SIST EN ISO 787-24:2026
(Main)General methods of test for pigments and extenders - Part 24: Photometric methods for determining the relative tinting strength of coloured pigments and the relative scattering power of white pigments (ISO 787-24:2026)
- Abstract
This document specifies photometric methods of test for comparing in the visible spectrum:
a) the tinting strength of two similar coloured pigments dispersed in an alkyd resin without a drier;
b) the scattering power of two white pigments of the same type dispersed in an alkyd resin without a drier.
This document does not apply to the comparison of coloured pigments that on reduction differ greatly in colour.
- Status
- Published
- Public Enquiry End Date
- 30-Nov-2025
- Publication Date
- 16-Nov-2026
- Technical Committee
- PIP - Pigments and extenders
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 05-Nov-2026
- Due Date
- 10-Jan-2027
- Completion Date
- 17-Nov-2026
SIST EN ISO 787-24:2026 is a SIST standard based on ISO 787-24 for testing pigments and extenders. It specifies photometric methods for comparing the relative tinting strength of similar coloured pigments and the relative scattering power of white pigments dispersed in alkyd resin without a drier. It is used by laboratories, pigment suppliers, paint formulators, and buyers who need an instrumental comparison rather than a visual one.
What does SIST EN ISO 787-24:2026 specify?
SIST EN ISO 787-24:2026 specifies two photometric comparison methods in the visible spectrum: one for coloured pigments and one for white pigments. For coloured pigments, the document compares tinting strength; for white pigments, it compares scattering power.
The document is organized into 10 clauses and 2 informative annexes:
| Annex | What it covers |
|---|---|
| Annex A | The relationship between reflectivity, absorption, and scattering coefficients, including the Kubelka-Munk and Saunderson relations |
| Annex B | K/S values as a function of measured ϱ or R |
Clause 1 sets the scope, Clause 2 lists normative references, Clause 3 gives terms and definitions, Clause 4 explains the principle, Clauses 5 and 6 specify materials and apparatus, Clause 7 covers sampling, Clause 8 gives the procedures, Clause 9 explains expression of results, and Clause 10 sets out the test report.
The scope is limited to pigments dispersed in alkyd resin without a drier. SIST EN ISO 787-24:2026 is not appropriate for comparing coloured pigments that become very different in colour on reduction, so the method is intended for similar colour systems where a meaningful instrumental comparison is possible.
What are the key requirements of SIST EN ISO 787-24:2026?
Principle of the method
SIST EN ISO 787-24:2026 uses photometric measurement as an instrumental alternative to the visual comparison methods in ISO 787-16 and ISO 787-17. That matters in practice because the operator measures reflectivity ϱ or reflectance factor R instead of judging colour by eye.
For coloured and black pigments, Clause 4.2 requires equal masses of the test pigment and an agreed reference pigment to be dispersed separately in the same mass of the same white pigment paste. The measurement is taken at the wavelength where ϱ or R reaches its minimum value, or at an agreed alternative tinting-strength criterion if the parties decide to use one.
For white pigments, Clause 4.3 requires equal masses of the test pigment and the reference pigment to be dispersed in the same mass of the same black pigment paste. The measurement is taken at 550 nm or with a Y-filter, which links the method to the response most useful for white-pigment scattering comparisons.
Materials and preparation
Clause 5 defines the white pigment paste and the black pigment paste used in the method, and it gives acceptance criteria for the alkyd resin, carbon black pigment, and fumed silica used to prepare them. This matters because the pastes have to be stable and reproducible before pigment comparison can be meaningful.
Clause 5 also ties the preparation of the white pigment paste to fineness of grind and storage in an airtight container. For users, that means the paste must be prepared consistently and kept in a condition that preserves its suitability for repeated testing.
Apparatus and sampling
Clause 6 requires a triple-roll mill, an automatic muller, paste film holders, and a spectrophotometer or tristimulus colorimeter. The document allows both measuring geometries including gloss and excluding gloss, so the chosen setup needs to be recorded.
Clause 7 requires representative sampling in accordance with ISO 15528. In practice, this means the test result only represents the lot if the sample taken for testing is itself representative.
Procedure for coloured and black pigments
Clause 8.1 gives the preparation and measurement sequence for relative tinting strength. The test sample and the reference pigment are each dispersed in the white pigment paste, ground in stages, placed in film holders, and measured photometrically.
The clause also allows agreed deviations such as another tinting-strength criterion or another dispersion approach, but these departures have to be reported. That matters because results from different agreements can only be compared if the report tells the reader exactly what was done.
Procedure for white pigments
Clause 8.2 gives the procedure for relative scattering power. It uses a white-pigment mass calculated from the sample density so that the pigment volume concentration is set to the intended level, then disperses the sample in black pigment paste and measures the films photometrically.
For white pigments, the document fixes the practical measurement route more tightly than for coloured pigments: 550 nm or a Y-filter is used for the comparison. That helps keep scattering-power results aligned between laboratories.
Expression of results and reporting
Clause 9 requires conversion from measured ϱ or R to K/S using Annex B. If the measured value includes gloss, the document requires a correction before using the table. The final result is reported as relative tinting strength or relative scattering power as a percentage of the agreed reference pigment.
Clause 10 requires the test report to identify the product and reference pigment, state the measuring geometry, note any deviation from the method, and record the date. For coloured and black pigments, the report includes the calculated relative tinting strength; for white pigments, it includes the density values used for the calculation and the calculated relative scattering power.
What terms does SIST EN ISO 787-24:2026 define?
- Tinting strength - the ability of a colourant to colour other materials because of its absorptive power.
- Relative tinting strength - the percentage ratio of the tinting strength of the test colourant to that of the reference colourant.
- Scattering power - the ability of a pigmented medium to partly diffuse incident light.
- Relative scattering power - the percentage ratio of the scattering index of the test white pigment to that of the reference white pigment.
- Reflectivity ϱ - the reflectance of a paste or paint film thick enough that more thickness no longer changes the reflectance.
- Reflectance factor R - the ratio of reflected radiant flux from the sample to that from a perfect reflecting diffuser under the same irradiation.
- Spectral absorption coefficient K(λ) - the absorbed part of the incident spectral radiant flux per unit thickness, used in Kubelka-Munk analysis.
- Spectral scattering coefficient S(λ) - the outward transfer of spectral radiant flux per unit thickness in Kubelka-Munk analysis.
Who uses SIST EN ISO 787-24:2026?
SIST EN ISO 787-24:2026 is used by pigment manufacturers, paint and varnish laboratories, QC teams, and technical purchasers who need to compare pigment performance. It is relevant in pigments and extenders work, especially where batch-to-batch control, supplier comparison, or specification checking depends on instrumental color measurement.
It also supports formulators who work with alkyd resin systems and need a repeatable way to compare a coloured pigment’s tinting strength or a white pigment’s scattering power. The method is most useful when visual comparison alone would be too subjective for routine quality decisions.
What changed in SIST EN ISO 787-24:2026 from the previous edition?
SIST EN ISO 787-24:2026 cancels and replaces ISO 787-24:1985 and is technically revised. The changes stated for this edition include updated normative references, updated definitions aligned with ISO 18451-1, and an opening of the tinting-strength method to other agreed criteria, including a reference to ISO 18314-2.
The revision also moves former notes into the main text in Clause 5, updates the table headers, revises several material requirements in Clause 5, adds ISO 9277 for the fumed silica test method, allows other light sources for the tristimulus colorimeter, adds a reference for measuring paste films on a moving carrier without contact, and adds a bibliography.
Which standards are used with SIST EN ISO 787-24:2026?
| Standard | What it contributes |
|---|---|
| ISO 591-1 | Specification and test methods for titanium dioxide pigment used in the white pigment paste |
| ISO 787-2 | Test method for matter volatile at 105 °C |
| ISO 787-9 | Test method for pH value of an aqueous suspension |
| ISO 787-10 | Density by pyknometer, used for white pigment mass calculation |
| ISO 787-16 | Visual comparison method for relative tinting strength and colour on reduction |
| ISO 787-17 | Visual comparison method for lightening power of white pigments |
| ISO 787-23 | Density by centrifuge removal of entrained air |
| ISO 1524 | Fineness of grind of the paste |
| ISO 3219 (all parts) | Viscosity of the alkyd resin |
| ISO 2114 | Acid value of the alkyd resin |
| ISO 4629 (all parts) | Hydroxyl value of the alkyd resin |
| ISO 4652 | Specific surface area of carbon black by nitrogen adsorption |
| ISO 6209 | Solvent-extractable material in carbon black |
| ISO 9277 | BET specific surface area for fumed silica |
| ISO 15528 | Sampling of paints, varnishes and raw materials |
| ISO 18314-3 | Blackness value M_Y for carbon black pigment |
| ISO 18314-2 | Alternative tinting-strength criteria and Saunderson correction |
What does the SIST EN ISO 787-24:2026 document contain?
SIST EN ISO 787-24:2026 contains the full laboratory method, not just the result definitions. It includes the composition and preparation of the white pigment paste and black pigment paste, the requirements for the alkyd resin and auxiliary materials, and the equipment needed for grinding and measurement.
The document also gives step-by-step procedures for preparing dispersions, making test films, and measuring ϱ or R for both coloured and white pigments. Annex A supports the conversion between reflectivity and K/S, and Annex B provides the table used to read K/S values from measured reflectance data.
Clause 10 sets out the information that must be recorded in the test report, so the document can be used for routine quality control, inter-laboratory comparison, supplier qualification, and other technical decisions where traceable pigment comparison is needed.
Relations
- Effective Date
- 01-Dec-2026
- Effective Date
- 28-Oct-2026
Frequently Asked Questions
SIST EN ISO 787-24:2026 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "General methods of test for pigments and extenders - Part 24: Photometric methods for determining the relative tinting strength of coloured pigments and the relative scattering power of white pigments (ISO 787-24:2026)". This standard covers: This document specifies photometric methods of test for comparing in the visible spectrum: a) the tinting strength of two similar coloured pigments dispersed in an alkyd resin without a drier; b) the scattering power of two white pigments of the same type dispersed in an alkyd resin without a drier. This document does not apply to the comparison of coloured pigments that on reduction differ greatly in colour.
This document specifies photometric methods of test for comparing in the visible spectrum: a) the tinting strength of two similar coloured pigments dispersed in an alkyd resin without a drier; b) the scattering power of two white pigments of the same type dispersed in an alkyd resin without a drier. This document does not apply to the comparison of coloured pigments that on reduction differ greatly in colour.
SIST EN ISO 787-24:2026 is classified under the following ICS (International Classification for Standards) categories: 87.060.10 - Pigments and extenders. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN ISO 787-24:2026 has the following relationships with other standards: It is inter standard links to SIST EN ISO 787-24:1997, SIST EN 14469-3:2004. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN ISO 787-24:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2026
Nadomešča:
SIST EN ISO 787-24:1997
Splošne preskusne metode za pigmente in polnila - 24. del: Fotometrijske metode
za določanje relativne barvne jakosti barvnih pigmentov in relativne moči sipanja
belih pigmentov (ISO 787-24:2026)
General methods of test for pigments and extenders - Part 24: Photometric methods for
determining the relative tinting strength of coloured pigments and the relative scattering
power of white pigments (ISO 787-24:2026)
Allgemeine Prüfverfahren für Pigmente und Füllstoffe - Teil 24: Photometrische
Verfahren zur Bestimmung der relativen Farbstärke von Buntpigmenten und des
relativen Streuvermögens von Weißpigmenten (ISO 787-24:2026)
Méthodes générales d’essai des pigments et matières de charge - Partie 24: Méthodes
photométriques pour la détermination du pouvoir colorant relatif des pigments colorés et
du pouvoir diffusant relatif des pigments blancs (ISO 787-24:2026)
Ta slovenski standard je istoveten z: EN ISO 787-24:2026
ICS:
87.060.10 Pigmenti in polnila Pigments and extenders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 787-24
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2026
EUROPÄISCHE NORM
ICS 87.060.10 Supersedes EN ISO 787-24:1995
English Version
General methods of test for pigments and extenders - Part
24: Photometric methods for determining the relative
tinting strength of coloured pigments and the relative
scattering power of white pigments (ISO 787-24:2026)
Méthodes générales d'essai des pigments et matières Allgemeine Prüfverfahren für Pigmente und Füllstoffe -
de charge - Partie 24: Méthodes photométriques pour Teil 24: Photometrische Verfahren zur Bestimmung
la détermination du pouvoir colorant relatif des der relativen Farbstärke von Buntpigmenten und des
pigments colorés et du pouvoir diffusant relatif des relativen Streuvermögens von Weißpigmenten (ISO
pigments blancs (ISO 787-24:2026) 787-24:2026)
This European Standard was approved by CEN on 21 September 2026.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 787-24:2026 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 787-24:2026) has been prepared by Technical Committee ISO/TC 256
"Pigments, dyestuffs and extenders" in collaboration with Technical Committee CEN/TC 298 “Pigments
and extenders” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2027, and conflicting national standards shall be
withdrawn at the latest by April 2027.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 787-24:1995.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 787-24:2026 has been approved by CEN as EN ISO 787-24:2026 without any
modification.
International
Standard
ISO 787-24
Third edition
General methods of test for
2026-10
pigments and extenders —
Part 24:
Photometric methods for
determining the relative tinting
strength of coloured pigments and
the relative scattering power of
white pigments
Méthodes générales d’essai des pigments et matières de charge —
Partie 24: Méthodes photométriques pour la détermination
du pouvoir colorant relatif des pigments colorés et du pouvoir
diffusant relatif des pigments blancs
Reference number
ISO 787-24:2026(en) © ISO 2026
ISO 787-24:2026(en)
© ISO 2026
All rights reserved.
This ISO publication is protected by copyright and is owned by ISO and/or its licensors.
The content of this ISO publication is provided under licence, not sold. Use is subject to the applicable licence terms issued by ISO,
an ISO member body, or an authorized third-party distributor.
Except as required for implementation or expressly permitted by a separate licence, no part of this ISO publication may be
reproduced, distributed, modified, used, or made available in any form or by any means – electronic or mechanical, including
photocopying, scanning, recording, or posting on internal or external digital platforms.
Any use beyond the scope of the granted rights is prohibited and may result in legal action.
ISO copyright office
CP 401 • CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 787-24:2026(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
3.1 Terms related to coloured and black pigments .2
3.2 Terms related to white pigments .2
3.3 Terms related to reflectivity .3
3.4 Terms related to reflectance factor .3
4 Principle . 3
4.1 General .3
4.2 Coloured and black pigments .3
4.3 White pigments . .4
5 Materials and equipment . 4
6 Apparatus . 5
7 Sampling . 6
8 Procedure . 6
8.1 Determination of relative tinting strength .6
8.1.1 Test pigment dispersion . .6
8.1.2 Reference pigment dispersion .7
8.1.3 Preparation of test films .7
8.1.4 Measurement of ϱ or R .7
∞ ∞
8.2 Determination of relative scattering power .7
8.2.1 General .7
8.2.2 Test pigment dispersion . .7
8.2.3 Reference pigment dispersion .8
8.2.4 Preparation of test films .8
8.2.5 Measurement of ϱ or R .8
∞ ∞
9 Expression of results . 8
10 Test report . 8
Annex A (informative) Reflectivity and Kubelka-Munk analysis .10
Bibliography .11
iii
ISO 787-24:2026(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 256, Pigments, dyestuffs and extenders, in
collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/TC 298,
Pigments and extenders, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 787-24:1985), which has been technically
revised.
The main changes are as follows:
— the introduction has been deleted;
— the normative references have been updated;
— in Clause 3, the definitions have been updated and, where necessary, aligned with ISO 18451-1;
— 3.1.3 “absorbance index” has been changed to “absorption index”;
— 4.1 has been added;
— in 4.2, “K ” has been replaced by “C “ as symbol for relative tinting strength;
r rel
— in 4.2 and 8.1.4, the method has been opened to other tinting strength criterion, including a reference to
ISO 18314-2;
— the characteristic “nigrometer index value” and its requirement have been changed to “blackness value
M ” for the characteristic and to “203 to 215” for the requirement, and ISO 18314-3 has been added as a
Y
test method (Clause 5, Table 2);
2 2
— the requirement for “specific surface area (BET)” has been changed to “25 m /g to 33 m /g” for carbon
black pigment (Clause 5, Table 2);
— the requirement for the pH value has been changed to “6 to 9” for carbon black pigment (Clause 5, Table 2);
iv
ISO 787-24:2026(en)
— ISO 9277 has been added as the test method for the specific surface area (BET) for fumed silica (Clause 5,
Table 3);
— in 6.3, a reference was included which described the possibility of measuring paste films on a moving
carrier without any contact;
— in 6.4, additional light sources for the tristimulus colorimeter were included;
— Annex A has been modified and subdivided into A.1 and A.2;
— Annex B has been deleted;
— a bibliography has been added.
A list of all parts in the ISO 787 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
v
International Standard ISO 787-24:2026(en)
General methods of test for pigments and extenders —
Part 24:
Photometric methods for determining the relative tinting
strength of coloured pigments and the relative scattering
power of white pigments
1 Scope
This document specifies photometric methods of test for comparing in the visible spectrum:
a) the tinting strength of two similar coloured pigments dispersed in an alkyd resin without a drier;
b) the scattering power of two white pigments of the same type dispersed in an alkyd resin without a
drier.
This document does not apply to the comparison of coloured pigments that on reduction differ greatly in
colour.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 591-1, Titanium dioxide pigments for paints — Part 1: Specifications and methods of test
ISO 787-2, General methods of test for pigments and extenders — Part 2: Determination of matter volatile at 105
°C
ISO 787-9, General methods of test for pigments and extenders — Part 9: Determination of pH value of an
aqueous suspension
ISO 787-10, General methods of test for pigments and extenders — Part 10: Determination of density —
Pyknometer method
ISO 3219 (all parts), Rheology
ISO 2114, Plastics (polyester resins) and paints and varnishes (binders) — Determination of partial acid value
and total acid value
ISO 4629 (all parts), Binders for paints and varnishes — Determination of hydroxyl value
ISO 4652, Rubber compounding ingredients — Carbon black — Determination of specific surface area by
nitrogen adsorption methods — Single-point procedures
ISO 6209, Rubber compounding ingredients — Carbon black — Determination of solvent-extractable material
ISO 9277, Determination of the specific surface area of solids by gas adsorption — BET method
ISO 15528, Paints, varnishes and raw materials for paints and varnishes — Sampling
ISO 787-24:2026(en)
ISO 18314-2, Analytical colorimetry — Part 2: Saunderson correction, solutions of the Kubelka-Munk equation,
tinting strength, depth of shade and hiding power
ISO 18314-3, Analytical colorimetry — Part 3: Special indices
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1 Terms related to coloured an
...



