ASTM F3080-14

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F3080 − 14
Standard Practice for
Laser Technologies for Measurement of Cross-Sectional
Shape of Pipeline and Conduit by Non-Rotating Laser
1
Projector and CCTV Camera System
This standard is issued under the fixed designation F3080; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 1.7 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical
1.1 This practice covers the procedure for the measurement
conversions to SI units that are provided for information only
to determine any deviation of the internal surface of installed
and are not considered standard.
pipe compared to the design. The measurements may be used
1.8 This standard does not purport to address all of the
to verify that the installation has met design requirements for
safety concerns, if any, associated with its use. It is the
acceptance or to collect data that will facilitate an assessment
responsibility of the user of this standard to establish appro-
of the condition of pipe or conduit due to structural deviations
priate safety and health practices and determine the applica-
or deterioration.
bility of regulatory limitations prior to use. There are no safety
1.2 This practice applies to all types of pipe material, all
hazards specifically, however, associated with the use of the
types of construction, and pipe shapes.
laser ring profiler specified (listed and labeled as specified in
1.3).
1.3 This practice applies to depressurized and gravity flow
storm sewers, drains, sanitary sewers, and combined sewers
2. Referenced Documents
with diameters from 6 to 72 in. (150 and 1800 mm). The pipe
2
2.1 ASTM Standards:
shall be precleaned and free of debris that would prevent the
E177 Practice for Use of the Terms Precision and Bias in
CCTV camera and laser projector assembly, shown in Fig. 1,
ASTM Test Methods
from moving through the pipe, or adversely affect the accuracy
E691 Practice for Conducting an Interlaboratory Study to
of the survey. Flow or debris, within the line, shall be less than
Determine the Precision of a Test Method
10 % of the nominal pipe diameter or 6 in. in depth whichever
F1216 Practice for Rehabilitation of Existing Pipelines and
is the lesser.
Conduits by the Inversion and Curing of a Resin-
1.4 The laser light projector shall be tested, labeled and
Impregnated Tube
certified to conform to US requirements for CDRH Class 2 or
2.2 Other Standards:
below (not considered to be hazardous) laser products or
IEC 60825-1 Safety of Laser Products – Part 1: Equipment
3
certified to conform to EU requirements for Class 2M or below
Classification and Requirements, Jan 2011.
laser products as per IEC 60825-1, or both.
CDRH Regulations CFR 21, Section I, Subchapter J, Parts
4
1002 to 1040.11
1.5 The profiling process may require physical access to
lines, entry manholes and operations along roadways that may
3. Terminology
include safety hazards.
3.1 Definitions of Terms Specific to This Standard:
1.6 This standard does not include all aspects of pipe
3.1.1 authority, n—party responsible for the generation and
inspection; for example the following are not covered by this
verification of performance to job specification(s) and contract
standard: joint gaps, soil/water infiltration in joints, cracks,
requirements.
holes, surface damage, repairs, corrosion, and structural prob-
lems associated with these.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
1 3
This test method is under the jurisdiction of ASTM Committee F36 on Available from International Electrotechnical Commission (IEC), 3, rue de
Technology and Underground Utilities and is the direct responsibility of Subcom- Varembé, P.O. Box 131, CH-1211 Geneva 20, Switzerland, http://www.iec.ch.
4
mittee F36.20 on Inspection and Renewal of Water and Wastewater Infrastructure. Available from Center for Devices and Radiological Health (CDRH), Food and
Current edition approved Aug. 1, 2014. Published August 2014. DOI: 10.1520/ Drug Administration, 10903 New Hampshire Avenue, WO66-4621, Silver Spring,
F3080–14. MD 20993, http://www.fda.gov.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F3080 − 14
FIG. 1 CCTV—Laser Profiler Assembly
3.1.2 barrel distortion—distortion of an image produced by 3.1.16 l
...