ISO/IEC 4078-2:2026
(Main)Sustainable mobility and transportation — Roadside feeding electric road system — Part 2: Service and operational concept
- Abstract
This document specifies the service and operational concept of the electric road system (ERS) with dynamic charging capability. The in-vehicle control system is not within the scope of this document.
- Status
- Published
- Publication Date
- 17-Nov-2026
- Current Stage
- 6060 - International Standard published
- Start Date
- 18-Nov-2026
- Completion Date
- 18-Nov-2026
ISO/IEC 4078-2:2026 is an International Standard from ISO and IEC for roadside feeding electric road systems (ERS) with dynamic charging capability. It specifies the service and operational concept for the roadside system, including how it is organized, how vehicles connect and disconnect, how charging is managed, and how fee handling is arranged. The in-vehicle control system is outside its scope.
What does ISO/IEC 4078-2:2026 specify?
ISO/IEC 4078-2:2026 specifies the service and operational concept of a roadside feeding ERS with dynamic charging capability. It is organized around system components, charging modes, communication, operational use cases, and fee management, so readers can see both the physical and digital parts of the service model.
| Annex | What it covers |
|---|---|
| Annex A | Informative use case examples for segmented charging feed lines and charging-right management |
The main body runs from Clause 1 to Clause 12. It covers the ERS concept from power source and infrastructure components through operational scenarios and charging fee management.
What are the key requirements of ISO/IEC 4078-2:2026?
ISO/IEC 4078-2:2026 sets out how a roadside feeding ERS should be structured and operated. The most practical points are the component model, charging modes, communication before power transfer, and the handling of charging rights and billing.
System and charging model
- Clause 4 identifies five system components: renewable energy power source, energy storage, power feeding facility, vehicle-feeding facility for vehicle-side power-receiving system facilities, and digital infrastructure for electric power management. For practice, this gives designers a clear architecture for what must be planned on the roadside side and what sits outside the document’s scope.
- Clause 4.1 and 4.2 link the ERS to renewable generation and energy storage. That matters because fluctuating renewable supply and demand surges must be managed in operation.
- Clause 5 distinguishes intermittent charging while driving from continuous charging while driving. In practice, this means ERS planners choose between partial roadside deployment and full roadside deployment depending on charging capacity and service concept.
- Clause 6 allows charging feed line segmentation. This supports safer operation and can help stop power to a segment when an unauthorized vehicle approaches, which is important for access control and incident response.
Operation, communication and safety
- Clause 7 sets the service concept: power feed to and from the vehicle, data aggregation from vehicle and ERS, security management of charging rights, fee collection, external data export, robust communication links, power management, weather monitoring, battery temperature management, GHG reduction management, and operational rules. In practice, this is the core operating model for service providers and system integrators.
- Clause 8 addresses physical components, including maintaining the right of way of the feed line and implementing safety measures such as protection against electric shock to vulnerable road users (VRU). That is the practical safety baseline for roadside installation.
- Clause 9 covers digital components, including a standardized data platform, shared data formats, and standardized interface protocols. This matters for interoperability and for avoiding vendor lock-in.
- Clause 10 requires wireless communication between the ERS and vehicle before power transfer begins, with authorization and data acquisition before feeding action. That means the system must confirm service conditions before energy transfer starts.
Service flow and fee handling
- Clause 11 defines the operational use cases and scenarios: approach, contact, request service, grant service, begin service, terminate service, and disconnect. It also states that the ERS shall stop operation immediately when the normal process is not completed in due time, which is a clear control rule for safe operation.
- Clause 12 sets the fee management concept. Both vehicle-side and infrastructure-side data are used to validate charging amount, and billing is based on validated vehicle data. This helps prevent incorrect charging records and supports privacy-aware billing.
What terms does ISO/IEC 4078-2:2026 define?
- Electric road system (ERS) - The roadside system that supplies electrical energy to vehicles while they are traveling.
- Dynamic charging - Charging that occurs while the vehicle is moving, rather than only when stationary.
- Electric road system service provider (ERSSP) - The entity that operates the ERS service and validates charging-related data.
- Security service provider (SSP) - The entity that manages security services for fee collection and related protection of data.
- Fee collection service provider (FCSP) - The entity that issues invoices and collects fees for ERS use.
- Vehicle identification number (VIN) - A vehicle identifier used in data exchange between the vehicle and the ERS.
- Greenhouse gas (GHG) - The emissions category the ERS is intended to reduce through renewable-powered road transport.
Who uses ISO/IEC 4078-2:2026?
ISO/IEC 4078-2:2026 is for road authorities, ERS operators, infrastructure engineers, digital platform designers, and mobility planners working on roadside dynamic charging. It is also relevant to fleet operators, commercial vehicle transportation companies, fee collection providers, and security service providers that must manage charging rights, data exchange, and billing.
In practice, these users apply the document when designing roadside power feeding, defining operating rules, setting up segmented feed lines, validating communication flows, and building fee and security processes for intercity commercial electric vehicle transport.
Which standards are used with ISO/IEC 4078-2:2026?
ISO 4078 (all parts) is the related series named in the bibliography. ISO/IEC 4078-2:2026 is part of that series and focuses on the service and operational concept for roadside feeding electric road systems.
What does the ISO/IEC 4078-2:2026 document contain?
The document includes a component model in Figure 1, showing the roadside power source, storage, feeding facility, vehicle-side interface, and digital infrastructure. It also presents charging modes, segmented feed line operation, and the communication link between the ERS and vehicles.
Clause 11 gives a step-by-step operational flow for approach, contact, request, grant, begin, terminate, and disconnect on both the vehicle side and the infrastructure side. Clause 12 adds the fee collection role model, while Annex A provides two use case examples showing how segmented charging feed lines can prevent unauthorized charging.
Get Certified
Connect with accredited certification bodies for this standard

BSI Group
BSI (British Standards Institution) is the business standards company that helps organizations make excellence a habit.

Bureau Veritas
Bureau Veritas is a world leader in laboratory testing, inspection and certification services.

DNV
DNV is an independent assurance and risk management provider.
Sponsored listings
Frequently Asked Questions
ISO/IEC 4078-2:2026 is a standard published by the International Organization for Standardization (ISO). Its full title is "Sustainable mobility and transportation — Roadside feeding electric road system — Part 2: Service and operational concept". This standard covers: This document specifies the service and operational concept of the electric road system (ERS) with dynamic charging capability. The in-vehicle control system is not within the scope of this document.
This document specifies the service and operational concept of the electric road system (ERS) with dynamic charging capability. The in-vehicle control system is not within the scope of this document.
ISO/IEC 4078-2:2026 is classified under the following ICS (International Classification for Standards) categories: 03.220.20 - Road transport; 13.020.20 - Environmental economics. Sustainability. The ICS classification helps identify the subject area and facilitates finding related standards.
ISO/IEC 4078-2:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
International
Standard
ISO/IEC 4078-2
First edition
Sustainable mobility and
2026-11
transportation — Roadside feeding
electric road system —
Part 2:
Service and operational concept
Mobilité et transports durables — Système routier électrique
d'alimentation en bord de route —
Partie 2: Service et concept opérationnel
Reference number
© ISO/IEC 2026
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
© ISO/IEC 2026 – All rights reserved
ii
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 System components . 1
4.1 Renewable energy power source .1
4.2 Energy storage .1
4.3 Power feeding facility .1
4.4 Vehicle-feeding facility for vehicle-side power-receiving system facilities .2
4.5 Digital infrastructure supporting the electric road system (ERS) for electric power
management .2
5 Charging modes . 3
5.1 General .3
5.2 Intermittent charging while driving .3
5.3 Continuous charging while driving . . .3
6 Charging feed line segmentation . 3
7 Services and concept of operations. 3
8 Physical components . 4
9 Digital components . 4
10 Communication link between the electric road system (ERS) and vehicles . 4
11 Operational use cases and scenarios . 5
11.1 General .5
11.2 Use cases .5
11.3 Scenarios: Common rule in all steps .5
11.4 Scenarios: Approach the electric road system (ERS): vehicle side .5
11.5 Scenarios: Approach the electric road system (ERS): infrastructure side .5
11.6 Scenarios: Contact the electric road system (ERS): vehicle side .5
11.7 Scenarios: Contact the electric road system (ERS): infrastructure side .6
11.8 Scenarios: Request service: vehicle side .6
11.9 Scenarios: Request service: infrastructure side .6
11.10 Scenarios: Grant service: vehicle side .6
11.11 Scenarios: Grant service: infrastructure side .6
11.12 Scenarios: Begin service: vehicle side .6
11.13 Scenarios: Begin service: infrastructure side .6
11.14 Scenarios: Terminate service: vehicle side .7
11.15 Scenarios: Terminate service: infrastructure side.7
11.16 Scenarios: Disconnect from the electric road system (ERS): vehicle side .7
11.17 Scenarios: Disconnect from the electric road system (ERS): infrastructure side .7
12 Electric road charging fee management . 7
12.1 General .7
12.2 Concept of service .8
Annex A (informative) Use case examples . 9
Bibliography .11
© ISO/IEC 2026 – All rights reserved
iii
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are
members of ISO or IEC participate in the development of International Standards through technical
committees established by the respective organization to deal with particular fields of technical activity.
ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations,
governmental and non-governmental, in liaison with ISO and IEC, also take part in the work.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of document should be noted. This document was drafted in accordance with the editorial rules of the ISO/
IEC Directives, Part 2 (see www.iso.org/directives or www.iec.ch/members_experts/refdocs).
ISO and IEC draw attention to the possibility that the implementation of this document may involve the
use of (a) patent(s). ISO and IEC take no position concerning the evidence, validity or applicability of any
claimed patent rights in respect thereof. As of the date of publication of this document, ISO and IEC had not
received notice of (a) patent(s) which may be required to implement this document. However, implementers
are cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents and https://patents.iec.ch. ISO and IEC shall not be held
responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www.iso.org/iso/foreword.html.
In the IEC, see www.iec.ch/understanding-standards.
This document was prepared by Joint Technical Committee ISO/IEC JTC 4, Smart and sustainable cities and
communities, Subcommittee SC 2, Sustainable Mobility and Transportation.
A list of all parts in the ISO/IEC 4078 series can be found on the ISO and IEC websites.
Any feedback or questions on this document should be directed to the user’s national standards
body. A complete listing of these bodies can be found at www.iso.org/members.html and
www.iec.ch/national-committees.
© ISO/IEC 2026 – All rights reserved
iv
Introduction
Achieving carbon neutrality for heavy-duty commercial vehicles, which are responsible for intercity freight
transport, is essential. Possible solutions include battery-electric vehicles (BEVs) and hydrogen-powered
vehicles.
There are challenges associated with using BEVs for long-haul intercity commercial transportation.
For large BEVs, long-distance travel that relies solely on stationary charging is inefficient and uneconomical
due to the significant time required for charging.
Therefore, an effective approach is to supply electricity from roadside infrastructure while the vehicle is in
motion on interurban corridors, thereby providing driving energy and charging the on-board battery.
At the beginning and end of a trip, the vehicle can operate as a pure BEV, producing no carbon dioxide
emissions. Various dynamic charging technologies – systems that provide electrical power to vehicles while
driving – have already been developed worldwide.
This document describes the service and operational concept of contact-type roadside electric road systems
(ERS).
To eliminate carbon dioxide emissions, the use of electric vehicles (EVs) powered by renewable energy is
important. Installing energy-storage equipment enables fluctuations in the load to be smoothed out when
variations in energy demand happen.
Safety measures to protect humans from hazards associated with roadside power-supply equipment are
important. In addition, cybersecurity measures are effective against cyber-attacks.
Authentication of both the power-supply side and the power-receiving side is also important to prevent
unauthorized energy use by third parties.
Only when these measures are taken can a highly reliable ERS be established.
The ISO 4078 series specifies the roadside ERS and related services supporting intercity commercial electric
vehicle transportation systems.
Because multiple methodologies exist for presenting the role and functional models, there is a need for
commonly understood presentation guidance and requirements. This document defines such guidance and
requirements for a generic roadside-powered electric road service role and functional model.
This document provides the service and operational concepts as a baseline. It intends to support, not hinder,
future business development, and to assist in developing business cases for other future road system
services beyond electric road services.
© ISO/IEC 2026 – All rights reserved
v
International Standard ISO/IEC 4078-2:2026(en)
Sustainable mobility and transportation — Roadside feeding
electric road system —
Part 2:
Service and operational concept
1 Scope
This document specifies the service and operational concept of the electric road system (ERS) with dynamic
charging capability.
The in-vehicle control system is not within the scope of this document.
2 Normative references
There are no normative references in this document.
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
4 System components
4.1 Renewable energy power source
The renewable energy power source component is labelled as key 1 in Figure 1, and it is the power source
for the ERS. It should use renewable power sources, such as solar power, wind turbines, or a combination of
both.
4.2 Energy storage
To cope with power demand surge and the instability of renewable power generation, installing the energy
storage facility is necessary for efficient electric road operation. The energy storage facility should be
installed.
The energy storage component is labelled as key 2 in Figure 1. Electric interface requirements are outside of
the scope of this document.
4.3 Power feeding facility
The power feeding facility component is labelled as key 3 in Figure 1. The power feeding system, installed
alongside the roadway, is a key component of this roadside feeding ERS. The interface to the electric vehicle
(EV) shall be standardized.
© ISO/IEC 2026 – All rights reserved
The safety measures to avoid human hazards from ERS should be built in.
The type of current in a power feeding facility is a.c. (number of phases) or d.c.
The voltage range in a power feeding facility is 200 V to 350 V, 5
...



