EN 140401:2002

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Blank Detail Specification: Fixed low power non wire-wound surface mount (SMD) resistorsVordruck für Bauartspezifikation: Oberflächenmontierbare nichtdrahtgewickelte Festwiderstände (SMD) niedriger BelastbarkeitSpecification particulière cadre: Résistances fixes non bobinées à faible dissipation pour montage en surface (CMS)Blank Detail Specification: Fixed low power non wire-wound surface mount (SMD) resistors31.040.10Fiksni uporFixed resistorsICS:Ta slovenski standard je istoveten z:EN 140401:2002SIST EN 140401:2003en01-oktober-2003SIST EN 140401:2003SLOVENSKI
STANDARD
EUROPEAN STANDARDEN 140401NORME EUROPÉENNEEUROPÄISCHE NORMMay 2002CENELECEuropean Committee for Electrotechnical StandardizationComité Européen de Normalisation ElectrotechniqueEuropäisches Komitee für Elektrotechnische NormungCentral Secretariat: rue de Stassart 35, B - 1050 Brussels© 2002 CENELEC -All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.Ref. No. EN 140401:2002 EICS 31.040.10Supersedes EN 140401:1996English versionBlank Detail Specification:Fixed low power non wire-woundsurface mount (SMD) resistorsSpecification particulière cadre:Résistances fixes non bobinéesà faible dissipation pour montageen surface (CMS)Vordruck für Bauartspezifikation:Oberflächenmontierbare nichtdraht-gewickelte Festwiderstände (SMD)niedriger BelastbarkeitThis European Standard was approved by CENELEC on 2001-12-01. CENELEC members are bound tocomply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving thisEuropean Standard the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such national standards may be obtained onapplication to the Central Secretariat or to any CENELEC member.This European Standard exists in three official versions (English, French, German). A version in anyother language made by translation under the responsibility of a CENELEC member into its ownlanguage and notified to the Central Secretariat has the same status as the official versions.CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands,Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.SIST EN 140401:2003

– 3 –EN 140401:2002ContentsIntroduction.41Characteristics and ratings.51.1Dimensions and ratings.51.2Derating curve.61.3Resistance range and tolerance on rated resistance.61.4Variation of resistance with temperature and temperature rise.71.5Climatic categories.81.6Limits for change of resistance at tests.81.7Non-linear properties.91.8Marking, packaging and ordering designation.91.8.1Component.91.8.2Package.91.8.3Packaging / Taping.101.8.4Ordering information.101.9Additional information (not for inspection purpose).101.9.1Storage.101.9.2Mounting.101.9.3Soldering process.111.9.4Use of cleaning solvents.112Quality assessment procedures.112.1General.112.1.1Zero defect approach.112.1.2100 %-Test.112.1.30 -Resistor.122.1.4Certificate of Conformity (CoC).122.1.5Certified test records.122.1.6Failure rate level (only version E).122.2Qualification Approval.122.2.1Version A.122.2.2Version E.122.3Quality conformance inspection.122.3.1Qualification approval according to EN 100114-2.122.3.2Technology approval according to EN 100114-6.132.3.3Non-conforming items.13Annex A (normative)
Fixed sample size Qualification Approval and Quality Conformance Inspection testschedule for fixed low power surface mounting (SMD) resistors.14Annex B (informative)
Letter symbols and abbreviations.18Annex C (normative)
Standards referred to in this specification.19SIST EN 140401:2003

by the CECC General Secretariat;[3] the number and issue number of the CECC generic and sectional specification as relevant; also national referenceif different;[4] the national number of the detail specification, date of issue and any further information required by the nationalsystem, together with any amendment numbers, if different from the CECC number;[5] a brief description of the component or range of components;[6] information on typical construction (where applicable).For [5] and [6] the text to be given in the detail specification should be suitable for an entry in CECC 00 200 (registerof approvals) and the “CENELEC Catalogue of European Standards”;[7] an outline drawing with the main dimensions which are of importance for interchangeability and/or reference tothe appropriate national or international document for outlines. Alternatively, this drawing may be given in anannex to the detail specification;[8] the level of quality assessment covered by the detail specification.SIST EN 140401:2003

– 5 –EN 140401:2002Specification available from:[1]EN 140401-.(Specification number)[2]Electronic components of assessed quality in accordance with:EN 60115-1:2001EN 140400:200X[3]Issue .(Month) (Year)[4]Fixed low power non wire-wound surfacemounting resistorsStyle .[5](Description of the component)[6]Other shapes are permitted within the given dimensions.Figure 1 - Outline and dimensions (see Table 1)[7]Assessment level EZaVersion A: with 100 %-testVersion E: with failure rate level and100 %-testStability classes[8]a for explanations on assessment level EZ see 2.1.1.NOTE
Version E is optional.1 Characteristics and ratingsVarious parameters of
this component are precisely specified in this specification. Unspecified parameters may varyfrom one component to another.1.1 Dimensions and ratingsTable 1 – Style and dimensionsStyleLength LmmmmmmmmMetricinchmin.max.min.max.min.max.min.max.NOTE
See EN 140400, 1.2 a).Table 2a – RatingsStyleaRated dissipationP70mWLimiting element voltaged.c. or a.c. (r.m.s) UmaxVInsulation voltaged.c. or a.c. (peak) UinsV1 mincontinuousa Column for additional information (e.g. stability class, rated dissipation other ambient temperatures than 70 °C).NOTE 1
See EN 140400, 1.2 g), h), i).NOTE 2
Should it be necessary to control further parameters a more detailed specification should be used. Then the additional test method(s) shall befully described, and appropriate limits, AQLs and Inspection Levels shall be specified.Information about manufacturers who have components qualified to this detail specification is available in thecurrent CECC 00 200: Register of ApprovalsSIST EN 140401:2003

Table 2b is optional.1.2 Derating curveResistors covered by this specification are derated according to the following diagram:LCT+70 °CUCT0%100%Upper CategoryTemperatureLower CategoryTemperatureArea of recommended operationRated DissipationAmbient Temperature ambFigure 2 – Derating curveNOTE 1
See EN 140400, 1.2 g).NOTE 2
A larger area of operation may be given in the detail specification provided it includes all the are given above.1.3 Resistance range and tolerance on rated resistanceNOTE 1
See EN 140400, 1.2 d), e), f).Version A:The following combinations of temperature coefficient, tolerance on rated resistance shall be used for qualificationapproval according to 2.2.1 and quality conformance inspection according to 2.3. Resistance values of E-seriesaccording to IEC 60063 shall be used.The qualification of resistance values below or beyond the specified resistance values is permitted, if they fulfil therequirements of the closest stability class ( e.g. RR 1608M 1 % >1 M shall fulfil the requirements of stabilityclass 1).SIST EN 140401:2003

– 7 –EN 140401:2002Table 3a – Resistance range, tolerance on rated resistance for version AStyleTolerance onrated resistanceTemperaturecoefficientResistance rangeStability classE series(optional)%Codeappm/K0 -resistors according to Table 2b for all stylesa Code letters according to EN 60062.Version E:The following combinations of temperature coefficient, tolerance on rated resistance and E-series according toIEC 60063 shall be used for qualification approval according to 2.2.2 and quality conformance inspection according to2.3 and are permitted only:Table 3b – Resistance range, tolerance on rated resistance for version EStyleTolerance onrated resistanceTemperaturecoefficientResistance rangeStability classE series%Codeappm/K0 -resistors according to Table 2b for all styles.a Code letters according to EN 60062.NOTE 2
Table 3b is only required for version E and should be a subset of Table 3a.1.4 Variation of resistance with temperature and temperature riseTable 4 – Temperature coefficients and percentage change of resistance (acc. to EN 140400, Table 2)TemperaturecoefficientLimit of resistance change R/R%Stability classes .Stability classes .ppm/KCodeaTemp. charact.20 °C / 70 °CLCT / Ref.temp.Ref. temp. / UCT.LCT / Ref.temp.Ref. temp./ UCT.a Code letter according to EN 140400, Table 2.NOTE
See EN 140400, 1.2 f).SIST EN 140401:2003

See EN 140400, 1.2 b).Table 6 – Climatic categoriesStabilityclassClimatic categoryLCT / UCT / Duration1.6 Limits for change of resistance at testsNOTE
See EN 140400, 1.2. c).Table 7 – Limits for change of resistance at testsStabilityclassLimit of resistance change R/REN 60115-1,4.23Climatic sequence4.24Damp heat, steadystate4.25.3Endurance at uppercategorytemperatureEN 60115-1,4.25.1Endurance at 70 °CEN 60115-1,4.13Overload4.18Resistance tosoldering heat4.19Rapid change oftemperature4.22Vibration1 000 hExtended, 8 000 h4.33Substrate bendingtestSIST EN 140401:2003

– 9 –EN 140401:20021.7 Non-linear properties(for resistance values
10 )If measurement of non-linearity according to 2.1.1 is required the measured values shall be above the limits given inthe diagram below. The resistors shall be tested according to IEC 60440 where the test voltage shall be the ratedvoltage.101001k10k100k1M0dB20dB40dB60dB80dB100dB120dBAttenuation of 3rd Harmonic A3Resistance ValueFigure 3 – Limits of non-linearity in resistorsNOTE
X-scale shall be in accordance to the resistance range given in Table 3a.1.8 Marking, packaging and ordering designationNOTE
The marking of components and package shall be in accordance with the requirements of EN 60115-1, 2.4 and EN 140400, 1.2 k), l).1.8.1 ComponentNOTE
Marking of the component can be mandatory or not.1.8.2 PackageThe package of the component shall be marked with ordering information in accordance to 1.8.4 with additionally CECC sign of conformity, CECC manufacturer code, NATO manufacturer code (only version E, if required), Date code of manufacture according to EN 60062, additional information is allowed.SIST EN 140401:2003

The detail specification may include information (which is not required to be verified by the inspection proce
...