iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D5624-13

(Practice)

Standard Practice for Determining the Transverse-Aggregate Spread Rate for Surface Treatment Applications (Withdrawn 2022)

Standard Practice for Determining the Transverse-Aggregate Spread Rate for Surface Treatment Applications (Withdrawn 2022)

SIGNIFICANCE AND USE
4.1 This practice can be used to calibrate aggregate spreaders and verify the uniformity of distribution transversely prior to construction of the surface treatment by determining the average quantity of aggregate spread per unit area.  
4.2 This practice can be useful for quality control during construction to monitor the spread rate.  
4.3 The samples obtained during construction can also be used for the determination of moisture content and grading when such information is required.
SCOPE
1.1 This practice details the procedure for determining the aggregate spread rates in approximately 0.33-m transverse increments.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This practice detailed the procedure for determining the aggregate spread rates in approximately 0.33-m transverse increments.
Formerly under the jurisdiction of Committee D04 on Road and Paving Materials, this practice was withdrawn in March 2022 in accordance with section 10.6.3 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.

General Information

Status
Withdrawn
Publication Date
14-Dec-2013
Withdrawal Date
20-Mar-2022
ICS
91.100.50 - Binders. Sealing materials
Technical Committee
D04 - Road and Paving Materials
Drafting Committee
D04.24 - Asphalt Surface Treatments
Current Stage
Ref Project

Buy Standard

ASTM D5624-13 - Standard Practice for Determining the Transverse-Aggregate Spread Rate for Surface Treatment Applications (Withdrawn 2022)ASTM D5624-13 - Standard Practice for Determining the Transverse-Aggregate Spread Rate for Surface Treatment Applications (Withdrawn 2022)
PreviousNext
Standard
ASTM D5624-13 - Standard Practice for Determining the Transverse-Aggregate Spread Rate for Surface Treatment Applications (Withdrawn 2022)
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D5624 − 13
Standard Practice for
Determining the Transverse-Aggregate Spread Rate for
1
Surface Treatment Applications
This standard is issued under the fixed designation D5624; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 4. Significance and Use
1.1 This practice details the procedure for determining the 4.1 This practice can be used to calibrate aggregate spread-
aggregate spread rates in approximately 0.33-m transverse ers and verify the uniformity of distribution transversely prior
increments. to construction of the surface treatment by determining the
average quantity of aggregate spread per unit area.
1.2 The values stated in SI units are to be regarded as
standard. No other units of measurement are included in this 4.2 This practice can be useful for quality control during
standard. construction to monitor the spread rate.
1.3 This standard does not purport to address all of the
4.3 The samples obtained during construction can also be
safety concerns, if any, associated with its use. It is the
used for the determination of moisture content and grading
responsibility of the user of this standard to establish appro-
when such information is required.
priate safety and health practices and determine the applica-
5. Apparatus
bility of regulatory limitations prior to use.
5.1 Balance—A balance (or scale) of sufficient capacity to
2. Referenced Documents
handle the mass of the aggregate shall be provided. This
2
2.1 ASTM Standards: balance (or scale) shall be readable and accurate to1gif only
the transverse spread rate is being determined; an accuracy of
C136 Test Method for Sieve Analysis of Fine and Coarse
0.1 g is needed if moisture content is being determined. All
Aggregates
balances, or scales, shall meet the requirement set forth in
C566 Test Method forTotal Evaporable Moisture Content of
Method E898 for top loading, direct-reading laboratory scales
Aggregate by Drying
and balances.
E898 Test Method of Testing Top-Loading, Direct-Reading
Laboratory Scales and Balances
5.2 Containers—Containers, sufficient in number for the
number of samples to be taken, and of a sufficient size to hold
3. Summary of Practice
the contents of one mat. If moisture content is to be
3.1 The transverse-aggregate spread rate is determined by
determined, then the container shall be sealable.
the use of a series of pads laid side by side width-wise across
5.3 Mats—Individual flat mats with a known surface area.
the pavement. The aggregate spreader is then allowed to
The material should be able to stay in place as the aggregate
proceed across the mats with the gates open allowing the
spreader moves over the mats in the wheel paths. The material
aggregate to drop onto the mats. Aggregate collected on each
should also have sufficient texture so the aggregate does not
of the mats is removed and weighed. The transverse-aggregate
roll appreciably when dropped from the aggregate spreader
distribution then is calculated, and the aggregate spreader
(Note 1).
adjusted if desired. Moisture content and aggregate gradation
NOTE 1—Rubber floor mats and roofing felt materials of known
can be determined from the collected material.
dimensions have been used successfully.
5.4 Oven—The oven shall be a forced air type oven capable
1
This practice is under the jurisdiction of ASTM Committee D04 on Road and
of maintaining a uniform temperature of 110 6 5°C.
Paving Materials and is the direct responsibility of Subcommittee D04.24 on
Bituminous Surface Treatments.
PROCEDURES
Current edition approved Dec. 15, 2013. Published January 2014. Originally
approved in 1994. Last previous edition approved in 2007 as D5624 – 02 (2007).
6. Determination of Transverse Spread Rate
DOI: 10.1520/D5624-13.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
6.1 Place the mats side by side width-wise on the pavement
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
with the grooves perpendicular to the centerline (Fig. 1). This
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. practicecanbeusedtoevaluatetheuniformityoftheaggregate
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D5624 − 13
FIG. 1 Layout of Mats
spread rate across the entire width of spreader box, or limited 7.2 Determine the moisture content of the aggregate in
to key areas of interest such as within the wheel paths. accordance with Test Method C566.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D8125-18(2023)(Specification)
Standard Specification for Re-Refined Engine Oil Bottoms (REOB)/Vacuum Tower Asphalt Extender (VTAE)

ABSTRACT
This specification establishes the material, manufacturing, and physical requirements for re-refined engine oil bottoms, also known as vacuum tower asphalt extender, that may be used in formulating asphalt for pavement construction and roofing. "Re-refined engine oil bottoms" (REOB) is the commonly used term used by many state highway agencies and FHWA, while "vacuum tower asphalt extender" (VTAE) is preferred by manufacturers. REOB/VTAE may be obtained by processing used engine oil using atmospheric distillation followed by vacuum distillation to produce a vacuum residuum meeting the requirements outlined in this specification. The REOB/VTAE shall be homogenous, free from water, and not foam when heated to 232°C (450°F).
SCOPE
1.1 This specification covers re-refined engine oil bottoms, also known as vacuum tower asphalt extender, that may be used in formulating asphalt for pavement construction and roofing. This specification has been developed specifically for these two categories of product and is not intended for other uses. Table 1 is to be used for pavement construction and Table 2 for roofing. “Re-refined engine oil bottoms” (REOB) is the prevailing name used by many state highway agencies and FHWA, while “vacuum tower asphalt extender” (VTAE) is the preferred name used by the manufacturers of the product. Since each name provides an important descriptor of production elements (“re-refined” and “vacuum tower”) for the specific product this specification addresses, this specification uses the term “REOB/VTAE.”  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D8140-18(2023)(Guide)
Standard Guide for the Use of Foundry Sand in Asphalt Mixtures

SCOPE
1.1 This guide covers the physical and chemical requirements of virgin or recovered foundry sand for use as a fine aggregate in asphalt mixtures.  
1.2 This guide is for use by contractors, foundry sand suppliers, or other purchasers as part of the purchase document describing the material to be furnished. Those responsible for selecting the proportions for the asphalt mixture should have the responsibility of determining the proportions of foundry sand as a fine aggregate.  
1.3 The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.  
1.4 The text of this standard references notes and footnotes which provide explanatory information. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3549/D3549M-18(2023)(Test Method)
Standard Test Method for Thickness or Height of Compacted Asphalt Mixture Specimens

SIGNIFICANCE AND USE
4.1 The thickness of a compacted asphalt mixture is often used as a construction check to ensure that the proper quantity of materials has been placed on a project, and to correct strength measurement on constant diameter specimens with varying heights.
Note 1: The text of this test method references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the test method.
Note 2: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers determination of the thickness (or height) of compacted asphalt mixture specimens.  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.2.1 Section 7.4 specifies SI units because they are the units used in the equations for Test Methods D1188/D1188M and D2726/D2726M. Performing calculations without first converting any measurements made in inch-pound units to SI units in 7.4 will result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D8138-23(Specification)
Standard Specification for Preformed Silicone Joint Sealing System for Bridges

ABSTRACT
This specification covers the material, manufacturing, and physical requirements for preformed silicone joint seals used in bridges. The seal consists of a silicone rubber gland preformed to a continuous length and is designed to prevent any tension from occurring in the seal or bonding point during normal movement. The seal is installed by bonding it to the joint header with a silicone-based adhesive, sealing the joint to prevent liquid intrusion. Physical requirements for the preformed silicone joint seal gland cover resistance to accelerated weathering, tensile strength, elongation at break, hardness, tear strength, compression set, and heat-aged properties, whereas physical requirements for the silicone-based adhesive cover tensile strength, elongation at break, sag/flow, tack-free time, resistance to UV, and cure through to 1/4-in. thickness.
SCOPE
1.1 This specification covers the material requirements for preformed silicone joint seals for bridges. The seal consists of a silicone rubber gland preformed to a continuous length. Its design shall prevent any tension from occurring in the seal or bonding point during normal movement. The seal is installed by bonding it to the joint header with a silicone-based adhesive and is designed to seal the joint, preventing liquid intrusion.  
1.2 The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D8188-23(Test Method)
Standard Test Method for Determination of Density and Relative Density of Asphalt, Semi-Solid Bituminous Materials, and Soft-Tar Pitch by Use of a Digital Density Meter (U-Tube)

SIGNIFICANCE AND USE
5.1 Values of density are used for converting volumes to units of mass and for correcting measured volumes at the measured temperature to a standard temperature using Practice D4311/D4311M.
Note 2: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers the determination of the relative density and density of semi-solid asphalt materials, asphalt binders, asphalt cements, and soft-tar pitches by use of a digital density meter (U-tube).
Note 1: Alternate methods for determining the density of semi-solid and solid asphalt materials and asphalt binders include Test Methods D3289, D3142/D3142M, and D70/D70M.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. No other units of measurement are included in this standard, with the exception of temperature measurements. Units provided in degrees Fahrenheit are for reference purposes only. Temperatures given in degrees Celsius are to be considered standard.  
1.3 This test method should not be applied to petroleum distillates other than asphalt and asphalt binders. For the determination of density of all other petroleum distillates and viscous oils, use Test Method D4052 or D5002, or ISO 12185.  
1.4 The text of this standard references notes and footnotes which provide explanatory material. These footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D7552-22(Test Method)
Standard Test Method for Determining the Complex Shear Modulus (G*) of Asphalt Mixtures Using Dynamic Shear Rheometer

SIGNIFICANCE AND USE
5.1 The complex shear modulus of asphalt mixtures is a fundamental property of the material. Test results at critical temperatures (Tcritical) are used for specifications for some mixes. Mixtures with stiffer binders, aged mixes, mixtures with higher amounts of fines (material finer than 75 µ), and mixtures with lower voids all tend to have higher complex shear modulus values than mixtures with less stiff binders, unaged mixes, mixtures with low levels of fines, and higher air voids. In general, mixtures with higher complex shear modulus values at a given service temperature will exhibit lower permanent deformation values than similar mixtures tested at the same temperature that have lower complex shear modulus values.  
Note 2: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers the determination of the complex shear modulus of asphalt mixtures using torsion rectangular geometry on a dynamic shear rheometer (DSR). It is applicable to asphalt mixtures having complex shear modulus values greater than 1 × 104 Pa when tested over a range of temperatures from –40 °C to 76 °C at frequencies of 0.01 to 25 Hz and strains of 0.0005 % to 0.1 %. The determination of complex shear modulus is typically determined at 20 °C to 70 °C at 0.01 % strain at ten discrete frequency values covering 0.01 to 10 Hz. From these data, temperature or frequency master curves can be generated as required. This test method is intended for determining the complex shear modulus of asphalt mixtures as required for specification testing or quality control of asphalt mixture production.  
1.2 This test method is appropriate for laboratory-prepared and compacted mixtures, field-produced and laboratory-compacted mixtures or field cores, regardless of binder type or grade and regardless of whether RAP is used in the mixture. Due to the geometry of the specimens being tested this test method is not applicable to open-graded or SMA mixtures. It has been found to be appropriate for dense-graded mixtures, whether coarse- or fine-graded, with 19 mm or smaller nominal maximum aggregate size.  
1.3 Since a precision estimate for this standard has not been developed, the test method is to be used for research and informational purposes only. Therefore, this standard should not be used for acceptance or rejection of a material for purchasing purposes.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers...

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM D7227/D7227M-22(Practice)
Standard Practice for Rapid Drying of Compacted Asphalt Mixture Specimens Using Vacuum Drying Apparatus

SIGNIFICANCE AND USE
4.1 Specimen dry weight is a critical measure in determination of accurate density and many other tests in the construction and raw materials industries. Drying specimens at room temperature is required for some tests and provides an advantage for other tests to ensure the integrity and to preserve the characteristics of specimens.  
4.2 This practice covers drying compacted asphalt mixture specimens in a vacuum chamber that is capable of keeping the specimen at close to room temperature. A vacuum pump reduces the pressure inside the chamber, thus allowing water to evaporate at low temperature. Since the specimen naturally cools during the evaporation process, making water harder to evaporate, it is important to have proper temperature controls in the chamber to ensure the specimen remains at close to room temperature. Automatic controls within the unit allow the specimen to remain at close to room temperature by periodically allowing a flow of warm and dry air, typically generated by an inline air heater, to enter the vacuum chamber. Cycling between vacuum and airflow conditions allows the specimen to dry in a short period of time. Completely saturated specimens with over 30 g [0.07 lb] of retained water can be dried in about 30 min. For most field cores that are not completely saturated, the drying time is generally less than 15 min.
Note 1: Cycle time (period) can depend on the material composition. Each cycle involves an alternating period of 30 to 180 s of vacuum operation and 30 to 120 s of airflow.  
4.3 This method can be used for 100 mm [4 in.] diameter, 150 mm [6 in.] diameter cylindrical, and cubical compacted asphalt mixture specimens.  
4.4 This method can also be used for drying loose asphalt mixtures, aggregate samples, and other solid specimens. Follow the manufacturer’s recommended procedures for drying specimens other than compacted asphalt mixture specimens.  
4.5 This method can be used to determine moisture content and amount of water loss...
SCOPE
1.1 This practice covers the process of drying compacted asphalt mixture specimens using vacuum drying apparatus.  
1.2 The specimens dried by this practice remain at room temperature, which helps in maintaining specimen integrity during the drying process.  
1.3 This practice can be used for compacted cylindrical and cubical laboratory and field asphalt mixture specimens.  
1.4 This practice can also be used for drying other construction materials such as concrete, soils, aggregates, and loose asphalt mixtures. Use the manufacturer’s recommendations for drying other construction materials.  
1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.6 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D1461-17(2022)(Test Method)
Standard Test Method for Moisture or Volatile Distillates in Asphalt Mixtures

SIGNIFICANCE AND USE
3.1 This test method is used for determining either the amount of moisture or the amount of volatile petroleum distillates in asphalt mixtures.  
3.2 Applicable standards are those in which measurements or calibrations are made, samples are procured, or products are selected.3
SCOPE
1.1 This test method covers the determination, by direct measurement, of moisture or volatile fractions of the asphalt in asphalt mixtures.  
1.2 The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D2171/D2171M-22(Test Method)
Standard Test Method for Viscosity of Asphalts by Vacuum Capillary Viscometer

SIGNIFICANCE AND USE
5.1 The viscosity at 60 °C [140 °F] characterizes flow behavior and may be used for specification requirements for cutback asphalt and asphalt binders.
Note 3: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers procedures for the determination of the apparent viscosity of asphalt binder by vacuum capillary viscometers at 60 °C [140 °F]. It is applicable to materials having viscosities in the range from 0.0036 to over 20 000 Pa·s [0.036 to over 200 000 P].  
Note 1: This test method is suitable for use at other temperatures, but the precision is based on determinations on asphalt binders at 60 °C [140 °F].
Note 2: Modified asphalt binders or asphalt binders that have been conditioned or recovered are typically non-Newtonian under the conditions of this test. The apparent viscosity for non-Newtonian asphalt binders varies with shear rate. When the flow is non-Newtonian in a capillary tube, the shear rate determined using this test method may be invalid. The presence of non-Newtonian behavior for the test conditions of this test can be verified by measuring the viscosity with viscometers having different-sized capillary tubes or with different pressure heads. The defined precision limits in Section 11 may not be applicable to non-Newtonian asphalt binders. Test Method D4957 may be a more applicable method for testing non-Newtonian asphalts.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 Warning—Mercury has been designated by the United States Environmental Protection Agency (EPA) and many state agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury-containing products. See the applicable product Material Safety Data Sheet (MSDS) or Safety Data Sheet (SDS) for details and the EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware that selling mercury, mercury-containing products, or both, in your state may be prohibited by state law.  
1.4 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM D2170/D2170M-22(Test Method)
Standard Test Method for Kinematic Viscosity of Asphalts

SIGNIFICANCE AND USE
5.1 The kinematic viscosity characterizes flow behavior. The method is used to determine the consistency of liquid asphalt as one element in establishing the uniformity of shipments or sources of supply. The specifications are usually at temperatures of 60 and 135 °C.
Note 3: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers procedures for the determination of kinematic viscosity of liquid asphalts, road oils, and distillation residues of liquid asphalts all at 60 °C [140 °F] and of liquid asphalt binders at 135 °C [275 °F] (see table notes, 11.1) in the range from 6 to 100 000 mm2/s [cSt].  
1.2 Results of this test method can be used to calculate viscosity when the density of the test material at the test temperature is known or can be determined. See Annex A1 for the method of calculation.  
Note 1: This test method is suitable for use at other temperatures and at lower kinematic viscosities, but the precision is based on determinations on liquid asphalts and road oils at 60 °C [140 °F] and on asphalt binders at 135 °C [275 °F] only in the viscosity range from 30 to 6000 mm2/s [cSt].
Note 2: Modified asphalt binders or asphalt binders that have been conditioned or recovered are typically non-Newtonian under the conditions of this test. The viscosity determined from this method is under the assumption that asphalt binders behave as Newtonian fluids under the conditions of this test. When the flow is non-Newtonian in a capillary tube, the shear rate determined by this method may be invalid. The presence of non-Newtonian behavior for the test conditions can be verified by measuring the viscosity with viscometers having different-sized capillary tubes. The defined precision limits in 11.1 may not be applicable to non-Newtonian asphalt binders.  
1.3 Warning—Mercury has been designated by the United States Environmental Protection Agency (EPA) and many state agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury-containing products. See the applicable product Material Safety Data Sheet (MSDS) or Safety Data Sheet (SDS) for details and the EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware that selling mercury, mercury-containing products, or both, in your state may be prohibited by state law.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.5 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior ...

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    11 pages
    English language
    sale 15% off