ASTM B197M-93
(Specification)Standard Specification for Copper-Beryllium Alloy Wire [Metric] (Withdrawn 1998)
Standard Specification for Copper-Beryllium Alloy Wire [Metric] (Withdrawn 1998)
SCOPE
1.1 This specification covers copper-beryllium alloy wire in coils, spools, or other than straight lengths, of any uniform cross section. Copper Alloy UNS Nos. C17200 and C17300 are included. Note 1-This specification is the metric companion of Specification B197.
General Information
Relations
![ASTM B197M-93 - Standard Specification for Copper-Beryllium Alloy Wire [Metric] (Withdrawn 1998)](https://cdn.standards.iteh.ai/images/901/15fd4577ff1f473a9f38d66ae40a36fc/page1.jpg "ASTM B197M-93")
Standards Content (Sample)
NOTICE:¬This¬standard¬has¬either¬been¬superseded¬and¬replaced¬by¬a¬new¬version¬or
discontinued.¬Contact¬ASTM¬International¬(www.astm.org)¬for¬the¬latest¬information.
Last ASTM Designation: B 197M – 93
AMERICAN SOCIETY FOR TESTING AND MATERIALS
100 Barr Harbor Dr., West Conshohocken, PA 19428
Reprinted from the Annual Book of ASTM Standards. Copyright ASTM
Standard Specification for
Copper-Beryllium Allo
...
This May Also Interest You
ABSTRACT
This specification covers the requirements for copper-zinc-tin-bismuth alloy rod, bar and wire intended for use in plumbing application and drinking water system. The product shall be manufactured by such hot working, cold working, and annealing processes as to produce a uniform wrought structure in the finished product. Chemical analysis, tensile strength, hardness, and yield strength test methods shall be performed in accordance to the specified requirements.
SCOPE
1.1 This specification establishes the requirements for copper-zinc-tin-bismuth alloy rod, bar and wire of alloy UNS Nos. C49250, C49255, C49260, C49265, C49300, C49340, C49345, C49350, C49355, and C49360 intended for use in plumbing applications and drinking water systems.
1.2 Typically, rod and bar product made to this specification is furnished as straight lengths. Wire (H04) 0.08 in. to 0.3 in. [2 mm to 8 mm inclusive] is furnished in coil form, and H50 shapes.
1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4 The following safety hazard caveat pertains only to the test method(s) described in this specification.
1.4.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Technical specification5 pagesEnglish languagesale 15% off
ABSTRACT
This standard specification establishes the requirements for seamless copper tube coils, suitable for use in refrigeration and air conditioning or other uses, such as oil lines and gasoline lines. The material of manufacture shall be cast billet, bar, tube and so forth of Copper Alloys No. C10200, C10300, C10800, C12000, or C12200. The tube shall be manufactured by such hot and cold working processes needed to produce a homogeneous, uniform wrought structure. The tube shall be cold drawn to the prescribed finish size and wall thickness. When the cold-drawn temper is required, the final drawing operation shall conform to the specified temper properties. When the annealed temper is required, the tube shall be annealed after the final cold draw to the specified temper properties. The product shall conform to the prescribed electrical mass resistivity, tensile strength, yield strength, Rockwell hardness, and expansion. Each tube shall be subjected to an eddy-current test. Particular coppers shall be tested to meet the cuprous oxide, embrittlement, and cleanness requirements.
SCOPE
1.1 This specification establishes the requirements for seamless copper tube in coils, suitable for use in refrigeration and air conditioning or other uses, such as oil lines and gasoline lines.
1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The tube shall be produced of the following coppers:
Copper Alloy
UNS No.
Previously Used
Designation
Type of Copper
C10200
OF
Oxygen-free without residual deoxidantsA
C10300
...
Oxygen-free, extra low phosphorusA
C10800
...
Oxygen-free, low phosphorusA
C12000
DLP
Phosphorized, low residual phosphorus
C12200
DHP
Phosphorized, high residual phosphorus
1.4 The following safety hazards caveat pertains to the test method portion, Section 17, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Technical specification7 pagesEnglish languagesale 15% off
- Technical specification7 pagesEnglish languagesale 15% off
ABSTRACT
This specification covers the requirements for UNS C72900 copper-nickel-tin alloy rods and bars. Products should be manufactured by hot working, cold working, and annealing processes to produce a uniform wrought structure in the finished product. Each product should then be hot or cold worked to the finished size, and if required, should be subsequently annealed to meet the specified temper properties. The tensile strength and Rockwell hardness values from prescribed tests on the products should fall within the required range.
SCOPE
1.1 This specification covers the requirements for copper-nickel-tin alloy UNS No. C72900 rod and bar.
1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following safety hazard caveat pertains only to the test methods described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Technical specification5 pagesEnglish languagesale 15% off
- Technical specification5 pagesEnglish languagesale 15% off
ABSTRACT
This specification establishes the requirements leaded brass plates, sheets, strips, and rolled bars made from UNS C33500, C34000, C34200, C34000, C35000, C35300, or C35600 copper-zinc-lead alloys. Each product should be manufactured by hot or cold working, and annealed if required, to produce a uniform wrought structure that meets the specified temper properties. This specification also contains information on the standard tempers of rolled and annealed materials as well as the required tensile strength, Rockwell hardness, and grain sizes. The Rockwell hardness test can be used to test for general conformity to the specification requirements for temper, tensile strength and grain size.
SCOPE
1.1 This specification establishes the requirements for leaded brass plate, sheet, strip, and rolled bar for general application produced from Copper Alloy UNS Nos. C33500, C34000, C34200, C35000, C35300, and C35600.
1.2 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Technical specification4 pagesEnglish languagesale 15% off
- Technical specification4 pagesEnglish languagesale 15% off
ABSTRACT
This specification establishes the requirements for copper alloys in ingot form that shall be subjected to remelting for the manufacture of castings having the Copper Alloy UNS No. designations specified and enumerated herein. Any material and manufacturing process may be used so long as the alloy is of the required composition and mechanical characteristics, and the yielded ingot is free of defects of a kind that would render it unsuitable for remelting. Materials shall hence be sampled, prepared, and tested accordingly to examine their conformance to mechanical, chemical composition, and weldability requirements.
SCOPE
1.1 This specification covers the requirements for copper alloys in ingot and other forms including granules, nuggets, pellets, or shot for remelting for the manufacturing of castings having the Copper Alloy UNS No. designation, commercial designations and nominal composition shown in Table 1 and Table 2. Product delivered in forms other than ingot shall be upon agreement between the supplier and purchaser.
1.2 A cross reference of Copper Alloy UNS Nos. and copper alloy casting specifications is given in Table 3.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Technical specification14 pagesEnglish languagesale 15% off
- Technical specification14 pagesEnglish languagesale 15% off
ABSTRACT
This specification establishes the requirements for copper-cobalt-beryllium alloy (UNS No. C17500), copper-nickel-beryllium alloy (UNS No. C17510), and copper-nickel-lead-beryllium alloy (UNS No. C17465) rods and bars in straight lengths. Tempers available under this specification are: TB00 (solution heat treated (A)), TF00 (precipitation hardened (AT)), TD04 (solution heat treated and cold worked: hard (H)), and TH04 (hard and precipitation heat treated (HT)). Materials shall be tested and adhere to mechanical (tensile strength and Rockwell hardness), electrical conductivity, and chemical composition requirements.
SCOPE
1.1 This specification establishes the requirements for Copper Alloy UNS Nos. C17500, C17510, C17540, and C17465 rod and bar in straight lengths.
1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard.
1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification.
1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and to determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Technical specification4 pagesEnglish languagesale 15% off
- Technical specification4 pagesEnglish languagesale 15% off
ABSTRACT
This specification covers bullet jacket preform cups made from UNS C22000 wrought copper alloy used for processing Types I-IV and Classes I-II bullet jackets. This standard contains information on chemical composition, grain size and testing requirements for the preform cups.
SIGNIFICANCE AND USE
15.1 For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table and for dimensional tolerances, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29.
Property
Rounded Unit for Observed or Calculated Value
Chemical Composition
Nearest unit in the last right-hand significant digit used in expressing the limiting value
Grain size
Nearest multiple of 0.005 mm
SCOPE
1.1 This specification establishes the requirements for bullet jacket preform cups produced of Copper Alloy UNS No. C22000 for processing into bullet jackets of the following types and classes:
1.1.1 Type I—Caliber 0.30.
1.1.2 Type II—Caliber 0.45.
1.1.3 Type III—Caliber 0.50.
1.1.4 Type IV—As specified in the contract or order.
1.1.5 Class I—Not annealed.
1.1.6 Class II—Annealed.
1.2 Units—The values stated in inch-pound units are to be regarded as standard, except for grain size, which is given in SI units. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Technical specification5 pagesEnglish languagesale 15% off
- Technical specification5 pagesEnglish languagesale 15% off
ABSTRACT
This specification establishes the requirements for sheets and strips of copper-aluminum-silicon-cobalt, copper-nickel-silicon-magnesium, copper-nickel-silicon, copper-nickel-aluminum-magnesium, and copper-nickel-tin alloys with Copper Alloy UNS Nos. C19010, C19020, C19025, C63800, C64725, C70250, C70260, and C70265. Materials shall be tested and shall conform to dimensional (thickness, width, length, straightness, and edges), mechanical (tensile and yield strength, elongation, and ductility or formability), electrical resistivity, chemical composition requirements.
SCOPE
1.1 This specification establishes the requirements for2 Copper Alloy UNS Nos. C19002, C19010, C19015, C19020, C19025, C63800, C64725, C70250, C70260, C70265, C70310, and C70350 sheet and strip.
1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification.
1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Technical specification5 pagesEnglish languagesale 15% off
- Technical specification5 pagesEnglish languagesale 15% off
ABSTRACT
This specification establishes the requirements for copper-zinc-lead (leaded red brass or hardware bronze) rods, bars, and shapes of UNS Alloy Nos. C31400, C31600, and C32000 used for screw machine applications. Tempers available to this specification are O60 (soft anneal), H02 (half-hard), and H04 (hard). Materials for manufacture shall be cast billets, logs, or rods of such purity and soundness as to be suitable for processing by hot working, cold-working, straightening, and annealing to produce a uniform wrought structure in the finished product. Tempers available under this specification are O60 (soft anneal), H02 (half-hard), and H04 (hard). Products shall be tested and conform to dimensional (mass, diameter, length, straightness, and shape), mechanical (tensile and yield strength, and elongation), and chemical composition requirements.
SCOPE
1.1 This specification establishes the requirements for copper-zinc-lead (leaded red brass or hardware bronze) rod, bar, and shapes of UNS Copper Alloy Nos. C31400, C31600, and C32000 available for general and screw machine applications.
1.2 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Technical specification4 pagesEnglish languagesale 15% off
- Technical specification4 pagesEnglish languagesale 15% off
SCOPE
1.1 This specification establishes the requirements for copper-beryllium alloy UNS No. C17510 welded tube in straight lengths.
1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification.
1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
- Technical specification7 pagesEnglish languagesale 15% off
- Technical specification7 pagesEnglish languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.