SIST ISO 6182-5:2018

INTERNATIONAL ISO
STANDARD 6182-5
Third edition
2012-12-01
Fire protection — Automatic
sprinkler systems —
Part 5:
Requirements and test methods for
deluge valves
Protection contre l’incendie — Systèmes d’extinction automatiques de
type sprinkler —
Partie 5: Exigences et méthodes d’essai des postes déluges
Reference number
©
ISO 2012
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any
means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the
address below or ISO’s member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements . 4
4.1 Nominal sizes . 4
4.2 Connections . 4
4.3 Rated working pressure . 4
4.4 Body and cover . 4
4.5 Strength (see 6.8) . 5
4.6 Access for maintenance . 5
4.7 Components . 5
4.8 Leakage (see 6.7) . 6
4.9 Non-metallic components (excluding gaskets, diaphragms, seals and other elastomeric
parts) (see 6.4 & 6.5) . 6
4.10 Sealing assembly elements (see 6.3). 6
4.11 Clearances . 6
4.12 Hydraulic friction loss (see 6.6) . 8
4.13 Endurance (see 6.10). 9
4.14 Operational performance (see 6.9) . 9
4.15 Drains . 9
4.16 Alarms .10
4.17 Valve impairment .10
4.18 Height limitations of wet pilot lines .10
5 Production testing and quality control .11
6 Tests .11
6.1 Samples .11
6.2 Spring and diaphragm test .11
6.3 Sealing element tests (see 4.10) .11
6.4 Warm-water ageing test for non-metallic components (excluding gaskets and seals and
other elastomeric parts) (see 4.9) .12
6.5 Air ageing test for non-metallic components (excluding gaskets and seals and other
elastomeric parts) (see 4.9) .12
6.6 Hydraulic friction loss test (see 4.12) .13
6.7 Valve leakage and deformation test (see 4.8) .13
6.8 Body strength test (see 4.5) .13
6.9 Operational test (see 4.14) .13
6.10 Endurance test (see 4.13) .15
6.11 Anti-reseating test (see 4.7.7) .15
6.12 Salt mist corrosion test .15
7 Marking .16
8 Manufacturer’s installation instructions .17
Annex A (normative) Tolerances .18
Bibliography .19
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 6182-5 was prepared by Technical Committee ISO/TC 21, Equipment for fire protection and fire
fighting, Subcommittee SC 5, Fixed firefighting systems using water.
This third edition cancels and replaces the second edition (ISO 6182-5:2006), which has been
technically revised.
ISO 6182 consists of the following parts, under the general title Fire protection — Automatic sprinkler systems:
— Part 1: Requirements and test methods for sprinklers
— Part 2: Requirements and test methods for wet alarm valves, retard chambers and water motor alarms
— Part 3: Requirements and test methods for dry pipe valves
— Part 4: Requirements and test methods for quick-opening devices
— Part 5: Requirements and test methods for deluge valves
— Part 6: Requirements and test methods for check valves
— Part 7: Requirements and test methods for early suppression fast response (ESFR) sprinklers
— Part 8: Requirements and test methods for pre-action dry alarm valves
— Part 9: Requirements and test methods for water mist nozzles
— Part 10: Requirements and test methods for domestic sprinklers
— Part 11: Requirements and test methods for pipe hangers
— Part 12: Requirements and test methods for grooved-end components for steel pipe systems
iv © ISO 2012 – All rights reserved

INTERNATIONAL STANDARD ISO 6182-5:2012(E)
Fire protection — Automatic sprinkler systems —
Part 5:
Requirements and test methods for deluge valves
1 Scope
This part of ISO 6182 specifies performance requirements, methods of test and marking requirements
for deluge valves and manufacturer’s specified relevant trim used in deluge and pre-action automatic
fire protection systems. Deluge valves covered by these requirements can be operated by hydraulic,
pneumatic, electric, mechanical, manual, or thermal means, or combinations thereof.
Performance and test requirements for other auxiliary components or attachments to deluge valves are
not covered by this part of ISO 6182.
This part of ISO 6182 does not cover thermally operated valves released by heat acting directly on the
valve. This type of valve utilizes a thermal device, such as the link-and-lever arrangement or glass bulb
of a sprinkler, to hold the valve closed. Operation of the thermal device allows the valve to open.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws
and studs with specified property classes — Coarse thread and fine pitch thread
ISO 898-2, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with
specified property classes — Coarse thread and fine pitch thread
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
alarm device
mechanical or electrical device to sound an alarm upon operation of the valve
3.2
anti-reseat latch
mechanism that prevents the sealing assembly from returning to its closed position after operation
3.3
automatic drain
normally open device that automatically drains water from and vents the intermediate chamber of a
valve to the atmosphere when the valve is in the ready position, and limits water flow from the chamber
after the valve has tripped
3.4
auxiliary pressure
pressure acting against an auxiliary diaphragm or piston, taken from either the service pressure or an
external source
3.5
clapper
type of sealing element
NOTE See 3.20.
3.6
corrosion-resistant material
1) ®
metallic material of bronze, brass, Monel metal, austenitic stainless steel, or equivalent, or plastic
material conforming with the requirements of this part of ISO 6182
3.7
deluge system
automatic fire protection system usi
...