2022-01-1367 - Pravilnik o uveljavljanju davčnih olajšav za vlaganja v digitalni in zeleni prehod

This document specifies principles and requirements and provides guidance at the project level for the quantification, monitoring and reporting of activities intended to cause greenhouse gas (GHG) emission reductions or removal enhancements. It includes requirements for planning a GHG project, identifying and selecting GHG sources, sinks and reservoirs (SSRs) relevant to the project and baseline scenario, monitoring, quantifying, documenting and reporting GHG project performance and managing data quality.
The ISO 14060 family of standards is GHG programme neutral. If a GHG programme is applicable, the requirements of that GHG programme are additional to the requirements of the ISO 14060 family of standards.

This document specifies principles and requirements at the organization level for the quantification and reporting of greenhouse gas (GHG) emissions and removals. It includes requirements for the design, development, management, reporting and verification of an organization's GHG inventory.
The ISO 14064 series is GHG programme neutral. If a GHG programme is applicable, requirements of that GHG programme are additional to the requirements of the ISO 14064 series.

This document specifies principles, requirements and guidelines for the quantification and reporting of the carbon footprint of a product (CFP), in a manner consistent with International Standards on life cycle assessment (LCA) (ISO 14040 and ISO 14044).
Requirements and guidelines for the quantification of a partial CFP are also specified.
This document is applicable to CFP studies, the results of which provide the basis for different applications (see Clause 4).
This document addresses only a single impact category: climate change. Carbon offsetting and communication of CFP or partial CFP information are outside the scope of this document.
This document does not assess any social or economic aspects or impacts, or any other environmental aspects and related impacts potentially arising from the life cycle of a product.

ISO 10077-1:2017 specifies methods for the calculation of the thermal transmittance of windows and pedestrian doors consisting of glazed and/or opaque panels fitted in a frame, with and without shutters.

ISO 6946:2017 provides the method of calculation of the thermal resistance and thermal transmittance of building components and building elements, excluding doors, windows and other glazed units, curtain walling, components which involve heat transfer to the ground, and components through which air is designed to permeate.
The calculation method is based on the appropriate design thermal conductivities or design thermal resistances of the materials and products for the application concerned.
The method applies to components and elements consisting of thermally homogeneous layers (which can include air layers).
ISO 6946:2017 also provides an approximate method that can be used for elements containing inhomogeneous layers, including the effect of metal fasteners, by means of a correction term given in Annex F. Other cases where insulation is bridged by metal are outside the scope of ISO 6946:2017.
NOTE   Table 1 in the Introduction shows the relative position of ISO 6946:2017 within the set of EPB standards in the context of the modular structure as set out in ISO 52000‑1.

ISO 12631:2017 specifies a method for calculating the thermal transmittance of curtain walls consisting of glazed and/or opaque panels fitted in, or connected to, frames.
The calculation includes:
-      different types of glazing, e.g. glass or plastic; single or multiple glazing; with or without low emissivity coating; with cavities filled with air or other gases;
-      frames (of any material) with or without thermal breaks;
-      different types of opaque panels clad with metal, glass, ceramics or any other material.
Thermal bridge effects at the rebate or connection between the glazed area, the frame area and the panel area are included in the calculation.
The calculation does not include:
-      effects of solar radiation;
-      heat transfer caused by air leakage;
-      calculation of condensation;
-      effect of shutters;
-      additional heat transfer at the corners and edges of the curtain walling;
-      connections to the main building structure nor through fixing lugs;
-      curtain wall systems with integrated heating.
NOTE       Table 1 in the Introduction shows the relative position of ISO 12631:2017 within the set of EPB standards in the context of the modular structure as set out in ISO 52000-1.