SIST EN 300 296-2 V1.3.1:2010
(Main)Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service - Radio equipment using integral antennas intended primarily for analogue speech - Part 2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive
General Information
- Abstract
Revise LBT definition as decided during ERM#38.
The present document covers the minimum characteristics considered necessary in order to avoid harmful interference and to make acceptable use of the available frequencies. The present document applies to equipment with integral antennas, used in angle modulation systems in the land mobile service, operating on radio frequencies between 30 MHz and 1 000 MHz, with channel separations of 12,5 kHz, 20 kHz and 25 kHz, and is intended primarily for analogue speech. In the present document different requirements are given for the different radio frequency bands, channel separations, environmental conditions and types of equipment, where appropriate. The present document is complementary to EN 300 086 [i.4], which covers radio equipment with an internal or external RF connector, for use in the land mobile service.
- Status
- Published
- Publication Date
- 08-Sep-2010
- Technical Committee
- MOC - Mobile Communications
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 11-Aug-2010
- Due Date
- 16-Oct-2010
- Completion Date
- 09-Sep-2010
- Mandate
- M/284
Buy Documents
ETSI EN 300 296-2 V1.3.1 (2010-03) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment using integral antennas intended primarily for analogue speech; Part 2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive
ETSI EN 300 296-2 V1.3.1 (2010-07) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment using integral antennas intended primarily for analogue speech; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
Overview
SIST EN 300 296-2 V1.3.1:2010 describes essential requirements for the electromagnetic compatibility (EMC) and efficient use of the radio spectrum for land mobile service radio equipment. Specifically, this standard focuses on equipment using integral antennas intended primarily for analogue speech, operating in the 30 MHz to 1 000 MHz frequency range with channel separations of 12.5 kHz, 20 kHz, and 25 kHz. As a harmonized European Standard, it covers the essential requirements of Article 3.2 of the R&TTE Directive, ensuring that equipment avoids harmful interference and makes acceptable use of available frequencies.
This standard is complementary to EN 300 086, which covers radio equipment with internal or external RF connectors for analogue speech in land mobile services.
Keywords: land mobile radio, electromagnetic compatibility, analogue speech, EMC, radio spectrum, integral antenna, R&TTE Directive, channel separation
Key Topics
Minimum Requirements for EMC and Spectrum Use
- Defines criteria to prevent harmful interference
- Ensures optimal use of available frequency bands
Equipment Scope
- Applies to radio equipment with integral antennas using angle modulation
- Covers devices intended for analogue speech transmission
- Supports operation across wide frequency bands (30–1,000 MHz)
- Addresses various channel separations
Essential Radio Test Suites
- Outlines required testing for transmitters and receivers
- Specifies conditions for demonstrating compliance
Environmental Conditions
- Establishes operational boundaries based on environmental class
- Compliance must be maintained under all normal and specified extreme conditions
Conditional and Unconditional Requirements
- Differentiates between universally applicable requirements and those dependent on device functionality (e.g., listen-before-transmit features)
Applications
Land Mobile Service radio equipment is vital in settings where robust, reliable analogue voice communication is required, such as:
- Public Safety and Emergency Services: Police, fire, and medical teams use compliant radios to ensure dependable, interference-free voice communication.
- Commercial Fleet and Logistics: Transportation and service industries depend on these standards for efficient group and dispatch communications.
- Industrial Operations: Mining, construction, and utilities rely on standardized land mobile radios for worker coordination and site safety.
- Event and Venue Management: Ensures seamless communication for security and operations staff.
- Governmental and Municipal Services: Standardized radios are used within local and national public service agencies.
By complying with SIST EN 300 296-2 V1.3.1:2010, manufacturers and users help ensure their radio equipment meets European regulatory requirements for EMC and spectrum management, supporting safe and effective analogue voice transmission without disrupting other radio services.
Related Standards
- EN 300 296-1: Technical characteristics and measurement methods for similar equipment with integral antennas.
- EN 300 086: Covers similar requirements for equipment with internal or external RF connectors.
- ETSI TR 100 028: Guide on measurement uncertainties for mobile radio equipment.
- R&TTE Directive (1999/5/EC): European policy governing radio and telecommunications terminal equipment compliance.
- ETSI EG 201 399: Modular structure and guidance for harmonized standards under the R&TTE Directive.
Conclusion:
SIST EN 300 296-2 V1.3.1:2010 is a critical reference for manufacturers, testing laboratories, and regulatory bodies involved with land mobile radio equipment. It ensures devices are not only technically sound but also compliant with European EMC and spectrum use regulations, fostering safe and reliable analogue speech communication across the land mobile service industry.
Buy Documents
ETSI EN 300 296-2 V1.3.1 (2010-03) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment using integral antennas intended primarily for analogue speech; Part 2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive
ETSI EN 300 296-2 V1.3.1 (2010-07) - Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment using integral antennas intended primarily for analogue speech; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
Get Certified
Connect with accredited certification bodies for this standard
ANCE
Mexican certification and testing association.
Intertek Slovenia
Intertek testing, inspection, and certification services in Slovenia.
LNE (Laboratoire National de Métrologie et d'Essais)
French national laboratory for metrology and testing.
Sponsored listings
Frequently Asked Questions
SIST EN 300 296-2 V1.3.1:2010 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service - Radio equipment using integral antennas intended primarily for analogue speech - Part 2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive". This standard covers: Revise LBT definition as decided during ERM#38. The present document covers the minimum characteristics considered necessary in order to avoid harmful interference and to make acceptable use of the available frequencies. The present document applies to equipment with integral antennas, used in angle modulation systems in the land mobile service, operating on radio frequencies between 30 MHz and 1 000 MHz, with channel separations of 12,5 kHz, 20 kHz and 25 kHz, and is intended primarily for analogue speech. In the present document different requirements are given for the different radio frequency bands, channel separations, environmental conditions and types of equipment, where appropriate. The present document is complementary to EN 300 086 [i.4], which covers radio equipment with an internal or external RF connector, for use in the land mobile service.
Revise LBT definition as decided during ERM#38. The present document covers the minimum characteristics considered necessary in order to avoid harmful interference and to make acceptable use of the available frequencies. The present document applies to equipment with integral antennas, used in angle modulation systems in the land mobile service, operating on radio frequencies between 30 MHz and 1 000 MHz, with channel separations of 12,5 kHz, 20 kHz and 25 kHz, and is intended primarily for analogue speech. In the present document different requirements are given for the different radio frequency bands, channel separations, environmental conditions and types of equipment, where appropriate. The present document is complementary to EN 300 086 [i.4], which covers radio equipment with an internal or external RF connector, for use in the land mobile service.
SIST EN 300 296-2 V1.3.1:2010 is classified under the following ICS (International Classification for Standards) categories: 33.060.99 - Other equipment for radiocommunications; 33.070.01 - Mobile services in general; 33.100.01 - Electromagnetic compatibility in general. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 300 296-2 V1.3.1:2010 is associated with the following European legislation: EU Directives/Regulations: 1999/5/EC, 2005-01-1864; Standardization Mandates: M/284. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
SIST EN 300 296-2 V1.3.1:2010 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
Final draft ETSI EN 300 296-2 V1.3.1 (2010-03)
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land Mobile Service;
Radio equipment using integral antennas
intended primarily for analogue speech;
Part 2: Harmonized EN covering essential requirements
of article 3.2 of the R&TTE Directive
2 Final draft ETSI EN 300 296-2 V1.3.1 (2010-03)
Reference
REN/ERM-TGDMR-289-2
Keywords
analogue, mobile, PMR, radio, regulation, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2010.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 Final draft ETSI EN 300 296-2 V1.3.1 (2010-03)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions, symbols and abbreviations . 7
3.1 Definitions . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 Technical specifications . 7
4.1 Environmental profile . 7
4.2 Transmitter requirements . 7
4.2.1 Frequency error . 7
4.2.1.1 Definition . 7
4.2.1.2 Limit . 7
4.2.1.3 Methods of measurement . 7
4.2.2 Effective radiated power . 8
4.2.2.1 Definition . 8
4.2.2.2 Limit . 8
4.2.2.3 Methods of measurement . 8
4.2.3 Maximum permissible frequency deviation . 8
4.2.3.1 Definition . 8
4.2.3.2 Limit . 8
4.2.3.3 Methods of measurement . 8
4.2.4 Adjacent and alternate channel power . 8
4.2.4.1 Definition . 8
4.2.4.2 Limit . 8
4.2.4.3 Methods of measurement . 8
4.2.5 Radiated unwanted emissions in the spurious domain . 8
4.2.5.1 Definition . 8
4.2.5.2 Limit . 8
4.2.5.3 Methods of measurement . 8
4.3 Receiver requirements . 9
4.3.1 Average usable sensitivity (field strength, speech) . 9
4.3.1.1 Definition . 9
4.3.1.2 Limit . 9
4.3.1.3 Method of measurement . 9
4.3.2 Co-channel rejection . 9
4.3.2.1 Definition . 9
4.3.2.2 Limit . 9
4.3.2.3 Method of measurement . 9
4.3.3 Adjacent channel selectivity . 9
4.3.3.1 Definition . 9
4.3.3.2 Limit . 9
4.3.3.3 Method of measurement . 9
4.3.4 Spurious response rejection . 9
4.3.4.1 Definition . 9
4.3.4.2 Limit . 9
4.3.4.3 Method of measurement . 10
4.3.5 Intermodulation response rejection . 10
4.3.5.1 Definition . 10
ETSI
4 Final draft ETSI EN 300 296-2 V1.3.1 (2010-03)
4.3.5.2 Limit . 10
4.3.5.3 Method of measurement . 10
4.3.6 Blocking or desensitization . 10
4.3.6.1 Definition . 10
4.3.6.2 Limit . 10
4.3.6.3 Method of measurement . 10
4.3.7 Spurious radiations . 10
4.3.7.1 Definition . 10
4.3.7.2 Limit . 10
4.3.7.3 Method of measurement . 10
5 Testing for compliance with technical requirements . 11
5.1 Environmental conditions for testing . 11
5.1.1 Normal and extreme test-conditions . 11
5.1.2 Test power source . 11
5.1.3 Choice of samples for test suites . 11
5.2 Interpretation of the measurement results . 11
5.3 Essential radio test suites . 11
5.3.1 Frequency error . 11
5.3.2 Effective radiated power . 11
5.3.3 Maximum frequency deviation . 12
5.3.4 Adjacent and alternate channel power . 12
5.3.5 Radiated unwanted emission in the spurious domain . 12
5.3.6 Spurious radiations . 12
5.4 Other test specifications . 12
5.4.1 Average usable sensitivity (speech, field strength) . 12
5.4.2 Co-channel rejection . 12
5.4.3 Adjacent channel selectivity . 12
5.4.4 Spurious response rejection . 12
5.4.5 Intermodulation response rejection . 12
5.4.6 Blocking or desensitization . 12
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 13
Annex B (informative): The EN title in the official languages . 15
Annex C (informative): Bibliography . 16
History . 17
ETSI
5 Final draft ETSI EN 300 296-2 V1.3.1 (2010-03)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the ETSI standards One-
step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC (as amended) laying down a procedure for the provision of information in the field of
technical standards and regulations [i.2].
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.1] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive") [1].
Technical specifications relevant to Directive 1999/5/EC [i.1] are given in annex A.
The present document is part 2 of a multi-part deliverable covering the Land Mobile Service; Radio equipment using
integral antennas intended primarily for analogue speech, as identified below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [1]. The modular
structure is shown in EG 201 399 [i.3].
ETSI
6 Final draft ETSI EN 300 296-2 V1.3.1 (2010-03)
1 Scope
The present document covers the minimum characteristics considered
...
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land Mobile Service;
Radio equipment using integral antennas
intended primarily for analogue speech;
Part 2: Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive
2 ETSI EN 300 296-2 V1.3.1 (2010-07)
Reference
REN/ERM-TGDMR-289-2
Keywords
analogue, mobile, PMR, radio, regulation, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2010.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 ETSI EN 300 296-2 V1.3.1 (2010-07)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions, symbols and abbreviations . 7
3.1 Definitions . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 Technical specifications . 7
4.1 Environmental profile . 7
4.2 Transmitter requirements . 7
4.2.1 Frequency error . 7
4.2.1.1 Definition . 7
4.2.1.2 Limit . 7
4.2.1.3 Methods of measurement . 7
4.2.2 Effective radiated power . 7
4.2.2.1 Definition . 7
4.2.2.2 Limit . 7
4.2.2.3 Methods of measurement . 8
4.2.3 Maximum permissible frequency deviation . 8
4.2.3.1 Definition . 8
4.2.3.2 Limit . 8
4.2.3.3 Methods of measurement . 8
4.2.4 Adjacent and alternate channel power . 8
4.2.4.1 Definition . 8
4.2.4.2 Limit . 8
4.2.4.3 Methods of measurement . 8
4.2.5 Radiated unwanted emissions in the spurious domain . 8
4.2.5.1 Definition . 8
4.2.5.2 Limit . 8
4.2.5.3 Methods of measurement . 8
4.3 Receiver requirements . 8
4.3.1 Average usable sensitivity (field strength, speech) . 8
4.3.1.1 Definition . 8
4.3.1.2 Limit . 9
4.3.1.3 Method of measurement . 9
4.3.2 Co-channel rejection . 9
4.3.2.1 Definition . 9
4.3.2.2 Limit . 9
4.3.2.3 Method of measurement . 9
4.3.3 Adjacent channel selectivity . 9
4.3.3.1 Definition . 9
4.3.3.2 Limit . 9
4.3.3.3 Method of measurement . 9
4.3.4 Spurious response rejection . 9
4.3.4.1 Definition . 9
4.3.4.2 Limit . 9
4.3.4.3 Method of measurement . 9
4.3.5 Intermodulation response rejection . 9
4.3.5.1 Definition . 9
ETSI
4 ETSI EN 300 296-2 V1.3.1 (2010-07)
4.3.5.2 Limit . 10
4.3.5.3 Method of measurement . 10
4.3.6 Blocking or desensitization . 10
4.3.6.1 Definition . 10
4.3.6.2 Limit . 10
4.3.6.3 Method of measurement . 10
4.3.7 Spurious radiations . 10
4.3.7.1 Definition . 10
4.3.7.2 Limit . 10
4.3.7.3 Method of measurement . 10
5 Testing for compliance with technical requirements . 10
5.1 Environmental conditions for testing . 10
5.1.1 Normal and extreme test-conditions . 10
5.1.2 Test power source . 10
5.1.3 Choice of samples for test suites . 10
5.2 Interpretation of the measurement results . 11
5.3 Essential radio test suites . 11
5.3.1 Frequency error . 11
5.3.2 Effective radiated power . 11
5.3.3 Maximum frequency deviation . 11
5.3.4 Adjacent and alternate channel power . 11
5.3.5 Radiated unwanted emission in the spurious domain . 11
5.3.6 Spurious radiations . 11
5.4 Other test specifications . 11
5.4.1 Average usable sensitivity (speech, field strength) . 12
5.4.2 Co-channel rejection . 12
5.4.3 Adjacent channel selectivity . 12
5.4.4 Spurious response rejection . 12
5.4.5 Intermodulation response rejection . 12
5.4.6 Blocking or desensitization . 12
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 13
Annex B (informative): The EN title in the official languages . 15
Annex C (informative): Bibliography . 16
History . 17
ETSI
5 ETSI EN 300 296-2 V1.3.1 (2010-07)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM).
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC (as amended) laying down a procedure for the provision of information in the field of
technical standards and regulations [i.2].
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.1] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive") [1].
Technical specifications relevant to Directive 1999/5/EC [i.1] are given in annex A.
The present document is part 2 of a multi-part deliverable covering the Land Mobile Service; Radio equipment using
integral antennas intended primarily for analogue speech, as identified below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".
National transposition dates
Date of adoption of this EN: 29 June 2010
Date of latest announcement of this EN (doa): 30 September 2010
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 March 2011
Date of withdrawal of any conflicting National Standard (dow): 31 March 2012
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [1]. The modular
structure is shown in EG 201 399 [i.3].
ETSI
6 ETSI EN 300 296-2 V1.3.1 (2010-07)
1 Scope
The present document covers the minimum characteristics considered nec
...
SLOVENSKI STANDARD
01-oktober-2010
(OHNWURPDJQHWQD]GUXåOMLYRVWLQ]DGHYHY]YH]L]UDGLMVNLPVSHNWURP (50
6WRULWHYNRSHQVNLKPRELOQLKNRPXQLNDFLM5DGLMVNDRSUHPDQDPHQMHQDSUHGYVHP
]DDQDORJQLSUHQRVJRYRUDNLXSRUDEOMDYJUDMHQRDQWHQRGHO +DUPRQL]LUDQL
(1NL]DMHPDELVWYHQH]DKWHYHþOHQDGLUHNWLYH5 77(
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service
- Radio equipment using integral antennas intended primarily for analogue speech - Part
2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive
Ta slovenski standard je istoveten z: EN 300 296-2 Version 1.3.1
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
33.070.01 Mobilni servisi na splošno Mobile services in general
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
Harmonized European Standard (Telecommunications series)
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land Mobile Service;
Radio equipment using integral antennas
intended primarily for analogue speech;
Part 2: Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive
2 ETSI EN 300 296-2 V1.3.1 (2010-07)
Reference
REN/ERM-TGDMR-289-2
Keywords
analogue, mobile, PMR, radio, regulation, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2010.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 ETSI EN 300 296-2 V1.3.1 (2010-07)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions, symbols and abbreviations . 7
3.1 Definitions . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 Technical specifications . 7
4.1 Environmental profile . 7
4.2 Transmitter requirements . 7
4.2.1 Frequency error . 7
4.2.1.1 Definition . 7
4.2.1.2 Limit . 7
4.2.1.3 Methods of measurement . 7
4.2.2 Effective radiated power . 7
4.2.2.1 Definition . 7
4.2.2.2 Limit . 7
4.2.2.3 Methods of measurement . 8
4.2.3 Maximum permissible frequency deviation . 8
4.2.3.1 Definition . 8
4.2.3.2 Limit . 8
4.2.3.3 Methods of measurement . 8
4.2.4 Adjacent and alternate channel power . 8
4.2.4.1 Definition . 8
4.2.4.2 Limit . 8
4.2.4.3 Methods of measurement . 8
4.2.5 Radiated unwanted emissions in the spurious domain . 8
4.2.5.1 Definition . 8
4.2.5.2 Limit . 8
4.2.5.3 Methods of measurement . 8
4.3 Receiver requirements . 8
4.3.1 Average usable sensitivity (field strength, speech) . 8
4.3.1.1 Definition . 8
4.3.1.2 Limit . 9
4.3.1.3 Method of measurement . 9
4.3.2 Co-channel rejection . 9
4.3.2.1 Definition . 9
4.3.2.2 Limit . 9
4.3.2.3 Method of measurement . 9
4.3.3 Adjacent channel selectivity . 9
4.3.3.1 Definition . 9
4.3.3.2 Limit . 9
4.3.3.3 Method of measurement . 9
4.3.4 Spurious response rejection . 9
4.3.4.1 Definition . 9
4.3.4.2 Limit . 9
4.3.4.3 Method of measurement . 9
4.3.5 Intermodulation response rejection . 9
4.3.5.1 Definition . 9
ETSI
4 ETSI EN 300 296-2 V1.3.1 (2010-07)
4.3.5.2 Limit . 10
4.3.5.3 Method of measurement . 10
4.3.6 Blocking or desensitization . 10
4.3.6.1 Definition . 10
4.3.6.2 Limit . 10
4.3.6.3 Method of measurement . 10
4.3.7 Spurious radiations . 10
4.3.7.1 Definition . 10
4.3.7.2 Limit . 10
4.3.7.3 Method of measurement . 10
5 Testing for compliance with technical requirements . 10
5.1 Environmental conditions for testing . 10
5.1.1 Normal and extreme test-conditions . 10
5.1.2 Test power source . 10
5.1.3 Choice of samples for test suites . 10
5.2 Interpretation of the measurement results . 11
5.3 Essential radio test suites . 11
5.3.1 Frequency error . 11
5.3.2 Effective radiated power . 11
5.3.3 Maximum frequency deviation . 11
5.3.4 Adjacent and alternate channel power . 11
5.3.5 Radiated unwanted emission in the spurious domain . 11
5.3.6 Spurious radiations . 11
5.4 Other test specifications . 11
5.4.1 Average usable sensitivity (speech, field strength) . 12
5.4.2 Co-channel rejection . 12
5.4.3 Adjacent channel selectivity . 12
5.4.4 Spurious response rejection . 12
5.4.5 Intermodulation response rejection . 12
5.4.6 Blocking or desensitization . 12
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 13
Annex B (informative): The EN title in the official languages . 15
Annex C (informative): Bibliography . 16
History . 17
ETSI
5 ETSI EN 300 296-2 V1.3.1 (2010-07)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM).
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC (as amended) laying down a procedure for the provision of information in the field of
technical standards and regulations [i.2].
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.1] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive") [1].
Technical specifications relevant to Directive 1999/5/EC [i.1] are given in annex A.
The present document is part 2 of a multi-part deliverable covering the Land Mobile Service; Radio equipment using
integral antennas intended primarily for analogue speech, as identified below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".
National transposition dates
Date of adoption of this EN: 29 June 2010
Date of latest announcement of this EN (doa): 30 September 2010
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 March 2011
Date of withdrawal of any conflicting National Standard (dow
...