SIST EN 1999-1-4:2007/A1:2012
(Amendment)Eurocode 9: Design of aluminium structures - Part 1-4: Cold-formed structural sheeting
General Information
- Abstract
(1)P EN 1999-1-4 gives design requirements for cold-formed trapezoidal aluminium sheeting. It applies to cold-formed aluminium products made from hot rolled or cold rolled sheet or strip that have been cold-formed by such processes as cold-rolled forming or press-breaking. The execution of aluminium structures made of cold-formed sheeting is covered in EN 1090-3.
NOTE The rules in this part complement the rules in other parts of EN 1999-1.
(2) Methods are also given for stressed-skin design using aluminium sheeting as a structural diaphragm.
(3) This part does not apply to cold-formed alumi¬nium profiles like C-, Z- etc profiles nor cold-formed and welded circular or rectangular hollow sections.
(4) EN 1999-1-4 gives methods for design by calculation and for design assisted by testing. The methods for the design by calculation apply only within stated ranges of material properties and geometrical properties for which sufficient experience and test evidence is available. These limitations do not apply to design by testing.
(5) EN 1999-1-4 does not cover load arrangement for loads during execution and main-tenance.
- Status
- Published
- Public Enquiry End Date
- 30-Dec-2010
- Publication Date
- 18-Dec-2011
- Technical Committee
- KON - Structures
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 05-Sep-2011
- Due Date
- 10-Nov-2011
- Completion Date
- 19-Dec-2011
Overview
SIST EN 1999-1-4:2007/A1:2012 is the Slovenian edition of Eurocode 9: Design of aluminium structures - Part 1-4: Cold-formed structural sheeting. Developed under CEN and adopted by SIST, this standard sets the design requirements for cold-formed trapezoidal aluminium sheeting used in structural engineering. It applies specifically to products manufactured from hot or cold-rolled aluminium sheets or strips that are cold-formed through processes such as roll forming or press-breaking. The standard outlines both calculation-based and test-assisted methods for structural design, supporting safe and durable aluminium sheeting constructions.
Key Topics
Scope and Applicability
- Focuses on cold-formed trapezoidal aluminium sheeting
- Excludes cold-formed aluminium profiles (C, Z, etc.) and welded hollow sections
- Complements other parts of EN 1999-1 for comprehensive aluminium structure design
Design Approaches
- Methods for design by calculation within defined material and geometry limits
- Guidance for design assisted by testing, without the same limitations as calculation methods
Structural Applications
- Incorporates stressed-skin (diaphragm) design principles utilizing aluminium sheetings for load transfer as part of the structural system
Product Requirements
- Details on approved aluminium alloys and composite materials, such as EN AW-6025-7072 alclad
- Specification of cladding thickness for durability and structural performance
Limitations
- Does not address load arrangements during structure execution or maintenance operations
- Execution aspects must adhere to EN 1090-3 for aluminium structures
Applications
SIST EN 1999-1-4:2007/A1:2012 is essential for professionals involved in the design and execution of aluminium structures using cold-formed sheeting. Its main applications include:
Industrial and Commercial Buildings:
- Design of lightweight roofing and wall systems relying on cold-formed aluminium sheeting
Architectural Facades:
- Structural sheeting supporting façade elements, providing both functional and aesthetic benefits
Infrastructure Projects:
- Use in bridges or transportation facilities where aluminium sheeting forms part of stressed-skin elements
Prefabricated Buildings:
- Integration with modular building systems utilizing standardised aluminium structural sheeting
By applying the framework and requirements of this standard, designers and engineers ensure structural integrity, durability, and compliance with European and national regulations for aluminium sheeting in construction projects.
Related Standards
For comprehensive application and compliance, SIST EN 1999-1-4:2007/A1:2012 should be used in conjunction with the following standards:
- EN 1999-1 (Eurocode 9): General design rules for aluminium structures, providing the broader context for Part 1-4.
- EN 1090-3: Execution requirements for aluminium structures, covering fabrication and installation.
- EN 1993 and EN 1994 (Eurocodes 3 and 4): Relevant where mixed materials or interfaces with steel and composite structures occur.
- Relevant National Annexes and Amendments: For local regulatory requirements and adaptations.
Practical Value
Utilizing SIST EN 1999-1-4:2007/A1:2012 supports the safe, efficient, and compliant design of aluminium structures using cold-formed sheeting. Adhering to this standard assists architects, structural engineers, manufacturers, and contractors in meeting both technical and regulatory demands, ensuring high quality and resilient aluminium building solutions.
Relations
- Effective Date
- 01-Jan-2011
- Effective Date
- 01-Mar-2028
- Effective Date
- 19-May-2026
- Effective Date
- 09-Feb-2026
- Effective Date
- 09-Feb-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
Get Certified
Connect with accredited certification bodies for this standard
DIBt (Deutsches Institut für Bautechnik)
German Institute for Building Technology.
DIN CERTCO
DIN Group product certification.
Aboma Certification B.V.
Specialized in construction, metal, and transport sectors.
Sponsored listings
Frequently Asked Questions
SIST EN 1999-1-4:2007/A1:2012 is a amendment published by the Slovenian Institute for Standardization (SIST). Its full title is "Eurocode 9: Design of aluminium structures - Part 1-4: Cold-formed structural sheeting". This standard covers: (1)P EN 1999-1-4 gives design requirements for cold-formed trapezoidal aluminium sheeting. It applies to cold-formed aluminium products made from hot rolled or cold rolled sheet or strip that have been cold-formed by such processes as cold-rolled forming or press-breaking. The execution of aluminium structures made of cold-formed sheeting is covered in EN 1090-3. NOTE The rules in this part complement the rules in other parts of EN 1999-1. (2) Methods are also given for stressed-skin design using aluminium sheeting as a structural diaphragm. (3) This part does not apply to cold-formed alumi¬nium profiles like C-, Z- etc profiles nor cold-formed and welded circular or rectangular hollow sections. (4) EN 1999-1-4 gives methods for design by calculation and for design assisted by testing. The methods for the design by calculation apply only within stated ranges of material properties and geometrical properties for which sufficient experience and test evidence is available. These limitations do not apply to design by testing. (5) EN 1999-1-4 does not cover load arrangement for loads during execution and main-tenance.
(1)P EN 1999-1-4 gives design requirements for cold-formed trapezoidal aluminium sheeting. It applies to cold-formed aluminium products made from hot rolled or cold rolled sheet or strip that have been cold-formed by such processes as cold-rolled forming or press-breaking. The execution of aluminium structures made of cold-formed sheeting is covered in EN 1090-3. NOTE The rules in this part complement the rules in other parts of EN 1999-1. (2) Methods are also given for stressed-skin design using aluminium sheeting as a structural diaphragm. (3) This part does not apply to cold-formed alumi¬nium profiles like C-, Z- etc profiles nor cold-formed and welded circular or rectangular hollow sections. (4) EN 1999-1-4 gives methods for design by calculation and for design assisted by testing. The methods for the design by calculation apply only within stated ranges of material properties and geometrical properties for which sufficient experience and test evidence is available. These limitations do not apply to design by testing. (5) EN 1999-1-4 does not cover load arrangement for loads during execution and main-tenance.
SIST EN 1999-1-4:2007/A1:2012 is classified under the following ICS (International Classification for Standards) categories: 91.010.30 - Technical aspects; 91.080.17 - Aluminium structures. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 1999-1-4:2007/A1:2012 has the following relationships with other standards: It is inter standard links to SIST EN 1999-1-4:2007, kSIST FprEN 1999-1-4:2022, SIST-TS CLC/TS 50711:2026, SIST EN 50583-1:2016, SIST EN 50583-2:2016, SIST EN 1996-1-1:2006+A1:2013, SIST EN 1991-1-7:2006. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN 1999-1-4:2007/A1:2012 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2012
1DGRPHãþD
SIST EN 1999-1-4:2007
(YURNRG 3URMHNWLUDQMHNRQVWUXNFLML]DOXPLQLMHYLK]OLWLQGHO +ODGQR
REOLNRYDQHNRQVWUXNFLMVNHSORþHYLQH
Eurocode 9: Design of aluminium structures - Part 1-4: Cold-formed structural sheeting
Eurocode 9: Bemessung und Konstruktion von Aluminiumtragwerken - Teil 1-4:
Kaltgeformte Profiltafeln
Eurocode 9 - Calcul des structures en aluminium - Partie 1-4: Tôles de structure formées
à froid
Ta slovenski standard je istoveten z: EN 1999-1-4:2007/A1:2011
ICS:
91.010.30 7HKQLþQLYLGLNL Technical aspects
91.080.10 Kovinske konstrukcije Metal structures
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 1999-1-4:2007/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2011
ICS 91.010.30; 91.080.10
English Version
Eurocode 9: Design of aluminium structures - Part 1-4: Cold-
formed structural sheeting
Eurocode 9 - Calcul des structures en aluminium - Partie 1- Eurocode 9: Bemessung und Konstruktion von
4: Tôles de structure formées à froid Aluminiumtragwerken - Teil 1-4: Kaltgeformte Profiltafeln
This amendment A1 modifies the European Standard EN 1999-1-4:2007; it was approved by CEN on 8 April 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1999-1-4:2007/A1:2011: E
worldwide for CEN national Members.
SIS
...