IEC 60335-2-53:2011/AMD1:2017/COR1:2017
(Amendment)Corrigendum 1 - Amendment 1 - Household and similar electrical appliances - Safety - Part 2-53: Particular requirements for sauna heating appliances and infrared cabins
Corrigendum 1 - Amendment 1 - Household and similar electrical appliances - Safety - Part 2-53: Particular requirements for sauna heating appliances and infrared cabins
Corrigendum 1 - Amendement 1 - Appareils électrodomestiques et analogues - Sécurité - Partie 2-53: Règles particulières pour les appareils de chauffage de saunas et les cabines infrarouges
General Information
Relations
Standards Content (Sample)
IEC 60335-2-53:2011/AMD1:2017 – 1 –
/COR1:2017 IEC 2017
INTERNATIONAL ELECTROTECHNICAL COMMISSION
COMMISSION ÉLECTROTECHNIQUE INTERNATIONALE
____________
IEC 60335-2-53 IEC 60335-2-53
Edition 4.0 2011-04 Édition 4.0 2011-04
Amendment 1:2017-01 Amendement 1:2017-01
HOUSEHOLD AND SIMILAR ELECTRICAL APPAREILS ELECTRODOMESTIQUES ET
APPLIANCES – SAFETY – ANALOGUES – SECURITE –
Part 2-53: Particular requirements for sauna Partie 2-53: Règles particulières pour les
heating appliances and infrared cabins appareils de chauffage de saunas et les cabines
infrarouges
CO RRI G E NDUM 1
Corrections to the French version appear after the English text.
Les corrections à la version française sont données après le texte anglais.
INTRODUCTION
Replace:
The holder of this patent right has assured the IEC that he/she is willing to negotiate licences
either free of charge or under reasonable and non-discriminatory terms and conditions with
applicants throughout the world. In this respect, the statement of the holder of this patent right
is registered with IEC. Information may be obtained from:
By:
The holder of this patent right has assured the IEC that he/she is willing to negotiate licence
...
This May Also Interest You
IEC 60335-2-96:2024 deals with the safety of flexible sheet heating elements intended to be incorporated into floors and walls below 1,2 m and above 2,3 m and in ceilings, their rated voltage being not more than 250 V for single-phase installations and 480 V for other installations including direct current (DC) supplied appliances. Flexible sheet heating elements are converted into heating units that are incorporated in the building in accordance with the instructions after which the required level of protection against hazards is achieved.
Attention is drawn to the fact that
- in many countries, different wiring rules apply;
- for heating units intended to be used in vehicles or on-board ships or aircraft, additional requirements can be necessary;
- in many countries, additional requirements are specified by the national authorities for fire protection, the national authorities for building regulations, the national health authorities, the national authorities responsible for the protection of labour and similar authorities.
This standard does not apply to
- heating units intended exclusively for industrial purposes;
- heating units intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas);
- blankets, pads, clothing and similar flexible heating appliances (IEC 60335-2-17);
- foot warmers and heating mats (IEC 60335-2-81);
- heated carpets and for heating units for room heating installed under removable floor coverings (IEC 60335-2-106);
- flexible sheet heating elements incorporated in other appliances.
This third edition cancels and replaces the second edition published in 2019. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) alignment with IEC 60335-1:2020;
b) conversion of some notes to normative text (Clause 1, 5.2, 7.12.101);
c) correction to reinstate the touch current limit in 22.105.
This part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments unless that edition precludes it; in that case, the latest edition that does not preclude it is used. It was established on the basis of the sixth edition (2020) of that standard.
- Standard153 pagesEnglish languagesale 15% off
- Standard102 pagesEnglish and French languagesale 15% off
IEC 60335-2-111:2024 deals with the safety of electric ondol-mattresses for household and similar purposes, their rated voltage being not more than 250 V including direct current (DC) supplied appliances and battery-operated appliances. This standard also applies to control units supplied with the appliance.
Appliances not intended for normal household use, but that nevertheless can be a source of danger to the public, such as appliances intended to be used in community spas or by persons in cold ambient temperatures, are within the scope of this standard.
As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account:
- persons (including children) whose physical, sensory or mental capabilities; or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction;
- children playing with the appliance.
This standard does not apply to
- appliances intended exclusively for industrial purposes;
- appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas);
- blankets, pads and similar flexible heating appliances (IEC 60335-2-17);
- room heaters (IEC 60335-2-30);
- water bed heaters (IEC 60335-2-66);
- heating appliances for breeding and rearing animals (IEC 60335-2-71);
- foot warmers and heating mats (IEC 60335-2-81);
- flexible sheet heating elements for room heating (IEC 60335-2-96);
- heated carpets and heating units for room heating installed under removable floor coverings (IEC 60335 2 106);
- appliances specifically intended for use under medical supervision (IEC 80601-2-35).
This second edition cancels and replaces the first edition published in 2015. This edition constitutes a technical revision
This edition includes the following significant technical changes with respect to the previous edition:
a) alignment with IEC 60335-1:2020;
b) conversion of some notes to normative text (Clause 1);
c) application of test probe 19 has been introduced (8.1.1, 20.2, B.22.3, B.22.4).
This part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments unless that edition precludes it; in that case, the latest edition that does not preclude it is used. It was established on the basis of the sixth edition (2020) of that standard.
- Standard67 pagesEnglish languagesale 15% off
- Standard328 pagesEnglish languagesale 15% off
IEC 60335-2-81:2024 deals with the safety of electric foot warmers and heating mats for household and similar purposes, their rated voltage being not more than 250 V including direct current (DC) supplied appliances and battery-operated appliances.
Appliances not intended for normal household use but which nevertheless can be a source of danger to the public, such as appliances intended to be used by laypersons in shops, in light industry and on farms, are within the scope of this standard.
As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account
– persons (including children) whose physical, sensory or mental capabilities; or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction;
– children playing with the appliance.
Additional requirements can be necessary for appliances intended to be used in vehicles or on board ships or aircraft. In many countries, additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour, the national water supply authorities and similar authorities.
This standard does not apply to:
– appliances specifically intended for use under medical supervision;
– electric blankets and pads (IEC 60335-2-17);
– electrically heated carpets (IEC 60335-2-106);
– electrical heating appliances for breeding and rearing animals (IEC 60335-2-71).
This fourth edition cancels and replaces the third edition published in 2015, Amendment 1:2017 and Amendment 2:2020. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) alignment with IEC 60335-1:2020;
b) conversion of some notes to normative text (Clause 1, 13.2, 16.2, 21.103, 21.104, 21.105, 21.106);
c) addition of test probe 19 for accessibility (8.1.1, 8.1.3, 20.2, B.22.3, B.22.4);
d) addition of external surface temperatures (Clause 11);
e) addition of the test of 21.107 for control units intended to be placed on a surface;
f) alignment of 30.102 with IEC 60335-2-17.
This part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments unless that edition precludes it; in that case, the latest edition that does not preclude it is used. It was established on the basis of the sixth edition (2020) of that standard.
- Standard285 pagesEnglish languagesale 15% off
IEC 60335-2-61:2024 deals with the safety of electric thermal-storage room heaters for household and similar purposes that are intended to heat the room in which they are located, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances including direct current (DC) supplied appliances. Appliances not intended for normal household use but which nevertheless can be a source of danger to the public, such as appliances intended to be used by laypersons in shops, in light industry and on farms, are within the scope of this standard. As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home.
Attention is drawn to the fact that
- this standard only applies to self-contained thermal-storage room heaters. However, it can be used as a guide, in so far as it reasonably applies, to determine the requirements and test specifications for other thermal-storage room heaters;
- for heaters incorporating direct-acting heating elements, IEC 60335-2-30 is also applicable;
- for heaters intended to be used in vehicles or on board ships or aircraft, additional requirements can be necessary;
- in many countries additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour and similar authorities.
This standard does not apply to
- appliances intended exclusively for industrial purposes;
- heaters incorporated in the building structure;
- central heating systems;
- heaters for saunas (IEC 60335-2-53);
- flexible sheet heating elements for room heating (IEC 60335-2-96);
- heaters intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas).
This third edition cancels and replaces the second edition published in 2002, Amendment 1:2005 and Amendment 2:2008. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) alignment with IEC 60335-1:2020;
b) deletion or conversion of some notes to normative text (Clause 1, 7.1, 10.1, 19.3.102, 24.101);
c) application of test probe 19 has been introduced (8.1.1, 20.2);
d) temperature limits have been updated and requirements for measurement were defined (Clause 11.3, 11.8, Table 101);
e) implementation of Figure 101 with the probe for measuring surface temperatures.
This part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments unless that edition precludes it; in that case, the latest edition that does not preclude it is used. It was established on the basis of the sixth edition (2020) of that standard.
- Standard77 pagesEnglish languagesale 15% off
- Standard269 pagesEnglish languagesale 15% off
- Standard50 pagesEnglish and French languagesale 15% off
IEC 60335-2-106:2021 deals with the safety of
- portable heated carpets;
- heated carpets and similar appliances;
- heating units to heat the room in which they are located and that are intended to be installed directly under materials used as a removable floor covering such as carpet, cushion vinyl, or loose laid laminate,
their rated voltage being not more than 250 V for single-phase installations and 480 V for other installations, including direct current (DC) supplied appliances.
Attention is drawn to the fact that
- in many countries different wiring rules apply;
- for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements can be necessary;
- in many countries additional requirements are specified by the national authorities for fire protection, the national authorities for building regulations, the national health authorities, the national authorities responsible for the protection of labour and similar authorities.
This standard does not apply to
- appliances intended exclusively for industrial purposes;
- appliances intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas);
- blankets, pads and similar flexible heating appliances (IEC 60335-2-17);
- heated mats and foot warmers with an area not exceeding 0,5 m2 (IEC 60335-2-81);
- flexible sheet heating systems permanently incorporated in the floor of the building structure (IEC 60335-2-96);
- flexible heating elements incorporated in other appliances;
- battery-operated appliances.
This second edition cancels and replaces the first edition published in 2007. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) the text has been aligned with IEC 60335-1:2020;
b) some notes have been converted to normative text (Clause 1, 5.2, 5.3, 5.6, 7.12.1, 7.101, 10.1, 18.101.1, 18.101.2, 18.102.5, 19.1, 19.103, 21.1, 21.104, 21.105, 30.102);
c) requirements for portable heated carpets have been added (Clause 1, 5.2, 5.5, 6.1, 6.2, 7.1, 7.6, 7.12, 7.14, 7.101, 11.8, 15.1, 15.101, 16.1, 16.2, 16.3, 19.101, 19.102. 19.103, 21.105, 21.106, 24.1.5, 24.2, 29.3);
d) requirements for washable portable heated carpets have been added (5.3, 7.1, 7.6, 7.12, 7.14);
e) the test of 30.102 has been updated.
This Part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments unless that edition precludes it; in that case, the latest edition that does not preclude it is used. It was established on the basis of the sixth edition (2020) of that standard.
- Standard134 pagesEnglish languagesale 15% off
- Standard89 pagesEnglish and French languagesale 15% off
- Standard9 pagesEnglish and French languagesale 15% off
IEC 60335-2-30:2009 Deals with the safety of electric room heaters for household and similar purposes, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. Examples of appliances that are included are:
- convection heaters;
- fan heaters;
- heaters for greenhouses;
- liquid-filled radiators;
- panel heaters;
- radiant heaters;
- tubular heaters;
- ceiling mounted heat lamp appliances.
The principal changes in this edition as compared with the fourth edition of IEC 60335-2-30 are as follows:
- some additional instructions are introduced for heaters without a built-in thermostat,
- or those installed in the floor or in a bathroom (7.12 and 7.12.1);
- a spillage test is introduced for appliances having a grille and - that are built into the floor (15.2).
The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of publication.
This publication is to be read in conjunction with IEC 60335-1:2010. The contents of the corrigendum of November 2014 have been included in this copy.
- Standard30 pagesEnglish languagesale 15% off
- Standard61 pagesEnglish and French languagesale 15% off
- Standard153 pagesEnglish and French languagesale 15% off
- Standard161 pagesEnglish and French languagesale 15% off
- Standard8 pagesEnglish and French languagesale 15% off
IEC 60335-2-96:2019 deals with the safety of flexible sheet heating elements intended to be incorporated into floors and walls below 1,2 m and above 2,3 m and in ceilings, their rated voltage being not more than 250 V for single-phase installations and 480 V for other installations.
Flexible sheet heating elements are converted into heating units that are incorporated in the building in accordance with the instructions after which the required level of protection against hazards is achieved. Attention is drawn to the fact that:
– in many countries, different wiring rules apply;
– for heating units intended to be used in vehicles or on board ships or aircraft, additional requirements can be necessary;
– in many countries, additional requirements are specified by the national authorities for fire protection, the national authorities for building regulations, the national health authorities, the national authorities responsible for the protection of labour and similar authorities.
This standard does not apply to:
– heating units intended exclusively for industrial purposes;
– heating units intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas);
– blankets, pads, clothing and similar flexible heating appliances (IEC 60335-2-17);
– foot warmers and heating mats (IEC 60335-2-81);
– heated carpets and for heating units for room heating installed under removable floor coverings (IEC 60335-2-106);
– flexible sheet heating elements incorporated in other appliances.
This second edition cancels and replaces the first edition published in 2002, Amendment 1:2003 and Amendment 2: 2008. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the first edition:
– aligns the text with IEC 60335-1:2010, and its Amendments 1 and 2;
– some notes have been converted to normative text or deleted (5.6, 7.12.1, 10.1, 11.2.103, 13.1, 13.2, 16.2, 16.3, 18.101, 18.102.5, 21.1, 22.103, 22.105, 22.106);
– the strength test for heating units incorporating insulated wires intended to be installed in floors has been modified a (21.103);
– the scope and specific requirements have been added for heating units installed in walls below a height of 1,2 m (6.2, 7.1, 7.12.1, 7.12.6, 7.101, 11.2, 19.2, 22.106, 24.102, Annex AA).
- Standard150 pagesEnglish languagesale 15% off
- Standard100 pagesEnglish and French languagesale 15% off
- Standard2 pagesEnglish languagesale 15% off
- Standard4 pagesEnglish and French languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.