EN 60384-19-1:2006

STANDARDNespremenljivi kondenzatorji za elektronsko opremo – 19. del: Okvirna podrobna specifikacija – Nespremenljivi kondenzatorji za enosmerni tok za površinsko montažo s pokovinjenim polietilen-tereftalatnim dielektrikom – Ocenjevalni nivo EZ (IEC 60384-19-1:2006)Fixed capacitors for use in electronic equipment – Part 19-1: Blank detail specification – Fixed metallized polyethylene-terephthalate film dielectric surface mount d.c. capacitors – Assessment level EZ (IEC 60384-19-1:2006)©
Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljenoReferenčna številkaSIST EN 60384-19-1:2006(en)ICS31.060.10

EUROPEAN STANDARD EN 60384-19-1 NORME EUROPÉENNE
EUROPÄISCHE NORM March 2006
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2006 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60384-19-1:2006 E
ICS 31.060.10
English version
Fixed capacitors for use in electronic equipment Part 19-1: Blank detail specification -
Fixed metallized polyethylene-terephthalate film dielectric
surface mount d.c. capacitors -
Assessment level EZ (IEC 60384-19-1:2006)
Condensateurs fixes utilisés
dans les équipements électroniques Partie 19-1: Spécification particulière cadre -
Condensateurs fixes chipses pour courant continu à diélectrique en film
de polytéréphtalate d'éthylène métallisé - Niveau d'assurance EZ (CEI 60384-19-1:2006)
Festkondensatoren zur Verwendung
in Geräten der Elektronik Teil 19-1: Vordruck für Bauartspezifikation - Oberflächenmontierbare Gleichspannungs-Kondensatoren mit metallisierter Polyethylen-Terephtalat-Folie
als Dielektrikum -
Qualitätsbewertungsstufe EZ (IEC 60384-19-1:2006)
This European Standard was approved by CENELEC on 2006-02-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.

- 2 - Foreword The text of document 40/1623/FDIS, future edition 2 of IEC 60384-19-1, prepared by IEC TC 40, Capacitors and resistors for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60384-19-1 on 2006-02-01. The following dates were fixed: – latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement
(dop)
2006-11-01 – latest date by which the national standards conflicting
with the EN have to be withdrawn
(dow)
2009-02-01 This European Standard makes reference to International Standards. Where the International Standard referred to has been endorsed as a European Standard or a home-grown European Standard exists, this European Standard shall be applied instead. Pertinent information can be found on the CENELEC web site. __________ Endorsement notice The text of the International Standard IEC 60384-19-1:2006 was approved by CENELEC as a European Standard without any modification. __________

INTERNATIONAL STANDARD IEC60384-19-1 QC 302201Second edition2006-01 Fixed capacitors for use in electronic equipment –Part 19-1: Blank detail specification – Fixed metallized polyethylene-terephthalate film dielectric surface mount d.c. capacitors Assessment level EZ
 IEC 2006

Copyright - all rights reserved No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Electrotechnical Commission,
3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, SwitzerlandTelephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch
Web: www.iec.ch M For price, see current cataloguePRICE CODE
Commission Electrotechnique InternationaleInternational Electrotechnical Commission

– 2 – 60384-19-1  IEC:2006(E) INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –
Part 19-1: Blank detail specification – Fixed metallized polyethylene-terephthalate film dielectric surface mount d.c. capacitors – Assessment level EZ
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60384-19-1 has been prepared by IEC technical committee 40: Capacitors and resistors for electronic equipment. This second edition cancels and replaces the first edition published in 1993 and constitutes
minor revisions related to tables, figures and references. The text of this standard is based on the following documents: FDIS Report on voting 40/1623/FDIS 40/1646/RVD
Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

60384-19-1  IEC:2006(E) – 3 – IEC 60384 consists of the following parts, under the general title Fixed capacitors for use in electronic equipment: Part 1:
Generic specification Part 2:
Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric d.c. capacitors Part 3:
Sectional specification: Fixed tantalum surface mount capacitors Part 4:
Sectional specification: Aluminium electrolytic capacitors with solid and non-solid electrolyte Part 5:
Sectional specification: Fixed mica dielectric d.c. capacitors with a rated voltage not exceeding 3000 V – Selection of methods of test and general requirements Part 6:
Sectional specification: Fixed metallized polycarbonate film dielectric d.c. capacitors Part 8:
Sectional specification: Fixed capacitors of ceramic dielectric, Class 1 Part 9:
Sectional specification: Fixed capacitors of ceramic dielectric, Class 2 Part 11:
Sectional specification: Fixed polyethylene-terephthalate film dielectric metal foil d.c. capacitors Part 12:
Sectional specification: Fixed polycarbonate film dielectric metal foil d.c. capacitors Part 13:
Sectional specification: Fixed polypropylene film dielectric metal foil d.c. capacitors Part 14:
Sectional specification: Fixed capacitors for electromagnetic interference suppression and connection to the supply mains Part 15:
Sectional specification: Fixed tantalum capacitors with non-solid or solid electrolyte Part 16:
Sectional specification: Fixed metallized polypropylene film dielectric d.c. capacitors Part 17:
Sectional specification: Fixed metallized polypropylene film dielectric a.c. and pulse capacitors Part 18:
Sectional specification: Fixed aluminium electrolytic surface mount capacitors with solid and non-solid electrolyte Part 19:
Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric surface mount d.c. capacitors Part 20:
Sectional specification: Fixed metallized polyphenylene sulfide film dielectric surface mount d.c. capacitors Part 21:
Sectional specification: Fixed surface mount multilayer capacitors of ceramic dielectric, Class 1 Part 22:
Sectional specification: Fixed surface mount multilayer capacitors of ceramic dielectric, Class 2
Part 23:
Sectional specification – Fixed surface mount metallized polyethylene naphthalate film dielectric DC capacitors
Part 24:
Sectional specification – Surface mount fixed tantalum electrolytic capacitors with conductive polymer solid electrolyte 1 Part 25:
Sectional specification – Surface mount fixed aluminium electrolytic capacitors with conductive polymer solid electrolyte1 The QC number that appears on the front cover of this publication is the specification number in the IECQ Quality Assessment System for Electronic Components. ___________ 1 To be published.

– 4 – 60384-19-1  IEC:2006(E) The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to the specific publication. At this date, the publication will be
• reconfirmed; • withdrawn; • replaced by a revised edition, or • amended. A bilingual edition of this blank detail specification may be issued at a later date.

60384-19-1  IEC:2006(E) – 5 – FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –
Part 19-1: Blank detail specification – Fixed metallized polyethylene-terephthalate film dielectric surface mount d.c. capacitors – Assessment level EZ
Blank detail specification A blank detail specification is a supplementary document to the sectional specification and contains requirements for style and layout and minim
...