SIST EN 300 296-2 V1.4.1:2013
(Main)Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service - Radio equipment using integral antennas intended primarily for analogue speech - Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
General Information
- Abstract
The present document covers the minimum characteristics considered necessary in order to avoid harmful interference and to make acceptable use of the available frequencies. The present document applies to equipment with integral antennas, used in angle modulation systems in the land mobile
service, operating on radio frequencies between 30 MHz and 1 000 MHz, with channel separations of 12,5 kHz, 20 kHz and 25 kHz, and is intended primarily for analogue speech. In the present document different requirements are given for the different radio frequency bands, channel separations, environmental conditions and types of equipment, where appropriate. The present document is complementary to EN 300 086 [i.4], which covers radio equipment with an internal or external RF connector, for use in the land mobile service. The present document may apply to PMR446 equipment as defined in CEPT/ERC/DEC(98)25 [i.6]. Note that PMR446 equipment has a requirement to incorporate a receiver and may have requirements for 180 s maximum transmission time and VOX.
- Status
- Published
- Public Enquiry End Date
- 30-Sep-2012
- Publication Date
- 24-Oct-2013
- Technical Committee
- MOC - Mobile Communications
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 01-Oct-2013
- Due Date
- 06-Dec-2013
- Completion Date
- 25-Oct-2013
Buy Documents
en_30029602v010401c - Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment using integral antennas intended primarily for analogue speech; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
ETSI EN 300 296-2 V1.4.1 (2013-06) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment using integral antennas intended primarily for analogue speech; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
ETSI EN 300 296-2 V1.4.1 (2013-08) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment using integral antennas intended primarily for analogue speech; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
Overview
SIST EN 300 296-2 V1.4.1:2013 sets out the harmonized requirements for electromagnetic compatibility and radio spectrum management for land mobile service radio equipment using integral antennas, intended primarily for analogue speech transmission. Developed under the scope of article 3.2 of the R&TTE Directive (1999/5/EC), this standard is essential for ensuring radio equipment operates within specified frequency bands-from 30 MHz to 1000 MHz-with channel separations of 12.5 kHz, 20 kHz, and 25 kHz. These requirements are designed to avoid harmful interference and ensure efficient, interference-free use of the radio spectrum, supporting product conformity across the EU.
Key Topics
- Electromagnetic Compatibility (EMC): Details on ensuring equipment does not cause or suffer from electromagnetic interference.
- Spectrum Efficiency: Minimum technical criteria to avoid harmful interference and allow effective frequency use.
- Integral Antenna Use: Applies specifically to radio equipment with no external RF connector, using angle modulation.
- Channel Separation and Frequency Bands: Covers equipment operating in designated VHF/UHF frequency bands with specified channel widths.
- Environmental and Operational Requirements: Takes into account varying environmental conditions and types of land mobile radio equipment.
- Analogue Speech Transmission: The standard targets equipment where analogue voice is the primary application.
- PMR446 Compatibility: May include Personal Mobile Radio (PMR446) equipment, referencing CEPT/ERC/DEC(98)25.
- Testing and Compliance: Outlines essential radio test suites and requirements for proving equipment conformity.
Applications
This standard is directly relevant for:
- Manufacturers of Land Mobile Radios: Ensures devices with built-in antennas can be placed on the market across Europe by demonstrating compliance with harmonized technical requirements.
- Certification and Testing Bodies: Provides a framework for conformity assessment-covering transmitter and receiver characteristics, unwanted emissions, sensitivity, selectivity, spurious response rejection, and intermodulation.
- System Integrators and Network Planners: Aids in selecting equipment that meets regulatory requirements for electromagnetic compatibility and spectrum usage.
- PMR446 Equipment: Ensures that consumer and business walkie-talkies or other license-free radios, operating in the harmonized PMR446 band, comply with specific transmission time and VOX requirements.
- Regulators and Notified Bodies: Supports the presumption of conformity for radio equipment under the R&TTE Directive article 3.2.
By applying this standard, stakeholders enable smooth interoperability, reduce the risk of harmful interference, and support a harmonized European radio equipment market.
Related Standards
Several related standards and documents are referenced for comprehensive compliance:
- EN 300 296-1: Specifies the technical characteristics and methods of measurement for the equipment covered by Part 2.
- EN 300 086: Covers similar requirements for land mobile radio equipment with internal or external RF connectors.
- CEPT/ERC/DEC(98)25: Defines the harmonized frequency band for PMR446 analogue equipment.
- ETSI TR 100 028: Provides guidance on uncertainties in measurement of mobile radio equipment characteristics.
- EG 201 399: Guide to the production of harmonized standards for the R&TTE Directive.
For further compliance, references to the R&TTE Directive (1999/5/EC), and particular EMC directives may also be necessary.
Keywords: electromagnetic compatibility, radio spectrum, land mobile service, integral antenna, analogue speech, PMR446, R&TTE Directive, channel separation, frequency allocation, EMC standards, equipment conformity, radio interference, spectrum management.
Buy Documents
en_30029602v010401c - Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment using integral antennas intended primarily for analogue speech; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
ETSI EN 300 296-2 V1.4.1 (2013-06) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment using integral antennas intended primarily for analogue speech; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
ETSI EN 300 296-2 V1.4.1 (2013-08) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment using integral antennas intended primarily for analogue speech; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
Get Certified
Connect with accredited certification bodies for this standard
ANCE
Mexican certification and testing association.
Intertek Slovenia
Intertek testing, inspection, and certification services in Slovenia.
LNE (Laboratoire National de Métrologie et d'Essais)
French national laboratory for metrology and testing.
Sponsored listings
Frequently Asked Questions
SIST EN 300 296-2 V1.4.1:2013 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service - Radio equipment using integral antennas intended primarily for analogue speech - Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive". This standard covers: The present document covers the minimum characteristics considered necessary in order to avoid harmful interference and to make acceptable use of the available frequencies. The present document applies to equipment with integral antennas, used in angle modulation systems in the land mobile service, operating on radio frequencies between 30 MHz and 1 000 MHz, with channel separations of 12,5 kHz, 20 kHz and 25 kHz, and is intended primarily for analogue speech. In the present document different requirements are given for the different radio frequency bands, channel separations, environmental conditions and types of equipment, where appropriate. The present document is complementary to EN 300 086 [i.4], which covers radio equipment with an internal or external RF connector, for use in the land mobile service. The present document may apply to PMR446 equipment as defined in CEPT/ERC/DEC(98)25 [i.6]. Note that PMR446 equipment has a requirement to incorporate a receiver and may have requirements for 180 s maximum transmission time and VOX.
The present document covers the minimum characteristics considered necessary in order to avoid harmful interference and to make acceptable use of the available frequencies. The present document applies to equipment with integral antennas, used in angle modulation systems in the land mobile service, operating on radio frequencies between 30 MHz and 1 000 MHz, with channel separations of 12,5 kHz, 20 kHz and 25 kHz, and is intended primarily for analogue speech. In the present document different requirements are given for the different radio frequency bands, channel separations, environmental conditions and types of equipment, where appropriate. The present document is complementary to EN 300 086 [i.4], which covers radio equipment with an internal or external RF connector, for use in the land mobile service. The present document may apply to PMR446 equipment as defined in CEPT/ERC/DEC(98)25 [i.6]. Note that PMR446 equipment has a requirement to incorporate a receiver and may have requirements for 180 s maximum transmission time and VOX.
SIST EN 300 296-2 V1.4.1:2013 is classified under the following ICS (International Classification for Standards) categories: 33.060.99 - Other equipment for radiocommunications; 33.070.01 - Mobile services in general; 33.100.01 - Electromagnetic compatibility in general. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 300 296-2 V1.4.1:2013 is associated with the following European legislation: EU Directives/Regulations: 1999/5/EC, 2005-01-1864, TRRTP124. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
SIST EN 300 296-2 V1.4.1:2013 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
Draft ETSI EN 300 296-2 V1.4.1 (2012-07)
Harmonized European Standard
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land Mobile Service;
Radio equipment using integral antennas
intended primarily for analogue speech;
Part 2: Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive
2 Draft ETSI EN 300 296-2 V1.4.1 (2012-07)
Reference
REN/ERM-TGDMR-303
Keywords
analogue, mobile, PMR, radio, regulation, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2012.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 Draft ETSI EN 300 296-2 V1.4.1 (2012-07)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions, symbols and abbreviations . 7
3.1 Definitions . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 Technical specifications . 7
4.1 Environmental profile . 7
4.2 Transmitter requirements . 7
4.2.1 Frequency error . 7
4.2.1.1 Definition . 7
4.2.1.2 Limit . 7
4.2.1.3 Methods of measurement . 7
4.2.2 Effective radiated power . 7
4.2.2.1 Definition . 7
4.2.2.2 Limit . 8
4.2.2.3 Methods of measurement . 8
4.2.3 Maximum permissible frequency deviation . 8
4.2.3.1 Definition . 8
4.2.3.2 Limit . 8
4.2.3.3 Methods of measurement . 8
4.2.4 Adjacent and alternate channel power . 8
4.2.4.1 Definition . 8
4.2.4.2 Limit . 8
4.2.4.3 Methods of measurement . 8
4.2.5 Radiated unwanted emissions in the spurious domain . 8
4.2.5.1 Definition . 8
4.2.5.2 Limit . 8
4.2.5.3 Methods of measurement . 8
4.2.6 Voice operated transmission . 8
4.2.6.1 Definition . 8
4.2.6.2 Limit . 9
4.2.6.3 Methods of measurement . 9
4.3 Receiver requirements . 9
4.3.1 Average usable sensitivity (field strength, speech) . 9
4.3.1.1 Definition . 9
4.3.1.2 Limit . 9
4.3.1.3 Method of measurement . 9
4.3.2 Co-channel rejection . 9
4.3.2.1 Definition . 9
4.3.2.2 Limit . 9
4.3.2.3 Method of measurement . 9
4.3.3 Adjacent channel selectivity . 9
4.3.3.1 Definition . 9
4.3.3.2 Limit . 9
4.3.3.3 Method of measurement . 9
4.3.4 Spurious response rejection . 10
4.3.4.1 Definition . 10
ETSI
4 Draft ETSI EN 300 296-2 V1.4.1 (2012-07)
4.3.4.2 Limit . 10
4.3.4.3 Method of measurement . 10
4.3.5 Intermodulation response rejection . 10
4.3.5.1 Definition . 10
4.3.5.2 Limit . 10
4.3.5.3 Method of measurement . 10
4.3.6 Blocking or desensitization . 10
4.3.6.1 Definition . 10
4.3.6.2 Limit . 10
4.3.6.3 Method of measurement . 10
4.3.7 Spurious radiations . 10
4.3.7.1 Definition . 10
4.3.7.2 Limit . 10
4.3.7.3 Method of measurement . 10
5 Testing for compliance with technical requirements . 11
5.1 Environmental conditions for testing . 11
5.1.1 Normal and extreme test-conditions . 11
5.1.2 Test power source . 11
5.1.3 Choice of samples for test suites . 11
5.2 Interpretation of the measurement results . 11
5.3 Essential radio test suites . 11
5.3.1 Frequency error . 11
5.3.2 Effective radiated power . 11
5.3.3 Maximum frequency deviation . 12
5.3.4 Adjacent and alternate channel power . 12
5.3.5 Radiated unwanted emission in the spurious domain . 12
5.3.6 Spurious radiations . 12
5.3.7 Average usable sensitivity (speech, field strength) . 12
5.3.8 Adjacent channel selectivity . 12
5.3.9 Intermodulation response rejection . 12
5.3.10 Blocking or desensitization . 12
5.4 Other test specifications . 12
5.4.1 Voice operated transmission . 12
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 13
Annex B (informative): Void . 15
Annex C (informative): Bibliography . 16
History . 17
ETSI
5 Draft ETSI EN 300 296-2 V1.4.1 (2012-07)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft Harmonized European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the Public Enquiry phase of the ETSI
standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.2] as amended by Directive 98/48/EC [i.5].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.1].
See article 5.1 of Directive 1999/5/EC [i.1] for information on presumption of conformity and Harmonised Standards or
parts thereof the references of which have been published in the Official Journal of the European Union.
The requirements relevant to Directive 1999/5/EC [i.1] are summarised in annex A.
The present document is part 2 of a multi-part deliverable covering the Land Mobile Service; Radio equipment using
integral antennas intended primarily for analogue speech, as identified below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".
National transposition dates
Date of latest announcement of this EN (doa): 3months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications te
...
Final draft ETSI EN 300 296-2 V1.4.1 (2013-06)
Harmonized European Standard
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land Mobile Service;
Radio equipment using integral antennas
intended primarily for analogue speech;
Part 2: Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive
2 Final draft ETSI EN 300 296-2 V1.4.1 (2013-06)
Reference
REN/ERM-TGDMR-303
Keywords
analogue, mobile, PMR, radio, regulation, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2013.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 Final draft ETSI EN 300 296-2 V1.4.1 (2013-06)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions, symbols and abbreviations . 7
3.1 Definitions . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 Technical specifications . 7
4.1 Environmental profile . 7
4.2 Transmitter requirements . 7
4.2.1 Frequency error . 7
4.2.1.1 Definition . 7
4.2.1.2 Limit . 7
4.2.1.3 Methods of measurement . 7
4.2.2 Effective radiated power . 8
4.2.2.1 Definition . 8
4.2.2.2 Limit . 8
4.2.2.3 Methods of measurement . 8
4.2.3 Maximum permissible frequency deviation . 8
4.2.3.1 Definition . 8
4.2.3.2 Limit . 8
4.2.3.3 Methods of measurement . 8
4.2.4 Adjacent and alternate channel power . 8
4.2.4.1 Definition . 8
4.2.4.2 Limit . 8
4.2.4.3 Methods of measurement . 8
4.2.5 Radiated unwanted emissions in the spurious domain . 8
4.2.5.1 Definition . 8
4.2.5.2 Limit . 8
4.2.5.3 Methods of measurement . 8
4.2.6 Voice operated transmission . 9
4.2.6.1 Definition . 9
4.2.6.2 Limit . 9
4.2.6.3 Methods of measurement . 9
4.2.7 Maxium transmission time . 9
4.2.7.1 Definition . 9
4.2.7.2 Limit . 9
4.2.7.3 Methods of measurement . 9
4.3 Receiver requirements . 9
4.3.1 Average usable sensitivity (field strength, speech) . 9
4.3.1.1 Definition . 9
4.3.1.2 Limit . 9
4.3.1.3 Method of measurement . 9
4.3.2 Co-channel rejection . 9
4.3.2.1 Definition . 9
4.3.2.2 Limit . 9
4.3.2.3 Method of measurement . 10
4.3.3 Adjacent channel selectivity . 10
4.3.3.1 Definition . 10
ETSI
4 Final draft ETSI EN 300 296-2 V1.4.1 (2013-06)
4.3.3.2 Limit . 10
4.3.3.3 Method of measurement . 10
4.3.4 Spurious response rejection . 10
4.3.4.1 Definition . 10
4.3.4.2 Limit . 10
4.3.4.3 Method of measurement . 10
4.3.5 Intermodulation response rejection . 10
4.3.5.1 Definition . 10
4.3.5.2 Limit . 10
4.3.5.3 Method of measurement . 10
4.3.6 Blocking or desensitization . 10
4.3.6.1 Definition . 10
4.3.6.2 Limit . 10
4.3.6.3 Method of measurement . 11
4.3.7 Spurious radiations . 11
4.3.7.1 Definition . 11
4.3.7.2 Limit . 11
4.3.7.3 Method of measurement . 11
5 Testing for compliance with technical requirements . 11
5.1 Environmental conditions for testing . 11
5.1.1 Normal and extreme test-conditions . 11
5.1.2 Test power source . 11
5.1.3 Choice of samples for test suites . 11
5.2 Interpretation of the measurement results . 11
5.3 Essential radio test suites . 12
5.3.1 Frequency error . 12
5.3.2 Effective radiated power . 12
5.3.3 Maximum frequency deviation . 12
5.3.4 Adjacent and alternate channel power . 12
5.3.5 Radiated unwanted emission in the spurious domain . 12
5.3.6 Spurious radiations . 12
5.3.7 Average usable sensitivity (speech, field strength) . 12
5.3.8 Adjacent channel selectivity . 12
5.3.9 Intermodulation response rejection . 12
5.3.10 Blocking or desensitization . 12
5.4 Other test specifications . 12
5.4.1 Voice operated transmission . 12
5.4.2 Maxium transmission time . 13
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 14
Annex B (informative): Bibliography . 16
History . 17
ETSI
5 Final draft ETSI EN 300 296-2 V1.4.1 (2013-06)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This final draft Harmonized European Standard (EN) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the
ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to the mandate M/284 from the European Commission
issued under Council Directive 98/34/EC [i.2] as amended by Directive 98/48/EC [i.5].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.1].
See article 5.1 of Directive 1999/5/EC [i.1] for information on presumption of conformity and Harmonized Standards or
parts thereof the references of which have been published in the Official Journal of the European Union.
The requirements relevant to Directive 1999/5/EC [i.1] are summarized in annex A.
The present document is part 2 of a multi-part deliverable covering the Land Mobile Service; Radio equipment using
integral antennas intended primarily for analogue speech, as identified below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.1]. The
modular structure is shown in EG 201 399 [i.3].
ETSI
6 Final draft ET
...
ETSI EN 300 296-2 V1.4.1 (2013-08)
Harmonized European Standard
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land Mobile Service;
Radio equipment using integral antennas
intended primarily for analogue speech;
Part 2: Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive
2 ETSI EN 300 296-2 V1.4.1 (2013-08)
Reference
REN/ERM-TGDMR-303
Keywords
analogue, mobile, PMR, radio, regulation, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2013.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 ETSI EN 300 296-2 V1.4.1 (2013-08)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions, symbols and abbreviations . 7
3.1 Definitions . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 Technical specifications . 7
4.1 Environmental profile . 7
4.2 Transmitter requirements . 7
4.2.1 Frequency error . 7
4.2.1.1 Definition . 7
4.2.1.2 Limit . 7
4.2.1.3 Methods of measurement . 7
4.2.2 Effective radiated power . 8
4.2.2.1 Definition . 8
4.2.2.2 Limit . 8
4.2.2.3 Methods of measurement . 8
4.2.3 Maximum permissible frequency deviation . 8
4.2.3.1 Definition . 8
4.2.3.2 Limit . 8
4.2.3.3 Methods of measurement . 8
4.2.4 Adjacent and alternate channel power . 8
4.2.4.1 Definition . 8
4.2.4.2 Limit . 8
4.2.4.3 Methods of measurement . 8
4.2.5 Radiated unwanted emissions in the spurious domain . 8
4.2.5.1 Definition . 8
4.2.5.2 Limit . 8
4.2.5.3 Methods of measurement . 8
4.2.6 Voice operated transmission . 9
4.2.6.1 Definition . 9
4.2.6.2 Limit . 9
4.2.6.3 Methods of measurement . 9
4.2.7 Maximum transmission time. 9
4.2.7.1 Definition . 9
4.2.7.2 Limit . 9
4.2.7.3 Methods of measurement . 9
4.3 Receiver requirements . 9
4.3.1 Average usable sensitivity (field strength, speech) . 9
4.3.1.1 Definition . 9
4.3.1.2 Limit . 9
4.3.1.3 Method of measurement . 9
4.3.2 Co-channel rejection . 9
4.3.2.1 Definition . 9
4.3.2.2 Limit . 9
4.3.2.3 Method of measurement . 10
4.3.3 Adjacent channel selectivity . 10
4.3.3.1 Definition . 10
ETSI
4 ETSI EN 300 296-2 V1.4.1 (2013-08)
4.3.3.2 Limit . 10
4.3.3.3 Method of measurement . 10
4.3.4 Spurious response rejection . 10
4.3.4.1 Definition . 10
4.3.4.2 Limit . 10
4.3.4.3 Method of measurement . 10
4.3.5 Intermodulation response rejection . 10
4.3.5.1 Definition . 10
4.3.5.2 Limit . 10
4.3.5.3 Method of measurement . 10
4.3.6 Blocking or desensitization . 10
4.3.6.1 Definition . 10
4.3.6.2 Limit . 10
4.3.6.3 Method of measurement . 11
4.3.7 Spurious radiations . 11
4.3.7.1 Definition . 11
4.3.7.2 Limit . 11
4.3.7.3 Method of measurement . 11
5 Testing for compliance with technical requirements . 11
5.1 Environmental conditions for testing . 11
5.1.1 Normal and extreme test-conditions . 11
5.1.2 Test power source . 11
5.1.3 Choice of samples for test suites . 11
5.2 Interpretation of the measurement results . 11
5.3 Essential radio test suites . 12
5.3.1 Frequency error . 12
5.3.2 Effective radiated power . 12
5.3.3 Maximum frequency deviation . 12
5.3.4 Adjacent and alternate channel power . 12
5.3.5 Radiated unwanted emission in the spurious domain . 12
5.3.6 Spurious radiations . 12
5.3.7 Average usable sensitivity (speech, field strength) . 12
5.3.8 Adjacent channel selectivity . 12
5.3.9 Intermodulation response rejection . 12
5.3.10 Blocking or desensitization . 12
5.4 Other test specifications . 12
5.4.1 Voice operated transmission . 12
5.4.2 Maximum transmission time. 13
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 14
Annex B (informative): Bibliography . 16
History . 17
ETSI
5 ETSI EN 300 296-2 V1.4.1 (2013-08)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been produced by ETSI in response to the mandate M/284 from the European Commission
issued under Council Directive 98/34/EC [i.2] as amended by Directive 98/48/EC [i.5].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.1].
See article 5.1 of Directive 1999/5/EC [i.1] for information on presumption of conformity and Harmonized Standards or
parts thereof the references of which have been published in the Official Journal of the European Union.
The requirements relevant to Directive 1999/5/EC [i.1] are summarized in annex A.
The present document is part 2 of a multi-part deliverable covering the Land Mobile Service; Radio equipment using
integral antennas intended primarily for analogue speech, as identified below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".
National transposition dates
Date of adoption of this EN: 13 August 2013
Date of latest announcement of this EN (doa): 30 November 2013
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 May 2014
Date of withdrawal of any conflicting National Standard (dow): 31 May 2015
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.1]. The
modular structure is shown in EG 201 399 [i.3].
ETSI
6 ETSI EN 300 296-2 V1.4.1 (2013-08)
1 Scope
The pres
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service - Radio equipment using integral antennas intended primarily for analogue speech - Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.070.01Mobilni servisi na splošnoMobile services in general33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 300 296-2 Version 1.4.1SIST EN 300 296-2 V1.4.1:2013en01-november-2013SIST EN 300 296-2 V1.4.1:2013SLOVENSKI
STANDARD
ETSI EN 300 296-2 V1.4.1 (2013-08) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment using integral antennas intended primarily for analogue speech; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
Harmonized European Standard SIST EN 300 296-2 V1.4.1:2013
ETSI ETSI EN 300 296-2 V1.4.1 (2013-08) 2
Reference REN/ERM-TGDMR-303 Keywords analogue, mobile, PMR, radio, regulation, speech ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2013. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 300 296-2 V1.4.1:2013
ETSI ETSI EN 300 296-2 V1.4.1 (2013-08) 3 Contents Intellectual Property Rights . 5 Foreword . 5 Introduction . 5 1 Scope . 6 2 References . 6 2.1 Normative references . 6 2.2 Informative references . 6 3 Definitions, symbols and abbreviations . 7 3.1 Definitions . 7 3.2 Symbols . 7 3.3 Abbreviations . 7 4 Technical specifications . 7 4.1 Environmental profile . 7 4.2 Transmitter requirements . 7 4.2.1 Frequency error . 7 4.2.1.1 Definition . 7 4.2.1.2 Limit . 7 4.2.1.3 Methods of measurement . 7 4.2.2 Effective radiated power . 8 4.2.2.1 Definition . 8 4.2.2.2 Limit . 8 4.2.2.3 Methods of measurement . 8 4.2.3 Maximum permissible frequency deviation . 8 4.2.3.1 Definition . 8 4.2.3.2 Limit . 8 4.2.3.3 Methods of measurement . 8 4.2.4 Adjacent and alternate channel power . 8 4.2.4.1 Definition . 8 4.2.4.2 Limit . 8 4.2.4.3 Methods of measurement . 8 4.2.5 Radiated unwanted emissions in the spurious domain . 8 4.2.5.1 Definition . 8 4.2.5.2 Limit . 8 4.2.5.3 Methods of measurement . 8 4.2.6 Voice operated transmission . 9 4.2.6.1 Definition . 9 4.2.6.2 Limit . 9 4.2.6.3 Methods of measurement . 9 4.2.7 Maximum transmission time. 9 4.2.7.1 Definition . 9 4.2.7.2 Limit . 9 4.2.7.3 Methods of measurement . 9 4.3 Receiver requirements . 9 4.3.1 Average usable sensitivity (field strength, speech) . 9 4.3.1.1 Definition . 9 4.3.1.2 Limit . 9 4.3.1.3 Method of measurement . 9 4.3.2 Co-channel rejection . 9 4.3.2.1 Definition . 9 4.3.2.2 Limit . 9 4.3.2.3 Method of measurement . 10 4.3.3 Adjacent channel selectivity . 10 4.3.3.1 Definition . 10 SIST EN 300 296-2 V1.4.1:2013
ETSI ETSI EN 300 296-2 V1.4.1 (2013-08) 4 4.3.3.2 Limit . 10 4.3.3.3 Method of measurement . 10 4.3.4 Spurious response rejection . 10 4.3.4.1 Definition . 10 4.3.4.2 Limit . 10 4.3.4.3 Method of measurement . 10 4.3.5 Intermodulation response rejection . 10 4.3.5.1 Definition . 10 4.3.5.2 Limit . 10 4.3.5.3 Method of measurement . 10 4.3.6 Blocking or desensitization . 10 4.3.6.1 Definition . 10 4.3.6.2 Limit . 10 4.3.6.3 Method of measurement . 11 4.3.7 Spurious radiations . 11 4.3.7.1 Definition . 11 4.3.7.2 Limit . 11 4.3.7.3 Method of measurement . 11 5 Testing for compliance with technical requirements . 11 5.1 Environmental conditions for testing . 11 5.1.1 Normal and extreme test-conditions . 11 5.1.2 Test power source . 11 5.1.3 Choice of samples for test suites . 11 5.2 Interpretation of the measurement results . 11 5.3 Essential radio test suites . 12 5.3.1 Frequency error . 12 5.3.2 Effective radiated power . 12 5.3.3 Maximum frequency deviation . 12 5.3.4 Adjacent and alternate channel power . 12 5.3.5 Radiated unwanted emission in the spurious domain . 12 5.3.6 Spurious radiations . 12 5.3.7 Average usable sensitivity (speech, field strength) . 12 5.3.8 Adjacent channel selectivity . 12 5.3.9 Intermodulation response rejection . 12 5.3.10 Blocking or desensitization . 12 5.4 Other test specifications . 12 5.4.1 Voice operated transmission . 12 5.4.2 Maximum transmission time. 13 Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) . 14 Annex B (informative): Bibliography . 16 History . 17
ETSI ETSI EN 300 296-2 V1.4.1 (2013-08) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been produced by ETSI in response to the mandate M/284 from the European Commission issued under Council Directive 98/34/EC [i.2] as amended by Directive 98/48/EC [i.5]. The title and reference to the present document are intended to be included in the publication in the Official Journal of the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.1]. See article 5.1 of Directive 1999/5/EC [i.1] for information on presumption of conformity and Harmonized Standards or parts thereof the references of which have been published in the Official Journal of the European Union. The requirements relevant to Directive 1999/5/EC [i.1] are summarized in annex A. The present document is part 2 of a multi-part deliverable covering the Land Mobile Service; Radio equipment using integral antennas intended primarily for analogue speech, as identified below: Part 1: "Technical characteristics and methods of measurement"; Part 2: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".
National transposition dates Date of adoption of this EN: 13 August 2013 Date of latest announcement of this EN (doa): 3
...