EN 14023:2005

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bitumen in bitumenska veziva – Okvirna specifikacija za bitumne, modificirane s polimeriBitumen und bitumenhaltige Bindemittel - Rahmenwerk für die Spezifikation von polymermodifizierten BitumenBitumes et liants bitumineux - Cadre de spécifications des bitumes modifiés par des polymeresBitumen and bituminous binders - Framework specification for polymer modified bitumens91.100.50Veziva. Tesnilni materialiBinders. Sealing materials75.140Voski, bitumni in drugi naftni proizvodiWaxes, bituminous materials and other petroleum productsICS:Ta slovenski standard je istoveten z:EN 14023:2005SIST EN 14023:2005en01-december-2005SIST EN 14023:2005SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14023October 2005ICS 93.080.20 English VersionBitumen and bituminous binders - Framework specification forpolymer modified bitumensBitumes et liants bitumineux - Cadre de spécifications desbitumes modifiés par des polymèresBitumen und bitumenhaltige Bindemittel - Rahmenwerk fürdie Spezifikation von polymermodifizierten BitumenThis European Standard was approved by CEN on 24 February 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2005 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14023:2005: ESIST EN 14023:2005

Example of selected classes for a PMB 45/80-60.16 Annex B (informative)
Other characteristics.17 Annex ZA (informative)
Clauses of this European Standard addressing essential requirements or other provisions of EU Directives.18 ZA.1 Scope and relevant characteristics.18 ZA.2 Procedure for attestation of conformity of polymer modified bitumens.19 ZA.3 CE marking and labelling.21 Bibliography.24
Bituminous Binders Paving ApplicationsIndustrial ApplicationsPaving Grade
Bitumens
EN 12591 Polymer Modified Bitumens
EN 14023 Cutback &Fluxed
Bitumens prEN 15322Cationic Bitumen Emulsions EN 13808 Oxidised
Bitumens
EN 13304 Hard Paving Grade
Bitumens
prEN 13924 Hard GradeIndustrialBitumens EN 13305 SIST EN 14023:2005

In Table 2 further characteristics that have been considered useful for specifications are described. SIST EN 14023:2005

1b
2 3 4 5 6 7 8 9 10 Consistency at Intermediate Service Temperature Penetration at 25 °C EN 1426 0,1 mm
TBR 10-40 25-55
45-80
40-100
65-105
75-130
90-150
120-200 200-300 Consistency at Elevated Service Temperature Softening Point EN 1427 °C
TBR ≥ 80
≥ 75
≥ 70
≥ 65 ≥ 60 ≥ 55
≥ 50
≥ 45
≥ 40 Force ductility c
(Low speed traction) or EN 13589 followed by EN 13703 J/cm2 NPD TBR ≥ 3 at 5 °C ≥2 at 5°C ≥ 1 at 5°C ≥ 2
at 0°C ≥ 2 at 10°C - - - - Tensile test at 5 °C c (High speed traction) or EN 13587 followed by EN 13703 J/cm2 NPD TBR ≥ 3 ≥ 2 ≥ 1 - - - - - - Cohesionc
Vialit pendulum c
(Impact test) EN 13588 J/cm2 NPD TBR ≥ 0,7 - - - - - - - - Change of mass
EN 12607-1 EN 12607-3 % NPD TBR ≤ 0,3 ≤ 0,5 ≤ 0,8 ≤ 1,0 - - - - - Retained Penetration
EN 1426 % NPD TBR ≥ 35 ≥ 40 ≥ 45 ≥ 50 ≥ 55 ≥ 60 - - - Durabilityd
(Resistance to hardening, EN 12607-1
or -3) Increase in Softening Point
EN 1427 °C NPD TBR ≤ 8 ≤ 10 ≤ 12 - - - - - - Other characteristics Flash Point e
EN ISO 2592 °C
≥ 250 ≥ 235 ≥ 220 - - - - - - SIST EN 14023:2005

UNIT 0 1 a 2 3 4 5 6 7 8 9 10 Fraass Breaking Point EN 12593 °C NPD TBR
...