iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E2030-07

(Guide)

Standard Guide for Recommended Uses of Photoluminescent (Phosphorescent) Safety Markings

Standard Guide for Recommended Uses of Photoluminescent (Phosphorescent) Safety Markings

SIGNIFICANCE AND USE
Photoluminescent safety markings may be used to indicate the direction of the means of egress (escape route).  
Note 1—Specification E 2072 covers photometric requirements for photoluminescent (phosphorescent) safety materials.
Photoluminescent safety markings can be divided into the following categories:
4.2.1 Floor Mounted Markings—These markings include floor tiles, stair treads, stair nosings, floor inserts, tactile warning strips, coatings, epoxy casting resins, and other markings attached to the floor.
4.2.2 Wall Mounted Markings—These markings include coatings, wall bases, tapes, corner guards, signage, exit maps, guidance strips, and other markings attached to walls, doors, handrails, columns, and other obstructions.
SCOPE
1.1 This guide describes recommended uses and information on installation of photoluminescent safety markings. This guide does not establish a standard practice to follow. Required markings shall be installed in accordance with applicable building codes.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Dec-2006
ICS
13.100 - Occupational safety. Industrial hygiene
Technical Committee
E12 - Color and Appearance
Drafting Committee
E12.13 - Photoluminescent Safety Markings
Current Stage
Ref Project

Relations

Replaces
ASTM E2030-06a - Standard Guide for Recommended Uses of Photoluminescent (Phosphorescent) Safety Markings
Effective Date
01-Jan-2007
Replaced By
ASTM E2030-08 - Standard Guide for Recommended Uses of Photoluminescent (Phosphorescent) Safety Markings
Effective Date
01-Jun-2008

Buy Standard

ASTM E2030-07 - Standard Guide for Recommended Uses of Photoluminescent (Phosphorescent) Safety MarkingsASTM E2030-07 - Standard Guide for Recommended Uses of Photoluminescent (Phosphorescent) Safety Markings
PreviousNext
Guide
ASTM E2030-07 - Standard Guide for Recommended Uses of Photoluminescent (Phosphorescent) Safety Markings
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: E 2030 – 07
Standard Guide for
Recommended Uses of Photoluminescent (Phosphorescent)
1
Safety Markings
This standard is issued under the fixed designation E 2030; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope 4.2 Photoluminescent safety markings can be divided into
the following categories:
1.1 This guide describes recommended uses and informa-
4.2.1 Floor Mounted Markings—These markings include
tion on installation of photoluminescent safety markings. This
floor tiles, stair treads, stair nosings, floor inserts, tactile
guidedoesnotestablishastandardpracticetofollow.Required
warning strips, coatings, epoxy casting resins, and other
markings shall be installed in accordance with applicable
markings attached to the floor.
building codes.
4.2.2 Wall Mounted Markings—These markings include
1.2 The values stated in SI units are to be regarded as the
coatings, wall bases, tapes, corner guards, signage, exit maps,
standard. The values given in parentheses are for information
guidance strips, and other markings attached to walls, doors,
only.
handrails, columns, and other obstructions.
1.3 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
5. Recommended Applications
responsibility of the user of this standard to establish appro-
5.1 Floor Proximity Exit Path Marking—This provides a
priate safety and health practices and determine the applica-
continuous delineation of the means of egress (escape route)
bility of regulatory limitations prior to use.
from the occupied area to any exit doors that lead directly to
2. Referenced Documents the public way, except as interrupted by intersecting corridors.
2
Floor proximity exit path markings should be at least 100-mm
2.1 ASTM Standards:
(4-in.) wide in all locations. If narrower widths are used, the
E 284 Terminology of Appearance
luminance shall increase, as indicated in Specification E 2072,
E 2072 Specification for Photoluminescent (Phosphores-
section on Installation Site, On-Site Luminance. Floor prox-
cent) Safety Markings
imity exit path markings should be applied to the floor surface
3. Terminology or installed on the wall, close to the floor (see Figs. 1-3).
5.2 Continuous Wall and Floor Markings in Corridors
3.1 Definitions of terms in Terminology E 284 are appli-
5.2.1 Corridors 2-m (2.2-yd) or wider should be marked on
cable to this guide.
both sides.
4. Significance and Use
5.2.2 In dead end corridors only, the direction of travel
should be indicated by directional indicators pointing in the
4.1 Photoluminescent safety markings may be used to
direction of the means of egress (escape route). The maximum
indicate the direction of the means of egress (escape route).
spacing between the individual directional indicators should be
NOTE 1—Specification E 2072 covers photometric requirements for
1-m (1.1-yd).
photoluminescent (phosphorescent) safety materials.
5.3 Marking of Exit Doors and Emergency Exits—Exit
doors and emergency exits in the course of the egress path
should be marked with high and floor proximity exit signs.
1
This guide is under the jurisdiction of ASTM Committee E12 on Color and
Such doors should also either be marked all around by
Appearance and is the direct responsibility of Subcommittee E12.13 on Photolu-
highlighting their entire frames or by leading the pathway
minescent Safety Markings.
marking up to the level of the door handle on the side of the
Current edition approved Jan. 1, 2007. Published February 2007. Originally
approved in 1999. Last previous edition approved in 2006 as E 2030 - 06a.
door where the handle is located (see Figs. 1-3). To aid in
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
locating the door release, its knob/latch/bar should be marked
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
by placing photoluminescent material behind it or on it. (see
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. Figs. 2 and 3).
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
E2030–07
FIG. 1 Wall and Floor Markings in a Corridor
5.3.1 Doors inside an enclosed exit stairway that do not 5.8 Exit Maps should be provided on each floor, located
allow re-entry into the building should be marked by photolu- next to the eleva
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E1499-16(2023)(Guide)
Standard Guide for Selection, Evaluation, and Training of Observers

SIGNIFICANCE AND USE
5.1 The term appearance (see 3.2.1) implies the essential presence of human visual observations. The results of visual observation involve not only the step of observing, accomplished by the eye, but also the inseparable step of interpretation in the brain. Instrumental test methods currently cannot duplicate this second step, and therefore can now only approximate, but not fully measure, appearance. Such instrumental measures of appearance properties are useful only to the extent that they can be correlated to the results of visual observations by observers of the appearance phenomena being evaluated.  
5.2 Almost invariably, too little attention has been paid to ensuring that the essential visual observations have been properly obtained to provide the basis for correlating visual and instrumental test results.  
5.3 This guide provides the means for assessing observers, by outlining the requirements and tests for their selection, evaluation, and training. This guide should be useful to all experimenters designing or using visual test methods to provide either direct results in terms of the observation of appearance properties, or the experiments correlating such results with instrumental measures approximating the same appearance properties. The user is cautioned to avoid the substitution of validated vision tests with replicas of any kind, either printed, photographed or digitally displayed.
SCOPE
1.1 This guide describes criteria and tests for selecting, evaluating, and training human visual-sensory observers for tasks involving the perception and scaling of properties and phenomena relating to appearance.  
1.2 Examples of tests requiring the use of trained observers include but are not limited to those described in the following ASTM standards: on color, Practice D1535 and Practice E1360; on color difference, Practice D1729 and Test Method D2616; on gloss, Test Method D4449; on metamerism, Practice D4086; and on setting tolerances, Practice D3134.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM E2073-19a(Test Method)
Standard Test Method for Photopic Luminance of Photoluminescent (Phosphorescent) Markings

SIGNIFICANCE AND USE
4.1 To assess how photoluminescent markings perform under identical test conditions, the luminance shall be measured in accordance with this test method (see Specification E2072).
SCOPE
1.1 This test method covers a procedure for determining the photopic luminance of photoluminescent (phosphorescent) markings. It does not cover scotopic or mesopic measurements.  
1.2 When reference is made regarding photoluminescence in the text of this test method, it implies phosphorescence.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D5745-23(Guide)
Standard Guide for Developing and Implementing Interim and Early Actions for Waste Contamination Site Remediation

SIGNIFICANCE AND USE
5.1 This guide is intended to provide a systematic approach for the application and execution of early actions for purposes of remediating both hazardous and non-hazardous contamination. Iterative development of a CSM is fundamental to the use of this guide.  
5.2 Anticipated users of this guide are owners or operators at sites of environmental contamination; technical professionals involved in the field of environmental site characterization and remediation; environmental regulators, property owners, employees, and residents adjacent to sites of environmental contamination; and lenders, sureties, and persons of general interest within an affected community.  
5.3 This guide is not intended to replace legal requirements for remediating sites of environmental contamination. This guide should be used to supplement existing regulatory guidance and to focus remedial efforts toward final remedy solutions.
Note 2: The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors.
SCOPE
1.1 The purpose of this guide is to assist practitioners in the development, selection, design, and implementation of interim, short-term, or early action remedies undertaken at sites of waste contamination for the purpose of managing, controlling, or reducing risk posed by environmental site contamination. Early action remedies and strategies are applicable to the management of other regulatory processes (for example, state underground storage tank (UST) programs are equally applicable) in addition to the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA)/National Oil and Hazardous Substances Pollution Contigency Plan (NCP) process. This guide identifies and describes a standard process, technical requirements, information needs, benefits, and strategy for early actions.  
1.2 This guide is applicable to both nonhazardous and hazardous sites of contamination as defined by CERCLA as amended by the Superfund Amendments and Reauthorization Act of 1986 (SARA) and the Resource Conservation and Recovery Act (RCRA) as amended by the Hazardous and Solid Waste Amendments (HSWA) of 1986.  
1.3 To the extent that this guide may be used for hazardous materials operations, it does not address the applicability of regulatory limitations and local requirements.  
1.4 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development...

  • Guide
    6 pages
    English language
    sale 15% off
  • Guide
    6 pages
    English language
    sale 15% off
ASTM
ASTM E1499-16(2023)(Guide)
Standard Guide for Selection, Evaluation, and Training of Observers

SIGNIFICANCE AND USE
5.1 The term appearance (see 3.2.1) implies the essential presence of human visual observations. The results of visual observation involve not only the step of observing, accomplished by the eye, but also the inseparable step of interpretation in the brain. Instrumental test methods currently cannot duplicate this second step, and therefore can now only approximate, but not fully measure, appearance. Such instrumental measures of appearance properties are useful only to the extent that they can be correlated to the results of visual observations by observers of the appearance phenomena being evaluated.  
5.2 Almost invariably, too little attention has been paid to ensuring that the essential visual observations have been properly obtained to provide the basis for correlating visual and instrumental test results.  
5.3 This guide provides the means for assessing observers, by outlining the requirements and tests for their selection, evaluation, and training. This guide should be useful to all experimenters designing or using visual test methods to provide either direct results in terms of the observation of appearance properties, or the experiments correlating such results with instrumental measures approximating the same appearance properties. The user is cautioned to avoid the substitution of validated vision tests with replicas of any kind, either printed, photographed or digitally displayed.
SCOPE
1.1 This guide describes criteria and tests for selecting, evaluating, and training human visual-sensory observers for tasks involving the perception and scaling of properties and phenomena relating to appearance.  
1.2 Examples of tests requiring the use of trained observers include but are not limited to those described in the following ASTM standards: on color, Practice D1535 and Practice E1360; on color difference, Practice D1729 and Test Method D2616; on gloss, Test Method D4449; on metamerism, Practice D4086; and on setting tolerances, Practice D3134.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM E848-94(2022)(Guide)
Standard Guide for Safety and Health Requirements Relating to Occupational Exposure to Water-Insoluble Chromates

SIGNIFICANCE AND USE
4.1 This guide includes chromates that are not readily soluble in water and that have water solubilities (Chromate ION) within the range of the more soluble calcium chromate and the much less soluble lead chromate. The major occupations involving potential exposure to insoluble chromates are in roasting of chromite ore, the manufacture of chromate pigments, the manufacture of coatings containing chromate pigments, and spray painting with these coatings. There is insufficient evidence to conclude that trivalent chromium compounds are carcinogenic.
SCOPE
1.1 This guide covers control procedures for the safe production, storage, transportation, and handling of only the hexavalent chromium compounds found in Table 1 and their various hydrates, and mixtures of coprecipitates of the same regardless of crystalline form.  
1.2 This guide is not intended to cover (a) such “soluble” chromates as chromates of sodium, potassium, magnesium, or ammonium; (b) soluble bichromates; (c) chromic acid; (d) volatile chromyl compounds; (e) any trivalent chromium compound; or (f) elemental chromium. Omission of said compounds or classes of compounds should not be construed to mean that they may be handled without due regard to their particular physical, chemical, and toxicological hazards (9, 10, 11).  
1.3 The chromate ion, CrO4−2, depending upon the acidity, complexes to form di-, tri-, and higher polychromates; hence, the chromates listed in Table 1 may contain mixtures of polychromates, depending on the method of isolation and end use.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (For more specific precautionary information see Section 5.)  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    12 pages
    English language
    sale 15% off
ASTM
ASTM D3670-91(2022)(Guide)
Standard Guide for Determination of Precision and Bias of Methods of Committee D22

SIGNIFICANCE AND USE
5.1 The objective of this standard is to provide guidelines to Committee D22 for the evaluation of the precision and bias, or both, of ASTM standard methods and practices at the time of their development. Such an evaluation is necessary to assure that a cross section of interested laboratories could perform the test and achieve satisfactory results, using the method as written. It also provides guidance to the user as to what levels of precision and accuracy may be expected in such usage.  
5.2 The write-up of the method describes the media for which the test method is believed to be appropriate. The collaborative test corroborates the write-up within the limitations of the test design. A collaborative test can only use representative media so that universal applicability cannot be implied from the results.  
5.3 The fundamental assumption of the collaborative test is that the media tested, the concentrations used, and the participating laboratories are representative and provide a fair evaluation of the scope and applicability of the test method as written.
SCOPE
1.1 This standard provides guidance to task groups of Committee D22 on Sampling and Analysis of Atmospheres in planning and conducting collaborative testing of candidate methods.  
1.2 It is intended for use with other ASTM practices for the determination of precision and bias.  
1.3 It is applicable to most manual and automated methods and to most components of monitoring systems. It is recognized that the evaluation of monitoring systems may provide special problems. Practice D3249 should be considered for general guidance in this respect.  
1.4 It is directly applicable to chemical methods and in principle to most physical methods, sampling methods, and calibration procedures.  
1.5 The processes described are for the general validation of methods of test. A user has the obligation and responsibility to validate any method it uses for a specific application and to demonstrate its own competence in the use of validated methods.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    5 pages
    English language
    sale 15% off
ASTM
ASTM D8143-17(2022)(Test Method)
Standard Test Method for Determination of the EU-8 List of PAH Compounds in Carbon Black

SIGNIFICANCE AND USE
5.1 This test procedure is used to determine the individual concentrations of the PAH compounds in the EU-8 list extracted from carbon black by the means of a Soxhlet extraction apparatus with toluene.
SCOPE
1.1 This test method covers the qualitative and quantitative determination of the EU-8 list of polycyclic aromatic hydrocarbons (PAH) on carbon black. The EU-8 list of PAH compounds is given in Table 1. The procedure involves Soxhlet extraction with toluene followed by extract analysis using gas chromatography with mass spectrometry (GC/MS). This method is not intended to test for U.S. Food and Drug Administration (FDA 21 CFR 178.3297) compliance of carbon blacks used for indirect food contact applications.  
1.2 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM C1057-22(Practice)
Standard Practice for Determination of Skin Contact Temperature from Heated Surfaces Using a Mathematical Model and Thermesthesiometer

SIGNIFICANCE AND USE
5.1 The procedures in this practice support the determination of the burn hazard potential for a heated surface. These procedures provide an estimate of the maximum skin contact temperature and must be used in conjunction with Guide C1055 to evaluate the surface hazard potential.  
5.2 The two procedures outlined herein are both based upon the same heat transfer principles. Method A uses a mathematical model to predict the contact temperature, while Method B uses a plastic rubber probe having similar heat transfer characteristics to the human finger to “measure” the contact temperature on real systems.  
5.3 These procedures serve as an estimate for the skin contact temperatures which might occur for the “average” individual. Unusual conditions of exposure, incorrect design assumptions, subject health conditions, or unforeseen operating conditions will potentially negate the validity of the estimations.  
5.4 These procedures are limited to direct contact exposure only. Conditions of personal exposure to periods of high ambient temperatures, direct flame exposure, or high radiant fluxes will potentially cause human injury in periods other than determined herein. Evaluation of exposures other than direct contact are beyond the scope of this practice.  
5.5 Cold Surface Exposure—No consensus criteria exists for the destruction of skin cells by freezing. If, at some future time, such criteria are developed, extrapolation of the techniques presented here will serve as a basis for cold surface exposure evaluation.
SCOPE
1.1 This practice covers a procedure for evaluating the skin contact temperature for heated surfaces. Two complimentary procedures are presented. The first is a purely mathematical approximation that is used during design or for worst case evaluation. The second method describes the thermesthesiometer, an instrument that analogues the human sensory mechanism and is only used on operating systems.  
Note 1: Both procedures listed herein are intended for use with Guide C1055. When used in conjunction with that guide, these procedures can determine the burn hazard potential for a heated surface.  
1.2 A bibliography of human burn evaluation studies and surface hazard measurement is provided in the References at the end of Guide C1055. Thermesthesiometer and mathematical modeling references are provided in the References at the end of this practice (1-5).2  
1.3 This practice addresses the skin contact temperature determination for passive heated surfaces only. The analysis procedures contained herein are not applicable to chemical, electrical, or other similar hazards that provide a heat generation source at the location of contact.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM E2148-21(Guide)
Standard Guide for Using Documents Related to Metalworking or Metal Removal Fluid Health and Safety

SIGNIFICANCE AND USE
4.1 Application of this guide will provide users with information on how to use the various documents listed in Section 2 related to health and safety of metalworking and metal removal fluids.  
4.2 Users of the documents listed in Section 2 may fall into several categories, such as producers of metalworking or metal removal fluids, suppliers of raw materials to those producers, users of metalworking or metal removal fluids, and other interested parties such as non-governmental organizations.  
4.3 While all parties may wish to be generally familiar with all the documents listed in Section 2, producers and users may each want to focus on certain documents which are directly applicable to them:  
4.4 Documents Applicable to Producers:  
4.4.1 E1687 Test Method for Determining Carcinogenic Potential of Virgin Base Oils in Metalworking Fluids:  
4.4.1.1 Test Method E1687 covers a microbiological test procedure based upon the Salmonella  mutagenesis assay of Ames et al.7 (see also Maron et al.).8 It can be used as a screening technique to detect the presence of potential dermal carcinogens in virgin base oils used in the formulation of metalworking oils. Persons who use this test should be well versed in the conduct of the Ames test and conversant with the physical and chemical properties of petroleum products.
4.4.1.2 Producers of metalworking fluids and metal removal fluids should assure themselves that virgin base oils used in the formulation of neat metalworking and metal removal oils and soluble and semi-synthetic metal removal fluids have an acceptable mutagenicity index or mutagenic potency index.  
4.4.2 E1302 Guide for Acute Animal Toxicity Testing of Water-Miscible Metal Removal Fluids:  
4.4.2.1 Guide E1302 defines acute animal toxicity tests and sets forth references for procedures to assess the acute toxicity of water-miscible metal removal fluids as manufactured.
4.4.2.2 Application of Guide E1302 will provide information on the acute toxicity ...
SCOPE
1.1 This guide covers information on how to use documents related to health and safety of metalworking and metal removal fluids. As such, this guide will provide the user with sufficient background information to effectively use the documents listed in Section 2. Documents referenced in this guide are grouped as applicable to producers, to users or to all.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    5 pages
    English language
    sale 15% off
  • Guide
    5 pages
    English language
    sale 15% off
ASTM
ASTM E2565-21(Guide)
Standard Guide for Consensus-Based Process for an Occupational Safety and Health Standard That Includes an Occupational Exposure Guideline

SIGNIFICANCE AND USE
5.1 This guide is designed to help identify and integrate affected stakeholder interests and to include relevant scientific and technical information when developing occupational safety and health standards that include or are proposed to include an OEG.  
5.2 This guide shall be used when updating an occupational safety and health standard containing an OEG.  
5.3 While use of the CBSD process is required for occupational safety and health standards that include an OEG, it may also be used to improve stakeholder involvement and technical input for other occupational safety and health standards.  
5.4 The CBSD process is intended:
(1) To obtain representation on the committee or subcommittee from sectors that are substantially impacted by a specific standard project; and
(2) To obtain adequate input when the project requires review and analysis of information that is highly technical, very specialized, or not widely available.
SCOPE
1.1 This guide presents a framework for a stakeholder-focused, consensus-based decision-making process for occupational safety and health standard development activities that include adoption or development of occupational exposure guidelines (OEGs) as a part of occupational health and safety standards.  
1.2 This guide applies to safety and health standard development activities in which an occupational exposure guideline will be included as one element of a comprehensive standard that addresses safety and health management strategies such as communication, monitoring, and controls. It is not meant to be used to develop an OEG apart from the context of such management strategies. In cases where other occupational exposure limit (OEL) establishing bodies have developed OELs, those may be reviewed, assimilated, or adapted rather than recreated ab initio.  
1.3 This guide does not replace existing consensus-based decision-making or committee participation processes that are used to develop safety and health standards. It is intended to be used in conjunction with such processes to improve scientific and technical input and stakeholder involvement in occupational safety and health decision-making for such standards.  
1.4 Limitations—This guide does not prescribe specific methods for generating or evaluating scientific and technical data related to assessing a particular occupational safety and health issue. Occupational safety and health standards apply to a wide variety of substances and occupational exposure circumstances. It is not possible to anticipate all situations where an OEG may be useful for a standard. This guide will be helpful in promoting appropriate balance and input, but the consensus process must deal with real-world complexities that individual standards may involve.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off