ASTM D7125-23

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D7125 − 22 D7125 − 23
Standard Specification for
Cumene (Isopropylbenzene) Manufactured Via a Zeolite
Process
This standard is issued under the fixed designation D7125; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers cumene (isopropylbenzene) manufactured using a zeolite catalyst process.
1.2 The following applies to all specified limits in this specification: for purposes of determining conformance with this
specification, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used
in expressing the specification limit, in accordance with the rounding-off method of Practice E29.
1.3 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this
standard.
1.4 Consult current OSHA Regulations and Supplier’s Safety Data Sheets, and local regulations for all materials used in this
specification.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2.1 ASTM Standards:
D1492 Test Method for Bromine Index of Aromatic Hydrocarbons by Coulometric Titration
D3160 Test Method for Phenol Content of Cumene (Isopropylbenzene) or AMS (α–Methylstyrene)
D3437 Practice for Sampling and Handling Liquid Cyclic Products
D3760 Test Method for Analysis of Isopropylbenzene (Cumene) by Gas Chromatography (Withdrawn 2022)
D5386 Test Method for Color of Liquids Using Tristimulus Colorimetry
D5776 Test Method for Bromine Index of Aromatic Hydrocarbons by Electrometric Titration
D7057 Test Method for Analysis of Isopropylbenzene (Cumene) by Gas Chromatography (External Standard)
D7183 Test Method for Determination of Total Sulfur in Aromatic Hydrocarbons and Related Chemicals by Ultraviolet
Fluorescence
D7359 Test Method for Total Fluorine, Chlorine and Sulfur in Aromatic Hydrocarbons and Their Mixtures by Oxidative
Pyrohydrolytic Combustion followed by Ion Chromatography Detection (Combustion Ion Chromatography-CIC)
This specification is under the jurisdiction of Committee D16 on Aromatic, Industrial, Specialty and Related Chemicals and is the direct responsibility of Sub committee
D16.07 on Styrene, Ethylbenzene and C9 and C10 Aromatic Hydrocarbons.
Current edition approved Sept. 1, 2022April 1, 2023. Published September 2022April 2023. Originally approved in 2007. Last previous edition approved in 20172022 as
D7125 – 17.D7125 – 22. DOI: 10.1520/D7125-22.10.1520/D7125-23.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
D7125 − 23
D8005 Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E298 Test Methods for Assay of Organic Peroxides
E299 Test Method for Trace Amounts of Peroxides In Organic Solvents
E2680 Test Method for Appearance of Clear, Transparent Liquids (Visual Inspection Procedure)
2.2 Other Documents:
OSHA Regulations, 29 CFR paragraphs 1910.1000 and 1910.1200
3. Properties
3.1 Cumene (isopropylbenzene) manufactured via a catalytic zeolite process shall conform to the following requirements:
Available from Superintendent of Documents, U.S. Government Printing Office, 732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401.
D7125 − 23
ASTM Test
Property Specifications
A
Method
Purity, mass %, min 99.93 D3760 or D7057
Purity,
...