ASTM C1190-18(2022)

ASTM C1190-18(2022) is a standard published by ASTM International. Its full title is "Standard Practice for Location of Test Specimens from Magnesia-Carbon and Impregnated Burned Basic Brick". This standard covers: SIGNIFICANCE AND USE 4.1 This practice defines a procedure that ensures reasonably consistent preparation of specimens for product testing and evaluation. 4.2 This practice can be used in the laboratories of producers, users, and general interest parties for research and development or quality control work. It is particularly useful for interlaboratory comparisons on products, for repetitive evaluations or comparisons of products or product quality, and in specifying a uniform preparation practice for specimens for acceptance testing. 4.3 If pitch-impregnated samples are prepared by wet cutting or drilling, care should be taken in drying them. If the samples are heated to facilitate drying, the temperature to which they are heated should not be so high that it causes drainage of pitch from the samples. 4.4 Porosities of metal-containing brick must be measured using kerosene or mineral spirits, because using water will result in an artificially low result. SCOPE 1.1 This practice covers a procedure for preparing test specimens from magnesia-carbon and impregnated burned basic brick. This practice generally concerns preparation of test specimens from brick greater than 13 in. (33 cm) in length. These brick are mainly manufactured for use in electric arc furnaces and basic oxygen furnaces. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE 4.1 This practice defines a procedure that ensures reasonably consistent preparation of specimens for product testing and evaluation. 4.2 This practice can be used in the laboratories of producers, users, and general interest parties for research and development or quality control work. It is particularly useful for interlaboratory comparisons on products, for repetitive evaluations or comparisons of products or product quality, and in specifying a uniform preparation practice for specimens for acceptance testing. 4.3 If pitch-impregnated samples are prepared by wet cutting or drilling, care should be taken in drying them. If the samples are heated to facilitate drying, the temperature to which they are heated should not be so high that it causes drainage of pitch from the samples. 4.4 Porosities of metal-containing brick must be measured using kerosene or mineral spirits, because using water will result in an artificially low result. SCOPE 1.1 This practice covers a procedure for preparing test specimens from magnesia-carbon and impregnated burned basic brick. This practice generally concerns preparation of test specimens from brick greater than 13 in. (33 cm) in length. These brick are mainly manufactured for use in electric arc furnaces and basic oxygen furnaces. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM C1190-18(2022) is classified under the following ICS (International Classification for Standards) categories: 91.100.25 - Terracotta building products. The ICS classification helps identify the subject area and facilitates finding related standards.

ASTM C1190-18(2022) has the following relationships with other standards: It is inter standard links to ASTM C133-24, ASTM C831-18(2023), ASTM C1099-07(2019), ASTM C831-18, ASTM C831-98(2017)e1, ASTM C831-98(2017), ASTM C607-88(2016), ASTM C831-98(2013), ASTM C1099-07(2012), ASTM C830-00(2011), ASTM C607-88(2010)e1, ASTM C133-97(2008), ASTM C133-97(2008)e1, ASTM C831-98(2008), ASTM C1099-07. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

ASTM C1190-18(2022) is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.