Abstract

This document specifies methods for determining the change of appearance and stability of textile floor coverings or any damage caused by detachment of layers, opening of joints, cracks, or crazing of resilient, laminate or modular mechanical locked floor coverings under the movement of a swivel castor chair.

Status
Published
Publication Date
19-Nov-2026
Technical Committee
ISO/TC 219 - Floor coverings
Drafting Committee
ISO/TC 219 - Floor coverings
Current Stage
6060 - International Standard published
Start Date
20-Nov-2026
Completion Date
20-Nov-2026

Buy Documents

Standard

ISO 4918:2026 - Resilient, textile, laminate and modular mechanical locked floor coverings — Castor chair test

Release Date:20-Nov-2026
English language (22 pages)
sale 15% off
Preview
sale 15% off
Preview
Standard

ISO 4918:2026 - Revêtement de sol textiles, résilients, stratifiés ou modulaire à verrouillage mécanique — Essai à l'appareil à roulettes

Release Date:20-Nov-2026
French language (22 pages)
sale 15% off
Preview
sale 15% off
Preview

ISO 4918:2026 is an International Standard published by ISO for the castor chair test on resilient, textile, laminate and modular mechanical locked floor coverings. It specifies how to expose flooring specimens to a swivel castor chair and how to judge appearance change, structural damage and stability for manufacturers, test laboratories, specifiers, quality teams and buyers.

What does ISO 4918:2026 specify?

ISO 4918:2026 specifies a test method for assessing how floor coverings behave under repeated swivel castor chair movement. For textile floor coverings, the focus is change in appearance, colour change and structural integrity. For resilient, laminate and modular mechanical locked floor coverings, the focus is visible damage such as layer detachment, joint opening, cracks and crazing.

The standard is organized into clauses on scope, normative references, terms and definitions, principle, apparatus, materials, sampling, conditioning, procedure, assessment, calculations and test report. Annex A is informative and shows an example of sample assembly and clamping. That structure matters because the document combines the test setup, the test run, the inspection method and the reporting rules in one place.

What are the key requirements of ISO 4918:2026?

ISO 4918:2026 requires a rotating test platform with three castors that follow epicyclical paths, multiple changes of direction, stops and starts, and repeated passage over the stressed area. In practice, this creates the type of rolling and turning action that chair wheels apply in use.

Test principle and exposure

The castor assembly is loaded to a total of 90 ± 2 kg, shared equally over the three castors. The platform and castor assembly are mechanically linked, with preset cycling and a reversing action after a defined rotation period. This matters because the load distribution and reversing motion influence whether the floor covering shows wear, cracking, joint opening or delamination.

Apparatus and castors

ISO 4918:2026 defines the main apparatus geometry, including the rotating platform, the offset castor assembly and the test area. It also specifies the castors to be used: Type H castors for textile floor coverings, and Type H or Type W castors for resilient, laminate and modular mechanical locked floor coverings, depending on the relevant product standard or sponsor instruction. The castors must be kept in good condition, cleaned when needed and replaced after a stated service life, because worn wheels can distort the result.

The standard also requires a suction device to keep the surface clear of dust and abraded material during most of the test. For textile floor coverings, the test setup also includes an illumination device for visual assessment. In practice, these controls help keep the inspection repeatable and make damage easier to see.

Sampling and specimen preparation

For textile floor coverings, specimens are taken in accordance with ISO 1957 and prepared separately for Test A, Test B and Test C. The specimens are cut so that their orientation can be compared with the direction of manufacture, and reference specimens are kept for appearance comparison. For resilient floor coverings without a mechanical locking system, the sample must include joints in the castor path. For laminate and modular mechanical locked floor coverings, the test area must include at least one type of each locking variation in the castor path, assembled as the manufacturer instructs.

This sampling approach matters because joint performance and directional effects can affect the result. A product that performs well on a flat, single-piece sample may fail when joints, locking profiles or installation details are included.

Conditioning and mounting

Textile floor coverings are conditioned at 65 ± 4 % relative humidity and 20 ± 2 °C for at least 24 h. Resilient, laminate and modular mechanical locked floor coverings are conditioned at 50 ± 5 % relative humidity and 23 ± 2 °C for at least 24 h. The standard also requires secure mounting so that the specimen cannot shift during testing, while avoiding unnecessary vertical deformation.

For resilient, laminate and modular mechanical locked floor coverings, the specimen is installed with the underlay prescribed by the manufacturer, or the underlay named in the product specification standard if no underlay is prescribed. The assembly must be level, with no centre push-up and with all three castors sharing the load. This matters because uneven support can create false failures or hide real ones.

Textiles: Test A, Test B and Test C

ISO 4918:2026 gives three textile assessment routes. Test A checks appearance retention after 5 000 cycles and 25 000 cycles, and also includes a structural integrity check. Test B checks colour change after 750 cycles. Test C checks structural integrity after 10 000 cycles or 25 000 cycles.

The standard says delamination during testing is recorded, and the affected specimen may fail. Appearance and colour are assessed against ISO 9405 or ASTM D7330, with grey scale comparison for colour change where applicable. In practice, users need to decide whether their interest is visual wear, colour stability or structural breakdown, then choose the corresponding test route.

Resilient, laminate and modular mechanical locked floor coverings: final inspection

For resilient, laminate and modular mechanical locked floor coverings, the specimen is inspected at the end of the test from about 800 mm away and at an approximate 45° angle under defined illumination. The inspection records visible cracks, crazing, detachment of layers and, for mechanical locking systems, opening or ledging of joints. Flattening and gloss change are ignored.

That distinction matters because the standard is looking for damage that affects structure and serviceability, not just superficial appearance change. It is particularly relevant for floating installations and products with locking systems.

Results and reporting

For textile floor coverings, the standard records appearance retention, damage type, colour change and, where applicable, a castor chair index. For the other product groups, the result is the observed damage, if any. The test report also identifies the product, wheel type, adhesive or tape used, mounting method, underlay, deviations, unusual features and test date. This gives users the evidence needed to compare products and document how the test was carried out.

What terms does ISO 4918:2026 define?

  • Crazing - fine random cracks visible on the surface of a floor covering, usually caused by stress on the surface.
  • Delamination - separation of layers in the floor covering, which is one of the main failure modes the test looks for.
  • Appearance retention - the degree to which a textile floor covering keeps its visual appearance after castor chair cycling.
  • Colour change - the visual change in colour assessed by comparison with grey scales after testing.
  • Castor chair index - a calculated value for textile floor coverings, based on the median assessments after 5 000 cycles and 25 000 cycles.
  • Modular mechanical locked floor coverings (MMF) - modular floor covering products with mechanical locking systems, which the standard tests as assembled products.
  • Swivel castor chair - the chair-wheel loading condition simulated by the test apparatus.

Who uses ISO 4918:2026?

ISO 4918:2026 is used by flooring manufacturers, test laboratories, certification bodies, technical specifiers and quality managers. It is relevant for products intended for offices, commercial interiors and other spaces where swivel chair use is expected.

Buyers and product developers use the standard to compare wear resistance and damage resistance across textile, resilient, laminate and MMF products. Laboratory staff use it to set up the apparatus, condition specimens, run the test and report the outcome in a consistent way.

What changed in ISO 4918:2026 from the previous edition?

ISO 4918:2026 is the third edition and cancels and replaces ISO 4918:2016/Amd 1:2018. The stated technical changes are the revision of information regarding the machine, the revision of information regarding fastening methods, and the addition of methods for testing modular mechanical locked floor coverings (MMF).

Which standards are used with ISO 4918:2026?

ISO 4918:2026 relies on the following referenced documents:

  • ISO 139:2005/Amd 1:2011 - provides the standard atmosphere for conditioning and testing textile specimens.
  • ISO 1957 - gives specimen selection and cutting rules for machine-made textile floor coverings.
  • ISO 2424 - supplies vocabulary for textile floor coverings.
  • ISO 9405 - provides the method for assessing changes in appearance of textile floor coverings.
  • EN 12466 - supplies vocabulary for resilient floor coverings.
  • EN 12529 - sets requirements for castors for swivel chairs.
  • EN 16511 - provides specification, requirements and test method language for modular mechanical locked floor coverings.
  • ASTM D7330 - offers an alternative method for assessing surface appearance change in pile floor coverings using standard reference scales.

What does the ISO 4918:2026 document contain?

ISO 4918:2026 contains apparatus descriptions, specimen preparation rules, conditioning instructions, testing procedures and inspection methods for both textile and non-textile floor coverings. It includes figures showing the castor chair apparatus, castor paths, specimen positioning, joint layouts, levelness checks and a sample evaluation template. It also includes the castor chair index formula for textile floor coverings and detailed test report content.

Annex A is an informative example showing how a specimen assembly can be inserted and clamped. That annex is useful for laboratories because it illustrates one practical way to secure the sample without interfering with the castor path.

Relations

Effective Date
12-Feb-2026
Effective Date
03-Sep-2022
Effective Date
03-Sep-2022

Buy Documents

Standard

ISO 4918:2026 - Resilient, textile, laminate and modular mechanical locked floor coverings — Castor chair test

Release Date:20-Nov-2026
English language (22 pages)
sale 15% off
Preview
sale 15% off
Preview
Standard

ISO 4918:2026 - Revêtement de sol textiles, résilients, stratifiés ou modulaire à verrouillage mécanique — Essai à l'appareil à roulettes

Release Date:20-Nov-2026
French language (22 pages)
sale 15% off
Preview
sale 15% off
Preview

Frequently Asked Questions

ISO 4918:2026 is a standard published by the International Organization for Standardization (ISO). Its full title is "Resilient, textile, laminate and modular mechanical locked floor coverings — Castor chair test". This standard covers: This document specifies methods for determining the change of appearance and stability of textile floor coverings or any damage caused by detachment of layers, opening of joints, cracks, or crazing of resilient, laminate or modular mechanical locked floor coverings under the movement of a swivel castor chair.

This document specifies methods for determining the change of appearance and stability of textile floor coverings or any damage caused by detachment of layers, opening of joints, cracks, or crazing of resilient, laminate or modular mechanical locked floor coverings under the movement of a swivel castor chair.

ISO 4918:2026 is classified under the following ICS (International Classification for Standards) categories: 97.150 - Floor coverings. The ICS classification helps identify the subject area and facilitates finding related standards.

ISO 4918:2026 has the following relationships with other standards: It is inter standard links to FprEN ISO 4918, ISO 4918:2016/Amd 1:2018, ISO 4918:2016. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

ISO 4918:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


International
Standard
ISO 4918
Third edition
Resilient, textile, laminate and
2026-11
modular mechanical locked floor
coverings — Castor chair test
Revêtement de sol textiles, résilients, stratifiés ou modulaire à
verrouillage mécanique — Essai à l'appareil à roulettes
Reference number
© ISO 2026
All rights reserved.
This ISO publication is protected by copyright and is owned by ISO and/or its licensors.
The content of this ISO publication is provided under licence, not sold. Use is subject to the applicable licence terms issued by ISO,
an ISO member body, or an authorized third-party distributor.
Except as required for implementation or expressly permitted by a separate licence, no part of this ISO publication may be
reproduced, distributed, modified, used, or made available in any form or by any means – electronic or mechanical, including
photocopying, scanning, recording, or posting on internal or external digital platforms.
Any use beyond the scope of the granted rights is prohibited and may result in legal action.
ISO copyright office
CP 401 • CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
6 Materials . 6
7 Sampling . 7
7.1 Textile floor coverings .7
7.2 Resilient floor coverings without mechanical locking system .7
7.3 Resilient, laminate and modular mechanical locked floor coverings with mechanical
locking systems . .8
8 Conditioning . 10
8.1 Textile floor coverings .10
8.2 Resilient, laminate and modular mechanical locked floor coverings .10
9 Procedure .10
9.1 Textile floor coverings .10
9.1.1 General .10
9.1.2 Mounting of the specimens .10
9.1.3 Verifications of the castors .10
9.1.4 Preparing of the apparatus .10
9.1.5 Test procedures .10
9.2 Resilient, laminate and modular mechanical locked floor coverings . 12
9.2.1 General . 12
9.2.2 Mounting of the specimen(s) . 12
9.2.3 Verification of the castors . 13
9.2.4 Preparing the apparatus . 13
9.2.5 Test procedure. 15
10 Assessment . .15
10.1 Textile floor coverings . 15
10.1.1 General . 15
10.1.2 Test A — Structural integrity assessment .16
10.1.3 Test A — Appearance retention assessment .16
10.1.4 Test B — Colour change assessment .16
10.1.5 Test C — Structural integrity assessment .16
10.2 Resilient, laminate and modular mechanical locked floor coverings .17
11 Calculations and expression of results . 17
11.1 Textile floor coverings .17
11.1.1 General .17
11.1.2 Castor index .17
11.2 Resilient, laminate and modular mechanical locked floor coverings .17
12 Test report . 17
12.1 General .17
12.2 Textile floor coverings .18
12.3 Resilient, laminate and modular mechanical locked floor coverings .18
Annex A (informative)  . 19

iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 219, Floor coverings, in collaboration with the
European Committee for Standardization (CEN) Technical Committee CEN/TC 134, Resilient, textile, laminate
and modular mechanical locked floor coverings, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 4918:2016/Amd 1:2018), which has been
technically revised.
The main changes are as follows:
— revision of information regarding the machine;
— revision of information regarding the fastening methods;
— addition of methods for testing modular mechanical locked floor coverings (MMF).
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.

iv
International Standard ISO 4918:2026(en)
Resilient, textile, laminate and modular mechanical locked
floor coverings — Castor chair test
1 Scope
This document specifies methods for determining the change of appearance and stability of textile floor
coverings or any damage caused by detachment of layers, opening of joints, cracks, or crazing of resilient,
laminate or modular mechanical locked floor coverings under the movement of a swivel castor chair.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
I S O 139:20 05/A M D1: 2011, Textiles — Standard atmospheres for conditioning and testing
ISO 1957, Machine-made textile floor coverings — Selection and cutting of specimens for physical tests
ISO 2424, Textile floor coverings — Vocabulary
ISO 9405, Textile floor coverings — Assessment of changes in appearance
EN 12466, Resilient floor coverings — Vocabulary
EN 12529, Castors and wheels — Castors for furniture — Castors for swivel chairs — Requirements
EN 16511, Modular mechanical locked floor coverings (MMF) — Specification, requirements and test method for
multilayer modular panels for floating installation
ASTM D7330, Standard Test Method for Assessment of Surface Appearance Change in Pile Floor Coverings Using
Standard Reference Scales
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 2424, EN 16511, EN 12466 and the
following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
crazing
fine random cracks apparent in the surface of floor coverings
Note 1 to entry: Crazing is generally caused by an applied stress acting on the surface.
Note 1 to entry: Applied stress can include, for example, sustained exposure to a rolling load.

4 Principle
A floor covering comprising one or more individual pieces with or without joint and treated or welded where
necessary, is submitted for a prescribed number of cycles to the action of three castors. The castors move in
epicyclical paths with multiple changes of direction, stops and starts, and the frequency of passage varies
from area to area.
For textile floor coverings, three different assessment methods are specified.
a) The change in appearance shall be assessed after 5 000 cycles and 25 000 cycles in accordance with
ISO 9405 (Test A) or ASTM D7330.
b) The change in colour shall be assessed by means of grey scales after 750 cycles in accordance with
ISO 9405 (Test B) or ASTM D7330.
c) The extent of deterioration shall be assessed after 10 000 cycles or 25 000 cycles (Test C).
For resilient, laminate or modular mechanical locked floor coverings, any damage to the specimen caused
during testing and visible as detachment of layers, opening of joints, cracking or crazing shall be assessed.
5 Apparatus
5.1 Rotating test platform
The rotating test platform on which the test specimen or the specimen support (5.9) together with the test
specimen is placed shall have a diameter of at least 795 mm (circular platform) or platform with a length
and width of at least 1 000 mm (square platform).
5.2 Castor assembly
This assembly comprises a vertical shaft, set in a bearing, and a plate on which the castors are mounted (see
Figure 1, item 1). This castor assembly is offset at a distance of (198 ± 1) mm from the centre of the rotating
test platform.
The three castors are each arranged concentrically at 120° intervals around the centre of the plate at a
distance of (130 ± 1) mm from the centre of the plate, and are free to rotate, so that they follow the rotation
of the castor assembly.
The tested area of the specimen is determined by the distance between the axes of revolution of the castor
chair assembly and the specimen table and by the distance of the castors from the centre of the plate. This
area is approximately 0,3 m .
Dimensions in millimetres
Key
1 shaft
2 distance >3 mm
3 load and or drive plate
4 castor mounting plate
5 chain
6 specimen
7 suction device with height regulation
8 rotating test platform
9 specimen support
Figure 1 — Typical castor chair apparatus
The castor assembly is loaded with additional weights to achieve a total load of (90 ± 2) kg equally divided
over the three castors.
The distance (under load) between the castor mounting plate and either the load or drive plate, or both,
shall be >3 mm.
Key
1 castor assembly
Figure 2 — Path of castors
5.3 Drive mechanism
The drive to the rotating test platform and to the castor assembly is interlocked and fitted with a reversing
mechanism. The number of cycles is set by means of a pre-set counter. The rotational speed of the rotating
-1 -1
platform shall be (19 ± 2) min and that of the castor assembly (50 ± 5) min .
After (180 ± 20) s of rotation, the platform shall stop and remain in the stop position for (5 ± 2) s, after which
time the direction of rotation of the rotating platform shall reverse.
The relationship between the rotational speed of the test platform and that of the castor assembly causes a
sharp reverse movement of the castors of about 160° at a point close to the outer edge of the stressed area
(see Figure 2).
5.4 Suction device
The suction capacity of the vacuum cleaner and the height of the suction device (see Figure 1, item 7) should
be able to remove all abrased material or dust in a way that the surface of the test specimen is always kept
clean during the test. A suction capacity of (30 ± 5) l/s is recommended to reach this requirement.
5.5 Castors
5.5.1 General
Single-wheel swivel castors shall be used having the following dimensions (see Figure 3):
a) diameter of the wheel: (50 ± 2) mm;
b) width of the wheel: (20 ± 2) mm;
c) radius of curvature, R, of castor tread: nominal 130 mm;
d) crank distance: (32 ± 2) mm.
The distance between any two castor mountings shall be (225 ± 5) mm.

Dimensions in millimetres
Figure 3 — Single-wheel swivel castors
1)
5.5.2 Type H castors conforming to EN 12529, suitable for resilient, textile, laminate and modular
mechanical locked floor coverings.
Type H castors shall have plain wheels and a hard tread. The castor treads shall be made from polyamide,
with a surface hardness of (95 ± 5) Shore A and shall be stored under exclusion of light. The wheels
shall be one colour over their entire surface. The surface of the castors shall be replaced after maximum
2 000 000 cycles of the rotating test platform. It is advisable to replace all three at the same time.
The castor treads shall be examined after each test to verify that they are still smooth, without any deep
scoring or encrusted hard particles. The tread shall be replaced if the dimensions of the wheel fall outside
the tolerances given in 5.5.1.
2)
5.5.3 Type W castors conforming to EN 12529, suitable for resilient, laminate and modular mechanical
locked floor coverings.
Type W castors shall have resilient-tyred wheels and a soft tread. The castor treads shall be made from
polyurethane, with a surface hardness of (90 ± 5) Shore A and shall be stored under exclusion of light. The
surface of the castors shall be replaced after maximum 1 000 000 cycles of the test platform. It is advisable
to replace all three at the same time.
1) An example of a commercially available "Type H" castor product is from Quanz-Machinenbau GmbH. This information
is given for the convenience of users of this document and does not constitute an endorsement by ISO of this product.
2) An example of a commercially available “Type W” castor product is “Maxtech UAK050x20-Ø6,1” from TENTE
International GmbH. This information is given for the convenience of users of this document and does not constitute an
endorsement by ISO of this product.

The castor treads shall be examined after each test to verify that they are still smooth, without any deep
scoring or encrusted hard particles. The tread shall be replaced if the dimensions of the wheel fall outside
the tolerances given in 5.5.1.
5.6 Lifting device, to raise the castor assembly above the test platform when the apparatus is stationary.
5.7 Cycle counter, for setting the number of cycles of the test platform.
5.8 Fastening system
Flooring specimens shall be securely held in place on the specimen support (5.9) using glue, tape, or
other suitable means. For loose-laid installations, the panels, sheets and tiles shall be secured at the outer
perimeter using tape, which may include a flooring product and an underlayment, a hold down ring, an outer
ring, hold down clamps (see Annex A) or other suitable means to prevent specimens, from shifting during
the test. The vertical force should be reduced to a minimum.
The fixing must ensure that no part of the assembly can move against any other part of the assembly,
meaning no movement between the specimen support (5.9) and the underlay and between the underlay and
the floor coverings and between the elements of the floor coverings. The vertical force should be reduced to
a minimum so that movement is just prevented and there is no vertical deformation of the sample.
5.9 Specimen support
The specimen support shall be placed on a plate of rigid plastic [e.g. poly(methyl methacrylate)] or su
...


Norme
internationale
ISO 4918
Troisième édition
Revêtement de sol textiles,
2026-11
résilients, stratifiés ou modulaire à
verrouillage mécanique — Essai à
l'appareil à roulettes
Resilient, textile, laminate and modular mechanical locked floor
coverings — Castor chair test
Numéro de référence
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2026
Tous droits réservés.
La présente publication de l’ISO est protégée par le droit d’auteur et demeure la propriété de l’ISO et/ou de ses concédants de
licence.
Le contenu de la présente publication de l’ISO est fourni sous licence, et n’est pas vendu. Son utilisation est soumise aux conditions
de licence applicables définies par l’ISO, un organisme membre de l’ISO, ou un distributeur tiers agréé.
Sous réserve des besoins liés à sa mise en œuvre ou d’une autorisation expresse prévue aux termes d’une licence distincte, aucune
partie de la présente publication de l’ISO ne peut être reproduite, distribuée, modifiée, utilisée ou mise à disposition sous quelque
forme ou par quelque moyen que ce soit – électronique ou mécanique, y compris la photocopie, la numérisation, l’enregistrement
ou la publication sur des plateformes numériques internes ou externes.
Toute utilisation hors du champ d’application des droits accordés est interdite et peut donner lieu à des poursuites judiciaires.
ISO copyright office
Case postale 401 • CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii
Sommaire Page
Avant-propos .iv
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Principe. 2
5 Appareillage . 2
6 Matériaux . 6
7 Échantillonnage . 7
7.1 Revêtements de sol textiles .7
7.2 Revêtements de sol résilients sans système de verrouillage mécanique .7
7.3 Revêtements de sol résilients, stratifiés et modulaires à verrouillage mécanique avec
des systèmes de verrouillage mécanique .8
8 Conditionnement .10
8.1 Revêtements de sol textiles .10
8.2 Revêtements de sol résilients, stratifiés et modulaires à verrouillage mécanique .10
9 Mode opératoire . 10
9.1 Revêtements de sol textiles .10
9.1.1 Généralités .10
9.1.2 Installation des éprouvettes .10
9.1.3 Vérifications des roulettes .10
9.1.4 Préparation de l'appareillage .10
9.1.5 Modes opératoires .11
9.2 Revêtements de sol résilients, stratifiés et modulaires à verrouillage mécanique . 12
9.2.1 Généralités . 12
9.2.2 Installation de l’éprouvette ou des éprouvettes . 12
9.2.3 Vérification des roulettes . 13
9.2.4 Préparation de l'appareillage . 13
9.2.5 Mode opératoire . . 15
10 Évaluation .15
10.1 Revêtements de sol textiles . 15
10.1.1 Généralités . 15
10.1.2 Essai A — Évaluation de l'intégrité structurelle .16
10.1.3 Essai A — Évaluation du changement d'aspect .16
10.1.4 Essai B — Évaluation du changement de coloris .16
10.1.5 Essai C — Évaluation de l'intégrité structurelle .16
10.2 Revêtements de sol résilients, stratifiés et modulaires à verrouillage mécanique .17
11 Calculs et expression des résultats . 17
11.1 Revêtements de sol textiles .17
11.1.1 Généralités .17
11.1.2 Indice de roulette .17
11.2 Revêtements de sol résilients, stratifiés et modulaires à verrouillage mécanique .17
12 Rapport d'essai .18
12.1 Généralités .18
12.2 Revêtements de sol textiles .18
12.3 Revêtements de sol résilients, stratifiés et modulaires à verrouillage mécanique .18
Annexe A (informative)  . 19

iii
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux
de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général
confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire
partie du comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (IEC) en ce qui concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document
a été rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2
(voir www.iso.org/directives).
L'ISO attire l'attention sur le fait que la mise en application du présent document peut entraîner l'utilisation
d'un ou de plusieurs brevets. L'ISO ne prend pas position quant à la preuve, à la validité et à l'applicabilité
de tout droit de propriété revendiqué à cet égard. À la date de publication du présent document, l'ISO
n'avait pas reçu notification qu'un ou plusieurs brevets pouvaient être nécessaires à sa mise en application.
Toutefois, il y a lieu d'avertir les responsables de la mise en application du présent document que des
informations plus récentes sont susceptibles de figurer dans la base de données de brevets, disponible à
l'adresse www.iso.org/brevets. L'ISO ne saurait être tenue pour responsable de ne pas avoir identifié tout ou
partie de tels droits de brevet.
Les appellations commerciales éventuellement mentionnées dans le présent document sont données pour
information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion de
l'ISO aux principes de l'Organisation mondiale du commerce (OMC) concernant les obstacles techniques au
commerce (OTC), voir www.iso.org/avant-propos.
Le présent document a été élaboré par le comité technique ISO/TC 219, Revêtements de sol, en collaboration
avec le comité technique CEN/TC 134, Revêtements de sol résilients, textiles, stratifiés et modulaires à
verrouillage, du Comité européen de normalisation (CEN), conformément à l’Accord de coopération technique
entre l’ISO et le CEN (Accord de Vienne).
Cette troisième édition annule et remplace la deuxième édition (ISO 4918:2016/Amd 1:2018), qui a fait l’objet
d’une révision technique.
Les principales modifications sont les suivantes:
— révision des informations relatives à la machine;
— révision des informations relatives aux méthodes de fixation;
— ajout de méthodes d’essai pour les revêtements de sol modulaires à verrouillage mécanique (MMF).
Il convient que l'utilisateur adresse tout retour d'information ou toute question concernant le présent
document à l'organisme national de normalisation de son pays. Une liste exhaustive desdits organismes se
trouve à l'adresse www.iso.org/fr/members.html.

iv
Norme internationale ISO 4918:2026(fr)
Revêtement de sol textiles, résilients, stratifiés ou modulaire
à verrouillage mécanique — Essai à l'appareil à roulettes
1 Domaine d'application
Le présent document spécifie des méthodes pour déterminer le changement d’aspect et de stabilité d’un
revêtement de sol textile ou toute détérioration causée par le décollement des couches, l’ouverture des joints,
l’apparition de fissures ou le faïençage d’un revêtement de sol résilient, stratifié ou modulaire à verrouillage
mécanique sous l’effet du déplacement d’un appareil à roulettes pivotantes.
2 Références normatives
Les documents suivants sont cités dans le texte de sorte qu’ils constituent, pour tout ou partie de leur
contenu, des exigences du présent document. Pour les références datées, seule l'édition citée s'applique. Pour
les références non datées, la dernière édition du document de référence s'applique (y compris les éventuels
amendements).
I S O 139:20 05/A M D1: 2011, Textiles — Atmosphères normales de conditionnement et d’essai
ISO 1957, Revêtements de sol textiles fabriqués à la machine — Sélection et prélèvement des éprouvettes en vue
des essais physiques
ISO 2424, Revêtements de sol textiles — Vocabulaire
ISO 9405, Revêtements de sol textiles — Évaluation des changements d’aspect
EN 12466, Revêtements de sol résilients — Vocabulaire
EN 12529, Roues et roulettes — Roulettes pour meubles — Roulettes pour sièges de bureau — Prescriptions
EN 16511, Revêtements de sol modulaires à verrouillage mécanique (MMF) — Spécifications, exigences et
méthodes d’essai pour panneaux multicouches modulaires pour pose flottante
ASTM D7330, Standard Test Method for Assessment of Surface Appearance Change in Pile Floor Coverings Using
Standard Reference Scales
3 Termes et définitions
Pour les besoins du présent document, les termes et les définitions de l’ISO 2424, l’EN 16511, et l’EN 12466
ainsi que les suivants s’appliquent.
L'ISO et l'IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en normalisation,
consultables aux adresses suivantes:
— ISO Online browsing platform: disponible à l'adresse https:// www .iso .org/ obp
— IEC Electropedia: disponible à l'adresse https:// www .electropedia .org/
3.1
faïençage
fines craquelures aléatoires apparentes à la surface d’un revêtement de sol, généralement provoquées par
une contrainte appliquée agissant sur la surface
Note 1 à l'article: La contrainte appliquée peut inclure, par exemple, une exposition prolongée à une charge roulante.

4 Principe
Un revêtement de sol, comprenant une ou plusieurs pièces individuelles, avec ou sans joints, et traités ou
soudés si nécessaire, est soumis à l’action de trois roulettes pendant un nombre de cycles prédéfini. Ces
roulettes se déplacent selon des trajectoires épicycloïdales avec de multiples changements de direction,
arrêts et démarrages, la fréquence de passage des roulettes variant de zone en zone.
Pour les revêtements de sol textiles, trois méthodes d’évaluation différentes sont spécifiées:
a) Le changement d’aspect doit être évalué après 5 000 cycles et 25 000 cycles conformément à l’ISO 9405
(essai A) ou à l’ASTM D7330.
b) Le changement de coloris doit être évalué au moyen d’échelles de gris après 750 cycles conformément à
l’ISO 9405 (essai B) ou à l’ASTM D7330.
c) L’étendue de la dégradation doit être évaluée après 10 000 cycles ou 25 000 cycles (essai C).
Pour des revêtements de sol résilients, stratifiés ou modulaires à verrouillage mécanique, toute détérioration
causée à l’éprouvette pendant un essai et visible sous la forme d’un décollement des couches, d’une ouverture
des joints, d’une fissuration ou d’un faïençage doit être évaluée.
5 Appareillage
5.1 Plateau d’essai rotatif
Le plateau d’essai rotatif sur lequel est placé l’éprouvette ou le porte-éprouvette (5.9) avec l’éprouvette
doit avoir un diamètre d’au moins 795 mm (plateau circulaire) ou une longueur et une largeur d’au moins
1 000 mm (plateau carré).
5.2 Dispositif à roulettes
Ce dispositif comprend un axe vertical, monté sur un roulement et comportant un plateau sur lequel
sont montées les roulettes (voir Figure 1, élément 1). Ce dispositif à roulettes est décalé d'une distance
de (198 ± 1) mm par rapport au centre du plateau d'essai rotatif.
Les trois roulettes sont disposées concentriquement, à 120° d'intervalle et à une distance de (130 ± 1) mm
du centre du plateau et tournent librement, de manière à suivre la rotation du dispositif.
La zone soumise à l'essai de l'éprouvette est déterminée par la distance entre l'axe du dispositif de l'appareil
à roulettes et celui du plateau d'essai, et par la distance entre les roulettes et le centre du plateau. Cette zone
mesure approximativement 0,3 m .

Dimensions en millimètres
Légende
1 axe
2 distance > 3 mm
3 plateau de charge et/ou d’entraînement
4 plateau de montage des roulettes
5 chaîne
6 éprouvette
7 dispositif d'aspiration réglable en hauteur
8 plateau d'essai rotatif
9 porte-éprouvette
Figure 1 — Appareillage d’essai à roulettes type
Le dispositif à roulettes est chargé de poids supplémentaires afin d’atteindre une charge totale de (90 ± 2) kg
uniformément répartie sur les trois roulettes.
La distance (sous charge) entre le plateau de montage des roulettes et le plateau de charge ou le plateau
d’entraînement, ou les deux, doit être > 3 mm.

Légende
1 dispositif à roulettes
Figure 2 — Trajectoire des roulettes
5.3 Mécanisme d’entraînement
Le mécanisme d'entraînement du plateau d'essai rotatif et celui du dispositif à roulettes est verrouillé et
muni d'un mécanisme d'inversion. Le nombre de cycles est fixé au moyen d'un compteur préréglé. La
−1
vitesse de rotation du plateau rotatif doit être de (19 ± 2) min , celle du dispositif à roulettes doit être
−1
de (50 ± 5) min .
Après (180 ± 20) s de rotation, le plateau doit s'arrêter et rester dans la position d'arrêt pendant (5 ± 2) s,
après quoi le sens de rotation du plateau rotatif doit s'inverser.
Le rapport entre la vitesse de rotation du plateau d’essai et celle du dispositif à roulettes provoque un
brusque pivotement des roulettes d’environ 160° en un point proche du bord extérieur de la zone sous
contrainte (voir Figure 2).
5.4 Dispositif d’aspiration
Il convient que la capacité d’aspiration de l’aspirateur et la hauteur du dispositif d’aspiration (voir Figure 1,
élément 7) permettent de retirer tout le matériau abrasé ou la poussière de manière à ce que la surface
de l’éprouvette d’essai reste toujours propre pendant l’essai. Une capacité d’aspiration de (30 ± 5) l/s est
recommandée pour répondre à cette exigence.
5.5 Roulettes
5.5.1 Généralités
Des roulettes pivotantes à roue unique doivent être utilisées et doivent présenter les dimensions suivantes
(voir Figure 3):
a) diamètre de la roue: (50 ± 2) mm;
b) largeur de la roue: (20 ± 2) mm;
c) rayon de courbure, R, de la bande de roulement de la roulette: valeur nominale 130 mm;
d) coude d’essieu: (32 ± 2) mm.

La distance entre deux montages de roulette doit être de (225 ± 5) mm.
Dimensions en millimètres
Figure 3 — Roulettes pivotantes à roue unique
1)
5.5.2 Roulettes de type H conformes à l’EN 12529, adaptées à des revêtements de sol résilients, textiles,
stratifiés et modulaires à verrouillage mécanique.
Les roulettes de type H doivent disposer de roues monobloc à bande de roulement dure. Les bandes de
roulement des roulettes doivent être en polyamide, avec une dureté de surface de (95 ± 5) Shore A et doivent
être stockées à l'abri de la lumière. La totalité de la surface des roues doit être monochrome. La surface des
roulettes doit être remplacée après un maximum de 2 000 000 de cycles du plateau d'essai rotatif. Il est
conseillé de les remplacer toutes les trois.
Les bandes de roulement des roulettes doivent être examinées après chaque essai afin de vérifier qu'elles
restent lisses, sans aucune éraflure profonde et sans incrustation de particules. Elles doivent être remplacées
si les dimensions de la roue tombent en dehors des tolérances établies au 5.5.1.
2)
5.5.3 Roulettes de type W conformes à l’EN 12529, adaptées à des revêtements de sol résilients,
stratifiés et modulaires à verrouillage mécanique.
Les roulettes de type W doivent disposer de roues à bandage résilient à bande de roulement souple. Les bandes
de roulement des roulettes doivent être en polyuréthane, avec une dureté de surface de (90 ± 5) Shore A et
doivent être stockées à l'abri de la lumière. La surface des roulettes doit être remplacée après un maximum
de 1 000 000 de cycles du plateau d'essai. Il est conseillé de les remplacer toutes les trois.
1) Un exemple de roulette de type H disponible dans le commerce est fourni par Quanz-Machinenbau GmbH. Cette
information est donnée à l’intention des utilisateurs du présent document et ne signifie nullement que l’ISO approuve ou
recommande l’emploi exclusif du produit ainsi désigné.
2) Un exemple de roulette de type W disponible dans le commerce est le modèle « Maxtech UAK050x20-Ø6,1 » de
TENTE International GmbH. Cette information est donnée à l’intention des utilisateurs du présent document et ne signifie
nullement que l’ISO approuve ou recommande l’emploi exclusif du produit ainsi désigné.

Les bandes de roulement des roulettes doivent être examinées après chaque essai afin de vérifier qu'elles
restent lisses, sans aucune éraflure profonde et sans incrustation de particules. Elles doivent être remplacées
si les dimensions de la roue tombent en dehors des tolérances établies au 5.5.1.
5.6 Système de levage, pour relever le dispositif à roulettes au-dessus du plateau d’essai à l’arrêt de
l’appareil.
5.7 Compte-cycles, destiné à régler le nombre de cycles du plateau d’essai.
5.8 Système de fixation
Les éprouvettes de sol doivent être positionnées de façon sécurisée sur le porte-éprouvette (5.9) à l’aide de
colle, d’adhésif ou de tout autre moyen adéquat.(Pour les installations dont la pose est libre, les panneaux, lés
et dalles doivent être sécurisés au niveau du périmètre extérieur à l’aide d’adhésif, ce qui peut comprendre
un produit de sol ainsi qu’une sous-couche, une bague de fixation, une bague extérieure, des pinces de
fixation (voir Annexe A) ou tout autre moyen adéquat pour empêcher les éprouvettes de bouger pendant
l’essai. Il convient de réduire la force verticale au minimum.
La fixation doit assurer qu’aucune partie du dispositif ne puisse se déplacer par rapport à une autre partie
du dispositif, ce qui signifie aucun mouvement entre le porte-éprouvette (5.9) et la sous-couche, et entre la
sous-couche et les revêtements de sol, et entre les éléments des revêtements de sol. Il convient de réduire la
force verticale au minimum afin que tout mouvement soit simplement évité et qu’il ne se produise aucune
déformation verticale de l’échantillon.
5.9 Porte-éprouvette
Le porte-éprouvette doit être placé sur une plaque de plastique rigide [par exemple, poly(méthacrylate
de méthyle)] ou un substrat adapté d’une épaisseur d’au moins 5 mm à 30 mm et d’un diamètre
approximativement identique à celui du plateau rotatif (5.1) ou d’environ les mêmes dimensions que le
plateau carré (5.1).
Le porte-éprouvette doit être installé sur le plateau d’essai rotatif et les trous créés sur le porte-éprouvette
doivent s’engager sur les ergots du plateau d’essai afin d’empêcher tout glissement.
5.10 Aspirateur externe, pour les revêtements de sol textiles, les revêtements de sol résilients, stratifiés
et modulaires à verrouillage mécanique.
5.11 Dispositif d’éclairage (à ne pas utiliser avec des revêtements de sol textiles)
Le dispositif d’éclairage doit créer un éclairement de (1 500 ± 300) lx au niveau de la table, de manière à
illuminer l’éprouvette par le dessus et à la verticale et à permettre une observation continue de celle-ci.
L'environnement doit être neutre et sombre.
L'éclairement doit être vérifié avant chaque série d'évaluations à l'aide d'un luxmètre.
5.12 Jauge d’épaisseur, de 0,50 mm.
5.13 Règle en acier, d’une longueur de 500 mm.
6 Matériaux
6.1 Tampon de coton blanc, ou papier.
6.2 Couche d’adhésif, ruban adhésif double face ou adhésif.
6.3 Éthanol dénaturé.
...