ISO 12571:2021
(Main)Hygrothermal performance of building materials and products — Determination of hygroscopic sorption properties
Hygrothermal performance of building materials and products — Determination of hygroscopic sorption properties
This document specifies two alternative methods for determining hygroscopic sorption properties of porous building materials and products: a) using desiccators and weighing cups (desiccator method); b) using a climatic chamber (climatic chamber method). The desiccator method is the reference method. This document does not specify the method for sampling. The methods specified in this document can be used to determine the moisture content of a sample in equilibrium with air at a specific temperature and humidity.
Performance hygrothermique des matériaux et produits pour le bâtiment — Détermination des propriétés de sorption hygroscopique
Le présent document décrit deux méthodes de détermination des propriétés de sorption hygroscopique des matériaux et produits poreux utilisés dans le bâtiment: la méthode utilisant des dessiccateurs et des coupelles de pesée (méthode du dessiccateur); la méthode utilisant une chambre climatique (méthode de la chambre climatique). La méthode du dessiccateur est la méthode de référence. Le présent document ne spécifie pas la méthode d’échantillonnage. Les méthodes décrites dans le présent document peuvent être utilisées pour déterminer la teneur en eau d’un échantillon en équilibre avec de l’air à température et humidité données.
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 12571
Third edition
2021-11
Hygrothermal performance of
building materials and products —
Determination of hygroscopic sorption
properties
Performance hygrothermique des matériaux et produits pour le
bâtiment — Détermination des propriétés de sorption hygroscopique
Reference number
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions, symbols and units . 1
3.1 Terms and definitions . 1
3.2 Symbols and units . 2
4 Principle . 2
4.1 Sorption curve . 2
4.2 Desorption curve . 2
5 Apparatus . 3
5.1 Desiccator method . 3
5.2 Climatic chamber method . 3
6 Test specimens . 3
6.1 Specification of the test specimens . 3
6.2 Number of test specimens . 3
7 Procedure .3
7.1 Test conditions . 3
7.2 Desiccator method . 4
7.2.1 General . 4
7.2.2 Sorption curve . 4
7.2.3 Desorption curve . 5
7.3 Climatic chamber method . 6
7.3.1 Sorption curve . 6
7.3.2 Desorption curve . 7
8 Calculation and expression of results . 7
8.1 Hygroscopic sorption . 7
8.2 Equilibrium moisture content curves . 7
9 Accuracy of measurement.8
9.1 Error in moisture content . . 8
9.2 Control of environmental conditions . 8
9.2.1 Desiccator method . 8
9.2.2 Climatic chamber method . 9
10 Test report . 9
Annex A (informative) Air relative humidities above saturated solutions in equilibrium .10
Annex B (informative) Preparation of saturated solutions .13
Annex C (informative) Example of the procedure for determining a point on a sorption
curve .16
Annex D (informative) Method using a glass jar .17
Bibliography .19
iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 163, Thermal performance and energy use
in the built environment Subcommittee SC 1, Test and measurement methods, in collaboration with the
European Committee for Standardization (CEN) Technical Committee CEN/TC 89, Thermal performance
of buildings and building components, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 12571:2013), which has been technically
revised.
The main changes are as follows:
— Table A.1 was revised.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
INTERNATIONAL STANDARD ISO 12571:2021(E)
Hygrothermal performance of building materials and
products — Determination of hygroscopic sorption
properties
1 Scope
This document specifies two alternative methods for determining hygroscopic sorption properties of
porous building materials and products:
a) using desiccators and weighing cups (desiccator method);
b) using a climatic chamber (climatic chamber method).
The desiccator method is the reference method.
This document does not specify the method for sampling.
The methods specified in this document can be used to determine the moisture content of a sample in
equilibrium with air at a specific temperature and humidity.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 9346, Hygrothermal performance of buildings and building materials — Physical quantities for mass
transfer — Vocabulary
ISO 12570, Hygrothermal performance of building materials and products — Determination of moisture
content by drying at elevated temperature
3 Terms and definitions, symbols and units
For the purposes of this document, the terms and definitions given in ISO 9346 and the following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1 Terms and definitions
3.1.1
equilibrium moisture content
moisture content of a porous material in equilibrium with the environment and the relative humidity of
the ambient air, at a specified temperature
3.1.2
moisture content mass by mass
mass of evaporable water divided by mass of dry material
3.1.3
moisture content volume by volume
volume of evaporable water divided by volume of dry material
3.1.4
moisture content mass by volume
mass of evaporable water divided by volume of dry material
Note 1 to entry: The mass of water is determined by weighing the specimen before and after drying at the
appropriate drying temperature until constant mass is reached.
3.1.5
sorption curve
curve established at a series of increasing equilibrium relative humidities at a given temperature
3.1.6
desorption curve
curve established at a series of decreasing equilibrium relative humidities at a given temperature
3.2 Symbols and units
Symbol Quantity Unit
m mass of test specimen kg
m mass of dried test specimen kg
u moisture content mass by mass kg/kg
3 3
ψ moisture content volume by volume m /m
w moisture content mass by volume kg/m
4 Principle
4.1 Sorption curve
The specimen is dried to constant mass. While maintaining a constant temperature, the specimen
is placed consecutively in a series of test environments, with relative humidity increasing in stages.
The moisture content is determined when equilibrium with each environment is reached. At this
point, a uniform moisture distribution in the sample is assumed. Equilibrium with the environment
is established by weighing the specime
...
NORME ISO
INTERNATIONALE 12571
Troisième édition
2021-11
Performance hygrothermique
des matériaux et produits pour
le bâtiment — Détermination des
propriétés de sorption hygroscopique
Hygrothermal performance of building materials and products —
Determination of hygroscopic sorption properties
Numéro de référence
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2021
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii
Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives .1
3 Termes, définitions, symboles et unités . 1
3.1 Termes et définitions . 1
3.2 Symboles et unités . 2
4 Principe. 2
4.1 Courbe de sorption . 2
4.2 Courbe de désorption . 2
5 Appareillage . 3
5.1 Méthode du dessiccateur . 3
5.2 Méthode de la chambre climatique . 3
6 Éprouvettes. 3
6.1 Caractéristiques de l’éprouvette . . 3
6.2 Nombre d’éprouvettes . 3
7 Mode opératoire . 4
7.1 Conditions d’essai . . . 4
7.2 Méthode du dessiccateur . 4
7.2.1 Généralités . 4
7.2.2 Courbe de sorption . 4
7.2.3 Courbe de désorption . 5
7.3 Méthode de la chambre climatique . 6
7.3.1 Courbe de sorption . 6
7.3.2 Courbe de désorption . 7
8 Calculs et expression des résultats .7
8.1 Sorption hygroscopique . 7
8.2 Courbes de teneur en eau d’équilibre . 7
9 Exactitude de mesure .8
9.1 Erreur sur la teneur en eau . 8
9.2 Contrôle des conditions ambiantes . 8
9.2.1 Méthode du dessiccateur . 8
9.2.2 Méthode de la chambre climatique . 9
10 Rapport d’essai . 9
Annexe A (informative) Humidités relatives de l’air au-dessus de solutions saturées
à l’équilibre .10
Annexe B (informative) Préparation de solutions saturées .13
Annexe C (informative) Exemple de mode opératoire pour la détermination d’un point sur
une courbe de sorption .16
Annexe D (informative) Méthode utilisant un flacon en verre .17
Bibliographie .19
iii
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes
nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est
en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.
L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir
www.iso.org/directives).
L’attention est attirée sur le fait que certains des éléments du présent document peuvent faire l’objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de
brevets reçues par l’ISO (voir www.iso.org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l’ISO liés à l’évaluation de la conformité, ou pour toute information au sujet de l’adhésion
de l’ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir le lien suivant: www.iso.org/iso/fr/avant-propos.html.
Le présent document a été élaboré par le comité technique ISO/TC 163, Performance thermique et
utilisation de l’énergie en environnement bâti, sous-comité SC 1, Méthodes d’essais et de mesurage,
en collaboration avec le comité technique CEN/TC 89, Performance thermique des bâtiments et des
composants du bâtiment, du Comité européen de normalisation (CEN), conformément à l’Accord de
coopération technique entre l’ISO et le CEN (Accord de Vienne).
Cette troisième édition annule et remplace la deuxième édition (ISO 12571:2013), qui a fait l’objet d’une
révision technique.
Les principales modifications sont les suivantes:
— le Tableau A.1 a été révisé.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes
se trouve à l’adresse www.iso.org/fr/members.html.
iv
NORME INTERNATIONALE ISO 12571:2021(F)
Performance hygrothermique des matériaux et produits
pour le bâtiment — Détermination des propriétés de
sorption hygroscopique
1 Domaine d’application
Le présent document décrit deux méthodes de détermination des propriétés de sorption hygroscopique
des matériaux et produits poreux utilisés dans le bâtiment:
a) la méthode utilisant des dessiccateurs et des coupelles de pesée (méthode du dessiccateur);
b) la méthode utilisant une chambre climatique (méthode de la chambre climatique).
La méthode du dessiccateur est la méthode de référence.
Le présent document ne spécifie pas la méthode d’échantillonnage.
Les méthodes décrites dans le présent document peuvent être utilisées pour déterminer la teneur en
eau d’un échantillon en équilibre avec de l’air à température et humidité données.
2 Références normatives
Les documents suivants sont cités dans le texte de sorte qu’ils constituent, pour tout ou partie de leur
contenu, des exigences du présent document. Pour les références datées, seule l’édition citée s’applique.
Pour les références non datées, la dernière édition du document de référence s’applique (y compris les
éventuels amendements).
ISO 9346, Performance hygrothermique des bâtiments et des matériaux pour le bâtiment — Grandeurs
physiques pour le transfert de masse — Vocabulaire
ISO 12570, Performance hygrothermique des matériaux et produits pour le bâtiment — Détermination du
taux d'humidité par séchage à chaud
3 Termes, définitions, symboles et unités
Pour les besoins du présent document, les termes et définitions donnés dans l’ISO 9346 ainsi que les
suivants, s’appliquent.
L’ISO et l’IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en
normalisation, consultables aux adresses suivantes:
— ISO Online browsing platform: disponible à l’adresse https:// www .iso .org/ obp
— IEC Electropedia: disponible à l’adresse https:// www .electropedia .org/
3.1 Termes et définitions
3.1.1
teneur en eau d’équilibre
teneur en eau d’un matériau poreux en équilibre avec l’environnement et l’humidité relative de l’air
ambiant, à une température spécifiée
3.1.2
teneur en eau massique
masse d’eau évaporable divisée par la masse de matériau sec
3.1.3
teneur en eau volumique
volume d’eau évaporable divisé par le volume du matériau sec
3.1.4
teneur en eau massique par volume
masse d’eau évaporable divisée par le volume du matériau sec
Note 1 à l'article: On détermine la masse d’eau en pesant l’éprouvette avant et après séchage à la température de
séchage appropriée jusqu’à obtention d’une masse constante.
3.1.5
courbe de sorption
courbe établie à des paliers d’hu
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.