F17.68 - Energy Piping Systems

SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, and markings for on-site manufactured multilayer reinforced polyethylene composite pipe. It covers nominal sizes 6 in. through 36 in. (150 mm through 915 mm). These multilayered reinforced polyethylene composite pipe products2 are assembled and installed in various lengths, including long continuous lengths. These products are intended for the transport of crude oil, natural gas and hazardous liquids in the rehabilitation of existing pipelines and for new pipelines.
Note 1: Hazardous liquids are those liquids defined by the U.S. Department of Transportation in 49 CFR 195.2.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers requirements and test methods for polyamide-12 (PA12) materials, pipe and fittings for pressure or non-pressure oil and gas producing applications to convey fluids such as oil, dry or wet gas, multiphase fluids, and non-potable oilfield water. This specification does not cover pipe for gas distribution applications.  
1.1.1 See Specification F2785 for PA12 pipe and fittings intended for use in the distribution of natural gas, or for use with liquefied petroleum gas.  
1.1.2 Pipe and fittings covered by this specification shall not be joined using taper pipe threads. Butt fusion joining shall be done in accordance with Practice F3372. In-plant quality control programs are described in Appendix X1. Design considerations are discussed in Appendix X2.  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers crosslinked polyethylene (PEX) pipe that is outside diameter controlled in metric pipe sizes (DN 16 to 1000) and inch pipe sizes (NPS 3 to 54), and pressure rated (see Appendix X1) using the ISO MRS rating system. This specification is intended for PEX pipe made by various processes, as long as the PEX pipe made by that process meets all the requirements of this specification. Included are requirements and test methods for material, workmanship, UV protection, dimensions, hydrostatic sustained pressure, chemical resistance, minimum operating temperature, degree of crosslinking, squeeze-off, and hydrostatic burst pressure. Requirements for pipe markings are also given. The pipe covered by this specification is intended for pressure or non-pressure oil and gas producing applications such as conveying oil, dry or wet gas, gas gathering, multiphase fluids, and non-potable oilfield water. This specification does not cover gas distribution applications.  
Note 1: Gas gathering applications where the pipe size is greater than NPS 8 may be subject to PHMSA design, material, and installation requirements.  
1.2 This specification also includes requirements for qualifying joints made using polyethylene electrofusion fittings (such as Specification F3373) and PEX pipe. Fittings to be used with PEX pipe manufactured to this specification are in Specification F2829. Installation considerations are in X2.2.
Note 2: NPS fittings should not be used for DN sized pipe, and DN sized fittings should not be used for NPS pipe.  
1.3 The text of this specification references notes, footnotes, and appendixes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) should not be considered as requirements of the specification.  
1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.4.1 For consistency with ISO 9080, MRS values shall only be in SI units for conversion to the pipe material designation (for example PEX material in pipe form with an MRS of 8 MPa is designated a PEX 80.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers outside diameter controlled crosslinkable polyethylene (CX-PE) pipe produced in sizes DN 25 to 630 and NPS 1 to 24 in various dimension ratios. Included in this specification are requirements and test methods for the determination of the long-term hydrostatic strength, hydrostatic burst pressure, hydrostatic sustained pressure, UV weathering resistance, initial and ultimate degree of crosslinking, workmanship, and marking.  
1.2 This specification shall not be applied to crosslinked products, specifically PEX pipe or tubing.
Note 1: CX-PE is a different designation separate from conventional PEX materials, specifically with regard to the crosslinking rate, installation, and commissioning processes.  
1.3 The pipe covered by this specification is intended for pressure and non-pressure applications. Fluids such as non-potable water, multi-phase mixed fluids, crude oils, gases, and chemical solutions containing some water are allowed to be transported in pipe made in accordance with this standard. Permissible operating temperatures for commissioned piping systems constructed from CX-PE pipe manufactured in accordance with this specification are ≤ 200 °F [93 °C].  
1.4 Pipe produced in accordance with this specification is intended to be crosslinked during or after installation. The procedures and practices to be used for the installation and crosslinking of the CX-PE pipe are outside the scope of this specification. Manufacturer’s recommendations for the commissioning of CX-PE pipe are used to ensure that the performance of the completed piping system meets design expectations.
Note 2: The difference between pipes made in accordance with this specification and PEX pipes made in accordance with Specification F2905 is that the final crosslinking process is completed as part of installation and commissioning as opposed to crosslinking taking place in the manufacturing facility.  
1.5 This specification includes requirements to demonstrate a minimum level of performance in service.  
1.6 Joining of CX-PE pipes made in accordance with this specification is outside the scope of this specification. For guidance on the joining of CX-PE pipe consult Practice F3507 and manufacturer’s recommendations.  
1.7 This specification references notes, footnotes, and appendixes, which provide non-mandatory explanatory material. Excluding table footnotes which are mandatory, notes, footnotes and information in parentheses shall not be considered as requirements of this specification.  
1.8 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, markings for factory manufactured multilayer flexible steel pipe with thermoplastic inner and outer layers and end connections (Fig. 1). It covers nominal sizes 2 in. through 8 in. (50 mm through 200 mm). Flexible steel pipes are multilayered pipe products manufactured in long continuous lengths and reeled for storage, transport and installation. The multilayer thermoplastic and flexible steel pipe governed by this standard are intended for use for the transport of crude oil, natural gas, hazardous chemicals, industrial chemicals and water.2
FIG. 1 Cutaway of Flexible Steel Pipe  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the requirements and test methods for outside diameter controlled, pressure rated, black metric-sized and IPS-sized crosslinked polyethylene (PEX) pipe, fittings and joints intended for oil and gas producing applications. It presents the criteria for materials made in pipe dimension ratios ranging from 6 to 17, along with workmanship, burst pressure, hydrostatic sustained pressure, bent-pipe hydrostatic pressure, stabilizer functionality, degree of crosslinking, and chemical resistance. It also includes guidelines for pipe and fittings markings.
SCOPE
1.1 This specification covers outside diameter controlled, pressure rated, metric-sized and inch-sized black or yellow crosslinked polyethylene (PEX) pipe made in pipe dimension ratios ranging from 6 to 17. Included are requirements and test methods for material, workmanship, dimensions, burst pressure, hydrostatic sustained pressure, stabilizer functionality, bent-pipe hydrostatic pressure, degree of crosslinking, chemical resistance, and minimum operating temperature. Requirements for pipe markings are also given. The pipe covered by this specification is intended for pressure or non-pressure oil and gas producing applications, such as conveying oil, dry or wet gas, gas gathering, multiphase fluids, and non-potable oilfield water. This specification does not cover piping for gas distribution applications.  
1.2 This specification also includes requirements for joints made between PEX pipe and polyethylene electrofusion fittings (specified in Specifications F1055 or F3373). Fittings to be used with PEX pipe manufactured to this Specification are in Specification F2829/F2829M. Installation considerations are in Appendix X3.  
1.3 The text of this specification references notes, footnotes, and appendixes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
Note 1: Metric sized (SI units) pipe should only be joined with corresponding metric sized fittings, and inch sized pipe should only be joined with corresponding inch sized fittings. Inch sized fittings should not be used for metric sized pipe, and metric sized fittings should not be used for IPS inch sized pipe.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the requirements and test methods for high-density polyethylene (PE) materials, line pipes, and fittings used in pressure or non-pressure oil and gas producing applications to convey fluids such as oil, dry or wet gas, multiphase fluids, and non-potable oilfield water. This specification does not apply to pipes for gas distribution applications. PE material compounds suitable for use in the manufacture of pipes and fittings under this specification shall adhere to values of the following properties: density (natural base resin), melt index, flexural modulus, tensile strength at yield, SCG resistance, hydrostatic strength, color and UV stabilization, hydrostatic design stress, and hydrostatic design basis. The line pipes shall meet specific requirements as to workmanship, dimensions (outside diameter, toe-in, outside surface irregularity, ovality, wall thickness, and special sizes), inside surface ductility, tensile elongation, bendback resistance, elevated temperature sustained pressure, short-term strength and pressurization, apparent tensile strength at yield, and carbon black content. And conversely, PE fittings shall be manufactured in accordance with their intended use with correspondingly sized PE line pipes, as follows: socket fusion fittings, butt fusion fittings, electrofusion fittings, fabricated fittings, and transition fittings.
SCOPE
1.1 This specification covers requirements and test methods for high-density polyethylene (PE) materials, pipe and fittings for pressure or non-pressure oil and gas producing applications to convey fluids such as oil, dry or wet gas, multiphase fluids, and non-potable oilfield water. This specification does not cover pipe for gas distribution applications.  
1.1.1 For the purposes of this specification, high-density polyethylene material is Specification D3350 density cell classification 3 or higher. This specification does not cover materials having Specification D3350 density cell classification less than 3 such as medium or low density polyethylene materials.  
1.1.2 See Specification D2513 for polyethylene pipe and fittings intended for use in the distribution of natural gas, or for use with liquefied petroleum gas.  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification establishes the requirements and test methods for 1/2 in. through 14 in. multilayer polyethylene-polyamide (PE-PA) pipe, which is a two-layer pipe (PE pipe layer bonded to an inner layer of PA). It covers the multilayer pipe for use in piping applications where the permeation and chemical resistance of PA compounds may be useful to protect the PE pipe layer, such as oil and gas producing applications that convey oil, dry or wet gas, and multiphase fluids. Electrofusion and mechanical joints are typically used for this multilayer pipe.
SCOPE
1.1 This specification covers requirements and test methods for 1/2 in. through 14 in. multilayer polyethylene-polyamide (PE-PA) pipe, which is a two-layer pipe (PE pipe layer bonded to an inner layer of PA). The multilayer pipe covered by this specification is intended for use in piping applications where the permeation and chemical resistance of polyamide (PA) compounds may be useful to protect the PE pipe layer, such as oil and gas producing applications that convey oil, dry or wet gas, and multiphase fluids.
Note 1: Permeability and chemical resistance depends on the type of PA used. The PA layer delays but does not prevent liquid hydrocarbons effects. Therefore, the hydrocarbon chemical design factor for this multilayer pipe should be the same as for PE pipe layer—see X1.2.  
1.2 Electrofusion and mechanical joints are typically used for this multilayer pipe.  
1.3 Unless specified otherwise, all the pipe requirements in this specification are for the multilayer pipe.  
1.4 The PA layer is not taken into consideration for the design pressure of multilayer pipe meeting this specification. Design pressure rating is determined from the PE pipe layer alone—see Appendix X1.  
1.5 Units—The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in figures and tables) shall not be considered as requirements of the standard.  
1.7 The following precautionary caveat pertains only to the test method portion, Section 6, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers requirements and test methods for polyamide-12 (PA12) materials, pipe and fittings for pressure or non-pressure oil and gas producing applications to convey fluids such as oil, dry or wet gas, multiphase fluids, and non-potable oilfield water. This specification does not cover pipe for gas distribution applications.  
1.1.1 See Specification F2785 for PA12 pipe and fittings intended for use in the distribution of natural gas, or for use with liquefied petroleum gas.  
1.1.2 Pipe and fittings covered by this specification shall not be joined using taper pipe threads. Butt fusion joining shall be done in accordance with Practice F3372. In-plant quality control programs are described in Appendix X1. Design considerations are discussed in Appendix X2.  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the requirements and test methods for outside diameter controlled, pressure rated, black metric-sized and IPS-sized crosslinked polyethylene (PEX) pipe, fittings and joints intended for oil and gas producing applications. It presents the criteria for materials made in pipe dimension ratios ranging from 6 to 17, along with workmanship, burst pressure, hydrostatic sustained pressure, bent-pipe hydrostatic pressure, stabilizer functionality, degree of crosslinking, and chemical resistance. It also includes guidelines for pipe and fittings markings.
SCOPE
1.1 This specification covers outside diameter controlled, pressure rated, metric-sized and inch-sized black or yellow crosslinked polyethylene (PEX) pipe made in pipe dimension ratios ranging from 6 to 17. Included are requirements and test methods for material, workmanship, dimensions, burst pressure, hydrostatic sustained pressure, stabilizer functionality, bent-pipe hydrostatic pressure, degree of crosslinking, chemical resistance, and minimum operating temperature. Requirements for pipe markings are also given. The pipe covered by this specification is intended for pressure or non-pressure oil and gas producing applications, such as conveying oil, dry or wet gas, gas gathering, multiphase fluids, and non-potable oilfield water. This specification does not cover piping for gas distribution applications.  
1.2 This specification also includes requirements for joints made between PEX pipe and polyethylene electrofusion fittings (specified in Specifications F1055 or F3373). Fittings to be used with PEX pipe manufactured to this Specification are in Specification F2829/F2829M. Installation considerations are in Appendix X3.  
1.3 The text of this specification references notes, footnotes, and appendixes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
Note 1: Metric sized (SI units) pipe should only be joined with corresponding metric sized fittings, and inch sized pipe should only be joined with corresponding inch sized fittings. Inch sized fittings should not be used for metric sized pipe, and metric sized fittings should not be used for IPS inch sized pipe.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the requirements and test methods for outside diameter controlled, pressure rated, black metric-sized and IPS-sized crosslinked polyethylene (PEX) pipe, fittings and joints intended for oil and gas producing applications. It presents the criteria for materials made in pipe dimension ratios ranging from 6 to 17, along with workmanship, burst pressure, hydrostatic sustained pressure, bent-pipe hydrostatic pressure, stabilizer functionality, degree of crosslinking, and chemical resistance. It also includes guidelines for pipe and fittings markings.
SCOPE
1.1 This specification covers outside diameter controlled, pressure rated, metric-sized and inch-sized black or yellow crosslinked polyethylene (PEX) pipe made in pipe dimension ratios ranging from 6 to 17. Included are requirements and test methods for material, workmanship, dimensions, burst pressure, hydrostatic sustained pressure, stabilizer functionality, bent-pipe hydrostatic pressure, degree of crosslinking, chemical resistance, and minimum operating temperature. Requirements for pipe markings are also given. The pipe covered by this specification is intended for pressure or non-pressure oil and gas producing applications, such as conveying oil, dry or wet gas, gas gathering, multiphase fluids, and non-potable oilfield water. This specification does not cover piping for gas distribution applications.  
1.2 This specification also includes requirements for joints made between PEX pipe and polyethylene electrofusion fittings (specified in Specifications F1055 or F3373). Fittings to be used with PEX pipe manufactured to this Specification are in Specification F2829/F2829M. Installation considerations are in Appendix X3.  
1.3 The text of this specification references notes, footnotes, and appendixes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
Note 1: Metric sized (SI units) pipe should only be joined with corresponding metric sized fittings, and inch sized pipe should only be joined with corresponding inch sized fittings. Inch sized fittings should not be used for metric sized pipe, and metric sized fittings should not be used for IPS inch sized pipe.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the requirements and test methods for outside diameter controlled, pressure rated, black metric-sized and IPS-sized crosslinked polyethylene (PEX) pipe, fittings and joints intended for oil and gas producing applications. It presents the criteria for materials made in pipe dimension ratios ranging from 6 to 17, along with workmanship, burst pressure, hydrostatic sustained pressure, bent-pipe hydrostatic pressure, stabilizer functionality, degree of crosslinking, and chemical resistance. It also includes guidelines for pipe and fittings markings.
SCOPE
1.1 This specification covers outside diameter controlled, pressure rated, metric-sized and inch-sized black or yellow crosslinked polyethylene (PEX) pipe made in pipe dimension ratios ranging from 6 to 17. Included are requirements and test methods for material, workmanship, dimensions, burst pressure, hydrostatic sustained pressure, stabilizer functionality, bent-pipe hydrostatic pressure, degree of crosslinking, chemical resistance, and minimum operating temperature. Requirements for pipe markings are also given. The pipe covered by this specification is intended for pressure or non-pressure oil and gas producing applications, such as conveying oil, dry or wet gas, gas gathering, multiphase fluids, and non-potable oilfield water. This specification does not cover piping for gas distribution applications.  
1.2 This specification also includes requirements for joints made between PEX pipe and polyethylene electrofusion fittings (such as Specification F1055). Fittings to be used with PEX pipe manufactured to this Specification are in Specification F2829. Installation considerations are in .  
1.3 The text of this specification references notes, footnotes, and appendixes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
Note 1: Metric sized (SI units) pipe should only be joined with corresponding metric sized fittings, and inch sized pipe should only be joined with corresponding inch sized fittings. Inch sized fittings should not be used for metric sized pipe, and metric sized fittings should not be used for IPS inch sized pipe.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the requirements and test methods for outside diameter controlled, pressure rated, black metric-sized and IPS-sized crosslinked polyethylene (PEX) pipe, fittings and joints intended for oil and gas producing applications. It presents the criteria for materials made in pipe dimension ratios ranging from 6 to 17, along with workmanship, burst pressure, hydrostatic sustained pressure, bent-pipe hydrostatic pressure, stabilizer functionality, degree of crosslinking, and chemical resistance. It also includes guidelines for pipe and fittings markings.
SCOPE
1.1 This specification covers outside diameter controlled, pressure rated, metric-sized and inch-sized black or yellow crosslinked polyethylene (PEX) pipe made in pipe dimension ratios ranging from 6 to 17. Included are requirements and test methods for material, workmanship, dimensions, burst pressure, hydrostatic sustained pressure, stabilizer functionality, bent-pipe hydrostatic pressure, degree of crosslinking, chemical resistance, and minimum operating temperature. Requirements for pipe markings are also given. The pipe covered by this specification is intended for pressure or non-pressure oil and gas producing applications, such as conveying oil, dry or wet gas, gas gathering, multiphase fluids, and non-potable oilfield water. This specification does not cover piping for gas distribution applications.  
1.2 This specification also includes requirements for joints made between PEX pipe and polyethylene electrofusion fittings (such as Specification F1055). Fittings to be used with PEX pipe manufactured to this Specification are in Specification F2829. Installation considerations are in .  
1.3 The text of this specification references notes, footnotes, and appendixes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
Note 1: Metric sized (SI units) pipe should only be joined with corresponding metric sized fittings, and inch sized pipe should only be joined with corresponding inch sized fittings. Inch sized fittings should not be used for metric sized pipe, and metric sized fittings should not be used for IPS inch sized pipe.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the requirements and test methods for outside diameter controlled, pressure rated, black metric-sized and IPS-sized crosslinked polyethylene (PEX) pipe, fittings and joints intended for oil and gas producing applications. It presents the criteria for materials made in pipe dimension ratios ranging from 6 to 17, along with workmanship, burst pressure, hydrostatic sustained pressure, bent-pipe hydrostatic pressure, stabilizer functionality, degree of crosslinking, and chemical resistance. It also includes guidelines for pipe and fittings markings.
SCOPE
1.1 This specification covers outside diameter controlled, pressure rated, metric-sized and inch-sized black or yellow crosslinked polyethylene (PEX) pipe made in pipe dimension ratios ranging from 6 to 17. Included are requirements and test methods for material, workmanship, dimensions, burst pressure, hydrostatic sustained pressure, stabilizer functionality, bent-pipe hydrostatic pressure, degree of crosslinking, chemical resistance, and minimum operating temperature. Requirements for pipe markings are also given. The pipe covered by this specification is intended for pressure or non-pressure oil and gas producing applications, such as conveying oil, dry or wet gas, gas gathering, multiphase fluids, and non-potable oilfield water. This specification does not cover piping for gas distribution applications.  
1.2 This specification also includes requirements for joints made between PEX pipe and polyethylene electrofusion fittings (such as Specification F1055). Fittings to be used with PEX pipe manufactured to this Specification are in Specification F2829. Installation considerations are in .  
1.3 The text of this specification references notes, footnotes, and appendixes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
Note 1: Metric sized (SI units) pipe should only be joined with corresponding metric sized fittings, and inch sized pipe should only be joined with corresponding inch sized fittings. Inch sized fittings should not be used for metric sized pipe, and metric sized fittings should not be used for IPS inch sized pipe.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the requirements and test methods for high-density polyethylene (PE) materials, line pipes, and fittings used in pressure or non-pressure oil and gas producing applications to convey fluids such as oil, dry or wet gas, multiphase fluids, and non-potable oilfield water. This specification does not apply to pipes for gas distribution applications. PE material compounds suitable for use in the manufacture of pipes and fittings under this specification shall adhere to values of the following properties: density (natural base resin), melt index, flexural modulus, tensile strength at yield, SCG resistance, hydrostatic strength, color and UV stabilization, hydrostatic design stress, and hydrostatic design basis. The line pipes shall meet specific requirements as to workmanship, dimensions (outside diameter, toe-in, outside surface irregularity, ovality, wall thickness, and special sizes), inside surface ductility, tensile elongation, bendback resistance, elevated temperature sustained pressure, short-term strength and pressurization, apparent tensile strength at yield, and carbon black content. And conversely, PE fittings shall be manufactured in accordance with their intended use with correspondingly sized PE line pipes, as follows: socket fusion fittings, butt fusion fittings, electrofusion fittings, fabricated fittings, and transition fittings.
SCOPE
1.1 This specification covers requirements and test methods for high-density polyethylene (PE) materials, pipe and fittings for pressure or non-pressure oil and gas producing applications to convey fluids such as oil, dry or wet gas, multiphase fluids, and non-potable oilfield water. This specification does not cover pipe for gas distribution applications.  
1.1.1 For the purposes of this specification, high-density polyethylene material is Specification D3350 density cell classification 3 or higher. This specification does not cover materials having Specification D3350 density cell classification less than 3 such as medium or low density polyethylene materials.  
1.1.2 See Specification D2513 for polyethylene pipe and fittings intended for use in the distribution of natural gas, or for use with liquefied petroleum gas.  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, and markings for on-site manufactured multilayer reinforced polyethylene composite pipe. It covers nominal sizes 6 in. through 36 in. (150 mm through 915 mm). These multilayered reinforced polyethylene composite pipe products2 are assembled and installed in various lengths, including long continuous lengths. These products are intended for the transport of crude oil, natural gas and hazardous liquids in the rehabilitation of existing pipelines and for new pipelines.
Note 1: Hazardous liquids are those liquids defined by the U.S. Department of Transportation in 49 CFR 195.2.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, markings for factory manufactured multilayer flexible steel pipe with thermoplastic inner and outer layers and end connections (Fig. 1). It covers nominal sizes 2 in. through 8 in. (50 mm through 200 mm). Flexible steel pipes are multilayered pipe products manufactured in long continuous lengths and reeled for storage, transport and installation. The multilayer thermoplastic and flexible steel pipe governed by this standard are intended for use for the transport of crude oil, natural gas, hazardous chemicals, industrial chemicals and water.2  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the requirements and test methods for high-density polyethylene (PE) materials, line pipes, and fittings used in pressure or non-pressure oil and gas producing applications to convey fluids such as oil, dry or wet gas, multiphase fluids, and non-potable oilfield water. This specification does not apply to pipes for gas distribution applications. PE material compounds suitable for use in the manufacture of pipes and fittings under this specification shall adhere to values of the following properties: density (natural base resin), melt index, flexural modulus, tensile strength at yield, SCG resistance, hydrostatic strength, color and UV stabilization, hydrostatic design stress, and hydrostatic design basis. The line pipes shall meet specific requirements as to workmanship, dimensions (outside diameter, toe-in, outside surface irregularity, ovality, wall thickness, and special sizes), inside surface ductility, tensile elongation, bendback resistance, elevated temperature sustained pressure, short-term strength and pressurization, apparent tensile strength at yield, and carbon black content. And conversely, PE fittings shall be manufactured in accordance with their intended use with correspondingly sized PE line pipes, as follows: socket fusion fittings, butt fusion fittings, electrofusion fittings, fabricated fittings, and transition fittings.
SCOPE
1.1 This specification covers requirements and test methods for high-density polyethylene (PE) materials, pipe and fittings for pressure or non-pressure oil and gas producing applications to convey fluids such as oil, dry or wet gas, multiphase fluids, and non-potable oilfield water. This specification does not cover pipe for gas distribution applications.  
1.1.1 For the purposes of this specification, high-density polyethylene material is Specification D3350 density cell classification 3 or higher. This specification does not cover materials having Specification D3350 density cell classification less than 3 such as medium or low density polyethylene materials.  
1.1.2 See Specification D2513 for polyethylene pipe and fittings intended for use in the distribution of natural gas, or for use with liquefied petroleum gas.  
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification establishes the requirements and test methods for 1/2 in. through 14 in. multilayer polyethylene-polyamide (PE-PA) pipe, which is a two-layer pipe (PE pipe layer bonded to an inner layer of PA). It covers the multilayer pipe for use in piping applications where the permeation and chemical resistance of PA compounds may be useful to protect the PE pipe layer, such as oil and gas producing applications that convey oil, dry or wet gas, and multiphase fluids. Electrofusion and mechanical joints are typically used for this multilayer pipe.
SCOPE
1.1 This specification covers requirements and test methods for 1/2 in. through 14 in. multilayer polyethylene-polyamide (PE-PA) pipe, which is a two-layer pipe (PE pipe layer bonded to an inner layer of PA). The multilayer pipe covered by this specification is intended for use in piping applications where the permeation and chemical resistance of polyamide (PA) compounds may be useful to protect the PE pipe layer, such as oil and gas producing applications that convey oil, dry or wet gas, and multiphase fluids.Note 1—Permeability and chemical resistance depends on the type of PA used. The PA layer delays but does not prevent liquid hydrocarbons effects. Therefore, the hydrocarbon chemical design factor for this multilayer pipe should be the same as for PE pipe layer—see X1.2.  
1.2 Electrofusion and mechanical joints are typically used for this multilayer pipe.  
1.3 Unless specified otherwise, all the pipe requirements in this standard are for the multilayer pipe.  
1.4 The PA layer is not taken into consideration for the design pressure of multilayer pipe meeting this specification. Design pressure rating is determined from the PE pipe layer alone—see Appendix X1.  
1.5 Units—The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in figures and tables) shall not be considered as requirements of the standard.  
1.7 The following precautionary caveat pertains only to the test method portion, Section 6, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the requirements and test methods for outside diameter controlled, pressure rated, black metric-sized and IPS-sized crosslinked polyethylene (PEX) pipe, fittings and joints intended for oil and gas producing applications. It presents the criteria for materials made in pipe dimension ratios ranging from 6 to 17, along with workmanship, burst pressure, hydrostatic sustained pressure, bent-pipe hydrostatic pressure, stabilizer functionality, degree of crosslinking, and chemical resistance. It also includes guidelines for pipe and fittings markings.
SCOPE
1.1 This specification covers outside diameter controlled, pressure rated, black metric-sized and IPS-sized crosslinked polyethylene (PEX) pipe, fittings and joints, made in pipe dimension ratios ranging from 6 to 17. Included are requirements and test methods for material, workmanship, dimensions, burst pressure, hydrostatic sustained pressure, stabilizer functionality, bent-pipe hydrostatic pressure, degree of crosslinking, and chemical resistance. Requirements for pipe and fittings markings are also given. The pipe, fittings and joints covered by this specification are intended for pressure or non-pressure oil and gas producing applications to convey fluids such as oil, dry or wet gas, gas gathering, multiphase fluids, and non-potable oilfield water. This specification does not cover pipe for gas distribution applications.  
1.2 The text of this specification references notes, footnotes, and appendixes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.Note 1—Metric sized (SI units) pipe should only be joined with corresponding metric sized fittings, and inch sized pipe should only be joined with corresponding inch sized fittings. Inch sized fittings should not be used for metric sized pipe, and metric sized fittings should not be used for IPS inch sized pipe.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, and markings for on-site manufactured multilayer reinforced polyethylene composite pipe. It covers nominal sizes 6 in. through 36 in. (150 mm through 915 mm). These multilayered reinforced polyethylene composite pipe products are assembled and installed in various lengths, including long continuous lengths. These products are intended for the transport of crude oil, natural gas and hazardous liquids in the rehabilitation of existing pipelines and for new pipelines.
Note 1—Hazardous liquids are those liquids defined by the U.S. Department of Transportation in 49 CFR 195.2.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, markings for factory manufactured multilayer flexible steel pipe with thermoplastic inner and outer layers and end connections (Fig. 1). It covers nominal sizes 2 in. through 8 in. (50 mm through 200 mm). Flexible steel pipes are multilayered pipe products manufactured in long continuous lengths and reeled for storage, transport and installation. The multilayer thermoplastic and flexible steel pipe governed by this standard are intended for use for the transport of crude oil, natural gas, hazardous chemicals, industrial chemicals and water.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
FIG. 1 Cutaway of Flexible Steel Pipe

ABSTRACT
This specification covers the requirements and test methods for high-density polyethylene (PE) materials, line pipes, and fittings used in pressure or non-pressure oil and gas producing applications to convey fluids such as oil, dry or wet gas, multiphase fluids, and non-potable oilfield water. This specification does not apply to pipes for gas distribution applications. PE material compounds suitable for use in the manufacture of pipes and fittings under this specification shall adhere to values of the following properties: density (natural base resin), melt index, flexural modulus, tensile strength at yield, SCG resistance, hydrostatic strength, color and UV stabilization, hydrostatic design stress, and hydrostatic design basis. The line pipes shall meet specific requirements as to workmanship, dimensions (outside diameter, toe-in, outside surface irregularity, ovality, wall thickness, and special sizes), inside surface ductility, tensile elongation, bendback resistance, elevated temperature sustained pressure, short-term strength and pressurization, apparent tensile strength at yield, and carbon black content. And conversely, PE fittings shall be manufactured in accordance with their intended use with correspondingly sized PE line pipes, as follows: socket fusion fittings, butt fusion fittings, electrofusion fittings, fabricated fittings, and transition fittings.
SCOPE
1.1 This specification covers requirements and test methods for high-density polyethylene (PE) materials, pipe and fittings for pressure or non-pressure oil and gas producing applications to convey fluids such as oil, dry or wet gas, multiphase fluids, and non-potable oilfield water. This specification does not cover pipe for gas distribution applications.
1.1.1 For the purposes of this specification, high-density polyethylene material is Specification D 3350 density cell classification 3 or higher. This specification does not cover materials having Specification D 3350 density cell classification less than 3 such as medium or low density polyethylene materials.
1.2 Units—The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of each other. Combining values from the two systems may result in non-compliance with the standard. Values in parentheses are provided for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers coiled, machine-made glass fiber reinforced thermoplastic pipe up to 6 in. nominal size, having discrete, unbonded inner and outer layers of thermoplastic compounds and an intermediate structural layer of unbonded, dry glass fiber reinforcement to provide higher strength. Included are a classification system and requirements for materials, mechanical properties, dimensions, performance, methods of test, and marking. Reinforced thermoplastic pipes are used for oil and gas applications, including transport of multiphase fluids, hydrocarbon gases, hydrocarbon liquids and non-potable water. Physical requirements cover workmanship, dimensions and tolerances, pipe requirements (pressure design basis, cell classification, pipe re-categorization, bending requirements), fittings requirements, joint requirements (leak test, tensile pull test requirements, temperature cycling, elevated temperature test).
SCOPE
1.1 This specification covers coiled, machine-made glass fiber reinforced thermoplastic pipe up to 6 in. nominal size, having discrete, unbonded inner and outer layers of thermoplastic compounds and an intermediate structural layer of unbonded, dry glass fiber reinforcement to provide higher strength. Included are a classification system and requirements for materials, mechanical properties, dimensions, performance, methods of test, and marking. Reinforced thermoplastic pipes are used for oil and gas applications, including transport of multiphase fluids, hydrocarbon gases, hydrocarbon liquids and non-potable water.  
1.2 The piping system will comprise one or more runs of pipe along with mechanical fittings, designed and for use with this composite pipe, connecting them to each other and to the other pipeline components.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers coiled, machine-made glass fiber reinforced thermoplastic pipe up to 6 in. nominal size, having discrete, unbonded inner and outer layers of thermoplastic compounds and an intermediate structural layer of unbonded, dry glass fiber reinforcement to provide higher strength. Included are a classification system and requirements for materials, mechanical properties, dimensions, performance, methods of test, and marking. Reinforced thermoplastic pipes are used for oil and gas applications, including transport of multiphase fluids, hydrocarbon gases, hydrocarbon liquids and non-potable water. Physical requirements cover workmanship, dimensions and tolerances, pipe requirements (pressure design basis, cell classification, pipe re-categorization, bending requirements), fittings requirements, joint requirements (leak test, tensile pull test requirements, temperature cycling, elevated temperature test).
SCOPE
1.1 This specification covers coiled, machine-made glass fiber reinforced thermoplastic pipe2 up to 6 in. nominal size, having discrete, unbonded inner and outer layers of thermoplastic compounds and an intermediate structural layer of unbonded, dry glass fiber reinforcement to provide higher strength. Included are a classification system and requirements for materials, mechanical properties, dimensions, performance, methods of test, and marking. Reinforced thermoplastic pipes are used for oil and gas applications, including transport of multiphase fluids, hydrocarbon gases, hydrocarbon liquids and non-potable water.  
1.2 The piping system will comprise one or more runs of pipe along with mechanical fittings, designed and for use with this composite pipe, connecting them to each other and to the other pipeline components.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This specification covers coiled, machine-made glass fiber reinforced thermoplastic pipe up to 6 in. nominal size, having discrete, unbonded inner and outer layers of thermoplastic compounds and an intermediate structural layer of unbonded, dry glass fiber reinforcement to provide higher strength. Included are a classification system and requirements for materials, mechanical properties, dimensions, performance, methods of test, and marking. Reinforced thermoplastic pipes are used for oil and gas applications, including transport of multiphase fluids, hydrocarbon gases, hydrocarbon liquids and non-potable water.
Formerly under the jurisdiction of Committee F17 on Plastic Piping Systems, this specification was withdrawn in January 2023 in accordance with section 10.6.3 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.