances .37
4.3.3 Sills, guides, door suspension .37
4.3.4 Horizontal door clearances . 38
4.3.5 Strength of landing and car doors .42
4.3.6 Protection in relation to door operation . 48
4.3.7 “Car here” indication .57
4.3.8 Locking and closed landing door check . 58
4.3.9 Locking and emergency unlocking of landing and car doors . 58
4.3.10 Requirements common to devices for proving the locked condition and the
closed condition of the landing door .62
4.3.11 Sliding landing doors with multiple, mechanically linked panels .62
4.3.12 Closing of automatically operated landing doors . 63
4.3.13 Electric safety device for proving the car door closed . 63
4.3.14 Sliding or folding car door with multiple, mechanically linked panels . 63
4.3.15 Opening the car door . 64
4.4 Car, counterweight and balancing weight . 64
4.4.1 Height of car . . . 64
4.4.2 Available car area, rated load, number of passengers. 64
4.4.3 Walls, floor and roof of the car .70
4.4.4 Car door(s), floor, walls, ceiling and decorative materials . 72
4.4.5 Apron . 72
4.4.6 Emergency trap doors and emergency doors . 73
4.4.7 Car roof .74
4.4.8 Equipment on top of the car . 78
4.4.9 Ventilation . 78
4.4.10 Lighting . 78
4.4.11 Counterweight and balancing weight . 79
4.5 Suspension means, compensation means and related protection means . 79
4.5.1 Suspension means and related sheaves/drums/sprockets . 79
4.5.2 Minimum diameter ratio, safety factor, fatigue lifetime and suspension means
terminations . 82
4.5.3 Suspension means traction/transmission . 90
4.5.4 Winding up of ropes for positive drive lifts . 90
4.5.5 Distribution of load between the suspension means.91
4.5.6 Compensation means .91
4.5.7 Protection for sheaves, pulleys and sprockets . 92
4.5.8 Traction sheaves, pulleys and sprockets . 95
4.5.9 Marking of suspension means and compensation means . 95
iii
ISO 8100-1:2026(en)
4.6 Precautions against free fall, excessive speed, unintended car movement and creeping
of the car . . 96
4.6.1 Application of protections means . 96
4.6.2 Safety gear and its tripping means . 97
4.6.3 Rupture valve . 105
4.6.4 Restrictors . 106
4.6.5 Pawl device . 107
4.6.6 Ascending car overspeed protection means . 108
4.6.7 Protection against unintended car movement .110
4.7 Guide rails . 112
4.7.1 Guiding of the car, counterweight or balancing weight . 112
4.7.2 Forces and load cases . 113
4.7.3 Combination of masses and forces .116
4.7.4 Impact factors .116
4.7.5 Permissible stresses and deflections .117
4.8 Buffers . 118
4.8.1 General provisions . 118
4.8.2 Stroke of buffers .119
4.9 Lift machinery and associated equipment. 120
4.9.1 General provision . 120
4.9.2 Lift machine for traction lifts and positive drive lifts . 120
4.9.3 Lift machine for hydraulic lifts . 126
4.10 Electric installations and appliances .134
4.10.1 General provisions .134
4.10.2 Incoming supply conductor terminations . . 137
4.10.3 Contactors, contactor relays, components of safety circuits . 137
4.10.4 Protection of electrical equipment . 138
4.10.5 Main switch, supply disconnecting devices and isolating devices .138
4.10.6 Electric wiring . 140
4.10.7 Lighting and socket outlets .141
4.10.8 Control of the supply for lighting and socket outlets .141
4.10.9 Protective earthing .142
4.10.10 Identification of electrical components .142
4.10.11 Emergency supply .142
4.11 Protection against electric faults; failure analysis; electric safety devices .142
4.11.1 Protection against electric faults; failure analysis .142
4.11.2 Electric safety devices .143
4.12 Electrical Controls . 149
4.12.1 Control of lift operations . 149
4.12.2 Final limit switches .158
4.12.3 Alert initiation and intercom system . 159
4.12.4 Identification of the software . 159
5 Verification of the safety requirements and/or protective measures .159
5.1 Verification methods . 159
5.2 Specific examinations and tests on installed lift . 163
5.2.1 General . 163
5.2.2 Braking system (4.9.2.2) . 163
5.2.3 Electric installation . 164
5.2.4 Checking of the traction (4.5.3) . 164
5.2.5 Car safety gear (4.6.2). 165
5.2.6 Counterweight or balancing weight safety gear (4.6.2) . 165
5.2.7 Pawl device (4.6.5) . . 165
5.2.8 Buffers (4.8) . 166
5.2.9 Rupture valve (4.6.3) . 166
5.2.10 Restrictor/one-way restrictor (4.6.4) . 166
5.2.11 Pressure test .167
5.2.12 Ascending car overspeed protection means (4.6.6) .167
5.2.13 Stopping of the car at landings and levelling accuracy (4.12.1.1.3) .167
iv
ISO 8100-1:2026(en)
5.2.14 Protection against unintended car movement (4.6.7) .167
5.2.15 Protection against falling/shearing (4.3.9.3.4) .167
5.2.16 Balancing of vertically sliding door (4.3.3.3.5) .167
5.2.17 Counterweight balance (4.5.3) .167
5.2.18 Balancing weight balance (4.5.3) . 168
6 Information for use .168
6.1 General .
...



