D04.99 - Sustainable Asphalt Pavement Materials and Construction

SCOPE
1.1 This performance specification covers mixtures of water-based latex polymer, mineral aggregates, and optional other admixtures that, when combined, create a weather-protective and aliphatic hydrocarbon-resistant coating over asphalt and other pavements. There are two variations of the coating (Class 1 and Class 2): Class 1, a standard version—typically black but can be other colors, and Class 2, designed to be a solar reflective version.  
1.2 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements for the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 This guide provides guidance as to the appropriate/typical mineralogy observed when iron and steel slag is produced during a variety of processes in the manufacture of iron and steel.  
4.2 Slag can be considered a product based on the mineralogy of samples that are tested using X-ray diffraction, phase recognition and characterization, powdered XRD-Rietveld analysis, and SEM-PARC results, using this guide.
SCOPE
1.1 This standard is intended to provide guidance as to the appropriate/typical mineralogy observed when iron and steel slag, produced during the manufacture of iron and steel, is designated as a product. The included information covers the mineral properties of blast furnace slag and steel slag when they are manufactured in conjunction with the production of iron or steel, or both (Note 1).  
Note 1: This guide is not intended to be used to determine the applicability of iron or steel slag, or both, for various applications. Terminology D8 designates steel slag as a product, while Terminology C125 designates blast furnace slag as a product. Its sole intent is to provide guidance as to the typical mineralogy when the iron or steel slag, or both, is designated as a product.  
1.2 The values stated in SI units are to be regarded as standard. No other units are utilized in this standard.  
1.3 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) should not be considered as requirements of the specification.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 General guidance is provided for electronic thermometers for general temperature measurements typically needed for D04 practices and test methods which need to monitor oven, water and oil bath, and material temperatures during drying, heating, aging, and mixing.  
4.2 All ASTM standards under the management of the D04 Main Committee were individually reviewed, and a list of all Specification E1 mercury thermometers was prepared along with the required temperature range and information about the thermometer placement in each method.  
4.2.1 This specific information was used to identify the most appropriate type(s) of electronic thermometers which can be used to replace mercury thermometers in the current D04 road and paving standards.
SCOPE
1.1 The Interstate Mercury Education and Reduction Clearinghouse (IMERC) and the U.S. Environmental Protection Agency (EPA) are phasing out the use of mercury thermometers because of safety and environmental concerns. This guide was developed to support replacing mercury thermometers in D04 standards with appropriate electronic thermometers.  
1.2 This guide provides assistance for the D04 subcommittees when selecting electronic thermometers for general use in water or oil baths and ovens and as possible replacements for Specification E1 mercury thermometers currently used in D04 road and paving standards. Guidance for using non-mercury liquid thermometers in place of mercury thermometers can be found in Specification E2251.  
1.3 Some guidance is also provided for selecting a handheld infrared thermometer for use in field applications.  
1.4 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this guide.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 This guide provides a list of the standards within Committee D04 that address the use of materials, specifications, and construction practices that could have broader sustainability benefits. This list is current, relative to the approval date of the standard.  
5.2 The standards discussed are listed in the Referenced Documents section.  
5.3 This guide is intended to be used as a reference for an owner, engineer, contractor, or combinations thereof, to identify potential sustainability strategies and the respective material and construction standards and specifications. It is important to note that these standards do not ensure sustainability goals are achieved; rather, they may be useful in determining inputs for sustainability metrics.
SCOPE
1.1 This guide is intended to be a reference for locating specific test methods relating to materials and construction standards within the jurisdiction of Committee D04 on Road and Paving Materials that could be a strategy used to meet project sustainability goals.  
1.2 The guide needs to be reviewed and updated by Subcommittee D04.99 on Sustainable Asphalt Pavement Materials and Construction, on an as-needed basis, to remain viable.  
1.2.1 Additions or deletions to the reference list in Section 2 shall be submitted to Subcommittee D04.99 and balloted.  
1.3 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 This guide provides guidance as to the appropriate/typical mineralogy observed when iron and steel slag is produced during a variety of processes in the manufacture of iron and steel.  
4.2 Slag can be considered a product based on the mineralogy of samples that are tested using X-ray diffraction, phase recognition and characterization, powdered XRD-Rietveld analysis, and SEM-PARC results, using this guide.
SCOPE
1.1 This standard is intended to provide guidance as to the appropriate/typical mineralogy observed when iron and steel slag, produced during the manufacture of iron and steel, is designated as a product. The included information covers the mineral properties of blast furnace slag and steel slag when they are manufactured in conjunction with the production of iron or steel, or both (Note 1).  
Note 1: This guide is not intended to be used to determine the applicability of iron or steel slag, or both, for various applications. Terminology D8 designates steel slag as a product, while Terminology C125 designates blast furnace slag as a product. Its sole intent is to provide guidance as to the typical mineralogy when the iron or steel slag, or both, is designated as a product.  
1.2 The values stated in SI units are to be regarded as standard. No other units are utilized in this standard.  
1.3 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) should not be considered as requirements of the specification.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 General guidance is provided for electronic thermometers for general temperature measurements typically needed for D04 practices and test methods which need to monitor oven, water and oil bath, and material temperatures during drying, heating, aging, and mixing.  
4.2 All ASTM standards under the management of the D04 Main Committee were individually reviewed, and a list of all Specification E1 mercury thermometers was prepared along with the required temperature range and information about the thermometer placement in each method.  
4.2.1 This specific information was used to identify the most appropriate type(s) of electronic thermometers which can be used to replace mercury thermometers in the current D04 road and paving standards.
SCOPE
1.1 The Interstate Mercury Education and Reduction Clearinghouse (IMERC) and the U.S. Environmental Protection Agency (EPA) are phasing out the use of mercury thermometers because of safety and environmental concerns. This guide was developed to support replacing mercury thermometers in D04 standards with appropriate electronic thermometers.  
1.2 This guide provides assistance for the D04 subcommittees when selecting electronic thermometers for general use in water or oil baths and ovens and as possible replacements for Specification E1 mercury thermometers currently used in D04 road and paving standards. Guidance for using non-mercury liquid thermometers in place of mercury thermometers can be found in Specification E2251.  
1.3 Some guidance is also provided for selecting a hand-held infrared thermometer for use in field applications.  
1.4 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this guide.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.