Abstract

This part of the EN 13451 series specifies safety requirements for diving platforms, diving springboards and associated equipment in addition to the general safety requirements of EN 13451-1 and is meant to be read in conjunction with it.
The requirements of this part of the EN 13451 series take priority over those in EN 13451-1.
This part of the EN 13451 series is applicable to platforms and springboards, and associated equipment for use in classified swimming pools as specified in EN 15288-1 and EN 15288-2.

Status
Published
Publication Date
06-Oct-2026
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
07-Oct-2026
Due Date
20-Nov-2028
Completion Date
07-Oct-2026

Buy Documents

Standard

EN 13451-10:2018+A1:2026

English language (26 pages)
Preview
Preview
e-Library read for
×1 day

EN 13451-10:2018+A1:2026 is a CEN European Standard for swimming pool equipment. It specifies additional safety requirements and test methods for diving platforms, diving springboards and associated equipment, and it is meant to be read with EN 13451-1.

The document is for people who design, manufacture, install, test, specify or operate diving facilities in classified swimming pools. In practice, it tells them what geometry, access, barriers, surfaces and verification tests are needed so the equipment can be selected and checked against one common European basis.

What does EN 13451-10:2018+A1:2026 specify?

EN 13451-10:2018+A1:2026 sets extra safety rules for diving platforms, diving springboards and associated equipment on top of the general safety requirements in EN 13451-1. Its requirements take priority where the two parts overlap, so users do not need to reconcile conflicting provisions.

The standard applies to facilities for use in classified swimming pools as covered by EN 15288-1 and EN 15288-2. It is organized into five clauses: scope, normative references, terms and definitions, safety requirements, and test methods. The bibliography points to supporting diving-facility rules and related pool-equipment standards.

What are the key requirements of EN 13451-10:2018+A1:2026?

Platform and springboard geometry

Clause 4 ties the design to the height and type of the diving facility. The tables and figures set the usable dimensions, clearances, water depths and surrounding space for platforms and for springboards of type 1 and type 2. In practice, this means the designer has to choose the correct facility layout for the intended diving height, not just the equipment itself.

For diving platforms, Clause 4 requires a rigid, horizontal platform with attention to glare and reflecting surfaces that could disturb the diver. The platform front edge has to meet the stated shape and thickness limits, and the facility clearances have to leave enough space around the plummet line and the water zone. This matters because a diver needs a predictable take-off surface and a protected landing area.

For diving springboards, Clause 4 distinguishes type 1 and type 2. Type 2 may be permanent or portable, but portable units have extra installation conditions and adjustable fulcrums are not allowed. The fulcrum position has to be clearly and permanently marked, and the board has to remain horizontal wherever the fulcrum is set. This matters for safe use because the board setting affects bounce, balance and repeatability.

Access and barriers

Clause 4.4 controls access to the diving area. Diving platforms and type 1 springboards shall be reached by stairs, stepladders or ramps, with lifts only where relevant regulations allow them; ladders are not permitted. For type 2 springboards, a low board needs one step and a higher board needs stepladders or stairs. Operators also have to prevent access when the diving facility is closed.

Clause 4.4.2 gives the main rules for stepladders used at diving facilities. The ladder geometry, handrails and tread proportions are specific, and the document points to EN 13451-2 for the parts designed to be gripped. In practice, this gives manufacturers and installers a clear basis for making access equipment that users can climb safely in a wet environment.

Clause 4.5 requires safety barriers for facilities above a stated height above the pool surround. The barriers must follow EN 13451-1, comply with building regulations and be designed to prevent climbing. They may be vertical rails, panels or walls, and they are allowed within clearance zones when they serve as safety devices. For the reader, this means the barrier is not just a boundary - it is part of the overall diving safety layout.

Surfaces, water zones and special equipment

Clause 4.6 sets slip-resistance expectations for the diver’s area, other walkable surfaces and the access routes. The intent is to match the surface grip to the way people move on platforms, boards and approaches. That matters because wet surfaces can turn a normal walk or take-off into a slip hazard.

Clause 4.7 requires the water diving zones for platforms and springboards to match the geometry given elsewhere in the standard, and it requires adjacent diving zones and multifunctional pool activities to be separated during use. Clause 4.8 says water-surface agitation devices must not interfere with dives, and any in-pool water or air fittings have to comply with EN 13451-3. Clause 4.9 adds requirements for air cushion equipment, including installation depth, operator position, indicators and control of the air-cushion cycle.

Verification and testing

Clause 5 says that requirements are verified by measurement, visual examination or practical tests unless a different method is specified. It then gives structural integrity tests for springboards, stepladders and safety barriers. In practice, the standard is not just a design document - it also tells you how to check that the installed equipment behaves as intended.

What terms does EN 13451-10:2018+A1:2026 define?

  • Diving facility - an installation designed to provide the opportunity of diving.
  • Diving platform - a raised rigid horizontal platform extending over the water for diving.
  • Diving springboard type 1 - a raised flexible board above 1.0 m and up to 3.05 m above water level for diving.
  • Diving springboard type 2 - a raised flexible board below 1.0 m above water level, which may be permanent or portable, for recreational diving.
  • Plummet line - the vertical line through the centre of the front edge of a platform or springboard.
  • Water agitation device - equipment used to disturb the water surface and improve visibility.
  • Air cushion equipment - a training device that introduces air in front of the diving area to reduce impact effects and support safer training.

Who uses EN 13451-10:2018+A1:2026?

EN 13451-10:2018+A1:2026 is used by diving-facility manufacturers, pool designers, installers, operators and inspection bodies. It is also relevant to buyers and quality managers who need to define acceptance criteria for platforms, springboards, access systems and safety barriers.

Its main practical use is in public and classified swimming pools where diving equipment has to be selected, installed and checked against a common safety baseline. It is especially relevant when a pool has multiple uses, because the standard also addresses segregation of diving zones from other users.

What changed in EN 13451-10:2018+A1:2026 from the previous edition?

EN 13451-10:2018+A1:2026 supersedes EN 13451-10:2018. The foreword states that Amendment 1 was added and that the main changes were:

  • the values in Tables 2 and 4 were reviewed and revised where needed against the current Fédération Internationale de Natation (FINA) table;
  • the stepladder clause for diving facilities was revised;
  • the safety-barrier clause was revised;
  • the slip-resistance clause was revised.

Which standards are used with EN 13451-10:2018+A1:2026?

  • EN 13451-1:2011+A1:2016 - supplies the general safety requirements and test methods that this part builds on.
  • EN 13451-3 - contributes requirements for inlets, outlets and water/air-based water leisure features, including fittings used with water or air introduction.
  • EN 22768-1 - provides general tolerances for linear and angular dimensions when no special tolerance is given.
  • EN 15288-1 - defines safety requirements for pool design, which this part uses to limit where it applies.
  • EN 15288-2 - defines safety requirements for pool operation, which also frames the intended use of the diving facilities.
  • EN 13451-2 - is referenced for the dimensions of gripped parts in stepladders.
  • FINA Facilities Rules 2009-2013 - are cited in the bibliography for competitive diving context and related dimensional guidance.

What does the EN 13451-10:2018+A1:2026 document contain?

Clause 4 is supported by Figures 1 to 12 and Tables 1 to 4, which lay out platform and springboard geometry, clearances, water zones, access arrangements and safety barriers. Those figures and tables are the core design reference for determining the usable layout of a diving facility.

Clause 5 contains the test methods. It includes the load tests for type 1 and type 2 springboards, the verification of stepladder treads and handle bends, and the barrier strength test using a horizontal distributed force. The document also explains how compliance is judged after the test loads are applied.

The bibliography points users to FINA rules and related EN standards that support design, installation and surface or access requirements.

Relations

Effective Date
29-Jul-2026
Effective Date
21-Oct-2026
Effective Date
21-Oct-2026
Effective Date
21-Oct-2026
Effective Date
29-Jul-2026
Effective Date
29-Jul-2026
Effective Date
29-Jul-2026
Effective Date
29-Jul-2026
Effective Date
29-Jul-2026

Buy Documents

Standard

EN 13451-10:2018+A1:2026

English language (26 pages)
Preview
Preview
e-Library read for
×1 day

Frequently Asked Questions

EN 13451-10:2018+A1:2026 is a standard published by the European Committee for Standardization (CEN). Its full title is "Swimming pool equipment - Part 10: Additional specific safety requirements and test methods for diving platforms, diving springboards and associated equipment". This standard covers: This part of the EN 13451 series specifies safety requirements for diving platforms, diving springboards and associated equipment in addition to the general safety requirements of EN 13451-1 and is meant to be read in conjunction with it. The requirements of this part of the EN 13451 series take priority over those in EN 13451-1. This part of the EN 13451 series is applicable to platforms and springboards, and associated equipment for use in classified swimming pools as specified in EN 15288-1 and EN 15288-2.

This part of the EN 13451 series specifies safety requirements for diving platforms, diving springboards and associated equipment in addition to the general safety requirements of EN 13451-1 and is meant to be read in conjunction with it. The requirements of this part of the EN 13451 series take priority over those in EN 13451-1. This part of the EN 13451 series is applicable to platforms and springboards, and associated equipment for use in classified swimming pools as specified in EN 15288-1 and EN 15288-2.

EN 13451-10:2018+A1:2026 is classified under the following ICS (International Classification for Standards) categories: 97.220.10 - Sports facilities. The ICS classification helps identify the subject area and facilitates finding related standards.

EN 13451-10:2018+A1:2026 has the following relationships with other standards: It is inter standard links to EN 13451-10:2018, EN 13451-1:2011+A1:2016, EN 13451-3:2022+A1:2025, EN 22768-1:1993, EN 17164:2018, EN 17232:2020, EN 13451-11:2004, EN 13451-4:2025, EN 13451-11:2014. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

EN 13451-10:2018+A1:2026 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-2026
Nadomešča:
SIST EN 13451-10:2018
Oprema za plavalne bazene - 10. del: Dodatne posebne varnostne zahteve in
preskusne metode za odskočne ploščadi, odskočne deske in pripadajočo opremo
(vključno z dopolnilom A1)
Swimming pool equipment - Part 10: Additional specific safety requirements and test
methods for diving platforms, diving springboards and associated equipment
Schwimmbadgeräte - Teil 10: Zusätzliche besondere sicherheitstechnische
Anforderungen und Prüfverfahren für Sprungplattformen, Sprungbretter und zugehörige
Geräte
Équipement de piscine - Partie 10 : Exigences de sécurité et méthodes d’essai
complémentaires propres aux plates-formes de plongeon, aux plongeoirs et à
l’équipement associé
Ta slovenski standard je istoveten z: EN 13451-10:2018+A1:2026
ICS:
97.220.10 Športni objekti Sports facilities
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 13451-10:2018+A1
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2026
EUROPÄISCHE NORM
ICS 97.220.10 Supersedes EN 13451-10:2018
English Version
Swimming pool equipment - Part 10: Additional specific
safety requirements and test methods for diving platforms,
diving springboards and associated equipment
Équipement de piscine - Partie 10 : Exigences de Schwimmbadgeräte - Teil 10: Zusätzliche besondere
sécurité et méthodes d'essai complémentaires propres sicherheitstechnische Anforderungen und
aux plates-formes de plongeon, aux plongeoirs et à Prüfverfahren für Sprungplattformen, Sprungbretter
l'équipement associé und zugehörige Geräte
This European Standard was approved by CEN on 6 May 2018 and includes Amendment 1 approved by CEN on 8 July 2026.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13451-10:2018+A1:2026 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Safety requirements . 7
4.1 Tolerances . 7
4.2 Diving platforms . 7
4.3 Diving springboards . 13
4.4 Means of access . 18
4.5 Safety barriers . 19
4.6 Slip resistance . 20
4.7 Water diving zones . 21
4.8 Agitation of water surface . 21
4.9 Air cushion equipment . 21
5 Test methods . 22
5.1 General . 22
5.2 Structural integrity of diving springboards . 22
5.3 Structural integrity of stepladders . 23
5.4 Structural integrity of safety barriers . 24
Bibliography . 26

European foreword
This document (EN 13451-10:2018+A1:2026) has been prepared by Technical Committee CEN/TC 136
“Sports, playground and other recreational facilities and equipment”, the secretariat of which is held by
DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2027, and conflicting national standards shall be
withdrawn at the latest by April 2027.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document includes Amendment 1 approved by CEN on 8 July 2026.
This document supersedes !EN 13451-10:2018".
The start and finish of text introduced or altered by amendment is indicated in the text by tags !".
In relation to EN 13451-10 the following main amendments have been made:
a) the values in Tables 2 and 4 have been compared with and where required revised according to the
values of the current FINA Table;
b) clause on stepladders for diving facilities revised (4.4.2);
c) clause on safety barriers revised (4.5);
d) clause on slip resistance revised (4.6).
!deleted text"
The EN 13451 series, Swimming pool equipment consists of the following parts:
— Part 1: General safety requirements and test methods
— Part 2: Additional specific safety requirements and test methods for ladders, stepladders and handle
bends
— Part 3: Additional specific safety requirements and test methods for inlets and outlets and water/air
based water leisure features
— Part 4: Additional specific safety requirements and test methods for starting platforms
— Part 5: Additional specific safety requirements and test methods for lane lines and dividing line
— Part 6: Additional specific safety requirements and test methods for turning boards
— Part 7: Additional specific safety requirements and test methods for water polo goals
— Part 10: Additional specific safety requirements and test methods for diving platforms, diving
springboards and associated equipment
— Part 11: Additional specific safety requirements and test methods for moveable pool floors and
moveable bulkheads
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Introduction
Diving is a voluntary movement into water with arms and head entering the water first or a voluntary
movement into water with feet entering the water first while performing acrobatics.
There can be additional requirements for purposes such as competition swimming, and advice should
be sought from the governing body of the sport in question (see [1] and [2]).
1 Scope
This part of the EN 13451 series specifies safety requirements for diving platforms, diving springboards
and associated equipment in addition to the general safety requirements of EN 13451-1 and is meant to
be read in conjunction with it.
The requirements of this part of the EN 13451 series take priority over those in EN 13451-1.
This part of the EN 13451 series is applicable to platforms and springboards, and associated equipment
for use in classified swimming pools as specified in EN 15288-1 and EN 15288-2.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 13451-1:2011+A1:2016, Swimming pool equipment — Part 1: General safety requirements and test
methods
EN 13451-3, Swimming pool equipment — Part 3: Additional specific safety requirements and test
methods for inlets and outlets and water/air based water leisure features
EN 22768-1, General tolerances — Part 1: Tolerances for linear and angular dimensions without
individual tolerance indications (ISO 2768-1)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 13451-1:2011+A1:2016 and
the following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at http://www.iso.org/obp
3.1
diving facility
installation designed to provide the opportunity of diving
3.2
diving platform
raised rigid horizontal platform, protruding over the water, intended for diving
3.3
diving springboard type 1
raised flexible board, installed at a height 1,0 m ≤ h ≤ 3,05 m above water level and protruding over the
water, intended for diving
3.4
diving springboard type 2
raised flexible board, which can be permanently installed or portable, with a height < 1,0 m from water
level and protruding over the water, intended for recreational diving
3.5
plummet line
vertical line extending through the centre of the front edge of a platform or springboard
3.6
water agitation device
equipment designed to improve visibility of the water surface by disturbance
3.7
air cushion equipment
training device, designed for introducing air from the bottom of a diving pool, in front of a diving
platform and/or springboard, to reduce the effects of the impact of the diver with the pool water and
make training safer
4 Safety requirements
4.1 Tolerances
+0,05
Tolerances of height of the diving platform and diving springboards are m .
For all other tolerances, if not indicated, EN 22768-1 applies.
4.2 Diving platforms
4.2.1 General
Particular attention shall be paid to avoid glare and reflecting surfaces, which can disturb the vision of
the diver.
In Europe, outdoor diving facilities should face north.
4.2.2 Dimensions
The dimensions indicated in Figures 1 to 4 and Tables 1 to 2 shall be complied with. The design of the
equipment does not need to comply with the examples given.
Platforms shall be horizontal.
The minimum dimensions of the platforms shall comply with Table 1.
Table 1 — Areas of use
Dimensions in metres
Height of platforms from water
a
Minimum usable width
Length reserved for the diver
level
1 0,60 0,75
3 0,60 1,25
5 1,50 1,25
7,5 1,50 1,50
10 3,00 1,50
a
Minimum distance back from plummet.
NOTE 1 In addition to the length reserved for the diver (minimum distance back from plummet), additional
space can be necessary for other purposes, as wider range of dives (e.g. dives with preliminary run), space for
waiting for the dive, space for divers passing to the next platform.
If synchronized diving (more than one diver starting at a same time from the platform) is foreseen, the
width of the platforms should be suitably increased. As an alternative, during synchronized diving
activities only there should be the possibility to increase temporarily the distance of the safety barriers
for arm movement (see [1]).
The minimum dimensions of the platform facilities shall comply with Table 2 and with Figure 1.
Table 2 — Minimum dimensions of diving platform facilities
Dimensions in metres
1 m 3 m 5 m 7,5 m 10 m
Minimum height of platform
from water level
horizontal vertical horizontal vertical horizontal vertical horizontal vertical horizontal vertical
From plummet back
A 0,75 — 1,25 — 1,25 — 1,25 — 1,50 —
to pool wall
From plummet back
a
A/A to platform plummet — — — — 0,75 — 0,75 — 0,75 —
vertically below
From plummet to pool
b
B 2,30 — 2,80 — 3,25 — 4,25 — 5,25 —
wall at side
From plummet to
b c
C , 1,65 — 2,00 — 2,25 — 2,50 — 2,75 —
adjacent plummet
From plummet to pool
D 8,00 — 9,50 — 10,25 — 11,00 — 13,50 —
wall ahead
On plummet, from
E — 3,25 — 3,25 — 3,25 — 3,25 — 4,00
board to ceiling
Distance behind and
d
F each side of plummet 2,30 — 2,75 — 2,75 — 2,75 — 2,75 —
with height E
Distance ahead of
G plummet with height 5,00 — 5,00 — 5,00 — 5,00 — 6,00 —
E
Depth of water at
H — 3,20 — 3,50 — 3,70 — 4,10 — 4,50
plummet
Distance ahead of
J plummet with a water 4,50 — 5,50 — 6,00 — 8,00 — 11,00 —
depth K
minimum water depth
K between plummet and — 3,10 — 3,40 — 3,60 — 4,00 — 4,25
distance J
Distance on each side
L of plummet with a 1,40 — 1,80 — 3,00 — 3,75 — 4,50 —
water depth M
minimum water depth
M between plummet and — 3,10 — 3,40 — 3,60 — 4,00 — 4,25
distance L
a
On plummet, also from platform to the bottom side of a platform, if vertically above.
b
Dimensions B and C apply to platforms with widths as in Table 1; if platform widths are increased then B, C, F and L shall be
increased by half of the additional width(s).
c
The dimension C applies also to combinations of platform and spring board (e.g. 5 m platform combined with a 3 m spring board).
d
F is also valid for arm moves backwards, so for the 1 m platform F = 2,75 (backwards) applies.
The maximum slope of surfaces to reduce dimensions beyond full requirements shall be ≤ 30° for
ceilings and pool bottoms.
Dimensions in metres
a) Longitudinal section b) Cross section
Key
1 platform
2 platform underneath other platform
Figure 1 — Diagrammatic side and front view of diving platform facilities
Intermediate heights from water level are allowed, provided the user is made aware of the actual height
and the safety requirements of the next higher facility are fulfilled.
The front edge of each platform shall be vertical, or inclined up to an angle ≤ 10° to the vertical inside
the plummet line. The thickness of the front edge shall be between 200 mm and 300 mm.
Dimensions in millimetres
Key
1 water level
Figure 2 — Diving platform (1 m high)
Dimensions in millimetres
Key
1 water level
Figure 3 — Diving platform (3 m high)
Dimensions in millimetres
Key
1 water level
See also 4.2.2, paragraph after NOTE 1
NOTE The shown constellation of the diving platforms is only an example.
Figure 4 — Diving platforms
...