F15.16 - Highchairs and Hook-On Chairs

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the high chair and high chairs created by using a high chair conversion kit and component(s) from another product.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of high chairs.  
Note 1: This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in the high chair or the accidents resulting from abuse and misuse by persons over three years of age.  
1.3 No high chair or high chair conversion kit produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 2: This consumer safety specification includes the following sections:    
Title  
Section  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Calibration and Standardization  
4  
General Requirements  
5  
Compliance When Used With
Conversion Kits  
5.3  
Threaded Fasteners  
5.5  
Latching or Locking Mechanisms  
5.9  
Labeling  
5.10  
Openings  
5.11  
Toys  
5.12  
Performance Requirements  
6  
Protective Components  
6.1  
Removable Tray or Front Torso Support
Performance Integrity  
6.2  
Tray or Front Torso Support Performance –
Pull Test  
6.3  
Static Load  
6.4  
Stability  
6.5  
Exposed Coil Springs  
6.6  
Scissoring, Shearing, and Pinching  
6.7  
Restraint System  
6.8  
Passive Crotch Restraint System  
6.9  
Structural Integrity  
6.10  
Tray Latch Release Mechanisms  
6.11  
Side Containment  
6.12  
Protrusions  
6.13  
Test Methods  
7  
Locking Mechanisms  
7.1  
Protective Components  
7.2  
Tray or Front Torso Support – Drop Test  
7.3  
Tray or Front Torso Support Disengagement –
Horizontal Pull Test  
7.4  
Tray or Front Torso Support Disengagement –
Vertical Pull Test  
7.5  
Static Load Testing  
7.6  
Stability Testing  
7.7  
Restraint System Retention Test  
7.8  
Permanency of Labels and Warnings  
7.9  
Dynamic High Chair Test  
7.10  
Completely Bounded Openings  
7.11  
Tray Latch Release Mechanism – Accessibility  
7.12  
Side Containment Openings  
7.14  
Marking and Labeling  
8  
Instructional Literature  
9  
Keywords  
10  
Rationale  
Appendix X1  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This consumer safety specification establishes the performance requirements and test methods to ensure the satisfactory performance of infant floor seats, which may include a tray, toys, or a restraint system. It seeks to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of infant floor seats by addressing incidents associated with infant floor seats, including injuries, caused by falls and tip-overs from both elevated and floor level surfaces. This specification does not address accidents and injuries resulting from the interaction of older children with children in infant floor seats. It also does not apply to pillow-like infant positioners that are generally constructed from fabric and stuffing for the purposes of positioning or lounging and do not have an active or passive restraint, or infant floor seats that were either blatantly misused or used in a careless manner with disregard to the warning statements and safety instructions provided with each product.
Performance requirements cover stability, structural integrity, occupant retention, and bounded openings, whereas test methods cover removal of protective components, single action release mechanism, stability, static load, dynamic load, restraint system, completely bounded openings, permanency of labels and warnings, and occupant retention. This specification also covers requirements for calibration and standardization, marking and labeling, and instructional literature.
SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of infant floor seats.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of infant floor seats. This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in infant floor seats.  
1.3 For purposes of this consumer safety specification, an infant floor seat is a seat which is placed on the floor that is intended to contain a child who can hold his/her head up unassisted (approximately 4 months of age) until the child can either walk (approximately 12 months of age) or get in and out of the product by themselves. An infant floor seat may include a tray, toys, or a restraint system. This consumer safety specification does not include pillow-like infant positioners that are generally constructed from fabric and stuffing for the purposes of positioning or lounging and do not have an active or passive restraint.  
1.4 No infant floor seat produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This consumer safety specification covers the performance requirements and test methods designed to ensure the satisfactory performance, and hence, minimize injuries to children resulting from normal use and reasonably foreseeable misuse or abuse of portable hook-on chairs. Chairs that conform to this specification shall pass the following performance tests: chair drop test; static load test; seat and seat back disengagement test; chair bounce test; chair pull/push test; restraint system integrity and retention tests; chair assembly test for the latching mechanism to prevent unintentional folding; torque test; tension test; and labeling test. Instructional literature detailing information such as assembly, maintenance, cleaning, operating, folding, and warnings, where applicable, must be included.
SCOPE
1.1 This specification covers the performance requirements and test methods designed to ensure the satisfactory performance of the portable hook-on chair.  
1.2 This specification is intended to minimize injuries to children resulting from normal use and reasonably foreseeable misuse or abuse of chairs.  
1.3 For the purposes of this specification a chair is:  
1.3.1 A seat made for the express purpose of seating and holding a child who can remain in a sitting position due to his or her own coordination.  
1.3.2 Usually a legless seat constructed to locate the occupant at a table in such a position and elevation so that the surface of the table can be used as the feeding surface for the occupant.  
1.3.3 Supported solely by the table on which it is mounted. These chairs are intended for use by children between the ages of six months and three years and who weigh no more than 37 lb (16.8 kg) (95th percentile male at three years).  
1.4 No chair produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all applicable requirements contained herein.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The following precautionary caveat pertains to the test methods portion only, Section 7, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the booster seat.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of booster seats.
Note 1: This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in booster seats.  
1.3 For purposes of this consumer safety specification, a booster seat is a juvenile chair, which is placed on an adult chair to elevate a child to standard dining table height. The booster seat is made for the purpose of containing a child, up to 5 years of age, and normally for the purposes of feeding or eating. A booster seat may be height adjustable and include a reclined position.  
1.4 No booster seat produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the high chair and high chairs created by using a high chair conversion kit and component(s) from another product.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of high chairs.  
Note 1: This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in the high chair or the accidents resulting from abuse and misuse by persons over three years of age.  
1.3 No high chair or high chair conversion kit produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 2: This consumer safety specification includes the following sections:    
Title  
Section  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Calibration and Standardization  
4  
General Requirements  
5  
Compliance When Used With
Conversion Kits  
5.3  
Threaded Fasteners  
5.5  
Latching or Locking Mechanisms  
5.9  
Labeling  
5.10  
Openings  
5.11  
Toys  
5.12  
Performance Requirements  
6  
Protective Components  
6.1  
Removable Tray or Front Torso Support
Performance Integrity  
6.2  
Tray or Front Torso Support Performance –
Pull Test  
6.3  
Static Load  
6.4  
Stability  
6.5  
Exposed Coil Springs  
6.6  
Scissoring, Shearing, and Pinching  
6.7  
Restraint System  
6.8  
Passive Crotch Restraint System  
6.9  
Structural Integrity  
6.10  
Tray Latch Release Mechanisms  
6.11  
Side Containment  
6.12  
Protrusions  
6.13  
Test Methods  
7  
Locking Mechanisms  
7.1  
Protective Components  
7.2  
Tray or Front Torso Support – Drop Test  
7.3  
Tray or Front Torso Support Disengagement –
Horizontal Pull Test  
7.4  
Tray or Front Torso Support Disengagement –
Vertical Pull Test  
7.5  
Static Load Testing  
7.6  
Stability Testing  
7.7  
Restraint System Retention Test  
7.8  
Permanency of Labels and Warnings  
7.9  
Dynamic High Chair Test  
7.10  
Completely Bounded Openings  
7.11  
Tray Latch Release Mechanism – Accessibility  
7.12  
Side Containment Openings  
7.14  
Marking and Labeling  
8  
Instructional Literature  
9  
Keywords  
10  
Rationale  
Appendix X1  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This consumer safety specification covers minimum safety performance requirements, test methods, and requirements for labeling and instructional material to minimize hazards to young children resulting from the normal use and reasonably foreseeable misuse and abuse of expansion gates and expandable enclosures.  
1.2 Products known as expansion gates and expandable enclosures, or by any other name, which are in the scope of this consumer safety specification are intended for young children aged six months through 24 months, and are defined in Section 3.  
1.3 Expansion gates and expandable enclosures defined in Section 3 are for domestic use and are not to be confused with other types of gates or enclosures that may be specifically designed for commercial, institutional, agricultural, pet use, or any other such use.  
1.4 No expansion gate or expandable enclosure as defined in Section 3, that is, produced after the approval date of this consumer safety specification either by label or other means, shall indicate compliance with this specification unless it conforms to all the requirements contained herein.  
1.5 For expediency, expansion gates and expandable enclosures as defined in Section 3 will heretofore be referred to in this consumer safety specification as “gates” and “enclosures” unless referred to definitively.  
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.7 The following pertains only to the test methods portion, Section 7, of this specification.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the high chair and high chairs created by using a high chair conversion kit and component(s) from another product.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of high chairs.  
Note 1: This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in the high chair or the accidents resulting from abuse and misuse by persons over three years of age.  
1.3 No high chair or high chair conversion kit produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
Note 2: This consumer safety specification includes the following sections:    
Title  
Section  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Calibration and Standardization  
4  
General Requirements  
5  
Compliance When Used With
Conversion Kits  
5.3  
Threaded Fasteners  
5.5  
Latching or Locking Mechanisms  
5.9  
Labeling  
5.10  
Openings  
5.11  
Performance Requirements  
6  
Protective Components  
6.1  
Removable Tray or Front Torso Support
Performance Integrity  
6.2  
Tray or Front Torso Support Performance –
Pull Test  
6.3  
Static Load  
6.4  
Stability  
6.5  
Exposed Coil Springs  
6.6  
Scissoring, Shearing, and Pinching  
6.7  
Restraint System  
6.8  
Passive Crotch Restraint System  
6.9  
Structural Integrity  
6.10  
Tray Latch Release Mechanisms  
6.11  
Side Containment  
6.12  
Protrusions  
6.13  
Test Methods  
7  
Locking Mechanisms  
7.1  
Protective Components  
7.2  
Tray or Front Torso Support – Drop Test  
7.3  
Tray or Front Torso Support Disengagement –
Horizontal Pull Test  
7.4  
Tray or Front Torso Support Disengagement –
Vertical Pull Test  
7.5  
Static Load Testing  
7.6  
Stability Testing  
7.7  
Restraint System Retention Test  
7.8  
Permanency of Labels and Warnings  
7.9  
Dynamic High Chair Test  
7.10  
Completely Bounded Openings  
7.11  
Tray Latch Release Mechanism – Accessibility  
7.12  
Side Containment Openings  
7.14  
Marking and Labeling  
8  
Instructional Literature  
9  
Keywords  
10  
Rationale  
Appendix X1  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of infant floor seats.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of infant floor seats. This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in infant floor seats.  
1.3 For purposes of this consumer safety specification, an infant floor seat is a seat which is placed on the floor that is intended to contain a child who can hold his/her head up unassisted (approximately 4 months of age) until the child can either walk (approximately 12 months of age) or get in and out of the product by themselves. An infant floor seat may include a tray, toys, or a restraint system. This consumer safety specification does not include pillow-like infant positioners that are generally constructed from fabric and stuffing for the purposes of positioning or lounging and do not have an active or passive restraint.  
1.4 No infant floor seat produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This consumer safety specification covers minimum safety performance requirements, test methods, and requirements for labeling and instructional material to minimize hazards to young children resulting from the normal use and reasonably foreseeable misuse and abuse of expansion gates and expandable enclosures.  
1.2 Products known as expansion gates and expandable enclosures, or by any other name, which are in the scope of this consumer safety specification are intended for young children aged six months through 24 months, and are defined in Section 3.  
1.3 Expansion gates and expandable enclosures defined in Section 3 are for domestic use and are not to be confused with other types of gates or enclosures that may be specifically designed for commercial, institutional, agricultural, pet use, or any other such use.  
1.4 No expansion gate or expandable enclosure as defined in Section 3, that is, produced after the approval date of this consumer safety specification either by label or other means, shall indicate compliance with this specification unless it conforms to all the requirements contained herein.  
1.5 For expediency, expansion gates and expandable enclosures as defined in Section 3 will heretofore be referred to in this consumer safety specification as “gates” and “enclosures” unless referred to definitively.  
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.7 The following pertains only to the test methods portion, Section 7, of this specification.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of infant floor seats.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of infant floor seats. This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in infant floor seats.  
1.3 For purposes of this consumer safety specification, an infant floor seat is a seat which is placed on the floor that is intended to contain a child who can hold his/her head up unassisted (approximately 4 months of age) until the child can either walk (approximately 12 months of age) or get in and out of the product by themselves. An infant floor seat may include a tray, toys, or a restraint system. This consumer safety specification does not include pillow-like infant positioners that are generally constructed from fabric and stuffing for the purposes of positioning or lounging and do not have an active or passive restraint.  
1.4 No infant floor seat produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of infant floor seats.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of infant floor seats. This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in infant floor seats.  
1.3 For purposes of this consumer safety specification, an infant floor seat is a seat which is placed on the floor that is intended to contain a child who can hold his/her head up unassisted (approximately 4 months of age) until the child can either walk (approximately 12 months of age) or get in and out of the product by themselves. An infant floor seat may include a tray, toys, or a restraint system. This consumer safety specification does not include pillow-like infant positioners that are generally constructed from fabric and stuffing for the purposes of positioning or lounging and do not have an active or passive restraint.  
1.4 No infant floor seat produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the high chair and high chairs created by using a high chair conversion kit and component(s) from another product.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of high chairs.  
Note 1: This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in the high chair or the accidents resulting from abuse and misuse by persons over three years of age.  
1.3 No high chair or high chair conversion kit produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
Note 2: This consumer safety specification includes the following sections:    
Title  
Section  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Calibration and Standardization  
4  
General Requirements  
5  
Compliance When Used With
Conversion Kits  
5.3  
Threaded Fasteners  
5.5  
Latching or Locking Mechanisms  
5.9  
Labeling  
5.10  
Openings  
5.11  
Performance Requirements  
6  
Protective Components  
6.1  
Removable Tray or Front Torso Support
Performance Integrity  
6.2  
Tray or Front Torso Support Performance –
Pull Test  
6.3  
Static Load  
6.4  
Stability  
6.5  
Exposed Coil Springs  
6.6  
Scissoring, Shearing, and Pinching  
6.7  
Restraint System  
6.8  
Passive Crotch Restraint System  
6.9  
Structural Integrity  
6.10  
Tray Latch Release Mechanisms  
6.11  
Side Containment  
6.12  
Protrusions  
6.13  
Test Methods  
7  
Locking Mechanisms  
7.1  
Protective Components  
7.2  
Tray or Front Torso Support – Drop Test  
7.3  
Tray or Front Torso Support Disengagement –
Horizontal Pull Test  
7.4  
Tray or Front Torso Support Disengagement –
Vertical Pull Test  
7.5  
Static Load Testing  
7.6  
Stability Testing  
7.7  
Restraint System Retention Test  
7.8  
Permanency of Labels and Warnings  
7.9  
Dynamic High Chair Test  
7.10  
Completely Bounded Openings  
7.11  
Tray Latch Release Mechanism – Accessibility  
7.12  
Side Containment Openings  
7.14  
Marking and Labeling  
8  
Instructional Literature  
9  
Keywords  
10  
Rationale  
Appendix X1  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the high chair and high chairs created by using a high chair conversion kit and component(s) from another product.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of high chairs.  
Note 1: This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in the high chair or the accidents resulting from abuse and misuse by persons over three years of age.  
1.3 No high chair or high chair conversion kit produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
Note 2: This consumer safety specification includes the following sections:    
Title  
Section  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Calibration and Standardization  
4  
General Requirements  
5  
Compliance When Used With
Conversion Kits  
5.3  
Threaded Fasteners  
5.5  
Latching or Locking Mechanisms  
5.9  
Labeling  
5.10  
Openings  
5.11  
Performance Requirements  
6  
Protective Components  
6.1  
Removable Tray or Front Torso Support
Performance Integrity  
6.2  
Tray or Front Torso Support Performance –
Pull Test  
6.3  
Static Load  
6.4  
Stability  
6.5  
Exposed Coil Springs  
6.6  
Scissoring, Shearing, and Pinching  
6.7  
Restraint System  
6.8  
Passive Crotch Restraint System  
6.9  
Structural Integrity  
6.10  
Tray Latch Release Mechanisms  
6.11  
Side Containment  
6.12  
Test Methods  
7  
Locking Mechanisms  
7.1  
Protective Components  
7.2  
Tray or Front Torso Support – Drop Test  
7.3  
Tray or Front Torso Support Disengagement –
Horizontal Pull Test  
7.4  
Tray or Front Torso Support Disengagement –
Vertical Pull Test  
7.5  
Static Load Testing  
7.6  
Stability Testing  
7.7  
Restraint System Retention Test  
7.8  
Permanency of Labels and Warnings  
7.9  
Dynamic High Chair Test  
7.10  
Completely Bounded Openings  
7.11  
Tray Latch Release Mechanism – Accessibility  
7.12  
Side Containment Openings  
7.14  
Marking and Labeling  
8  
Instructional Literature  
9  
Keywords  
10  
Rationale  
Appendix X1  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the booster seat.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of booster seats.
Note 1: This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in booster seats.  
1.3 For purposes of this consumer safety specification, a booster seat is a juvenile chair, which is placed on an adult chair to elevate a child to standard dining table height. The booster seat is made for the purpose of containing a child, up to 5 years of age, and normally for the purposes of feeding or eating. A booster seat may be height adjustable and include a reclined position.  
1.4 No booster seat produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the booster seat.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of booster seats.
Note 1: This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in booster seats.  
1.3 For purposes of this consumer safety specification, a booster seat is a juvenile chair, which is placed on an adult chair to elevate a child to standard dining table height. The booster seat is made for the purpose of containing a child, up to 5 years of age, and normally for the purposes of feeding or eating. A booster seat may be height adjustable and include a reclined position.  
1.4 No booster seat produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the high chair and high chairs created by using a high chair conversion kit and component(s) from another product.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of high chairs.  
Note 1: This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in the high chair or the accidents resulting from abuse and misuse by persons over three years of age.  
1.3 No high chair or high chair conversion kit produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
Note 2: This consumer safety specification includes the following sections:    
Title  
Section  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Calibration and Standardization  
4  
General Requirements  
5  
Compliance When Used With
Conversion Kits  
5.3  
Threaded Fasteners  
5.5  
Latching or Locking Mechanisms  
5.9  
Labeling  
5.10  
Openings  
5.11  
Performance Requirements  
6  
Protective Components  
6.1  
Removable Tray or Front Torso Support
Performance Integrity  
6.2  
Tray or Front Torso Support Performance –
Pull Test  
6.3  
Static Load  
6.4  
Stability  
6.5  
Exposed Coil Springs  
6.6  
Scissoring, Shearing, and Pinching  
6.7  
Restraint System  
6.8  
Passive Crotch Restraint System  
6.9  
Structural Integrity  
6.10  
Tray Latch Release Mechanisms  
6.11  
Side Containment  
6.12  
Test Methods  
7  
Locking Mechanisms  
7.1  
Protective Components  
7.2  
Tray or Front Torso Support – Drop Test  
7.3  
Tray or Front Torso Support Disengagement –
Horizontal Pull Test  
7.4  
Tray or Front Torso Support Disengagement –
Vertical Pull Test  
7.5  
Static Load Testing  
7.6  
Stability Testing  
7.7  
Restraint System Retention Test  
7.8  
Permanency of Labels and Warnings  
7.9  
Dynamic High Chair Test  
7.10  
Completely Bounded Openings  
7.11  
Tray Latch Release Mechanism – Accessibility  
7.12  
Side Containment Openings  
7.14  
Marking and Labeling  
8  
Instructional Literature  
9  
Keywords  
10  
Rationale  
Appendix X1  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the booster seat.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of booster seats.
Note 1: This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in booster seats.  
1.3 For purposes of this consumer safety specification, a booster seat is a juvenile chair, which is placed on an adult chair to elevate a child to standard dining table height. The booster seat is made for the purpose of containing a child, up to 5 years of age, and normally for the purposes of feeding or eating. A booster seat may be height adjustable and include a reclined position.  
1.4 No booster seat produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers minimum safety performance requirements, test methods, and requirements for labeling and instructional material to minimize hazards to young children resulting from the normal use and reasonably foreseeable misuse and abuse of expansion gates and expandable enclosures.  
1.2 Products known as expansion gates and expandable enclosures, or by any other name, which are in the scope of this consumer safety specification are intended for young children aged six months through 24 months, and are defined in Section 3.  
1.3 Expansion gates and expandable enclosures defined in Section 3 are for domestic use and are not to be confused with other types of gates or enclosures that may be specifically designed for commercial, institutional, agricultural, pet use, or any other such use.  
1.4 No expansion gate or expandable enclosure as defined in Section 3, that is, produced after the approval date of this consumer safety specification either by label or other means, shall indicate compliance with this specification unless it conforms to all the requirements contained herein.  
1.5 For expediency, expansion gates and expandable enclosures as defined in Section 3 will heretofore be referred to in this consumer safety specification as “gates” and “enclosures” unless referred to definitively.  
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.7 The following pertains only to the test methods portion, Section 7, of this specification.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers minimum safety performance requirements, test methods, and requirements for labeling and instructional material to minimize hazards to young children resulting from the normal use and reasonably foreseeable misuse and abuse of expansion gates and expandable enclosures.  
1.2 Products known as expansion gates and expandable enclosures, or by any other name, which are in the scope of this consumer safety specification are intended for young children aged six months through 24 months, and are defined in Section 3.  
1.3 Expansion gates and expandable enclosures defined in Section 3 are for domestic use and are not to be confused with other types of gates or enclosures that may be specifically designed for commercial, institutional, agricultural, pet use, or any other such use.  
1.4 No expansion gate or expandable enclosure as defined in Section 3, that is, produced after the approval date of this consumer safety specification either by label or other means, shall indicate compliance with this specification unless it conforms to all the requirements contained herein.  
1.5 For expediency, expansion gates and expandable enclosures as defined in Section 3 will heretofore be referred to in this consumer safety specification as “gates” and “enclosures” unless referred to definitively.  
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.7 The following pertains only to the test methods portion, Section 7, of this specification.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the high chair and high chairs created by using a high chair conversion kit and component(s) from another product.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of high chairs.  
Note 1: This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in the high chair or the accidents resulting from abuse and misuse by persons over three years of age.  
1.3 No high chair or high chair conversion kit produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
Note 2: This consumer safety specification includes the following sections:    
Title  
Section  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Calibration and Standardization  
4  
General Requirements  
5  
Compliance When Used With
Conversion Kits  
5.3  
Threaded Fasteners  
5.5  
Latching or Locking Mechanisms  
5.9  
Labeling  
5.10  
Openings  
5.11  
Performance Requirements  
6  
Protective Components  
6.1  
Removable Tray or Front Torso Support
Performance Integrity  
6.2  
Tray or Front Torso Support Performance –
Pull Test  
6.3  
Static Load  
6.4  
Stability  
6.5  
Exposed Coil Springs  
6.6  
Scissoring, Shearing, and Pinching  
6.7  
Restraint System  
6.8  
Passive Crotch Restraint System  
6.9  
Structural Integrity  
6.10  
Tray Latch Release Mechanisms  
6.11  
Side Containment  
6.12  
Test Methods  
7  
Locking Mechanisms  
7.1  
Protective Components  
7.2  
Tray or Front Torso Support – Drop Test  
7.3  
Tray or Front Torso Support Disengagement –
Horizontal Pull Test  
7.4  
Tray or Front Torso Support Disengagement –
Vertical Pull Test  
7.5  
Static Load Testing  
7.6  
Stability Testing  
7.7  
Restraint System Retention Test  
7.8  
Permanency of Labels and Warnings  
7.9  
Dynamic High Chair Test  
7.10  
Completely Bounded Openings  
7.11  
Tray Latch Release Mechanism – Accessibility  
7.12  
Side Containment Openings  
7.14  
Labeling and Warnings  
8  
Instructional Literature  
9  
Keywords  
10  
Rationale  
Appendix X1

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the high chair and high chairs created by using a high chair conversion kit and component(s) from another product.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of high chairs.  
Note 1: This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in the high chair or the accidents resulting from abuse and misuse by persons over three years of age.  
1.3 No high chair or high chair conversion kit produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
Note 2: This consumer safety specification includes the following sections:    
Title  
Section  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Calibration and Standardization  
4  
General Requirements  
5  
Compliance When Used With
Conversion Kits  
5.3  
Threaded Fasteners  
5.5  
Latching or Locking Mechanisms  
5.9  
Labeling  
5.10  
Openings  
5.11  
Performance Requirements  
6  
Protective Components  
6.1  
Removable Tray or Front Torso Support
Performance Integrity  
6.2  
Tray or Front Torso Support Performance –
Pull Test  
6.3  
Static Load  
6.4  
Stability  
6.5  
Exposed Coil Springs  
6.6  
Scissoring, Shearing, and Pinching  
6.7  
Restraint System  
6.8  
Passive Crotch Restraint System  
6.9  
Structural Integrity  
6.10  
Tray Latch Release Mechanisms  
6.11  
Side Containment  
6.12  
Test Methods  
7  
Locking Mechanisms  
7.1  
Protective Components  
7.2  
Tray or Front Torso Support – Drop Test  
7.3  
Tray or Front Torso Support Disengagement –
Horizontal Pull Test  
7.4  
Tray or Front Torso Support Disengagement –
Vertical Pull Test  
7.5  
Static Load Testing  
7.6  
Stability Testing  
7.7  
Restraint System Retention Test  
7.8  
Permanency of Labels and Warnings  
7.9  
Dynamic High Chair Test  
7.10  
Completely Bounded Openings  
7.11  
Tray Latch Release Mechanism – Accessibility  
7.12  
Side Containment Openings  
7.14  
Labeling and Warnings  
8  
Instructional Literature  
9  
Keywords  
10  
Rationale  
Appendix X1

SCOPE
1.1 This consumer safety specification covers minimum safety performance requirements, test methods, and requirements for labeling and instructional material to minimize hazards to young children resulting from the normal use and reasonably foreseeable misuse and abuse of expansion gates and expandable enclosures.  
1.2 Products known as expansion gates and expandable enclosures, or by any other name, which are in the scope of this consumer safety specification are intended for young children aged six months through 24 months, and are defined in Section 3.  
1.3 Expansion gates and expandable enclosures defined in Section 3 are for domestic use and are not to be confused with other types of gates or enclosures that may be specifically designed for commercial, institutional, agricultural, pet use, or any other such use.  
1.4 No expansion gate or expandable enclosure as defined in Section 3, that is, produced after the approval date of this consumer safety specification either by label or other means, shall indicate compliance with this specification unless it conforms to all the requirements contained herein.  
1.5 For expediency, expansion gates and expandable enclosures as defined in Section 3 will heretofore be referred to in this consumer safety specification as “gates” and “enclosures” unless referred to definitively.  
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.7 The following pertains only to the test methods portion, Section 7, of this specification.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers minimum safety performance requirements, test methods, and requirements for labeling and instructional material to minimize hazards to young children resulting from the normal use and reasonably foreseeable misuse and abuse of expansion gates and expandable enclosures.  
1.2 Products known as expansion gates and expandable enclosures, or by any other name, which are in the scope of this consumer safety specification are intended for young children aged six months through 24 months, and are defined in Section 3.  
1.3 Expansion gates and expandable enclosures defined in Section 3 are for domestic use and are not to be confused with other types of gates or enclosures that may be specifically designed for commercial, institutional, agricultural, pet use, or any other such use.  
1.4 No expansion gate or expandable enclosure as defined in Section 3, that is, produced after the approval date of this consumer safety specification either by label or other means, shall indicate compliance with this specification unless it conforms to all the requirements contained herein.  
1.5 For expediency, expansion gates and expandable enclosures as defined in Section 3 will heretofore be referred to in this consumer safety specification as “gates” and “enclosures” unless referred to definitively.  
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.7 The following pertains only to the test methods portion, Section 7, of this specification.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the high chair and high chairs created by using a high chair conversion kit and component(s) from another product.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of high chairs.  
Note 1: This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in the high chair or the accidents resulting from abuse and misuse by persons over three years of age.  
1.3 No high chair or high chair conversion kit produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
Note 2: This consumer safety specification includes the following sections:    
Title  
Section  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Calibration and Standardization  
4  
General Requirements  
5  
Compliance When Used With
Conversion Kits  
5.3  
Threaded Fasteners  
5.5  
Latching or Locking Mechanisms  
5.9  
Labeling  
5.10  
Openings  
5.11  
Performance Requirements  
6  
Protective Components  
6.1  
Removable Tray or Front Torso Support
Performance Integrity  
6.2  
Tray or Front Torso Support Performance –
Pull Test  
6.3  
Static Load  
6.4  
Stability  
6.5  
Exposed Coil Springs  
6.6  
Scissoring, Shearing, and Pinching  
6.7  
Restraint System  
6.8  
Passive Crotch Restraint System  
6.9  
Structural Integrity  
6.10  
Tray Latch Release Mechanisms  
6.11  
Side Containment  
6.12  
Test Methods  
7  
Locking Mechanisms  
7.1  
Protective Components  
7.2  
Tray or Front Torso Support – Drop Test  
7.3  
Tray or Front Torso Support Disengagement –
Horizontal Pull Test  
7.4  
Tray or Front Torso Support Disengagement –
Vertical Pull Test  
7.5  
Static Load Testing  
7.6  
Stability Testing  
7.7  
Restraint System Retention Test  
7.8  
Permanency of Labels and Warnings  
7.9  
Dynamic High Chair Test  
7.10  
Completely Bounded Openings  
7.11  
Tray Latch Release Mechanism – Accessibility  
7.12  
Side Containment Openings  
7.14  
Labeling and Warnings  
8  
Instructional Literature  
9  
Keywords  
10  
Rationale  
Appendix X1

SCOPE
1.1 This consumer safety specification covers minimum safety performance requirements, test methods, and requirements for labeling and instructional material to minimize hazards to young children resulting from the normal use and reasonably foreseeable misuse and abuse of expansion gates and expandable enclosures.  
1.2 Products known as expansion gates and expandable enclosures, or by any other name, which are in the scope of this consumer safety specification are intended for young children aged six months through 24 months, and are defined in Section 3.  
1.3 Expansion gates and expandable enclosures defined in Section 3 are for domestic use and are not to be confused with other types of gates or enclosures that may be specifically designed for commercial, institutional, agricultural, pet use, or any other such use.  
1.4 No expansion gate or expandable enclosure as defined in Section 3, that is, produced after the approval date of this consumer safety specification either by label or other means, shall indicate compliance with this specification unless it conforms to all the requirements contained herein.  
1.5 For expediency, expansion gates and expandable enclosures as defined in Section 3 will heretofore be referred to in this consumer safety specification as “gates” and “enclosures” unless referred to definitively.  
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.7 The following pertains only to the test methods portion, Section 7, of this specification.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This consumer safety specification covers the performance requirements and test methods designed to ensure the satisfactory performance, and hence, minimize injuries to children resulting from normal use and reasonably foreseeable misuse or abuse of portable hook-on chairs. Chairs that conform to this specification shall pass the following performance tests: chair drop test; static load test; seat and seat back disengagement test; chair bounce test; chair pull/push test; restraint system integrity and retention tests; chair assembly test for the latching mechanism to prevent unintentional folding; torque test; tension test; and labeling test. Instructional literature detailing information such as assembly, maintenance, cleaning, operating, folding, and warnings, where applicable, must be included.
SCOPE
1.1 This specification covers the performance requirements and test methods designed to ensure the satisfactory performance of the portable hook-on chair.  
1.2 This specification is intended to minimize injuries to children resulting from normal use and reasonably foreseeable misuse or abuse of chairs.  
1.3 For the purposes of this specification a chair is:  
1.3.1 A seat made for the express purpose of seating and holding a child who can remain in a sitting position due to his or her own coordination.  
1.3.2 Usually a legless seat constructed to locate the occupant at a table in such a position and elevation so that the surface of the table can be used as the feeding surface for the occupant.  
1.3.3 Supported solely by the table on which it is mounted. These chairs are intended for use by children between the ages of six months and three years and who weigh no more than 37 lb (16.8 kg) (95th percentile male at three years).  
1.4 No chair produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all applicable requirements contained herein.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The following precautionary caveat pertains to the test methods portion only, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This consumer safety specification covers the performance requirements and test methods designed to ensure the satisfactory performance, and hence, minimize injuries to children resulting from normal use and reasonably foreseeable misuse or abuse of portable hook-on chairs. Chairs that conform to this specification shall pass the following performance tests: chair drop test; static load test; seat and seat back disengagement test; chair bounce test; chair pull/push test; restraint system integrity and retention tests; chair assembly test for the latching mechanism to prevent unintentional folding; torque test; tension test; and labeling test. Instructional literature detailing information such as assembly, maintenance, cleaning, operating, folding, and warnings, where applicable, must be included.
SCOPE
1.1 This specification covers the performance requirements and test methods designed to ensure the satisfactory performance of the portable hook-on chair.  
1.2 This specification is intended to minimize injuries to children resulting from normal use and reasonably foreseeable misuse or abuse of chairs.  
1.3 For the purposes of this specification a chair is:  
1.3.1 A seat made for the express purpose of seating and holding a child who can remain in a sitting position due to his or her own coordination.  
1.3.2 Usually a legless seat constructed to locate the occupant at a table in such a position and elevation so that the surface of the table can be used as the feeding surface for the occupant.  
1.3.3 Supported solely by the table on which it is mounted. These chairs are intended for use by children between the ages of six months and three years and who weigh no more than 37 lb (16.8 kg) (95th percentile male at three years).  
1.4 No chair produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all applicable requirements contained herein.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The following precautionary caveat pertains to the test methods portion only, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the high chair and high chairs created by using a high chair conversion kit and component(s) from another product.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of high chairs.  
Note 1: This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in the high chair or the accidents resulting from abuse and misuse by persons over three years of age.  
1.3 For purposes of this consumer safety specification, a high chair is a free standing chair that elevates a child to standard dining table height. The high chair is made for the purpose of holding a child, up to 3 years of age, who can remain in a sitting position due to the child’s own coordination, and normally for the purposes of feeding or eating. A high chair may be height adjustable and include a reclined position for infants not able to remain in a sitting position due to the child’s own coordination.  
1.4 No high chair or high chair conversion kit produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
Note 2: This consumer safety specification includes the following sections:    
Title  
Section  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Calibration and Standardization  
4  
General Requirements  
5  
Compliance When Used With
Conversion Kits  
5.3  
Threaded Fasteners  
5.5  
Latching or Locking Mechanisms  
5.9  
Labeling  
5.10  
Openings  
5.11  
Performance Requirements  
6  
Protective Components  
6.1  
Removable Tray or Front Torso Support
Performance Integrity  
6.2  
Tray or Front Torso Support Performance –
Pull Test  
6.3  
Static Load  
6.4  
Stability  
6.5  
Exposed Coil Springs  
6.6  
Scissoring, Shearing, and Pinching  
6.7  
Restraint System  
6.8  
Passive Crotch Restraint System  
6.9  
Structural Integrity  
6.10  
Tray Latch Release Mechanisms  
6.11  
Side Containment  
6.12  
Test Methods  
7  
Locking Mechanisms  
7.1  
Protective Components  
7.2  
Tray or Front Torso Support – Drop Test  
7.3  
Tray or Front Torso Support Disengagement –
Horizontal Pull Test  
7.4  
Tray or Front Torso Support Disengagement –
Vertical Pull Test  
7.5  
Static Load Testing  
7.6  
Stability Testing  
7.7  
Restraint System Retention Test  
7.8  
Permanency of Labels and Warnings  
7.9  
Dynamic High Chair Test  
7.10  
Leg Openings  
7.11  
Tray Latch Release Mechanism – Accessibility  
7.12  
Side Containment Openings  
7.14  
Labeling and Warnings  
8  
Instructional Literature  
9  
Keywords  
10  
Rationale  
Appendix X1

ABSTRACT
This consumer safety specification covers the performance requirements and test methods designed to ensure the satisfactory performance, and hence, minimize injuries to children resulting from normal use and reasonably foreseeable misuse or abuse of portable hook-on chairs. Chairs that conform to this specification shall pass the following performance tests: chair drop test; static load test; seat and seat back disengagement test; chair bounce test; chair pull/push test; restraint system integrity and retention tests; chair assembly test for the latching mechanism to prevent unintentional folding; torque test; tension test; and labeling test. Instructional literature detailing information such as assembly, maintenance, cleaning, operating, folding, and warnings, where applicable, must be included.
SCOPE
1.1 This specification covers the performance requirements and test methods designed to ensure the satisfactory performance of the portable hook-on chair.  
1.2 This specification is intended to minimize injuries to children resulting from normal use and reasonably foreseeable misuse or abuse of chairs.  
1.3 For the purposes of this specification a chair is:  
1.3.1 A seat made for the express purpose of seating and holding a child who can remain in a sitting position due to his or her own coordination.  
1.3.2 Usually a legless seat constructed to locate the occupant at a table in such a position and elevation so that the surface of the table can be used as the feeding surface for the occupant.  
1.3.3 Supported solely by the table on which it is mounted. These chairs are intended for use by children between the ages of six months and three years and who weigh no more than 37 lb (16.8 kg) (95th percentile male at three years).  
1.4 No chair produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all applicable requirements contained herein.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The following precautionary caveat pertains to the test methods portion only, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the high chair.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of high chairs. Note 1—This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in the high chair or the accidents resulting from abuse and misuse by persons over three years of age.  
1.3 For purposes of this consumer safety specification, a high chair is a free standing chair that elevates a child to standard dining table height. The high chair is made for the purpose of holding a child, up to 3 years of age, who can remain in a sitting position due to the child's own coordination, and normally for the purposes of feeding or eating. A high chair may be height adjustable and include a reclined position for infants not able to remain in a sitting position due to the child's own coordination.  
1.4 No high chair produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 2—This consumer safety specification includes the following sections:    
Title  
Section  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Calibration and Standardization  
4  
General Requirements  
5  
Latching or Locking Mechanisms  
5.4  
Labeling  
5.5  
Openings  
5.6  
Performance Requirements  
6  
Protective Components  
6.1  
Removable Tray or Front Torso Support
Performance Integrity  
6.2  
Tray or Front Torso Support Performance –
Pull Test  
6.3  
Static Load  
6.4  
Stability  
6.5  
Exposed Coil Springs  
6.6  
Scissoring, Shearing, and Pinching  
6.7  
Restraint System  
6.8  
Passive Crotch Restraint System  
6.9  
Structural Integrity  
6.10  
Tray Latch Release Mechanisms  
6.11  
Side Containment  
6.12  
Test Methods  
7  
Locking Mechanisms  
7.1  
Protective Components  
7.2  
Tray or Front Torso Support – Drop Test  
7.3  
Tray or Front Torso Support Disengagement –
Horizontal Pull Test  
7.4  
Tray or Front Torso Support Disengagement –
Vertical Pull Test  
7.5  
Static Load Testing  
7.6  
Stability Testing  
7.7  
Restraint System Retention Test  
7.8  
Permanency of Labels and Warnings  
7.9  
Dynamic High Chair Test  
7.10  
Leg Openings  
7.11  
Tray Latch Release Mechanism – Accessibility  
7.12  
Side Containment Openings  
7.14  
Labeling and Warnings  
8  
Instructional Literature  
9  
Keywords  
10  
Rationale  
Appendix X1

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the booster seat.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of booster seats.Note 1—This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in booster seats.  
1.3 For purposes of this consumer safety specification, a booster seat is a juvenile chair, which is placed on an adult chair to elevate a child to standard dining table height. The booster seat is made for the purpose of containing a child, up to 5 years of age, and normally for the purposes of feeding or eating. A booster seat may be height adjustable and include a reclined position.  
1.4 No booster seat produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the high chair.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of high chairs. Note 1—This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in the high chair or the accidents resulting from abuse and misuse by persons over three years of age.  
1.3 For purposes of this consumer safety specification, a high chair is a free standing chair that elevates a child to standard dining table height. The high chair is made for the purpose of holding a child, up to 3 years of age, who can remain in a sitting position due to the child's own coordination, and normally for the purposes of feeding or eating. A high chair may be height adjustable and include a reclined position for infants not able to remain in a sitting position due to the child's own coordination.  
1.4 No high chair produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 2—This consumer safety specification includes the following sections:    
Title  
Section  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Calibration and Standardization  
4  
General Requirements  
5  
Latching or Locking Mechanisms  
5.4  
Nonpaper Labels  
5.5  
Openings  
5.6  
Performance Requirements  
6  
Protective Components  
6.1  
Tray Performance (Drop)  
6.2  
Tray Performance (Pull)  
6.3  
Static Load  
6.4  
Stability  
6.5  
Exposed Coil Springs  
6.6  
Scissoring, Shearing, and Pinching  
6.7  
Restraint System  
6.8  
Passive Crotch Restraint System  
6.9  
Structural Integrity  
6.10  
Tray Latch Release Mechanisms  
6.11  
Side Containment  
6.12  
Test Methods  
7  
Locking Mechanisms  
7.1  
Protective Components  
7.2  
Tray—Drop Test  
7.3  
Tray—Horizontal Force  
7.4  
Tray—Vertical Pull Test  
7.5  
Static Load Testing  
7.6  
Stability Testing  
7.7  
Restraint System Retention Test  
7.8  
Permanency of Labels and Warnings  
7.9  
Dynamic High Chair Test  
7.10  
Leg Openings  
7.11  
Tray Latch Release Mechanism—Accessibility  
7.12  
Side Containment Openings  
7.14  
Labeling and Warnings  
8  
Instructional Literature  
9  
Keywords  
10  
Rationale  
Appendix X1

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the high chair.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of high chairs. Note 1—This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in the high chair or the accidents resulting from abuse and misuse by persons over three years of age.  
1.3 For purposes of this consumer safety specification, a high chair is a free standing chair that elevates a child to standard dining table height. The high chair is made for the purpose of holding a child, up to 3 years of age, who can remain in a sitting position due to the child's own coordination, and normally for the purposes of feeding or eating. A high chair may be height adjustable and include a reclined position for infants not able to remain in a sitting position due to the child's own coordination.  
1.4 No high chair produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 2—This consumer safety specification includes the following sections:    
Title  
Section  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Calibration and Standardization  
4  
General Requirements  
5  
Latching or Locking Mechanisms  
5.4  
Nonpaper Labels  
5.5  
Openings  
5.6  
Performance Requirements  
6  
Protective Components  
6.1  
Tray Performance (Drop)  
6.2  
Tray Performance (Pull)  
6.3  
Static Load  
6.4  
Stability  
6.5  
Exposed Coil Springs  
6.6  
Scissoring, Shearing, and Pinching  
6.7  
Restraint System  
6.8  
Passive Crotch Restraint System  
6.9  
Structural Integrity  
6.10  
Tray Latch Release Mechanisms  
6.11  
Side Containment  
6.12  
Test Methods  
7  
Locking Mechanisms  
7.1  
Protective Components  
7.2  
Tray—Drop Test  
7.3  
Tray—Horizontal Force  
7.4  
Tray—Vertical Pull Test  
7.5  
Static Load Testing  
7.6  
Stability Testing  
7.7  
Restraint System Retention Test  
7.8  
Adhesion Test for Printing  
7.10  
Dynamic High Chair Test  
7.11  
Leg Openings  
7.12  
Tray Latch Release Mechanism—Accessibility  
7.13  
Side Containment Openings  
7.15  
Labeling and Warnings  
8  
Instructional Literature  
9  
Keywords  
10  
Rationale  
Appendix X1

SCOPE
1.1 This consumer safety specification covers minimum safety performance requirements, test methods, and requirements for labeling and instructional material to minimize hazards to young children resulting from the normal use and reasonably foreseeable misuse and abuse of expansion gates and expandable enclosures.  
1.2 Products known as expansion gates and expandable enclosures, or by any other name, which are in the scope of this consumer safety specification are intended for young children aged six months through 24 months, and are defined in Section 3.  
1.3 Expansion gates and expandable enclosures defined in Section 3 are for domestic use and are not to be confused with other types of gates or enclosures that may be specifically designed for commercial, institutional, agricultural, pet use, or any other such use.  
1.4 No expansion gate or expandable enclosure as defined in Section 3, that is, produced after the approval date of this consumer safety specification either by label or other means, shall indicate compliance with this specification unless it conforms to all the requirements contained herein.  
1.5 For expediency, expansion gates and expandable enclosures as defined in Section 3 will heretofore be referred to in this consumer safety specification as “gates” and “enclosures” unless referred to definitively.  
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.7 The following pertains only to the test methods portion, Section 7, of this specification.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the booster seat.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of booster seats.Note 1—This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in booster seats.  
1.3 For purposes of this consumer safety specification, a booster seat is a juvenile chair, which is placed on an adult chair to elevate a child to standard dining table height. The booster seat is made for the purpose of containing a child, up to 5 years of age, and normally for the purposes of feeding or eating. A booster seat may be height adjustable and include a reclined position.  
1.4 No booster seat produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers minimum safety performance requirements, test methods, and requirements for labeling and instructional material to minimize hazards to young children resulting from the normal use and reasonably foreseeable misuse and abuse of expansion gates and expandable enclosures.
1.2 Products known as expansion gates and expandable enclosures, or by any other name, which are in the scope of this consumer safety specification are intended for young children aged six months through 24 months, and are defined in Section 3.
1.3 Expansion gates and expandable enclosures defined in Section 3 are for domestic use and are not to be confused with other types of gates or enclosures that may be specifically designed for commercial, institutional, agricultural, pet use, or any other such use.
1.4 No expansion gate or expandable enclosure as defined in Section 3, that is, produced after the approval date of this consumer safety specification either by label or other means, shall indicate compliance with this specification unless it conforms to all the requirements contained herein.
1.5 For expediency, expansion gates and expandable enclosures as defined in Section 3 will heretofore be referred to in this consumer safety specification as “gates” and “enclosures” unless referred to definitively.
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.7 The following pertains only to the test methods portion, Section 7, of this specification.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the booster seat.
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of booster seats.
Note 1—This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in booster seats.
1.3 For purposes of this consumer safety specification, a booster seat is a juvenile chair, which is placed on an adult chair to elevate a child to standard dining table height. The booster seat is made for the purpose of containing a child, up to 5 years of age, and normally for the purposes of feeding or eating. A booster seat may be height adjustable and include a reclined position.
1.4 No booster seat produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the booster seat.
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of booster seats.
Note 1—This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in booster seats.
1.3 For purposes of this consumer safety specification, a booster seat is a juvenile chair, which is placed on an adult chair to elevate a child to standard dining table height. The booster seat is made for the purpose of containing a child, up to 5 years of age, and normally for the purposes of feeding or eating. A booster seat may be height adjustable and include a reclined position.
1.4 No booster seat produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the high chair.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of high chairs.  
Note 1—This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in the high chair or the accidents resulting from abuse and misuse by persons over three years of age.  
1.3 For purposes of this consumer safety specification, a high chair is a free standing chair that elevates a child to standard dining table height. The high chair is made for the purpose of holding a child, up to 3 years of age, who can remain in a sitting position due to the child's own coordination, and normally for the purposes of feeding or eating. A high chair may be height adjustable and include a reclined position for infants not able to remain in a sitting position due to the child's own coordination.  
1.4 No high chair produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers minimum safety performance requirements, test methods, and requirements for labeling and instructional material to minimize hazards to young children resulting from the normal use and reasonably foreseeable misuse and abuse of expansion gates and expandable enclosures.
1.2 Products known as expansion gates and expandable enclosures, or by any other name, which are in the scope of this consumer safety specification are intended for young children aged six months through 24 months, and are defined in Section 3.
1.3 Expansion gates and expandable enclosures defined in Section 3 are for domestic use and are not to be confused with other types of gates or enclosures that may be specifically designed for commercial, institutional, agricultural, pet use, or any other such use.
1.4 No expansion gate or expandable enclosure as defined in Section 3, that is, produced after the approval date of this consumer safety specification either by label or other means, shall indicate compliance with this specification unless it conforms to all the requirements contained herein.
1.5 For expediency, expansion gates and expandable enclosures as defined in Section 3 will heretofore be referred to in this consumer safety specification as “gates” and “enclosures” unless referred to definitively.
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.7 The following pertains only to the test methods portion, Section 7, of this specification.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the booster seat.
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of booster seats.
Note 1—This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in booster seats.
1.3 For purposes of this consumer safety specification, a booster seat is a juvenile chair, which is placed on an adult chair to elevate a child to standard dining table height. The booster seat is made for the purpose of containing a child, up to 5 years of age, and normally for the purposes of feeding or eating. A booster seat may be height adjustable and include a reclined position.
1.4 No booster seat produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the booster seat.
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of booster seats.
Note 1—This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in booster seats.
1.3 For purposes of this consumer safety specification, a booster seat is a juvenile chair, which is placed on an adult chair to elevate a child to standard dining table height. The booster seat is made for the purpose of containing a child, up to 5 years of age, and normally for the purposes of feeding or eating. A booster seat may be height adjustable and include a reclined position.
1.4 No booster seat produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers minimum safety performance requirements, test methods, and requirements for labeling and instructional material to minimize hazards to young children resulting from the normal use and reasonably foreseeable misuse and abuse of expansion gates and expandable enclosures.
1.2 Products known as expansion gates and expandable enclosures, or by any other name, which are in the scope of this consumer safety specification are intended for young children aged six months through 24 months, and are defined in Section 3.
1.3 Expansion gates and expandable enclosures defined in Section 3 are for domestic use and are not to be confused with other types of gates or enclosures that may be specifically designed for commercial, institutional, agricultural, pet use, or any other such use.
1.4 No expansion gate or expandable enclosure as defined in Section 3, that is, produced after the approval date of this consumer safety specification either by label or other means, shall indicate compliance with this specification unless it conforms to all the requirements contained herein.
1.5 For expediency, expansion gates and expandable enclosures as defined in Section 3 will heretofore be referred to in this consumer safety specification as “gates” and “enclosures” unless referred to definitively.
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.7 The following pertains only to the test methods portion, Section 7, of this specification.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the high chair.  
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of high chairs.  
Note 1—This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in the high chair or the accidents resulting from abuse and misuse by persons over three years of age.  
1.3 For purposes of this consumer safety specification, a high chair is a free standing chair that elevates a child to standard dining table height. The high chair is made for the purpose of holding a child, up to 3 years of age, who can remain in a sitting position due to the child's own coordination, and normally for the purposes of feeding or eating. A high chair may be height adjustable and include a reclined position for infants not able to remain in a sitting position due to the child's own coordination.  
1.4 No high chair produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This consumer safety specification covers the performance requirements and test methods designed to ensure the satisfactory performance, and hence, minimize injuries to children resulting from normal use and reasonably foreseeable misuse or abuse of portable hook-on chairs. Chairs that conform to this specification shall pass the following performance tests: chair drop test; static load test; seat and seat back disengagement test; chair bounce test; chair pull/push test; restraint system integrity and retention tests; chair assembly test for the latching mechanism to prevent unintentional folding; torque test; tension test; and labeling test. Instructional literature detailing information such as assembly, maintenance, cleaning, operating, folding, and warnings, where applicable, must be included.
SCOPE
1.1 This specification covers the performance requirements and test methods designed to ensure the satisfactory performance of the portable hook-on chair.
1.2 This specification is intended to minimize injuries to children resulting from normal use and reasonably foreseeable misuse or abuse of chairs.
1.3 For the purposes of this specification a chair is:
1.3.1 A seat made for the express purpose of seating and holding a child who can remain in a sitting position due to his or her own coordination.
1.3.2 Usually a legless seat constructed to locate the occupant at a table in such a position and elevation so that the surface of the table can be used as the feeding surface for the occupant.
1.3.3 Supported solely by the table on which it is mounted. These chairs are intended for use by children between the ages of six months and three years and who weigh no more than 37 lb (16.8 kg) (95th percentile male at three years).
1.4 No chair produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all applicable requirements contained herein.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 The following precautionary caveat pertains to the test methods portion only, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the booster seat.
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of booster seats.
Note 1—This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in booster seats.
1.3 For purposes of this consumer safety specification, a booster seat is a juvenile chair, which is placed on an adult chair to elevate a child to standard dining table height. The booster seat is made for the purpose of containing a child, up to 5 years of age, and normally for the purposes of feeding or eating. A booster seat may be height adjustable and include a reclined position.
1.4 No booster seat produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the booster seat.
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of booster seats.Note 1
This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in booster seats or the accidents resulting from normal use and reasonably foreseeable misuse or abuse.
1.3 For purposes of this consumer safety specification, a booster seat is a juvenile chair, which is placed on an adult chair to elevate a child to standard dining table height. The booster seat is made for the purpose of containing a child, up to 5 years of age, and normally for the purposes of feeding or eating. A booster seat may be height adjustable and include a reclined position.
1.4 No booster seat produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the high chair.
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of high chairs.
Note 1—This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in the high chair or the accidents resulting from abuse and misuse by persons over three years of age.
1.3 For purposes of this consumer safety specification, a high chair is a free standing chair that elevates a child to standard dining table height. The high chair is made for the purpose of holding a child, up to 3 years of age, who can remain in a sitting position due to the child's own coordination, and normally for the purposes of feeding or eating. A high chair may be height adjustable and include a reclined position for infants not able to remain in a sitting position due to the child's own coordination.
1.4 No high chair produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.
1.5 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.
1.6 The following precautionary caveat pertains only to the test methods portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers minimum safety performance requirements, test methods, and requirements for labeling and instructional material to minimize hazards to young children resulting from the normal use and reasonably foreseeable misuse and abuse of expansion gates and expandable enclosures.
1.2 Products known as expansion gates and expandable enclosures, or by any other name, which are in the scope of this consumer safety specification are intended for young children aged six months through 24 months, and are defined in Section 3.
1.3 Expansion gates and expandable enclosures defined in Section 3 are for domestic use and are not to be confused with other types of gates or enclosures that may be specifically designed for commercial, institutional, agricultural, pet use, or any other such use.
1.4 No expansion gate or expandable enclosure as defined in Section 3, that is, produced after the approval date of this consumer safety specification either by label or other means, shall indicate compliance with this specification unless it conforms to all the requirements contained herein.
1.5 For expediency, expansion gates and expandable enclosures as defined in Section 3 will heretofore be referred to in this consumer safety specification as "gates" and "enclosures" unless referred to definitively.
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
The following pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This consumer safety specification covers the performance requirements and methods of test to ensure the satisfactory performance of the high chair.
1.2 This consumer safety specification is intended to minimize injuries to children resulting from normal usage and reasonably foreseeable misuse or abuse of high chairs. Note 1
This consumer safety specification is not intended to address accidents and injuries resulting from the interaction of older children with children in the high chair or the accidents resulting from abuse and misuse by persons over three years of age.
1.3 For purposes of this consumer safety specification, a high chair is a free standing chair that elevates a child to standard dining table height. The high chair is made for the purpose of holding a child, up to 3 years of age, who can remain in a sitting position due to the child's own coordination, and normally for the purposes of feeding or eating. A high chair may be height adjustable and include a reclined position for infants not able to remain in a sitting position due to the child's own coordination.
1.4 No high chair produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.
1.5 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.
1.6 The following precautionary caveat pertains only to the test method portion, , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.