SIST EN ISO 10993-3:2004

SLOVENSKI STANDARD
01-februar-2004
1DGRPHãþD
SIST EN 30993-3:2000
%LRORãNRRYUHGQRWHQMHPHGLFLQVNLKSULSRPRþNRYGHO3UHVNXVLJHQVNH
WRNVLþQRVWLNDQFHURJHQRVWLLQWRNVLþQRVWL]DUD]PQRåHYDQMH,62
Biological evaluation of medical devices - Part 3: Tests for genotoxicity, carcinogenicity
and reproductive toxicity (ISO 10993-3:2003)
Biologische Beurteilung von Medizinprodukten - Teil 3: Prüfungen auf Gentoxizität,
Karzinogenität und Reproduktionstoxizität (ISO 10993-3:2003)
Evaluation biologique des dispositifs médicaux - Partie 3: Essais concernant la
génotoxicité, la cancérogénicité et la toxicité sur la reproduction (ISO 10993-3:2003)
Ta slovenski standard je istoveten z: EN ISO 10993-3:2003
ICS:
11.100.20 %LRORãNRRYUHGQRWHQMH Biological evaluation of
PHGLFLQVNLKSULSRPRþNRY medical devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 10993-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2003
ICS 11.100 Supersedes EN 30993-3:1993
English version
Biological evaluation of medical devices - Part 3: Tests for
genotoxicity, carcinogenicity and reproductive toxicity (ISO
10993-3:2003)
Evaluation biologique des dispositifs médicaux - Partie 3: Biologische Beurteilung von Medizinprodukten - Teil 3:
Essais concernant la génotoxicité, la cancérogénicité et la Prüfungen auf Gentoxizität, Karzinogenität und
toxicité sur la reproduction (ISO 10993-3:2003) Reproduktionstoxizität (ISO 10993-3:2003)
This European Standard was approved by CEN on 1 October 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10993-3:2003 E
worldwide for CEN national Members.

CORRECTED  2003-12-03
Foreword
This document (EN ISO 10993-3:2003) has been prepared by Technical Committee ISO/TC 194
"Biological evaluation of medical devices" in collaboration with Technical Committee CEN/TC
206 "Biocompatibility of medical and dental materials and devices", the secretariat of which is
held by NEN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by April 2004, and conflicting national
standards shall be withdrawn at the latest by April 2004.
This document supersedes EN 30993-3:1993.
This document has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association, and supports essential requirements of EU
Directive(s).
For relationship with EU Directive(s), see informative Annex ZB, which is an integral part of this
document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and
the United Kingdom.
Endorsement notice
The text of ISO 10993-3:2003 has been approved by CEN as EN ISO 10993-3:2003 without any
modifications.
NOTE Normative references to International Standards are listed in Annex ZA (normative).
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 10993-2 1992 Biological evaluation of medical EN ISO 10993-2 1998
devices - Part 2: Animal welfare
requirements
ISO 10993-12 1996 Biological evaluation of medical EN ISO 10993-12 1996
devices - Part 12: Sample
preparation and reference
materials
Annex ZB
(informative)
Clauses of this European Standard addressing essential requirements or
other provisions of EU Directives
This European Standard has been prepared under a mandate given to CEN by the European
Commission and the European Free Trade Association and supports essential requirements of
EU Directive 93/42/EEC.
WARNING Other requirements and other EU Directives may be applicable to the
product(s) falling within the scope of this standard.
The following clauses of this standard are likely to support requirements of Directive 93/42/EEC.
Compliance with these clauses of this standard provides one means of conforming with the
specific essential requirements of the Directive concerned and associated EFTA regulations.
INTERNATIONAL ISO
STANDARD 10993-3
Second edition
2003-10-15
Biological evaluation of medical
devices —
Part 3:
Tests for genotoxicity, carcinogenicity
and reproductive toxicity
Évaluation biologique des dispositifs médicaux —
Partie 3: Essais concernant la génotoxicité, la cancérogénicité et la
toxicité sur la reproduction
Reference number
ISO 10993-3:2003(E)
©
ISO 2003
ISO 10993-3:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2003 — All rights reserved

ISO 10993-3:2003(E)
Contents Page
Foreword. iv
Introduction . vi
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 2
4 Genotoxicity tests. 3
4.1 General. 3
4.2 Test strategy. 3
4.3 Sample preparation. 4
4.4 Test methods. 4
4.4.1 In vitro genotoxicity tests. 4
4.4.2 In vivo genotoxicity tests . 4
5 Carcinogenicity tests. 5
5.1 General. 5
5.2 Test strategy. 5
5.3 Sample preparation. 5
5.4 Test methods. 5
6 Reproductive and developmental toxicity tests . 6
6.1 General. 6
6.2 Test strategy. 6
6.3 Sample preparation. 6
6.4 Test methods. 7
7 Test report. 7
Annex A (informative) Cell transformation test system . 8
Annex B (informative) Rationale of test systems. 9
Annex C (informative) Role of implantation carcinogenicity studies. 11
Bibliography . 13

ISO 10993-3:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10993-3 was prepared by Technical Committee ISO/TC 194, Biological evaluation of medical devices.
This second edition cancels and replaces the first edition (ISO 10993-3:1992), which has been technically
revised.
ISO 10993 consists of the following parts, under the general title Biological evaluation of medical devices:
 Part 1: Evaluation and testing
 Part 2: Animal welfare requirements
 Part 3: Tests for genotoxicity, carcinogenicity and reproductive toxicity
 Part 4: Selection of tests for interactions with blood
 Part 5: Tests for in vitro cytotoxicity
 Part 6: Tests for local effects after im
...