SIST EN ISO 6892-1:2017

SLOVENSKI STANDARD
01-februar-2017
1DGRPHãþD
SIST EN ISO 6892-1:2010
Kovinski materiali - Natezni preskus - 1. del: Metoda preskušanja pri sobni
temperaturi (ISO 6892-1:2016)
Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO
6892-1:2016)
Metallische Werkstoffe - Zugversuch - Teil 1: Prüfverfahren bei Raumtemperatur (ISO
6892-1:2016)
Matériaux métalliques - Essai de traction - Partie 1: Méthode d'essai à température
ambiante (ISO 6892-1:2016)
Ta slovenski standard je istoveten z: EN ISO 6892-1:2016
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 6892-1
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2016
EUROPÄISCHE NORM
ICS 77.040.10 Supersedes EN ISO 6892-1:2009
English Version
Metallic materials - Tensile testing - Part 1: Method of test
at room temperature (ISO 6892-1:2016)
Matériaux métalliques - Essai de traction - Partie 1: Metallische Werkstoffe - Zugversuch - Teil 1:
Méthode d'essai à température ambiante (ISO 6892- Prüfverfahren bei Raumtemperatur (ISO 6892-1:2016)
1:2016)
This European Standard was approved by CEN on 15 April 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6892-1:2016 E
worldwide for CEN national Members.

Contents Page
European Foreword . 3
European Foreword
This document (EN ISO 6892-1:2016) has been prepared by Technical Committee ISO/TC 164
“Mechanical testing of metals” in collaboration with Technical Committee ECISS/TC 101 “Test methods
for steel (other than chemical analysis)” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2017, and conflicting national standards shall
be withdrawn at the latest by January 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 6892-1:2009.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 6892-1:2016 has been approved by CEN as EN ISO 6892-1:2016 without any
modification.
INTERNATIONAL ISO
STANDARD 6892-1
Second edition
2016-07-01
Metallic materials — Tensile testing —
Part 1:
Method of test at room temperature
Matériaux métalliques — Essai de traction —
Partie 1: Méthode d’essai à température ambiante
Reference number
ISO 6892-1:2016(E)
©
ISO 2016
ISO 6892-1:2016(E)
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

ISO 6892-1:2016(E)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 6
5 Principle . 7
6 Test pieces . 8
6.1 Shape and dimensions . 8
6.1.1 General. 8
6.1.2 Machined test pieces . 8
6.1.3 Unmachined test pieces . 9
6.2 Types. 9
6.3 Preparation of test pieces . 9
7 Determination of original cross-sectional area . 9
8 Original gauge length and extensometer gauge length .10
8.1 Choice of the original gauge length .10
8.2 Marking the original gauge length .10
8.3 Choice of the extensometer gauge length .10
9 Accuracy of testing apparatus .10
10 Conditions of testing .11
10.1 Setting the force zero point .11
10.2 Method of gripping .11
10.3 Testing rates .11
10.3.1 General information regarding testing rates .11
10.3.2 Testing rate based on strain rate (method A) .11
10.3.3 Testing rate based on stress rate (method B) .13
10.3.4 Report of the chosen testing conditions .15
11 Determination of the upper yield strength .15
12 Determination of the lower yield strength .15
13 Determination of proof strength, plastic extension.15
14 Determination of proof strength, total extension .16
15 Method of verification of permanent set strength .16
16 Determination of the percentage yield point extension .16
17 Determination of the percentage plastic extension at maximum force .17
18 Determination of the percentage total extension at maximum force .17
19 Determination of the percentage total extension at fracture .17
20 Determination of percentage elongation after fracture .18
21 Determination of percentage reduction of area .18
22 Test report .19
23 Measurement uncertainty .20
23.1 General .20
23.2 Test conditions .20
23.3 Test results.20
ISO 6892-1:2016(E)
Annex A (informative) Recommendations concerning the use of computer-controlled
tensile testing machines .34
Annex B (normative) Types of test pieces to be used for thin products: sheets, strips, and
flats between 0,1 mm and 3 mm thick .40
Annex C (normative) Types of test pieces to be used for wire, bars, and sections with a
diamet
...