EN 12629-4:2001/FprA1

SLOVENSKI STANDARD
01-april-2010
6WURML]DL]GHODYRJUDGEHQLKSURL]YRGRYL]EHWRQDLQDSQHQHJDSHãþHQFD9DUQRVW
GHO6WURML]DL]GHODYREHWRQVNLKVWUHãQLNRY
Machines for the manufacture of constructional products from concrete and calcium-
silicate - Safety - Part 4: Concrete roof tile making machines
Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen -
Sicherheit - Teil 4: Beton-Dachsteinmaschinen
Machines pour la fabrication de produits de construction en béton et silico-calcaire -
Sécurité - Partie 4: Machines pour la fabrication de tuiles en béton
Ta slovenski standard je istoveten z: EN 12629-4:2001/FprA1
ICS:
91.220 Gradbena oprema Construction equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
FINAL DRAFT
EN 12629-4:2001
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
February 2010
ICS 91.220
English Version
Machines for the manufacture of constructional products from
concrete and calcium-silicate - Safety - Part 4: Concrete roof tile
making machines
Machines pour la fabrication de produits de construction en Maschinen für die Herstellung von Bauprodukten aus Beton
béton et silico-calcaire - Sécurité - Partie 4: Machines pour und Kalksandsteinmassen - Sicherheit - Teil 4: Beton-
la fabrication de tuiles en béton Dachsteinmaschinen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 151.
This draft amendment A1, if approved, will modify the European Standard EN 12629-4:2001. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12629-4:2001/FprA1:2010: E
worldwide for CEN national Members.

Contents Page
Foreword .3
1 Modifications to the Foreword .4
2 Modifications to the Introduction .5
3 Modifications to Clause 1 (Scope) .5
4 Modifications to Clause 2 (Normative references) .6
5 Modifications to Clause 3 (Definitions) .6
6 Modifications to Clause 4 (List of significant hazards) .6
7 Modifications to Clause 5 (Safety requirements and/or measures) .7
8 Modifications to Clause 6 (Verification of safety requirements and/or measures) .7
9 Modifications to Clause 7 (Instructions for use) .8
10 Modifications to Clause 8 (Warnings).8
11 Modifications to Clause 9 (Marking) .8
12 Modifications to Annex A (First typical concrete tile manufacturing plant) .8
13 Modifications to Annex B (Second typical concrete tile manufacturing plant) .8
14 Modification to Annex ZA, Relationship between this European Standard and the
Essential Requirements of EU Directive 98/37/EC .9
15 Addition of a new Annex ZB, Relationship between this European Standard and the
Essential Requirements of EU Directive 2006/42/EC .9
16 Modification to the Bibliography . 10

Foreword
This document (EN 12629-4:2001/FprA1:2010) has been prepared by Technical Committee CEN/TC 151
“Construction equipment and building material machines - Safety”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annexes ZA and B, which are integral parts of this
document.
1 Modifications to the Foreword
th
Replace the 4 paragraph with the following:
"For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document."
th th
Delete the 5 and 6 paragraphs.
th
Replace the 7 paragraph with the following:
"The series "Machines for the manufacture of constructional products from concrete and calcium – silicate –
Safety" consists of following parts:
Part 1: Common requirements
Part 2: Block making machines
Part 3: Slide and turntable machines
Part 4: Concrete rooftile making machines
Part 5.1: Concrete pipe machines manufacturing in the vertical axis.
Part 5.2: Concrete pipe machines manufacturing in the horizontal axis
Part 5.3: Pipe prestressing machines
Part 5.4: Concrete pipe coating machines
Part 6: Stationary and mobile equipment for the manufacture of precast reinforced products
Part 7: Stationary and mobile equipment for the benched manufacture of prestressed products
Part 8: Machines and equipment for the manufacture of constructional products from calcium silicate (and
concrete)."
2 Modifications to the Introduction
Replace the existing text with the following:
"This European Standard is a Type C-standard as stated in EN ISO 12100.
The machinery concerned and the extent to which hazards, hazardous situation and events are covered are
indicated in the scope of this document.
When provisions of this type C document are different from those, which are stated in type A or B documents,
the provisions of this type C document take precedence over the provisions of the other documents, for
machines that have been designed and built according to the provisions of this type C document.
This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1:2010
specific for the concrete roof tile making machines as described in 1.1.
With the aim of clarifying the intentions of the document it should be noticed that the following assumptions
were made when producing it:
 specific conditions of use or environmental conditions out of the scope of the document shall be the
subject of negotiations between the manufacturer and the user/owner,
 the equipment will only be used by competent and designated persons,
 the place of u
...