SIST EN 18142:2027
(Main)Self-loading mobile concrete mixers - Safety requirements and verification
- Abstract
This document specifies general safety requirements for self-loading mobile concrete mixers (here-after referred to as "SLMs") as defined in ISO 18650-1:2021, with rigid or articulated wheeled chassis.
This document applies to SLMs which are designed for front or rear loading and can be provided with a slewing and/or tilting frame where the rotating drum and the self-loading equipment (lift arms and bucket) are mounted on. SLMs can also be fitted with accessories such as water dosing means and a weighing system.
This document is not applicable to the following:
- machines designed primarily for earth moving, such as loaders or dumpers (see applicable parts of the EN 474 series);
- truck mixers (see EN 12609).
This document deals with all significant hazards, hazardous situations and events relevant to SLMs, whether used as intended and under conditions foreseen or under conditions of misuse reasonably foreseeable by the manufacturer (see Annex A).
This document does not provide performance levels required for safety related functions of control systems.
NOTE A document providing detailed description of safety functions for SLMs and related performance levels required is under development.
This document does not address hazards that can occur:
- during manufacture;
- when using SLMs on public roads, where specific local road regulations can apply;
- when operating in potentially explosive atmospheres.
This document does not address hazards specifically related to:
- SLMs designed to operate with varying levels of autonomy or when SLMs have embedded safety-systems with fully or partially self-evolving behaviour or logic using machine learning approaches, including collaborative applications;
- SLMs when intended to be connected to the internet or to an external network or device that communicates with it (protection against corruption).
This document is not applicable to SLMs manufactured before the date of its publication.
- Status
- Published
- Public Enquiry End Date
- 09-Jun-2025
- Publication Date
- 17-Nov-2026
- Technical Committee
- I13 - Imaginarni 13
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 16-Nov-2026
- Due Date
- 21-Jan-2027
- Completion Date
- 18-Nov-2026
SIST EN 18142:2027 is the standard for self-loading mobile concrete mixers (SLMs). It sets general safety requirements and verification methods for SLMs with rigid or articulated wheeled chassis, including machines designed for front or rear loading and fitted with a rotating drum, lift arms and bucket. It is written for manufacturers, safety bodies, users and service providers who need to design, check, buy or maintain these machines.
What does SIST EN 18142:2027 specify?
SIST EN 18142:2027 specifies the safety requirements for SLMs as defined in ISO 18650-1:2021, and it covers significant hazards during intended use and reasonably foreseeable misuse. It applies to machines with optional features such as a slewing or tilting frame, water dosing means and a weighing system.
The standard excludes machines designed mainly for earth moving, such as loaders and dumpers, and truck mixers. It also leaves out hazards linked to manufacture, use on public roads, explosive atmospheres, autonomous or machine-learning-based safety behavior, and connection to the internet or another external network or device.
The document is organized into:
- Clause 4 - safety requirements and protective measures
- Clause 5 - verification methods
- Clause 6 - information for use and marking
- Annex A - list of significant hazards
- Annex ZA - link to Regulation (EU) 2023/1230
| Annex | What it covers |
|---|---|
| Annex A | Significant hazards, hazardous situations and hazardous events covered by the standard |
| Annex ZA | Relationship between the standard and the essential requirements of Regulation (EU) 2023/1230 |
What are the key requirements of SIST EN 18142:2027?
SIST EN 18142:2027 is built around practical risk reduction on the whole machine - access, operator protection, controls, mobility, systems, the rotating drum and maintenance. Clause 4 also says the machine shall follow EN ISO 12100 for relevant hazards that are not specifically covered here.
Access, cab and operator station
Clauses 4.2 and 4.3 require safe access to the operator’s station and routine maintenance points, and access systems shall comply with EN ISO 2867. For articulated SLMs, the access path needs enough clearance in the fully articulated steering position, so operators can reach the station without interference from moving parts.
The operator’s station must provide the space and layout needed for safe control, with room for instructions if paper manuals are used. SLMs other than compact SLMs need provisions for an enclosed cab, and the cab must protect the operator from weather, allow ventilation, heating and defrosting, and provide a clear emergency exit.
Seats, restraints and controls
Clause 4.4 requires an adjustable seat that keeps the operator in a position suitable for controlling the machine. The seat must meet the dimensional and vibration-related requirements referenced in the standard, and the restraint system must prevent powered travel if the operator is not fastened in the driving position.
Clause 4.5 controls how levers, joysticks, pedals and switches are arranged and marked. It also requires safe start-up behavior, return-to-neutral behavior where needed, protection against inadvertent activation, and emergency lowering of the loading equipment if normal controls fail. In practice, this means the controls must behave predictably and the operator must always be able to stop or recover the machine safely.
Steering, braking, visibility and stability
Clauses 4.6 to 4.12 cover steering, brakes, visibility, warning devices, tyres, stability and noise. The steering control movement must match the intended direction, the machine needs service, secondary and parking brakes, and the operator must have sufficient visibility for travel and work areas.
The standard also requires an audible horn, lighting and reflectors, and noise measurement under defined operating conditions. Stability has to be maintained in intended use, including maintenance and transport, and devices that improve stability must stay in position if hoses fail or oil leaks.
Guards, systems and transport
Clauses 4.13 to 4.19 address hot parts, moving parts, guards, articulated frame lock, fenders, retrieval, lifting, towing, EMC, electrical systems, hydraulics, tanks and fire protection. The machine must protect against crushing, shearing, cutting and entanglement, and guarded parts must remain safe during access and maintenance.
Electrical and hydraulic systems need protection against damage, incorrect connection and environmental exposure. Fuel tanks, hydraulic tanks, pressure vessels and battery arrangements must be designed to limit leakage, fire and overturn risks, and compact SLMs get some specific exceptions, such as for the fire extinguisher space.
Rotating drum, maintenance and special operating cases
Clauses 4.20 to 4.23 focus on the rotating drum and loading equipment, routine maintenance, underground use in non-explosive atmospheres, and safety functions. The drum and rollers must be guarded so they do not create exposure during rotation, and the loading equipment must not lower unexpectedly.
Maintenance provisions are extensive: safe access, support devices, secured openings and clear procedures for cleaning and servicing. For underground work, the standard adds lighting, fuel, exhaust and fire-related requirements. Clause 4.23 requires safety functions to be testable and assessed using EN ISO 13849-1 or EN ISO 19014-1, which is important because the standard refers to safety-related control behavior but does not set separate performance levels for it.
What terms does SIST EN 18142:2027 define?
- SLM - a self-loading mobile concrete mixer, the machine type covered by the standard.
- Self-loading equipment - the bucket-supporting structure and linkage that lets the SLM load its own drum.
- Rated capacity - the manufacturer-declared concrete output per cycle under the specified operating conditions.
- Operating mass - the machine mass in ready-to-run condition, including the operator, fuel and fluids, with the drum and self-loading equipment empty.
- Compact SLM - the smaller-capacity SLM category used in the standard for some reduced requirements.
- Operator’s station - the area from which the operator controls some or all SLM functions.
- ROPS - roll-over protective structure, the protective structure required to protect the operator in a rollover.
- FOPS - falling-object protective structure, the protective structure required against falling objects.
Who uses SIST EN 18142:2027?
SIST EN 18142:2027 is mainly used by machine manufacturers, including small, medium and large enterprises, when designing or adapting SLMs. It is also used by regulators, market surveillance bodies and accident-prevention organizations when checking whether a machine design addresses the expected hazards.
Users and employers use it to understand what safety features, instructions and markings they should expect from an SLM. Service providers use it when planning maintenance access, safe support devices, drum cleaning and other service tasks.
Which standards are used with SIST EN 18142:2027?
| Standard | What it contributes |
|---|---|
| EN ISO 12100:2010 | General risk assessment and risk reduction principles, plus instructions for use |
| ISO 18650-1:2021 | Definition of the SLM product family |
| EN ISO 2867:2011 | Access systems and opening dimensions |
| EN ISO 3471:2008 | ROPS test and performance requirements |
| EN ISO 3449:2008 | FOPS performance level |
| EN ISO 3450:2011 | Brake system requirements and test procedures |
| EN ISO 7096:2020 | Operator seat vibration performance |
| EN ISO 5010:2019 | Steering requirements for wheeled machines |
| EN ISO 13766-1:2018 and EN ISO 13766-2:2018 | EMC requirements, including functional safety aspects |
| EN 60204-1:2018 | General electrical equipment requirements |
| EN ISO 4413:2010 | Hydraulic system safety requirements |
| ISO 6750-1:2019 | Operator’s manual content and format |
| ISO 9244:2008 | Safety labels |
| ISO 5006:2017 | Operator field-of-view test method and criteria |
| ISO 10968:2020 | Control design and arrangement |
| ISO 15817:2012 | Remote operator control systems |
| ISO 15818:2017 | Lifting and tying-down attachment points |
| EN 474 series | Reference point for earth-moving machinery excluded from scope |
| EN 12609 | Reference point for truck mixers excluded from scope |
| EN 206:2013+A2:2021 | Slump class S1 and concrete-related capacity definition |
| EN ISO 13849-1:2023 or EN ISO 19014-1:2018 | Assessment of safety-related parts of control systems |
What does the SIST EN 18142:2027 document contain?
SIST EN 18142:2027 contains detailed technical requirements for the machine structure, cab, seat, controls, steering, braking, visibility, guarding, hydraulics, electrical systems, fuel systems, fire protection, drum safety, maintenance access and underground operation. It also includes specific clauses for safety functions and how they are to be checked.
Clause 5 links each requirement to one or more verification methods - calculation, visual verification, measurement, functional test or special verification against another standard. That makes the document usable for design review, prototype testing and conformity assessment.
Clause 6 sets out the information to be supplied with the machine, including safety labels, the operator’s manual, the maintenance manual and marking. Annex A gives the hazard list behind the standard, and Annex ZA maps the clauses to Regulation (EU) 2023/1230.
Get Certified
Connect with accredited certification bodies for this standard

DIBt (Deutsches Institut für Bautechnik)
German Institute for Building Technology.
DIN CERTCO
DIN Group product certification.

Aboma Certification B.V.
Specialized in construction, metal, and transport sectors.
Sponsored listings
Frequently Asked Questions
SIST EN 18142:2027 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Self-loading mobile concrete mixers - Safety requirements and verification". This standard covers: This document specifies general safety requirements for self-loading mobile concrete mixers (here-after referred to as "SLMs") as defined in ISO 18650-1:2021, with rigid or articulated wheeled chassis. This document applies to SLMs which are designed for front or rear loading and can be provided with a slewing and/or tilting frame where the rotating drum and the self-loading equipment (lift arms and bucket) are mounted on. SLMs can also be fitted with accessories such as water dosing means and a weighing system. This document is not applicable to the following: - machines designed primarily for earth moving, such as loaders or dumpers (see applicable parts of the EN 474 series); - truck mixers (see EN 12609). This document deals with all significant hazards, hazardous situations and events relevant to SLMs, whether used as intended and under conditions foreseen or under conditions of misuse reasonably foreseeable by the manufacturer (see Annex A). This document does not provide performance levels required for safety related functions of control systems. NOTE A document providing detailed description of safety functions for SLMs and related performance levels required is under development. This document does not address hazards that can occur: - during manufacture; - when using SLMs on public roads, where specific local road regulations can apply; - when operating in potentially explosive atmospheres. This document does not address hazards specifically related to: - SLMs designed to operate with varying levels of autonomy or when SLMs have embedded safety-systems with fully or partially self-evolving behaviour or logic using machine learning approaches, including collaborative applications; - SLMs when intended to be connected to the internet or to an external network or device that communicates with it (protection against corruption). This document is not applicable to SLMs manufactured before the date of its publication.
This document specifies general safety requirements for self-loading mobile concrete mixers (here-after referred to as "SLMs") as defined in ISO 18650-1:2021, with rigid or articulated wheeled chassis. This document applies to SLMs which are designed for front or rear loading and can be provided with a slewing and/or tilting frame where the rotating drum and the self-loading equipment (lift arms and bucket) are mounted on. SLMs can also be fitted with accessories such as water dosing means and a weighing system. This document is not applicable to the following: - machines designed primarily for earth moving, such as loaders or dumpers (see applicable parts of the EN 474 series); - truck mixers (see EN 12609). This document deals with all significant hazards, hazardous situations and events relevant to SLMs, whether used as intended and under conditions foreseen or under conditions of misuse reasonably foreseeable by the manufacturer (see Annex A). This document does not provide performance levels required for safety related functions of control systems. NOTE A document providing detailed description of safety functions for SLMs and related performance levels required is under development. This document does not address hazards that can occur: - during manufacture; - when using SLMs on public roads, where specific local road regulations can apply; - when operating in potentially explosive atmospheres. This document does not address hazards specifically related to: - SLMs designed to operate with varying levels of autonomy or when SLMs have embedded safety-systems with fully or partially self-evolving behaviour or logic using machine learning approaches, including collaborative applications; - SLMs when intended to be connected to the internet or to an external network or device that communicates with it (protection against corruption). This document is not applicable to SLMs manufactured before the date of its publication.
SIST EN 18142:2027 is classified under the following ICS (International Classification for Standards) categories: 91.220 - Construction equipment. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 18142:2027 is associated with the following European legislation: EU Directives/Regulations: 2006/42/EC, 2023/1230; Standardization Mandates: M/396, M/605. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
SIST EN 18142:2027 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2027
Samonakladalni mobilni mešalniki za beton - Varnostne zahteve in preverjanje
Self-loading mobile concrete mixers - Safety requirements and verification
Selbstladende mobile Betonmischer - Sicherheitsanforderungen und Überprüfung
Malaxeurs à béton mobiles avec autochargeur - Exigences de sécurité et vérification
Ta slovenski standard je istoveten z: EN 18142:2026
ICS:
91.220 Gradbena oprema Construction equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 18142
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2026
EUROPÄISCHE NORM
ICS 91.220
English Version
Self-loading mobile concrete mixers - Safety requirements
and verification
Malaxeurs à béton mobiles avec autochargeur - Selbstladende mobile Betonmischer -
Exigences de sécurité et vérification Sicherheitsanforderungen und Überprüfung
This European Standard was approved by CEN on 28 September 2026.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 18142:2026 E
worldwide for CEN national Members.
Contents Page
European foreword . 5
Introduction . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 11
4 Safety requirements and/or protective/risk reduction measures . 12
4.1 General. 12
4.2 Access systems . 12
4.2.1 General requirements . 12
4.2.2 Access to articulated SLMs . 12
4.3 Operator’s station on the SLM . 13
4.3.1 General requirements . 13
4.3.2 Operator’s station equipped with a cab . 13
4.3.3 Operator-protective structures . 15
4.4 Operator’s seat . 15
4.4.1 General requirements . 15
4.4.2 Dimensions. 15
4.4.3 Adjustment . 15
4.4.4 Vibration . 16
4.4.5 Restraint system . 16
4.5 Operator’s controls and indicators . 16
4.5.1 General. 16
4.5.2 Engine start . 16
4.5.3 Controls activation . 16
4.5.4 Inadvertent activation . 17
4.5.5 Pedals . 17
4.5.6 Emergency loading equipment lowering . 17
4.5.7 Uncontrolled motion . 17
4.5.8 Multiple operating positions . 17
4.5.9 Reversible operating position . 17
4.5.10 Visual displays, control panels, indicators and symbols . 17
4.6 Steering systems . 18
4.6.1 General. 18
4.6.2 Wheeled SLMs . 18
4.7 Brake systems . 18
4.8 Visibility . 18
4.8.1 Operator’s field of view . 18
4.8.2 Lighting, signalling and marking lights, and reflex-reflector devices . 19
4.9 Warning devices . 19
4.10 Tyres and rims . 19
4.11 Stability . 19
4.12 Noise . 20
4.12.1 Requirements for noise reduction. 20
4.12.2 Noise emission measurement . 20
4.13 Protective measures and devices . 21
4.13.1 Hot parts . 21
4.13.2 Moving parts . 21
4.13.3 Guards . 21
4.13.4 Articulated frame lock . 21
4.13.5 Sharp edges and acute angles. 21
4.13.6 Fenders . 21
4.14 Retrieval, transportation, lifting and towing . 22
4.14.1 Common use . 22
4.14.2 Retrieval . 22
4.14.3 Tying-down . 22
4.14.4 Lifting . 22
4.14.5 Off-road towing . 22
4.14.6 Transportation . 22
4.15 Electromagnetic compatibility . 22
4.16 Electrical and electronic systems . 22
4.16.1 General . 22
4.16.2 Degree of protection . 23
4.16.3 Electrical connections . 23
4.16.4 Over-current protective devices . 23
4.16.5 Batteries . 23
4.16.6 Battery disconnection . 23
4.16.7 Electrical connectors for auxiliary starting aids . 24
4.16.8 Electric sockets for lighting. 24
4.17 Hydraulic systems . 24
4.17.1 General requirements . 24
4.17.2 Hydraulic lines . 24
4.17.3 Hydraulic hose assemblies . 24
4.18 Fuel tanks, DEF/urea tanks, hydraulic tanks and pressure vessels . 24
4.18.1 General . 24
4.18.2 Filler openings . 24
4.18.3 Fuel tanks . 25
4.18.4 Simple pressure vessels . 25
4.19 Fire protection . 25
4.19.1 Fire resistance . 25
4.19.2 Fire extinguisher . 25
4.20 Rotating drum and related equipment . 25
4.20.1 Rotating drum . 25
4.20.2 Rollers . 25
4.20.3 Loading equipment . 25
4.20.4 Discharging chute . 26
4.20.5 Cleaning system . 26
4.21 Maintenance . 26
4.21.1 General . 26
4.21.2 Routine maintenance . 26
4.21.3 Support devices . 27
4.21.4 Access to the engine compartment . 27
4.22 Underground operation in non-explosive atmospheres . 27
4.22.1 General . 27
4.22.2 Lighting, signalling and marking lights, and reflex-reflector devices . 27
4.22.3 Engine exhaust emission and fuel . 27
4.23 Safety functions . 28
5 Verification of safety requirements and/or protective/risk reduction measure . 30
6 Information for use . 34
6.1 General. 34
6.2 Safety labels . 34
6.3 Operator’s manual . 34
6.3.1 General. 34
6.3.2 Information concerning airborne noise emission . 35
6.3.3 Information concerning hand-arm and whole-body vibration emission . 36
6.3.4 Information concerning the rotating drum and materials related to the work cycle . 37
6.4 Maintenance manual . 37
6.5 Marking . 38
Annex A (informative) List of significant hazards . 39
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Regulation (EU) 2023/1230 aimed to be covered . 47
Bibliography . 51
European foreword
This document (EN 18142:2026) has been prepared by Technical Committee CEN/TC 151 “Construction
equipment and building material machines - Safety”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2027 and conflicting national standards shall be withdrawn at
the latest by May 2027.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this
document.
Any feedback and questions on this document should be directed to the users’ national standards body. A
complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
Introduction
This document is a type-C standard as stated in EN ISO 12100.
This document is of relevance, in particular, for the following stakeholder groups representing the market
players with regard to machinery safety:
— machine manufacturers (small, medium and large enterprises);
— health and safety bodies (regulators, accident prevention organizations, market surveillance, etc.).
Others can be affected by the level of machinery safety achieved with the means of the document by the
above-mentioned stakeholder groups:
— machine users/employers (small, medium and large enterprises);
— machine users/employees (e.g. trade unions, organizations for people with special needs);
— service providers, e.g. for maintenance (small, medium and large enterprises);
— consumers (in the case of machinery intended for use by consumers).
The above-mentioned stakeholder groups have been given the possibility to participate at the drafting
process of this document.
The machinery concerned and the extent to which hazards, hazardous situations or hazardous events are
covered are indicated in the Scope of this document.
When requirements of this type-C standard are different from those which are stated in type-A or type-B
standards, the requirements of this type-C standard take precedence over the requirements of the other
standards for machines that have been designed and built according to the requirements of this type-C
standard.
1 Scope
This document specifies general safety requirements for self-loading mobile concrete mixers (here-after
referred to as “SLMs”) as defined in ISO 18650-1:2021, with rigid or articulated wheeled chassis.
This document applies to SLMs which are designed for front or rear loading and can be provided with a
slewing and/or tilting frame where the rotating drum and the self-loading equipment (lift arms and bucket)
are mounted on. SLMs can also be fitted with accessories such as water dosing means and a weighing
system.
This document is not applicable to the following:
— machines designed primarily for earth moving, such as loaders or dumpers (see applicable parts of the
EN 474 series);
— truck mixers (see EN 12609).
This document deals with all significant hazards, hazardous situations and events relevant to SLMs,
whether used as intended and under conditions foreseen or under conditions of misuse reasonably
foreseeable by the manufacturer (see Annex A).
This document does not provide performance levels required for safety related functions of control
systems.
NOTE A document providing detailed description of safety functions for SLMs and related performance levels
required is under development.
This document does not address hazards that can occur:
— during manufacture;
— when using SLMs on public roads, where specific local road regulations can apply;
— when operating in potentially explosive atmospheres.
This document does not address hazards specifically related to:
— SLMs designed to operate with varying levels of autonomy or when SLMs have embedded safety-
systems with fully or partially self-evolving behaviour or logic using machine learning approaches,
including collaborative applications;
— SLMs when intended to be connected to the internet or to an external network or device that
communicates with it (protection against corruption).
This document is not applicable to SLMs manufactured before the date of its publication.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
EN 1032:2003+A1:2008, Mechanical vibration — Testing of mobile machinery in order to determine the
vibration emission value
EN 60204-1:2018, Safety of machinery — Electrical equipment of machines — Part 1: General requirements
As impacted by EN 60204-1:2018/A1:2025.
EN 60529:1991, Degrees of protection provided by enclosures (IP Code) (IEC 60529:1989)
EN ISO 2860:2008, Earth-moving machinery — Minimum access dimensions (ISO 2860:1992)
EN ISO 2867:2011, Earth-moving machinery — Access systems (ISO 2867:2011)
EN ISO 3164:2013, Earth-moving machinery — Laboratory evaluations of protective structures —
Specifications for deflection-limiting volume
EN ISO 3411:2007, Earth-moving machinery — Physical dimensions of operators and minimum operator
space envelope (ISO 3411:2007)
EN ISO 3449:2008, Earth-moving machinery — Falling-object protective structures — Laboratory tests and
performance requirements (ISO 3449:2005)
EN ISO 3450:2011, Earth-moving machinery — Wheeled or high-speed rubber-tracked machines —
Performance requirements and test procedures for brake systems (ISO 3450:2011)
EN ISO 3457:2008, Earth-moving machinery — Guards — Definitions and requirements (ISO 3457:2003)
EN ISO 3471:2008, Earth-moving machinery — Roll-over protective structures — Laboratory tests and
performance requirements (ISO 3471:2008)
EN ISO 3744:2026, Acoustics — Determination of sound power levels of noise sources using sound pressure —
Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2025, including corrected
version 2026-01)
EN ISO 4413:2010, Hydraulic fluid power — General rules and safety requirements for systems and their
components (ISO 4413:2010)
EN ISO 4871:2009, Acoustics — Declaration and verification of noise emission values of machinery and
equipment (ISO 4871:1996)
EN ISO 5010:2019, Earth-moving machinery — Wheeled machines — Steering requirements (ISO
5010:2019)
EN ISO 6682:2008, Earth-moving machinery — Zones of comfort and reach for controls (ISO 6682:1986,
including Amd 1:1989)
EN ISO 6683:2025, Earth-moving machinery — Seat-belt assemblies and seat-belt anchorages —
Performance requirements and tests (ISO 6683:2025)
EN ISO 7096:2020, Earth-moving machinery — Laboratory evaluation of operator seat vibration (ISO
7096:2020)
EN ISO 11201:2010, Acoustics — Noise emitted by machinery and equipment — Determination of emission
sound pressure levels at a work station and at other specified positions in an essentially free field over a
reflecting plane with negligible environmental corrections (ISO 11201:2010)
EN ISO 12100:2010, Safety of machinery — General principles for design — Risk assessment and risk
reduction (ISO 12100:2010)
As impacted by EN 60529:1991/A1:2000, EN 60529:1991/A2:2013, EN 60529:1991/AC:2016-12,
EN 60529:1991/corrigendum May 1993 and EN 60529:1991/A2:2013/AC:2019-02.
As impacted by EN ISO 3164:2013/A1:2024.
EN ISO 13766-1:2018, Earth-moving and building construction machinery — Electromagnetic compatibility
(EMC) of machines with internal electrical power supply — Part 1: General EMC requirements under typical
electromagnetic environmental conditions (ISO 13766-1:2018)
EN ISO 13766-2:2018, Earth-moving and building construction machinery — Electromagnetic compatibility
(EMC) of machines with internal electrical power supply — Part 2: Additional EMC requirements for
functional safety (ISO 13766-2:2018)
EN ISO 13850:2015, Safety of machinery — Emergency stop function — Principles for design (ISO
13850:2015)
EN ISO 13857:2019, Safety of machinery — Safety distances to prevent hazard zones being reached by upper
and lower limbs (ISO 13857:2019)
EN ISO 14119:2025, Safety of machinery - Interlocking devices associated with guards - Principles for design
and selection (ISO 14119:2024)
EN ISO 14120:2015, Safety of machinery — Guards — General requirements for the design and construction
of fixed and movable guards (ISO 14120:2015)
EN ISO 19014-1:2018, Earth-moving machinery — Functional safety — Part 1: Methodology to determine
safety-related parts of the control system and performance requirements (ISO 19014-1:2018, Corrected
version 2019-02)
EN ISO 19014-2:2022, Earth-moving machinery — Functional safety — Part 2: Design and evaluation of
hardware and architecture requirements for safety-related parts of the control system (ISO 19014-2:2022)
ISO 3776-1:2006, Tractors and machinery for agriculture — Seat belts — Part 1: Anchorage location
requirements
ISO 3776-2:2013, Tractors and machinery for agriculture — Seat belts — Part 2: Anchorage strength
requirements
ISO 3776-3:2009, Tractors and machinery for agriculture — Seat belts — Part 3: Requirements for assemblies
ISO 3795:1989, Road vehicles, and tractors and machinery for agriculture and forestry — Determination of
burning behaviour of interior materials
ISO 5006:2017, Earth-moving machinery — Operator’s field of view — Test method and performance criteria
ISO 6011:2023, Earth-moving machinery — Visual display of machine operation
ISO 6750-1:2019, Earth-moving machinery — Operator’s manual — Part 1: Contents and format
ISO 7000:2019, Graphical symbols for use on equipment — Registered symbols
ISO 9244:2008, Earth-moving machinery — Machine safety labels — General principles
ISO 9533:2010, Earth-moving machinery — Machine-mounted audible travel alarms and forward horns —
Test methods and performance criteria
As impacted by ISO 9244:2008/Amd 1:2016.
ISO 10263-3:2009, Earth-moving machinery — Operator enclosure environment — Part 3: Pressurization
test method
ISO 10263-4:2009, Earth-moving machinery — Operator enclosure environment — Part 4: Heating,
ventilating and air conditioning (HVAC) test method and performance
ISO 10264:1990, Earth-moving machinery — Key-locked starting systems
ISO 10532:1995, Earth-moving machinery — Machine-mounted retrieval device — Performance
requirements
ISO 10533:1993, Earth-moving machinery — Lift-arm support devices
ISO 10570:2004, Earth-moving machinery — Articulated frame lock — Performance requirements
ISO 10968:2020, Earth-moving machinery — Operator’s controls
ISO 11112:1995, Earth-moving machinery — Operator’s seat — Dimensions and requirements
ISO 11862:1993, Earth-moving machinery — Auxiliary starting aid electrical connector
ISO 12508:1994, Earth-moving machinery — Operator station and maintenance areas — Bluntness of edges
ISO 12509:2023, Earth-moving machinery and rough-terrain trucks — Lighting, signalling and marking
lights, and reflex reflectors
ISO 14990-1:2016, Earth-moving machinery — Electrical safety of machines utilizing electric drives and
related components and systems — Part 1: General requirements
ISO 14990-2:2016, Earth-moving machinery — Electrical safety of machines utilizing electric drives and
related components and systems — Part 2: Particular requirements for externally-powered machines
ISO 14990-3:2016, Earth-moving machinery — Electrical safety of machines utilizing electric drives and
related components and systems — Part 3: Particular requirements for self-powered machines
ISO 15817:2012, Earth-moving machinery — Safety requirements for remote operator control systems
ISO 15818:2017, Earth-moving machinery — Lifting and tying-down attachment points — Performance
requirements
ISO 21507:2010, Earth-moving machinery — Performance requirements for non-metallic fuel tanks
As impacted by ISO 10532:1995/Amd 1:2004 and ISO 10532:1995/Cor 1:2006.
As impacted by ISO 10533:1993/Amd 1:2005.
As impacted by ISO 11112:1995/Amd 1:2001.
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN ISO 12100:2010 and the following
apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/
— IEC Electropedia: available at https://www.electropedia.org/
3.1
self-loading equipment
integral mounted bucket-supporting structure and linkage permanently fitted to the SLM, enabling it to fill
its own rotating drum with material
3.2
rated capacity
volume in cubic metres of ready concrete, produced per each cycle, declared by the manufacturer, in
working conditions on flat ground with slump class S1 according to EN 206:2013+A2:2021, measured in
non-vibrated formwork
3.3
operating mass
mass of the SLM, with rotating drum and self-loading equipment (3.1) empty, and with the operator (75 kg),
full fuel tank and all fluid systems (i.e. hydraulic oil, transmission oil, engine oil, engine coolant) at the levels
specified by the manufacturer and with empty water tank(s)
3.4
Compact SLM
SLM with a rated capacity less than 2,5 m
3.5
operator’s station(s)
area from which the operator can control all or specific SLM functions
3.5.1
operator’s station on the SLM
operator's station located on the SLM from which the seated operator can control at least the travelling
function
3.5.2
operator’s station on the ground
operator's station located on the SLM from which the operator standing on the ground can control specific
SLM functions other than the travelling function
3.6
operator’s manual
document that identifies SLM covered and containing information describing and illustrating the safe
operation, maintenance, and safety precautions applicable to the machine and addressed to the operator
Note 1 to entry: This is correlating to the term Instruction handbook used in EN ISO 12100:2010.
[SOURCE: ISO 6750-1:2019, 3.13, modified — Added "and addressed to the operator".]
3.7
maintenance manual
document that identifies SLM covered and containing information describing and illustrating the safe
maintenance, and safety precautions applicable to the SLM and not addressed to the operator
3.8
reusable fitting
hose fitting that is so designed that it can be disassembled from a hose assembly and reassembled to
another hose assembly without losing its function
[SOURCE: ISO 8330:2022, 3.6.3.6]
3.9
crab steering mode
steering mode where all wheels of the SLM steer in the same direction
4 Safety requirements and/or protective/risk reduction measures
4.1 General
SLMs shall comply with the safety requirements and/or protective/risk reduction measures of this clause.
In addition, the SLM shall be designed according to the principles of EN ISO 12100:2010 for relevant but
not significant hazards which are not dealt with by this document.
4.2 Access systems
4.2.1 General requirements
Access systems shall be provided to the operator’s station on the SLM and to routine maintenance points.
Access systems shall conform to EN ISO 2867:2011.
4.2.2 Access to articulated SLMs
On SLMs with articulated frames and in the fully articulated steering position, a minimum clearance of
150 mm shall be provided between firm structures and components with relative movement in the path of
the access systems to the operator’s station on the SLM, as illustrated in Figure 1.
Dimensions in millimetres
Figure 1 — Minimum clearance for access to operator’s station on the SLM with articulated frame
4.3 Operator’s station on the SLM
4.3.1 General requirements
4.3.1.1 Fitting of a cab
SLMs excluding compact SLMs shall have provisions for fitting an enclosed cab.
4.3.1.2 Minimum space
The minimum space available to the operator shall be as defined in EN ISO 3411:2007, with the following
exceptions:
— dimension R as defined in EN ISO 3411:2007, Table 1, may be reduced to a minimum of 920 mm;
— the internal operator's space envelope width from the lower end of upper side walls of enclosure as
defined in EN ISO 3411:2007 may be reduced to a minimum of 650 mm.
The minimum space and location of the controls at the operator’s station shall meet the requirements of
EN ISO 6682:2008.
4.3.1.3 Moving parts
The SLM shall be designed so as to avoid accidental contact from the operating position with moving parts
(e.g. wheels, tracks, working equipment, attachments) in accordance with 4.13.2.
4.3.1.4 Engine exhaust
The engine exhaust system shall release the exhaust gas away from the operator and the air inlet of the cab.
4.3.1.5 Instruction storage
A space intended for operator´s manual safekeeping shall be provided in the cab. If no cab is fitted, the
space shall be provided near the operator’s station.
4.3.1.6 Sharp edges
The operator’s working space within the operator’s station (e.g. ceiling, inner walls, instrument panels,
access to the operator’s station) shall not present any sharp exposed edges or acute angles/corners. The
radius of corners and the bluntness of edges shall conform to ISO 12508:1994, in order to avoid sharp
edges.
4.3.2 Operator’s station equipped with a cab
4.3.2.1 Climatic conditions
The cab shall protect the operator against foreseeable adverse climatic conditions. Provisions shall be made
to install a ventilation system, an adjustable heating system and a system for defrosting windows. For
details, see 4.3.2.5 to 4.3.2.7.
4.3.2.2 Pipes and hoses
Pipes and hoses that contain fluids at pressures exceeding 5 MPa or temperatures above 60 °C located
inside the cab shall be guarded in accordance with EN ISO 3457:2008, Clause 9. See also 4.17.3.
Parts or components placed between pipes or hoses and the operator, which divert a hazardous spray of
fluid, may be considered as a sufficient protection device.
4.3.2.3 Primary opening
A primary access opening shall be provided. The dimensions shall be in accordance with EN ISO 2867:2011.
4.3.2.4 Alternative opening (emergency exit)
An alternative opening shall be provided on a side other than that of the primary opening. The dimensions
shall be in accordance with EN ISO 2867:2011. A window panel or another door is acceptable if they are
easy to open or remove without the use of keys or tools. Latches may be used if they can be opened from
the inside without the use of keys or tools. The breaking of a suitable size of glass pane is considered to
represent a suitable alternative opening, provided that the necessary pane hammer, is provided and stored
in a position accessible to the operator, adjacent to the relevant pane.
The emergency exit shall be marked in accordance with ISO 7010:2019, Table 2, symbol E001 or E002 or
E008 as appropriate.
4.3.2.5 Heating system
A heating system, if fitted, shall be in accordance with ISO 10263-4:2009. If the cab is not equipped with a
pressurization system, then ISO 10263-4:2009, 6.1.1 is not applicable.
4.3.2.6 Ventilation system
The ventilation system shall be capable of providing the cab with fresh air at a minimum of 43 m /h.
4.3.2.7 Defrosting system
A defrosting system shall provide facilities for defrosting the front and rear windows, for example, by
means of a heating system or a particular defrosting device.
NOTE A test method for windscreen defrosting systems is given in ISO 10263-5.
4.3.2.8 Pressurization system
Where a cab is provided with a pressurization system, it shall be tested according to ISO 10263-3:2009 and
shall provide an interior relative pressure of at least 50 Pa.
4.3.2.9 Air conditioning system
Where a cab is provided with an air conditioning system, it shall comply with ISO 10263-4:2009.
4.3.2.10 Doors and windows
Doors, windows and flaps shall be securely held in their intended operating positions. Doors shall be
retained at their intended operating positions by a positive engagement device in accordance with
EN ISO 2867:2011, 5.6.
Windows shall be made of safety glass or other material that provides similar safety performance (see, for
example, ECE R43).
The front window shall be fitted with motorized windscreen wipers and washers.
The rear window shall be fitted with motorized windscreen wipers and washers if direct or indirect
visibility in this direction is required by the visibility requirements in 4.8.
The windscreen washer reservoir/tank shall be accessible in accordance with EN ISO 2867:2011.
4.3.2.11 Interior lighting
The cab shall be fitted with a fixed interior lighting system and shall be able to function with the engine
stopped, so that it is possible to illuminate the operator’s station such that the operator’s manual can be
read in darkness.
4.3.3 Operator-protective structures
4.3.3.1 General
Operator-protective structures shall conform to 4.3.3.2 and 4.3.3.3, except that structural members of the
falling-object protective structure (FOPS) and the roll-over protective structure (ROPS) and the mounts
which attach them to the SLM frame when made from steel shall have one of the following Charpy V- notch
impact strengths (see ISO 148-1 and ISO 148-2):
10 mm × 10 mm specimen: 11 J at −10 °C
10 mm × 7,5 mm specimen: 9,5 J at −10 °C
10 mm × 5 mm specimen: 7,5 J at −10 °C
10 mm × 2,5 mm specimen: 5,5 J at −10 °C
4.3.3.2 Roll-over protective structure (ROPS)
SLMs shall be equipped with a roll-over protective structure (ROPS). The ROPS shall conform to
EN ISO 3471:2008. Table 1 shall be applied to determine the values to be met when testing the ROPS.
Table 1 — Force and energy equations
Lateral load force, Lateral load energy, Vertical load force, Longitudinal load force,
Fl [N] U [J] Fv [N] FL [N]
1,2
1,25
0,66 M+ M MM+ 0,25 M+ M
( )
( )
C
C C
Not applicable
60000 12500
19,61
10000 10000
Key
M SLM operating mass [kg]
M ready-concrete mass [kg]
...



