Abstract

IEC 60115-8-10:2026 is applicable to the drafting of detail specifications for surface mount (SMD) low-power film resistors, classified to level G, based on the definition of the product classification levels in IEC 60115‑1:2020, 3.4. This edition includes the following significant technical changes with respect to the previous edition IEC 60115‑8‑1:2014: a) it supports solderability testing for both traditional lead-bearing soldering and up-to-date lead-free soldering, as required; b) it supports the provision of detailed visual acceptance criteria; c) it includes the requirement for a visual examination of the primary and proximity packaging; d) it provides for the inclusion of specific visual acceptance criteria, to be applied in addition to those given in Annex B of the sectional specification IEC 60115‑8:2023.

Status
Published
Publication Date
29-Oct-2026
Technical Committee
CLC/TC 40XB - CLC/TC 40XB
Current Stage
6060 - Document made available - Publishing
Start Date
30-Oct-2026
Due Date
31-May-2024
Completion Date
30-Oct-2026

Buy Documents

Standard

EN IEC 60115-8-10:2026

English language (50 pages)
Preview
Preview
e-Library read for
×1 day

EN IEC 60115-8-10:2026 is the CLC/IEC blank detail specification for surface mount (SMD) low-power film resistors for assembly on circuit boards, classified to level G. It is a drafting template for product-specific detail specifications, so it tells manufacturers, labs, and certification bodies what information, test schedules, and acceptance criteria need to be written for this resistor family. In practice, it is used when the target products are for general electronic equipment, where the main requirement is function under benign or moderate environmental conditions.

What does EN IEC 60115-8-10:2026 specify?

EN IEC 60115-8-10:2026 specifies how to draft detail specifications for SMD low-power film resistors at classification level G, based on the product classification levels in IEC 60115-1. It is a blank detail specification, so its role is to define the structure and minimum content of a detail specification rather than a finished product range.

The document is organized into clauses on scope, normative references, terms and definitions, characteristics and ratings, tests and test severities, performance requirements, marking, packaging and ordering information, additional information, and quality assessment procedures. It also contains normative annexes for symbols and abbreviated terms, visual examination references, and 0 Ω resistors, plus an informative annex cross-referencing the prior revision.

AnnexWhat it covers
Annex ASymbols and abbreviated terms used in the document
Annex BReference material for visual examination
Annex CSpecial provisions for 0 Ω resistors (jumpers)
Annex XCross-references to the prior revision

What are the key requirements of EN IEC 60115-8-10:2026?

EN IEC 60115-8-10:2026 sets out the data and test framework that a drafted detail specification must contain. The most important points are the component dimensions, ratings, test severities, acceptance limits, marking and packaging rules, and the quality assessment schedules.

Characteristics, dimensions, and ratings

Clause 4 requires the resistor outline to be defined by figure and table, with the dimensions to be stated so they can be checked in practice. That matters because it fixes the package style and the mechanical fit on printed circuit boards.

Clause 4.3 defines climatic categories, rated dissipation at 70 °C, limiting element voltage, and insulation voltage, and it uses a derating curve above 70 °C. In practice, this tells a buyer or designer how much power the resistor may dissipate as ambient temperature rises.

Clause 4.4 links resistance range, tolerance on resistance, temperature coefficient, and climatic category. It also points to IEC 60062 for coding and IEC 60063 for preferred value series, which matters because only certain resistance values and codes belong in the approved range.

Test methods and severities

Clause 5 prescribes the test program, and specimens are generally mounted on a test board unless a special method is stated. The clause covers resistance, temperature coefficient of resistance, temperature rise, endurance at the rated temperature 70 °C, endurance at UCT, short-term overload, electrostatic discharge (ESD), visual examination, gauging of dimensions, detail dimensions, shear, substrate bending, rapid change of temperature, climatic sequence, damp heat, solderability, resistance to soldering heat, solvent resistance, insulation resistance, voltage proof, and flammability.

The solderability clauses are written for both lead-free solder and SnPb solder. That matters because a detail specification can be aligned either with current lead-free assembly or with older lead-bearing processes, and the compatibility choice has to be clear in the title block and in clause 8.4.

Clause 5 also defines specific conditions for several tests, such as the ESD human body model, the low air pressure condition in the climatic sequence, and the solder bath conditions for solvent and soldering tests. In practice, this removes ambiguity for test laboratories and makes qualification results comparable.

Performance requirements and pass/fail limits

Clause 6 turns the test program into acceptance limits. It sets the permissible change of resistance at the different tests, the allowable variation with temperature, and the temperature-rise limit based on maximum element temperature (MET) and UCT.

For visual examination, Clause 6 allows the drafted detail specification to state criteria for the resistor body, terminations, marking, and packaging. That matters because visual acceptance often drives incoming inspection and release decisions.

Clause 6 also gives insulation resistance requirements for insulated resistors and a flammability requirement based on burning time after the needle flame is removed. In practice, these values become the pass/fail criteria used after the tests in Clause 5.

Marking, packaging, ordering, and quality assessment

Clause 7 covers marking of the component, packaging, marking of the packaging, and ordering information. It points to tape packaging in IEC 60286-3 and requires the primary and proximity packaging to be visually examined, which matters for automated handling and for shipment quality.

Clause 9 defines the quality assessment flow, including 100 % resistance testing during manufacture, reinspection by sampling, qualification approval, and quality conformance inspection. Tables 12 and 13 give the test schedules for qualification and lot-by-lot or periodic inspection, so the document is directly usable for approval and ongoing production control.

Annex C is important if 0 Ω resistors are included. It changes the normal rules to suit jumpers by using residual resistance limits, special rating data, and modified test applicability.

What terms does EN IEC 60115-8-10:2026 define?

  • Surface mount (SMD) - A component intended to be mounted directly on the surface of a circuit board.
  • Lower category temperature (LCT) - The lower temperature limit used for climatic categories and temperature-related tests.
  • Upper category temperature (UCT) - The upper temperature limit used for climatic categories and endurance testing.
  • Maximum element temperature (MET) - The highest element temperature used as the basis for UCT and temperature-rise calculations.
  • Human body model (HBM) - The ESD test model that represents a discharge from a human body.
  • Temperature coefficient of resistance (TCR) - The rate at which resistance changes with temperature.
  • IECQ Certification Body (IECQ CB) - A certification body operating within the IECQ quality assessment system.
  • 0 Ω resistor - A jumper-type resistor with residual resistance rules instead of normal resistance, tolerance, and TCR rules.

Who uses EN IEC 60115-8-10:2026?

Manufacturers of fixed resistors use EN IEC 60115-8-10:2026 when preparing detail specifications for SMD low-power film resistors. Quality managers and test laboratories use it to build qualification and conformance test plans, including solderability, endurance, ESD, and visual checks.

Buyers and component engineers use it to define what information must appear in the ordering designation, packaging, and product approval records. Certification bodies and IECQ-related assessment organizations use it as the framework for approving and maintaining conformity of this resistor family.

What changed in EN IEC 60115-8-10:2026 from the previous edition?

EN IEC 60115-8-10:2026 replaces IEC 60115-8-1:2014 and is described as a technical revision. The significant changes stated in the document are:

  • It supports solderability testing for both traditional lead-bearing soldering and lead-free soldering.
  • It supports detailed visual acceptance criteria.
  • It requires visual examination of the primary and proximity packaging.
  • It allows specific visual acceptance criteria to be added alongside those in Annex B of IEC 60115-8:2023.
  • The sequence of the test clauses has been reorganized to follow the test prescription sequence in IEC 60115-1:2020.

Which standards are used with EN IEC 60115-8-10:2026?

  • IEC 60062:2019 - Provides marking codes for resistors and capacitors, used for resistance and TCR coding and for component marking.
  • IEC 60063 - Provides preferred number series, used when selecting resistance values.
  • IEC 60115-1:2020 - The generic specification for fixed resistors; it supplies the core definitions, tests, and quality assessment framework.
  • IEC 60115-8:2023 - The sectional specification for fixed surface mount resistors; it supplies the common SMD requirements and many referenced test prescriptions.
  • IEC 60286-3 - Covers packaging of components on continuous tapes, used for primary packaging of the resistors.
  • IEC 61760-1 - Gives the standard method for specifying surface mounting components, used for assembly-related description.
  • IEC 61193-2:2007 - Provides sampling plans for inspection of electronic components and packages, used for qualification and conformance inspection.

What does the EN IEC 60115-8-10:2026 document contain?

EN IEC 60115-8-10:2026 contains Figure 1 for outline and dimensions and Figure 2 for the derating curve. It includes Tables 1 to 13, covering styles and dimensions, climatic categories, ratings, resistance range and tolerance, test severities, solderability conditions, resistance-change limits, temperature-rise limits, and the qualification and quality conformance test schedules.

The annexes add the practical support material that makes the blank detail specification usable in drafting. Annex A lists symbols and abbreviations, Annex B provides visual-examination reference material, Annex C adapts the rules for 0 Ω resistors, and Annex X maps this revision to the prior edition.

Relations

Effective Date
02-Sep-2025
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026

Buy Documents

Standard

EN IEC 60115-8-10:2026

English language (50 pages)
Preview
Preview
e-Library read for
×1 day

Frequently Asked Questions

EN IEC 60115-8-10:2026 is a standard published by CLC. Its full title is "Fixed resistors for use in electronic equipment - Part 8-10: Blank detail specification: Surface mount (SMD) low-power film resistors for assembly on circuit boards, for general electronic equipment, classification level G". This standard covers: IEC 60115-8-10:2026 is applicable to the drafting of detail specifications for surface mount (SMD) low-power film resistors, classified to level G, based on the definition of the product classification levels in IEC 60115‑1:2020, 3.4. This edition includes the following significant technical changes with respect to the previous edition IEC 60115‑8‑1:2014: a) it supports solderability testing for both traditional lead-bearing soldering and up-to-date lead-free soldering, as required; b) it supports the provision of detailed visual acceptance criteria; c) it includes the requirement for a visual examination of the primary and proximity packaging; d) it provides for the inclusion of specific visual acceptance criteria, to be applied in addition to those given in Annex B of the sectional specification IEC 60115‑8:2023.

IEC 60115-8-10:2026 is applicable to the drafting of detail specifications for surface mount (SMD) low-power film resistors, classified to level G, based on the definition of the product classification levels in IEC 60115‑1:2020, 3.4. This edition includes the following significant technical changes with respect to the previous edition IEC 60115‑8‑1:2014: a) it supports solderability testing for both traditional lead-bearing soldering and up-to-date lead-free soldering, as required; b) it supports the provision of detailed visual acceptance criteria; c) it includes the requirement for a visual examination of the primary and proximity packaging; d) it provides for the inclusion of specific visual acceptance criteria, to be applied in addition to those given in Annex B of the sectional specification IEC 60115‑8:2023.

EN IEC 60115-8-10:2026 is classified under the following ICS (International Classification for Standards) categories: 31.040.10 - Fixed resistors. The ICS classification helps identify the subject area and facilitates finding related standards.

EN IEC 60115-8-10:2026 has the following relationships with other standards: It is inter standard links to EN 60115-8-1:2015, EN 60115-1:2023, EN IEC 60286-3:2022, EN 61193-2:2007, EN 60063:2015, EN IEC 61760-1:2026, EN 60062:2016, EN IEC 60115-8:2026. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

EN IEC 60115-8-10:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-2026
Nadomešča:
SIST EN 60115-8-1:2015
Fiksni upori za uporabo v elektronski opremi - 8-10. del: Neizpolnjena podrobna
specifikacija - Površinsko montirani (SMD) tankoplastni upori nizke moči za
montažo na tiskana vezja, za univerzalno elektronsko opremo, razvrstitvena raven
G (IEC 60115-8-10:2026)
Fixed resistors for use in electronic equipment - Part 8-10: Blank detail specification:
Surface mount (SMD) low-power film resistors for assembly on circuit boards, for general
electronic equipment, classification level G (IEC 60115-8-10:2026)
Festwiderstände zur Verwendung in Geräten der Elektronik - Teil 8-10: Vordruck für
Bauartspezifikation - Oberflächenmontierbare (SMD) Schicht-Festwiderstände niedriger
Belastbarkeit für Geräte der Elektronik, Klassifikationsstufe G (IEC 60115-8-10:2026)
Résistances fixes utilisées dans les équipements électroniques - Partie 8-10:
Spécification particulière-cadre: Résistances à couche, à faible dissipation, pour
montage en surface (CMS) pour assemblage sur cartes de circuit imprimé pour des
équipements électroniques généraux, niveau de classification G (IEC 60115-8-10:2026)
Ta slovenski standard je istoveten z: EN IEC 60115-8-10:2026
ICS:
31.040.10 Fiksni upor Fixed resistors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 60115-8-10

NORME EUROPÉENNE
EUROPÄISCHE NORM October 2026
ICS 31.040.10 Supersedes EN 60115-8-1:2015
English Version
Fixed resistors for use in electronic equipment - Part 8-10: Blank
detail specification: Surface mount (SMD) low-power film
resistors for assembly on circuit boards, for general electronic
equipment, classification level G
(IEC 60115-8-10:2026)
Résistances fixes utilisées dans les équipements Festwiderstände zur Verwendung in Geräten der Elektronik
électroniques - Partie 8-10: Spécification particulière-cadre: - Teil 8-10: Vordruck für Bauartspezifikation -
Résistances à couche, à faible dissipation, pour montage Oberflächenmontierbare (SMD) Schicht-Festwiderstände
en surface (CMS) pour assemblage sur cartes de circuit niedriger Belastbarkeit für Geräte der Elektronik,
imprimé pour des équipements électroniques généraux, Klassifikationsstufe G
niveau de classification G (IEC 60115-8-10:2026)
(IEC 60115-8-10:2026)
This European Standard was approved by CENELEC on 2026-10-23. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60115-8-10:2026 E

European foreword
The text of document 40/3264/CDV, future edition 1 of IEC 60115-8-10, prepared by TC 40
"Capacitors and resistors for electronic equipment" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN IEC 60115-8-10:2026.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2027-10-31
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2029-10-31
document have to be withdrawn
This document supersedes EN 60115-8-1:2015 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60115-8-10:2026 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 60068-1 NOTE Approved as EN 60068-1
IEC 60068-2-1 NOTE Approved as EN IEC 60068-2-1
IEC 60068-2-2 NOTE Approved as EN IEC 60068-2-2
IEC 60068-2-6 NOTE Approved as EN 60068-2-6
IEC 60068-2-13 NOTE Approved as EN IEC 60068-2-13
IEC 60068-2-14 NOTE Approved as EN IEC 60068-2-14
IEC 60068-2-20 NOTE Approved as EN IEC 60068-2-20
IEC 60068-2-21 NOTE Approved as EN IEC 60068-2-21
IEC 60068-2-30 NOTE Approved as EN IEC 60068-2-30
IEC 60068-2-45 NOTE Approved as EN 60068-2-45
IEC 60068-2-58 NOTE Approved as EN 60068-2-58
IEC 60068-2-78 NOTE Approved as EN IEC 60068-2-78
IEC 60195 NOTE Approved as EN 60195
IEC 60695-11-5 NOTE Approved as EN 60695-11-5
IEC 60749-26 NOTE Approved as EN IEC 60749-26
IEC 80000 series NOTE Approved as EN IEC 80000 series
ISO 80000-5 NOTE Approved as EN ISO 80000-5
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60062 2016 Marking codes for resistors and capacitors EN 60062 2016
IEC 60063 - Preferred number series for resistors and EN 60063 -
capacitors
IEC 60115-1 (mod) 2020 Fixed resistors for use in electronic EN 60115-1 2023
equipment - Part 1: Generic specification
IEC 60115-8 2023 Fixed resistors for use in electronic EN IEC 60115-8 2026
equipment - Part 8: Sectional specification:
Fixed surface mount resistors
+ A11 2026
bIEC 60115-8-10 2026 Fixed resistors for use in electronic EN IEC 60115-8-10 2026
equipment - Part 8-10: Blank detail
specification: Surface mount (SMD) low-
power film resistors for assembly on circuit
boards, for general electronic equipment,
classification level G
IEC 60286-3 - Packaging of components for automatic EN IEC 60286-3 -
handling - Part 3: Packaging of surface
mount components on continuous tapes
IEC 61193-2 2007 Quality assessment systems - Part 2: EN 61193-2 2007
Selection and use of sampling plans for
inspection of electronic components and
packages
IEC 61760-1 - Surface mounting technology - Part 1: EN IEC 61760-1 -
Standard method for the specification of
surface mounting components (SMDs)

IEC 60115-8-10 ®
Edition 1.0 2026-09
INTERNATIONAL
STANDARD
Fixed resistors for use in electronic equipment -
Part 8-10: Blank detail specification: Surface mount (SMD) low-power film
resistors for assembly on circuit boards, for general electronic equipment,
classification level G
ICS 31.040.10  ISBN 978-2-8327-1483-6

IEC 60115-8-10:2026-09(en)
IEC 60115-8-10:2026 © IEC 2026
CONTENTS
FOREWORD. 4
INTRODUCTION . 6
0 Introduction to the template provided by this blank detail specification . 6
0.1 Scope of this blank detail specification . 6
0.2 Function of this blank detail specification . 6
0.3 Identification of the detail specification and the resistor . 7
1 Scope . 9
2 Normative references . 9
3 Terms and definitions . 10
4 Characteristics and ratings . 10
4.1 General . 10
4.2 Dimensions . 10
4.3 Ratings . 12
4.4 Resistance range and tolerance on resistance . 13
5 Tests and test severities . 14
5.1 General . 14
5.2 Resistance . 14
5.3 Temperature coefficient of resistance . 14
5.4 Temperature rise . 14
5.5 Endurance at the rated temperature 70 °C . 15
5.6 Endurance at a maximum temperature: UCT . 15
5.7 Short-term overload . 15
5.8 Electrostatic discharge (ESD) test . 15
5.9 Visual examination . 16
5.10 Gauging of dimensions . 16
5.11 Detail dimensions . 16
5.12 Shear (adhesion) test . 16
5.13 Substrate bending test . 17
5.14 Rapid change of temperature . 17
5.15 Climatic sequence . 17
5.16 Damp heat, steady state . 17
5.17 Solderability, with lead-free solder . 18
5.18 Solderability, with SnPb solder . 18
5.19 Resistance to soldering heat . 18
5.20 Solvent resistance . 19
5.21 Insulation resistance . 19
5.22 Voltage proof . 19
5.23 Flammability . 19
6 Performance requirements . 19
6.1 General . 19
6.2 Limits for change of resistance at tests . 20
6.3 Temperature coefficient of resistance . 20
6.4 Temperature rise . 21
6.5 Visual examination . 21
6.5.1 General visual criteria . 21
6.5.2 Visual criteria after tests . 22
IEC 60115-8-10:2026 © IEC 2026
6.5.3 Visual criteria for packaging . 22
6.6 Solderability . 22
6.7 Insulation resistance . 22
6.8 Flammability . 23
7 Marking, packaging and ordering information . 23
7.1 Marking of the component . 23
7.2 Packaging . 23
7.3 Marking of the packaging . 23
7.4 Ordering information . 23
8 Additional information . 24
8.1 General . 24
8.2 Storage and transportation . 24
8.3 Substrate for assembly . 24
8.4 Soldering process . 24
8.5 Use of cleaning agents or solvents . 25
8.6 Coating or potting after assembly . 25
9 Quality assessment procedures . 25
9.1 General . 25
9.1.1 100 % test . 25
9.1.2 Certificate of conformity (CoC) . 26
9.1.3 Certified test records of released lots . 26
9.2 Qualification approval . 26
9.3 Maintenance of a qualification approval . 26
9.3.1 Quality conformance inspection . 26
9.3.2 Non-conforming specimen . 26
Annex A (normative) Symbols and abbreviated terms . 35
A.1 Symbols . 35
A.2 Abbreviated terms . 38
Annex B (normative) Reference for visual examination . 39
Annex C (normative) 0 Ω resistors (jumpers) . 40
C.1 General . 40
C.2 Characteristics and ratings . 40
C.3 Tests and test severities . 41
C.4 Performance requirements . 41
C.5 Marking, packaging and ordering information . 41
C.6 Additional information . 41
C.7 Quality assessment procedures . 41
C.7.1 Test schedule for qualification approval . 41
C.7.2 Test schedule for quality conformance inspection . 42
Annex D (informative) Cross-references to the prior revision of this specification . 43
Bibliography . 45

Figure 1 – Outline and dimensions . 11
Figure 2 – Derating curve . 13

Table 1 – Styles and dimensions . 11
Table 2 – Climatic categories . 12
IEC 60115-8-10:2026 © IEC 2026
Table 3 – Ratings . 12
Table 4 – Temperature coefficients, tolerances and resistance ranges for climatic
category . / . / . . 13
Table 5 – Short-term overload duration . 15
Table 6 – ESD test voltages . 16
Table 7 – Shear test force . 16
Table 8 – Additional cycles of the damp heat, cyclic test . 17
Table 9 – Damp heat, steady state test duration . 18
Table 10 – Limits for change of resistance at tests . 20
Table 11 – Permitted change of resistance due to the variation of temperature. 21
Table 12 – Test schedule for the qualification approval . 27
Table 13 – Test schedule for quality conformance inspection . 31
Table C.1 – Climatic category . 40
Table C.2 – Ratings for 0 Ω resistors . 40
Table D.1 – Cross-references to clauses of the prior edition . 43
Table D.2 – Cross-references to figures of the prior edition . 44
Table D.3 – Cross-references to tables of the prior edition . 44

IEC 60115-8-10:2026 © IEC 2026
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
Fixed resistors for use in electronic equipment -
Part 8-10: Blank detail specification: Surface mount (SMD)
low-power film resistors for assembly on circuit boards,
for general electronic equipment, classification level G

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which
may be required to implement this document. However, implementers are cautioned that this may not represent
the latest information, which may be obtained from the patent database available at https://patents.iec.ch. IEC
shall not be held responsible for identifying any or all such patent rights.
IEC 60115-8-10 has been prepared by IEC technical committee 40: Capacitors and resistors
for electronic equipment. It is an International Standard.
This edition includes the following significant technical changes with respect to the previous
edition IEC 60115-8-1:2014:
a) it supports solderability testing for both traditional lead-bearing soldering and up-to-date
lead-free soldering, as required;
b) it supports the provision of detailed visual acceptance criteria;
c) it includes the requirement for a visual examination of the primary and proximity packaging;
d) it provides for the inclusion of specific visual acceptance criteria, to be applied in addition
to those given in Annex B of the sectional specification IEC 60115-8:2023.
IEC 60115-8-10:2026 © IEC 2026
The text of this International Standard is based on the following documents:
Draft Report on voting
40/3264/CDV 40/3309/RVC
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
A list of all parts in the IEC 60115 series, published under the general title Fixed resistors for
use in electronic equipment, can be found on the IEC website.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
– reconfirmed,
– withdrawn, or
– revised.
IEC 60115-8-10:2026 © IEC 2026
INTRODUCTION
0 Introduction to the template provided by this blank detail specification
COMMENT This introduction is not intended to be copied into the drafted detail specification. Therefore, it is
positioned in front of the conventional document structure and clause numbering range. It nevertheless contains
normative requirements to the drafted detail specification.
0.1 Scope of this blank detail specification
This part of IEC 60115-8 is applicable to the drafting of detail specifications for surface mount
(SMD) low-power film resistors, classified to level G, based on the definition of the product
classification levels in IEC 60115-1:2020, 3.4.
Another part of IEC 60115-8 provides a separate blank detail specification for the drafting of
detail specifications for surface mount (SMD) low-power film resistors, classified to level P and
to level R.
Yet other parts of IEC 60115-8 may be issued to provide blank detail specifications for the
drafting of detail specifications for surface mount (SMD) resistors, of other technologies or of
other classification levels.
0.2 Function of this blank detail specification
A blank detail specification is a supplementary document to the sectional specification and
contains requirements for style, layout and minimum contents of detail specifications. Detail
specifications not complying with these requirements shall not be accepted as being in
accordance with IEC specifications nor shall they be described as such.
Detail specifications complying with the requirements of this blank detail specification are a
legitimate basis for the quality assessment of leaded fixed low-power film resistors under an
adequate quality assessment system, e.g. the IEC Quality Assessment System for Electronic
Components (IECQ System), whereas the plain blank detail specification is not a suitable basis.
The detail specification should contain a table of contents prior the first page of the actual
specification.
In the preparation of the detail specification, the content of IEC 60115-8:2023, 8.2 shall be
taken into account. The detail specification should be written by using the preferred values
given in IEC 60115-8.
Units, graphical symbols and letter symbols shall, whenever possible, be taken from those
prescribed by the following standards:
– IEC 60027-1, Letter symbols to be used in electrical technology - Part 1: General
– IEC 60617, Graphical symbols for diagrams
– IEC 80000 (all parts), Quantities and units
– ISO 80000 (all parts), Quantities and units
IEC 60115-8-10:2026 © IEC 2026
This blank detail specification uses for its purpose two different kinds of notes:
– NOTE For notes which give additional information intended to assist the
understanding or use of the resulting document and therefore shall be copied
as NOTE into the drafted detail specification. As outlined in the ISO/IEC
directives, these notes shall not contain any requirement, instruction,
recommendation or permission.
– COMMENT For editorial notes which are intended to aid and direct the specification
writer and therefore shall not be copied into the drafted detail specification.
In order to accomplish their function, editorial notes require the use of
instructions, recommendations and permissions addressed to the writer of
the detail specification.
0.3 Identification of the detail specification and the resistor
The first page of the detail specification should have a layout starting with a title block as
recommended on the following page.
The numbers in square brackets are editorial references, which are not intended to be copied
into the drafted detail specification, and which correspond to the following information on the
contents which shall be inserted in the indicated fields.
[1] The name of the standardisation organisation under whose authority the detail specification
is published and, if applicable, the organization from whom the detail specification is
available.
[2] The number allocated to the detail specification by the IEC or by the responsible
standardisation organisation, together with the date of issue and issue number, as
applicable. Further reference details required by the responsible standardisation
organisation or quality assessment system may be given here, including an established
mark of conformity, as applicable.
[3] The number and issue date and number, as applicable, of the relevant generic specification,
sectional specification and blank detail specification, where the referenced issues shall be
the most recent issues of the respective specifications.
[4] The title of the detail specification, providing a short description of the type of resistors.
This entry should support the discrimination between similar specifications and should be
suitable for an entry in a register of approvals or in a catalogue of standards. It may duplicate
information given in fields [6] and [7] and in the textual scope in Clause 1.
[5] An outline drawing or illustration of the products. This entry should aid the easy recognition
of the specified resistors and, if possible, support the discrimination between similar
specifications. It may duplicate information given in Figure 1.
[6] Information on the typical construction of the resistors (where applicable), information of the
specified resistors being insulated or non-insulated (see IEC 60115-1:2020, 3.1.7), and
information on compatibility with a specific soldering process (if applicable, see 8.4). This
entry may duplicate information given in the textual scope in Clause 1.
[7] The classification level of the resistors covered by this detail specification, the level of
quality assessment (Assessment level EZ), and the general level of stability requirements
at performance tests (Stability class).
This information may duplicate information given in the textual scope in Clause 1.
[8] Optional field for table notes.
[9] Statement(s) about the availability of information on components qualified to this detail
specification, if applied within a full quality assessment system.
Example for the use within the IECQ system:
Information about components qualified to this detail specification is available in the
approvals section of the website http://www.iecq.org.
IEC 60115-8-10:2026 © IEC 2026
Specification available from: IEC 60115-8-10xx:20yy
[1] [2]
Electronic components of assessed quality in accordance with:
Generic specification: IEC 60115-1:2020 [3]
Sectional specification: IEC 60115-8:2023
Blank detail specification: IEC 60115-8-10:2026
FIXED RESISTORS FOR USE IN ELECTRONIC EQUIPMENT –
Part 8-10xx: Detail specification – Surface mount (SMD) low-power film resistors for assembly on circuit
boards, …, for general electronic equipment, classification level G
[4]
Technology …
[6]
Insulated / Non-insulated
[5] Termination plating …
Product classification level G
Assessment level EZ [7]
Stability classes .
[8]
COMMENT The remainder of this page is intentionally left empty in order to start Clause 1 on top of the next page.
Information about components qualified to this detail specification is available ….
[9]
IEC 60115-8-10:2026 © IEC 2026
Fixed resistors for use in electronic equipment -
Part 8-10: Blank detail specification: Surface mount (SMD)
low-power film resistors for assembly on circuit boards,
for general electronic equipment, classification level G

COMMENT The above title without the introductory word "blank" is to become the title of the intended detail
specification, which is drafted on the basis of this blank detail specification.
The actual title of the intended detail specification should hold some wording descriptive for the particular kind of
components covered therein, where indicated by "…", in order to support the differentiation between parallel detail
specification on the same level. An example for such descriptive wording would be: "rectangular shape, stability
classes 0,1; 0,25".
1 Scope
COMMENT The text of this clause may repeat information already given in some fields of the above title block.
Essential information on the special type of components covered by the drafted detail specification may be added,
preferably at the place marked with "…".
This detail specification specifies the characteristics and ratings of surface mount (SMD) film
resistors for use in electronic equipment, which are typically assembled on the surface of circuit
boards.
...
The resistors covered herein are classified to level G, as defined in IEC 60115-1:2020, 3.4 for
general electronic equipment, typically operated under benign or moderate environmental
conditions, where the major requirement is function. Examples for level G include consumer
products and telecommunication user terminals.
This detail specification is based upon the blank detail specification IEC 60115-8-10:2026.
This detail specification establishes test schedules and performance requirements permitting
the quality assessment of the resistors covered herein according to the quality assessment
procedures prescribed by IEC 60115-1:2020, Annex Q.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies.
For undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 60062:2016, Marking codes for resistors and capacitors
IEC 60063, Preferred number series for resistors and capacitors
IEC 60115-1:2020, Fixed resistors for use in electronic equipment - Part 1: Generic
specification
IEC 60115-8:2023, Fixed resistors for use in electronic equipment - Part 8: Sectional
specification: Fixed surface mount resistors
IEC 60115-8-10:2026, Fixed resistors for use in electronic equipment - Part 8-10: Blank detail
specification: Surface mount (SMD) low-power film resistors for assembly on circuit boards, for
general electronic equipment, classification level G
IEC 60115-8-10:2026 © IEC 2026
IEC 60286-3, Packaging of components for automatic handling - Part 3: Packaging of surface
mount components on continuous tapes
IEC 61193-2:2007, Quality assessment systems - Part 2: Selection and use of sampling plans
for inspection of electronic components and packages
IEC 61760-1, Surface mounting technology - Part 1: Standard method for the specification of
surface mounting components (SMDs)
...
COMMENT 1 The above list of normative references provides an example and needs to be adapted to the actual
requirements of the drafted detail specification, indicated by the space marked with "…", which however does not
preclude from sorting in proper numerical order.
COMMENT 2 According to the ISO/IEC directives, dated references are required when reference is made to a
specific part of the referenced standard and generally should be applied only in such cases.
COMMENT 3 It is recommended to update any dated references to the most recent revision of the referenced
standard when drafting a detail specification. This involves updating of the dated normative references within the
text of the drafted detail specification.
3 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 60115-1 and in
IEC 60115-8, as well as the following, apply.
ISO and IEC maintain terminology databases for use in standardization at the following
addresses:
– IEC Electropedia: available at https://www.electropedia.org/
– ISO Online browsing platform: available at https://www.iso.org/obp
…
COMMENT Any terms and their respective definitions specifically required for the scope of the drafted detail
specification may be inserted in the space marked with "…", using the prescribed numbering and format. Otherwise,
the above statement should be reduced to "For the purposes of this document, the terms and definitions given in
IEC 60115-1 and in IEC 60115-8 apply." if no further terms or definitions are required in the drafted detail
specification.
4 Characteristics and ratings
4.1 General
Various parameters of this component are precisely defined in this specification. Unspecified
parameters can vary from one component to another.
4.2 Dimensions
The shape and dimensions of the resistors covered by this specification are shown in Figure 1,
with the specific styles and their respective dimensions given in Table 1. Other shapes are
permissible within the given dimensions.
IEC 60115-8-10:2026 © IEC 2026

Figure 1 – Outline and dimensions
COMMENT 1 See IEC 60115-8:2023, 8.2.1.
COMMENT 2 The details shown in Figure 1 may repeat information already given in some fields of the title block
above. Figure 1 in particular needs to define all dimensions intended to be verified by measurements, which generally
includes those dimensions to be prescribed in Table 1.
Table 1 – Styles and dimensions
b
Style Dimensions
Mass
a
L W H Y T m
X
b min
mm mm mm mm mg
a
Historical style code, for information only.
b
For information only.
COMMENT 3 See IEC 60115-8:2023, 8.2.2.
COMMENT 4 The metric style designation is the normative designation used in all other places throughout this
detail specification, see IEC 60115-8:2023, 4.2. Column X is an optional column for additional style information, e.g.
for traditional alphabetic designations, which generally need to be marked with a respective footnote, e.g. as
"Historical style code, for information only".
COMMENT 5 The dimensions for body length L, body width W, body height H and minimum bottom side termination
length T are given as examples based on the requirements for rectangular (RR) and transversal (RT) resistors
b min
and need to correspond to the dimensions identified in Figure 1. The choice of prescribed dimensions needs to be
adapted to the actual requirements of the drafted detail specification and the shape of products covered therein. The
dimensions may be given in the format of nominal values plus tolerance, or by stating permissible minimum and
maximum values. Columns for additional dimensions may be inserted as required.
COMMENT 6 Column Y represents one or more optional column(s) for the prescription of an additional dimension.
COMMENT 7 The component mass is not intended to be verified by an inspection procedure. It should be given as
the maximum mass of a single component and should be marked with a respective footnote as "For information only".
IEC 60115-8-10:2026 © IEC 2026
4.3 Ratings
The climatic categories applied in this detail specification are given in Table 2.
Table 2 – Climatic categories
Climatic category
LCT / UCT / duration
... / ... / ...
... / ... / ...
COMMENT 1 See IEC 60115-8:2023, 8.2.3.
COMMENT 2 Table 2 may be amended with a column showing the key parameter to which different climatic
categories are allocated for the purpose of discrimination, e.g. the applied stability classes.
The upper category temperature (UCT), which is used for test procedures, should be based on
the maximum element temperature (MET).
Table 3 – Ratings
Limiting element voltage Insulation voltage
Style Rated dissipation X
DC or AC RMS DC or AC peak
P U U
70 max ins
mW V V
NOTE The insulation voltage U is verified with a test duration of 1 min. However, long-term insulation properties
ins
can be affected by the influence of moisture, organic material and electrical field across the insulating layer(s).
COMMENT 3 See IEC 60115-8:2023, 8.2.6, IEC 60115-8:2023, 8.2.7 and IEC 60115-8:2023, 8.2.8.
COMMENT 4 Column X is an optional column for additional information, e.g. an additional rated dissipation at
another ambient temperature than the rated temperature 70 °C. Such information should however only be presented
if it is traditionally well-established information.
COMMENT
...