Abstract

This European Standard applies to cold rolled uncoated and electrolytically zinc or zinc-nickel coated low carbon and high yield strength steel flat products for cold forming with a minimum thickness of 0,35 mm and, unless otherwise agreed at the time of ordering, less than or equal to 3 mm thick, delivered in sheet, wide strip, slit wide strip or cut lengths obtained from slit wide strip or sheet. The concerned standards are EN 10130, EN 10152, EN 10271, EN 10209, EN 10268 and prEN 10338.
It does not apply to cold rolled strip (rolled width < 600 mm) or to flat cold rolled products for which there is a specific standard, in particular the following:
   cold rolled non-grain oriented magnetic steel sheet and strip (EN 10106);
   semi-processed steel strip for the construction of magnetic circuits (EN 10126 and 10165);
   tinplate and ECCS (EN 10202);
   blackplate in coils (EN 10205);
cold rolled uncoated non-alloy mild steel narrow strip for cold forming (EN 10139).

Status
Not Published
Publication Date
25-Nov-2027
Current Stage
4020 - Submission to enquiry - Enquiry
Start Date
29-Oct-2026
Due Date
14-Aug-2026
Completion Date
29-Oct-2026

Buy Documents

prEN 10131 is a draft CEN European Standard for cold rolled uncoated and electrolytically zinc or zinc-nickel coated low carbon and high yield strength steel flat products for cold forming. It specifies tolerances on dimensions and shape - including thickness, width, length, flatness, out-of-squareness and edge camber - for buyers, manufacturers and users who order these products as sheet, wide strip, slit wide strip or cut lengths.

What does prEN 10131 specify?

prEN 10131 sets the dimensional and shape tolerances for a defined group of cold rolled steel flat products used for cold forming. It also gives the ordering information needed to apply those tolerances correctly in practice.

The scope covers cold rolled uncoated and electrolytically coated products, including zinc and zinc-nickel coatings, and also names related product families such as low carbon steel, high yield strength steel, vitreous enamelling products, welded gas cylinder strip and multiphase steels. The document also says its tolerances can be used for non-standardized products and for other continuous metallic coatings, except hot-dip coating.

The document is arranged in 12 clauses plus two normative annexes:

AnnexWhat it covers
Annex AThickness tolerances with only positive tolerances
Annex BThickness tolerances with only negative tolerances

Clauses 4 to 12 move from ordering information to supply forms and then to the individual tolerance topics: thickness, width, length, flatness, out-of-squareness, edge camber and superimposition.

What are the key requirements of prEN 10131?

prEN 10131 is mainly an ordering and acceptance document. The key requirements tell the purchaser what to specify, which tolerance class applies, how to measure it, and what happens when no special option is stated.

  • Clause 4 - purchaser information and designation: The order has to state quantity, product form, the reference to EN 10131, nominal thickness, nominal width and, for sheet and cut lengths, nominal length. In practice, this is what links the steel grade to the right tolerance tables and avoids later disputes about what was actually ordered.

  • Clause 4 - optional tolerance choices: The purchaser can request special thickness tolerances (S), width options M, L or S, special length tolerances (S), special flatness tolerances (FS), special camber tolerances (CS), or transposed thickness tolerances from Annex A or Annex B. If nothing is stated, the normal tolerances apply. That matters because the default delivery condition is not the same as a tighter customer-specific order.

  • Clause 5 - forms of supply: The document allows normal or special tolerances on thickness, width, length, flatness and camber, depending on product form. It also states that, if the order gives no delivery-condition details, the product is supplied with normal tolerances on thickness, width, length, flatness and camber.

  • Clause 6 - thickness control: Thickness is measured along the length so coil variation can be checked, and the measurement position must be more than 40 mm from the edges, or at the middle axis for very narrow slit coils or cut lengths. The correct table is selected from Tables 1 to 4 according to the steel's specified minimum yield strength or proof strength. In practice, this is the main acceptance criterion for coil processing and incoming inspection.

  • Clause 6 - dispute measurement: If there is disagreement, the standard calls for repeated measurements across the width, with edge-distance rules for mill edges and trimmed or slit edges, and a method agreed between manufacturer and customer. The clause also points to EN ISO 3611 as an example for micrometer characteristics. That helps both sides use the same measuring basis when thickness is contested.

  • Clauses 7 and 8 - width and length: Width is measured perpendicular to the product axis, with one set of tolerances for sheet and wide strip of width at least 600 mm and another for sheet and slit wide strip below 600 mm. Length is measured along one long side, and Table 7 applies to all covered products. In practice, width and length control the fit of blanks, cut parts and downstream forming tools.

  • Clause 9 to 12 - flatness and shape: Flatness applies only to sheet, and non-skin passed sheet uses only the normal flatness tolerances. Clauses 10 and 11 limit out-of-squareness and edge camber, while Clause 12 allows the parties to replace those two checks with a superimposition requirement for a perfect rectangle of the ordered width and length. This is useful when the buyer cares about nesting, trimming or panel fit rather than separate edge measurements.

What terms does prEN 10131 define?

  • Nominal (specified) thickness is the ordered thickness of the coated or uncoated product; for coated products it includes both the steel core and the coating.
  • Wide strip is cold rolled steel flat product with a rolling width of at least 600 mm.
  • Slit wide strip is wide strip slit to a width less than 1 200 mm.
  • Special tolerances (S) are tighter ordered tolerance classes used for thickness, width or length, depending on the clause.
  • Flatness tolerances (FS) are the special flatness limits that can be ordered for sheet.
  • Edge camber (CS) and out-of-squareness (u) are shape terms used to control edge alignment and edge curvature on delivered sheet or slit strip.

Who uses prEN 10131?

prEN 10131 is used by steel producers, service centres, distributors, buyers and quality control staff who need to agree and verify dimensional tolerances for cold rolled flat products. It is relevant in supply chains for cold forming, including products used for sheet metal parts, coated steel, low carbon grades, high yield strength grades, welded gas cylinders, vitreous enamelling and multiphase steels. In practice, the standard is used for ordering, inspection, receiving, and resolving disputes about thickness, width, length and shape.

What changed in prEN 10131 from the previous edition?

The European foreword states that prEN 10131 will supersede EN 10131:2006.

Which standards are used with prEN 10131?

prEN 10131 uses EN 10079 for the steel product definitions in Clause 3. The bibliography and scope also name EN 10130, EN 10152, EN 10271, EN 10268:2006+A1, EN 10209, EN 10120 and EN 10338 as related product standards whose grades and delivery conditions are referenced when ordering products to this tolerance standard. EN ISO 3611 is cited as an example reference for micrometer metrological characteristics if that measuring method is used.

What does the prEN 10131 document contain?

prEN 10131 contains the order information rules, supply forms and the tolerance system for thickness, width, length and shape. It gives Tables 1 to 4 for thickness, Tables 5 and 6 for width, Table 7 for length, and Tables 8 and 9 for flatness, plus Figure 1 for out-of-squareness and edge camber.

The document also includes practical measurement guidance for thickness, width, length and flatness, so the limits can be checked in production or on receipt. Annex A and Annex B transpose the thickness tolerances into positive-only or negative-only forms for agreed purchasing cases.

Clause 4 includes worked designation examples, which show how to write an order using product form, nominal dimensions, tolerance options and the steel grade designation.

Relations

Effective Date
29-Jun-2022

Buy Documents

Get Certified

Connect with accredited certification bodies for this standard

Element Materials Technology

Materials testing and product certification.

UKAS United Kingdom Verified

Inštitut za kovinske materiale in tehnologije

Institute of Metals and Technology. Materials testing, metallurgical analysis, NDT.

SA Slovenia Verified

Sponsored listings

Frequently Asked Questions

prEN 10131 is a draft published by the European Committee for Standardization (CEN). Its full title is "Cold rolled uncoated and zinc or zinc-nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming - Tolerances on dimensions and shape". This standard covers: This European Standard applies to cold rolled uncoated and electrolytically zinc or zinc-nickel coated low carbon and high yield strength steel flat products for cold forming with a minimum thickness of 0,35 mm and, unless otherwise agreed at the time of ordering, less than or equal to 3 mm thick, delivered in sheet, wide strip, slit wide strip or cut lengths obtained from slit wide strip or sheet. The concerned standards are EN 10130, EN 10152, EN 10271, EN 10209, EN 10268 and prEN 10338. It does not apply to cold rolled strip (rolled width < 600 mm) or to flat cold rolled products for which there is a specific standard, in particular the following: cold rolled non-grain oriented magnetic steel sheet and strip (EN 10106); semi-processed steel strip for the construction of magnetic circuits (EN 10126 and 10165); tinplate and ECCS (EN 10202); blackplate in coils (EN 10205); cold rolled uncoated non-alloy mild steel narrow strip for cold forming (EN 10139).

This European Standard applies to cold rolled uncoated and electrolytically zinc or zinc-nickel coated low carbon and high yield strength steel flat products for cold forming with a minimum thickness of 0,35 mm and, unless otherwise agreed at the time of ordering, less than or equal to 3 mm thick, delivered in sheet, wide strip, slit wide strip or cut lengths obtained from slit wide strip or sheet. The concerned standards are EN 10130, EN 10152, EN 10271, EN 10209, EN 10268 and prEN 10338. It does not apply to cold rolled strip (rolled width < 600 mm) or to flat cold rolled products for which there is a specific standard, in particular the following: cold rolled non-grain oriented magnetic steel sheet and strip (EN 10106); semi-processed steel strip for the construction of magnetic circuits (EN 10126 and 10165); tinplate and ECCS (EN 10202); blackplate in coils (EN 10205); cold rolled uncoated non-alloy mild steel narrow strip for cold forming (EN 10139).

prEN 10131 is classified under the following ICS (International Classification for Standards) categories: 77.140.50 - Flat steel products and semi-products. The ICS classification helps identify the subject area and facilitates finding related standards.

prEN 10131 has the following relationships with other standards: It is inter standard links to EN 10131:2006. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

prEN 10131 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


SLOVENSKI STANDARD
01-januar-2027
Hladno valjani ploščati proizvodi za hladno oblikovanje, neprevlečeni in pocinkani
ali prevlečeni s cink-nikljem, iz maloogljičnega jekla z veliko napetostjo tečenja -
Mejni odstopki mer in tolerance oblike
Cold rolled uncoated and zinc or zinc-nickel electrolytically coated low carbon and high
yield strength steel flat products for cold forming - Tolerances on dimensions and shape
Kaltgewalzte Flacherzeugnisse ohne Überzug und mit elektrolytischem Zink- oder Zink-
Nickel-Überzug aus weichen Stählen sowie aus Stählen mit höherer Streckgrenze zum
Kaltumformen - Grenzabmaße und Formtoleranzen
Produits plats laminés à froid, non revêtus ou revêtus de zinc ou de zinc-nickel par voie
électrolytique, en acier à bas carbone et en acier à haute limite d'élasticité pour formage
à froid - Tolérances sur les dimensions et sur la forme
Ta slovenski standard je istoveten z: prEN 10131
ICS:
77.140.50 Ploščati jekleni izdelki in Flat steel products and semi-
polizdelki products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2026
ICS Will supersede EN 10131:2006
English Version
Cold rolled uncoated and zinc or zinc-nickel
electrolytically coated low carbon and high yield strength
steel flat products for cold forming - Tolerances on
dimensions and shape
Produits plats laminés à froid, non revêtus ou revêtus Kaltgewalzte Flacherzeugnisse ohne Überzug und mit
de zinc ou de zinc-nickel par voie électrolytique, en elektrolytischem Zink- oder Zink-Nickel-Überzug aus
acier à bas carbone et en acier à haute limite weichen Stählen sowie aus Stählen mit höherer
d'élasticité pour formage à froid - Tolérances sur les Streckgrenze zum Kaltumformen - Grenzabmaße und
dimensions et sur la forme Formtoleranzen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 459/SC 9.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 10131:2026 E
worldwide for CEN national Members.

Page
Contents
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Information to be supplied by the purchaser . 4
4.1 General . 4
4.2 Options . 5
4.3 Designation . 5
5 Forms of supply . 5
6 Tolerances on thickness . 6
7 Tolerances on width . 9
7.1 General . 9
7.2 Sheet and strip of width ≥ 600 mm . 9
7.3 Sheet and strip of width < 600 mm . 10
8 Tolerances on length . 10
9 Tolerances on flatness . 11
9.1 General . 11
9.2 Steel grades with specified minimum yield strength Re < 260 MPa . 11
9.3 Steel grades with specified minimum yield strength 260 MPa ≤ Re < 340 MPa . 12
9.4 Steel grades with specified minimum yield strength Re ≥ 340 MPa . 12
10 Tolerances on out of squareness . 12
11 Tolerances on edge camber . 12
12 Superimposition of dimensions . 13
Annex A (normative) Thickness tolerances with only positive tolerances according to
5.3 . 14
Annex B (normative) Thickness tolerances with only negative tolerances according to
5.4 . 17
Bibliography. 21

European foreword
This document (prEN 10131:202X) has been prepared by Technical Committee CEN/TC 459/SC 9
"Coated and uncoated flat products to be used for cold forming", the secretariat of which is held by
AFNOR.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 10131:2006.
1 Scope
This document applies to cold rolled uncoated and electrolytically zinc or zinc-nickel coated low carbon
steel products, steel products with high yield strength steel, low carbon steel flat products for vitreous
enamelling, sheet and strip for welded gas cylinders and multiphase steel flat products for cold forming
with a minimum thickness of 0,20 mm and, unless otherwise agreed at the time of ordering, less than or
equal to 3 mm thick, delivered in sheet, wide strip , slit wide strip or cut lengths obtained from slit wide
strip or sheet. The concerned standards are EN 10130 [1], EN 10152 [2], EN 10271 [3], EN
10268:2006+A1 [4], EN 10209 [5] and cold rolled products in EN 10120 [6] and EN 10338 [7].
The tolerances of this document can also be used for deliveries of non-standardized products.
It also applies to other cold rolled steel flat products with metallic coatings applied in other continuous
processes, e.g. jet vapour deposition, except for hot-dip coating.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 10079, Definition of steel products
3 Terms and definitions
For the purposes of this document, the following terms and definitions given in EN 10079 and the
following apply.
• ISO Online browsing platform: available at http://www.iso.org/obp
• IEC Electropedia: available at http://www.electropedia.org/
3.1
nominal (specified) thickness
ordered thickness of the coated or uncoated product
Note 1 to entry: In the case of coated products, nominal thickness includes steel core and coating.
3.2
wide strip
cold rolled steel flat products with a rolling width ≥ 600 mm
3.3
slit wide strip
cold rolled steel flat products with a rolling width ≥ 600 mm, slit to a width less than 1 200 mm
4 Information to be supplied by the purchaser
4.1 General
Products related to this document shall be designated in the following order (see also Clause 5):
a) quantity to be delivered;
b) type of product (sheet, wide strip (3.2) , slit wide strip (3.3) or cut length);
c) reference to this document i.e. EN 10131;
d) nominal thickness (3.1) in millimetres;
e) nominal width in millimetres;
f) nominal length in millimetres (sheets and cut lengths only);
4.2 Options
A number of options are specified in this document and listed below. If the purchaser does not indicate
the wish to implement any of these options, the products shall be supplied in accordance with the
normal specification of this document (see 4.1 and 5.1 ).
a) whether the products are to be supplied with special tolerances on thickness, add letter S (see
Clause 6 )
b) whether the products are to be supplied with: - mill edges tolerances on width, add letter M, -
large tolerances on width, add letter L, - special tolerances on width, add letter S (see Clause 7 );
c) whether the products are to be supplied with special tolerances on length (sheets and cut lengths
only), add letter S (see Clause 8);
d) whether the products are to be supplied with special tolerances on flatness, add symbol FS (see
Clause 9);
e) whether the products are to be supplied with special tolerances on camber, add symbol CS (see
Clause 11);
f) whether the products are to be supplied with transposed tolerances in accordance with Annex A
or Annex B .
4.3 Designation
The product designation in accordance with 4.1 and 4.2 shall be followed by the complete designation
of the steel ordered (e.g. according to EN 10130 [1] ).
EXAMPLE 1   100 tonnes of wide strip (3.2) according to this document of nominal thickness (3.1) 1,20 mm,
nominal width of 1 500 mm in steel DC04-A-m as specified in EN 10130 [1] :
100 t wide strip (3.2) EN 10131-1,20x1500
Steel EN 10130 [1] -DC04-A-m
EXAMPLE 2   50 sheets according to this document of nominal thickness (3.1) 0,80 mm ordered with special
thickness tolerance (S), nominal width of 1 200 mm with special tolerances on width (S), nominal length of 2 500
mm and with special tolerances on flatness (FS) in steel DC06-B-g as specified in EN 10130 [1] :
50 sheets EN 10131-0,80Sx1200Sx2500FS
Steel EN 10130 [1] -DC06-B-g
EXAMPLE 3   30 tonnes of wide strip (3.2) according to this document of nominal thickness (3.1) 0,80 mm
ordered with transposed tolerances on the positive side, nominal width of 1000 mm with large tolerances on width
(L) in steel HC340LA as specified in EN 10268:2006+A1 [4] :
30 t wide strip (3.2) EN 10131 0,80x1000L with thickness tolerances from Annex A
Steel EN 10268:2006+A1 [4] -HC340LA
5 Forms of supply
5.1 Flat products according to this document may be delivered as follows:
a) with normal or special thickness tolerances (see Table 1, Table 2, Table 3 and Table 4);
b) with mill edges, large, normal or special width tolerances (see Table 5 and Table 6);
c) with normal or special length tolerances for sheet or cut lengths (see Table 7);
d) with normal or special flatness tolerances for sheet or cut lengths (see Table 8 and Table 9);
e) with normal or special tolerances on camber for slit strip of width less than 600 mm (see Clause
11).
5.2 In the absence of information on the order in respect of the condition of delivery given in 5.1 the
flat products shall be delivered with normal tolerances on thickness, width, length, flatness and camber.
5.3 Whether the minimum thickness of the product shall be the nominal thickness (3.1) and the full
range of the thickness tolerance from Table 1, Table 2, Table 3 and Table 4 (transposition of tolerances)
shall be valid only as a positive tolerance, manufacturer and purchaser may agree that only positive
thickness tolerances apply. These transposed thickness tolerances are given in Annex A, see Table A.1,
Table A.2, Table A.3 and Table A.4 .
5.4 Whether the maximal thickness of the product shall be the nominal thickness (3.1) and the full
range of the thickness tolerance from Table 1, Table 2, Table 3 and Table 4 (transposition of tolerances)
shall be valid only as a negative tolerance, manufacturer and purchaser may agree that only negative
thickness tolerances apply. These transposed thickness tolerances are given inAnnex B, see .Table B.1 ,
Table B.2 , Table B.3 and Table B.4
6 Tolerances on thickness
The thickness shall be measured along the length so that its variation along the coil can be determined.
Thickness variation over the strip width is controlled by restricting the thickness profile of hot rolled
strip.
NOTE 1   There are two examples for used measurement methods for measuring the thickness of steel strip:
- Radio absorption measurement (X-ray or Isotope) determines the mass per surface area via radiation absorption
and calculates the thickness using the material density. Characteristics of these measurement methods include:
high accuracy, suitability for closed-loop control systems, works well with oil/emulsion or coatings, and high strip
speed. For a stable measurement, the variation in the source's strength over time and the dependence of
absorption depends on the steel type. Regular calibration of the measurement with calibration plates exists.
- Laser optical thickness measurement measures geometric distance between the top and bottom of the strip using
laser triangulation This measurement is characterized by: high resolution, sensitive to vibrations/oil, especially
suitable for thin strip/foil, often applied near finishing or coating lines.
The position of the measurement shall be located more than 40 mm from the edges.
In the case of slit coils or cut lengths having a width of 80 mm or below, the position of the measurement
shall be at the middle axis.
The tolerances on thickness shall be as given in Table 1, Table 2, Table 3 and Table 4 and apply over the
whole length.
The correct Table 1, Table 2, Table 3 or Table 4 shall be selected in accordance with the specified
minimum yield strength or proof strength of the steel grade in question.
NOTE 2   Depending on the steel grade, the material can show a pronounced yield phenomenon and have a
yield strength or it is characterized by a proof strength.
The thickness tolerances of steel grades in EN 10130 [1] and EN 10152 [2] are specified in Table 1 .
Tolerances tighter than special tolerances may be agreed at the time of enquiry and order.
In the event of a dispute, a sample sheet should be measured at least three times across the width of the
strip. The minimum distance from the edge should be at least 40 mm for mill edges and at least 25 mm
for trimmed/slit edges. A method with sufficient accuracy, relative to the thickness tolerance of the
supplied strip, shall be agreed between manufacturer and customer. As example, a micrometer can be
used for this purpose (See EN ISO 3611 [8] ).
Table 1 — Tolerances on thickness for steel grades with a specified minimum yield strength R
e
a
< 260 MPa
Dimensions in millimetres
b b
nominal Normal tolerances for a nominal width w Special tolerances (S) for a nominal width w
thickness
(3.1)
≤ 1 200 > 1 200 to ≤ > 1 500 ≤ 1 200 > 1 200 to ≤ > 1 500
1 500 1 500
= 0,20 to ± 0,03 ± 0,04 ± 0,05 ± 0,020 ± 0,025 ± 0,030
0,40
> 0,40 to ± 0,03 ± 0,04 ± 0,05 ± 0,025 ± 0,030 ± 0,035
0,60
> 0,60 to ± 0,04 ± 0,05 ± 0,06 ± 0,030 ± 0,035 ± 0,040
0,80
> 0,80 to ± 0,05 ± 0,06 ± 0,07 ± 0,035 ± 0,040 ± 0,050
1,00
> 1,00 to ± 0,06 ± 0,07 ± 0,08 ± 0,040 ± 0,050 ± 0,060
1,20
> 1,20 to ± 0,08 ± 0,09 ± 0,10 ± 0,050 ± 0,060 ± 0,070
1,60
> 1,60 to ± 0,10 ± 0,11 ± 0,12 ± 0,060 ± 0,070 ± 0,080
2,00
> 2,00 to ± 0,12 ± 0,13 ± 0,14 ± 0,080 ± 0,090 ± 0,100
2,50
> 2,50 to ± 0,15 ± 0,15 ± 0,16 ± 0,100 ± 0,110 ± 0,120
3,00
a 2
1 MPa = 1 N/mm
b
The thickness tolerances in the region of cold rolled welds may be increased by a maximum of 50 % over
a length of 10 metres. This increase is applicable to all thicknesses and, unless otherwise agreed at the time of
enquiry and order, to normal and special tolerances over or under.

Table 2 — Tolerances on thickness for steel grades with a specified minimum yield strength
a
260 MPa ≤ R < 340 MPa
e
Dimensions in millimetres
b b
nominal Normal tolerances for a nominal width w Special tolerances (S) for a nominal width w
thickness
(3.1)
≤ 1 200 > 1 200 to ≤ > 1 500 ≤ 1 200 > 1 200 to ≤ > 1 500
1 500 1 500
= 0,20 to ± 0,04 ± 0,05 ± 0,06 ± 0,025 ± 0,030 ± 0,035
0,40
> 0,40 to ± 0,04 ± 0,05 ± 0,06 ± 0,030 ± 0,035 ± 0,040
0,60
> 0,60 to ± 0,05 ± 0,06 ± 0,07 ± 0,035 ± 0,040 ± 0,050
0,80
> 0,80 to ± 0,06 ± 0,07 ± 0,08 ± 0,040 ± 0,050 ± 0,060
1,00
> 1,00 to ± 0,07 ± 0,08 ± 0,10 ± 0,050 ± 0,060 ± 0,070
1,20
> 1,20 to ± 0,09 ± 0,11 ± 0,12 ± 0,060 ± 0,070 ± 0,080
1,60
> 1,60 to ± 0,12 ± 0,13 ± 0,14 ± 0,070 ± 0,080 ± 0,100
2,00
> 2,00 to ± 0,14 ± 0,15 ± 0,16 ± 0,100 ± 0,110 ± 0,120
2,50
> 2,50 to ± 0,17 ± 0,18 ± 0,18 ± 0,120 ± 0,130 ± 0,140
3,00
a 2
1 MPa = 1 N/mm
b
The thickness tolerances in the region of cold rolled welds may be increased by a maximum of 50 % over
a length of 10 metres. This increase is applicable to all thicknesses and, unless otherwise agreed at the time of
enquiry and order, to normal and special tolerances over or under.

Table 3 — Tolerances on thickness for steel grades with a specified minimum yield strength
a
340 MPa ≤ R < 420 MPa
e
Dimensions in millimetres
b b
nominal Normal tolerances for a nominal width w Special tolerances (S) for a nominal width w
thickness
(3.1)
≤ 1 200 > 1 200 to ≤ > 1 500 ≤ 1 200 > 1 200 to ≤ > 1 500
1 500 1 500
= 0,35 to ± 0,04 ± 0,05 ± 0,
...