EN IEC 62841-2-19:2025/A11:2025

SLOVENSKI STANDARD
01-februar-2026
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 2-
19. del: Posebne zahteve za ročne skobeljnike - Dopolnilo A11
Electric motor-operated hand-held tools, transportable tools and lawn and garden
machinery - Safety - Part 2-19: Particular requirements for hand-held jointers
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und
Rasen- und Gartenmaschinen - Sicherheit - Teil 2-19: Besondere Anforderungen für
handgeführte Flachdübelfräsen
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses -
Sécurité - Partie 2-19: Exigences particulières pour les raboteuses portatives
Ta slovenski standard je istoveten z: EN IEC 62841-2-19:2025/A11:2025
ICS:
25.100.01 Rezalna orodja na splošno Cutting tools in general
25.140.20 Električna orodja Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 62841-2-19:2025/A11

NORME EUROPÉENNE
EUROPÄISCHE NORM December 2025
ICS 25.140.20
English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 2-19: Particular
requirements for hand-held jointers
Outils électroportatifs à moteur, outils portables et machines Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 2-19: Exigences transportable Werkzeuge und Rasen- und
particulières pour les raboteuses portatives Gartenmaschinen - Sicherheit - Teil 2-19: Besondere
Anforderungen für handgeführte Flachdübelfräsen
This amendment A11 modifies the European Standard EN IEC 62841-2-19:2025; it was approved by CENELEC on 2025-11-10. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62841-2-19:2025/A11:2025 E

Contents Page
1 Modification to Clause 2, “Normative references” . 5
2 Modifications to Clause 8, Marking and instructions . 5
3 Modification to Clause 19, “Mechanical hazards” . 5
4 Modification to Annex I, “Measurement of noise and vibration emissions” . 5
5 Modification to Annex K, “Battery tools and battery packs” . 5
6 Modification to Annex L, “Battery tools and battery packs provided with mains connection
or non-isolated sources” . 6
7 Modification to the Bibliography . 7
8 Addition of Annex ZA, “Normative references to international publications with their
corresponding European publications” . 7
9 Addition of Annex ZZ, “Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered” . 8
European foreword
This document (EN IEC 62841-2-19:2025/A11:2025 has been prepared by CLC/TC 116 “Safety and
environmental aspects of motor-operated electric tools”.
The following dates are fixed:
• latest date by which this document has to be (dop) 2026-12-31
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) 2029-12-31
conflicting with this document have to be
withdrawn
This document modifies by common modifications EN IEC 62841-2-19:2025, which consists of the text of
116/758/FDIS (future IEC 62841-2-19, Ed. 1) prepared by IEC/TC 116 “Safety of motor-operated electric tools”.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This series is divided into four parts.
Part 1: General requirements which are common to most hand-held electric motor operated tools (for the
purpose of this document referred to simply as tools) which could come within the scope of this document;
Part 2, 3 or 4: Requirements for particular types of tools which either supplement or modify the requirements
given in Part 1 to account for the particular hazards and characteristics of these specific tools.
The Part 2-19 is used in conjunction with EN 62841-1:2015 and its amendments.
The Part 2-19 supplements or modifies the corresponding clauses in EN 62841-1:2015 and its amendments,
so as to convert it into the European Standard: Particular requirements for hand-held jointers.
Where a particular subclause of Part 1 is not mentioned in the Part 2-19, that subclause applies. When this
document states “addition”, “modification” or “replacement”, the relevant text in Part 1 is to be adapted
accordingly.
The following print types are used:
— requirements; in roman type;
— test specifications: in italic type;
— notes: in smaller roman type.
The terms defined in Clause 3 are printed in bold typeface.
Subclauses, notes, tables and figures which are additional to those in Part 1 are numbered starting from 101.
Clauses, subclauses, notes, tables, figures and annexes which are additional to those in IEC 62841-2-19:2024
are prefixed “Z”.
This document follows the overall requirements of EN ISO 12100.
This document has been prepared under a standardization request addressed to CENELEC by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
For relationship with EU Legislation, see informative Annex ZZ, which is an integral part of this document.
Compliance with the clauses of Part 1 together with Part 2-19 provides one means of conforming with the
essential health and safety requirements of the Directive concerned.
Any feedback and questions on this document should be directed to the users’ national committee. A complete
listing of these bodies can be found on the CENELEC website.
1 Modification to Clause 2, “Normative references”
Add the following normative reference:
EN 847-1:2017, Tools for woodworking - Safety requirements - Part 1: Milling tools, circular saw blades
2 Modifications to Clause 8, Marking and instructions
Replace 8.14.2 b) 101) including NOTE 101 with the following text:
“101) Information on dimensions or type of disc cutters to be used, which conform to EN 847-1:2017;”
3 Modification to Clause 19, “Mechanical hazards”
Replace clause 19.9 with the following text:
“19.9  Addition:
Parts of the guarding system which have to be opened for replacement of the disc cutter may be opened
without the aid of a tool, provided these parts remain connected with the tool and the tool is not usable with
these parts in open position.”
Replace NOTE 101 after 19.102 with the following normative text:
“19.Z101  Disc cutter
The disc cutter(s) deliv
...